Search Documents

By P. Mokwena

Paper written on project work carried out in partial fulfilment of BSc (Hons) in Chemical Engineering Diamond synthesis has attracted a great deal of interest because of its exceptional properties and various applications. In this study, the chemical catalytic vapour deposition (CCVD) method was used to synthesize diamond films using acetylene as carbon source and hydrogen as carrier gas at a temperature of 1000°C, and their thermodynamic stability was studied. Photographic analysis revealed that these products are diamond films, Ramman spectroscopy confirmed that they are graphitic while confocal laser scanning microscopic image analyses proved that these diamonds films have structural defects due to iron impurity from the catalyst precursor. The quantity of diamonds films produced is also proportional to the acetylene to hydrogen ratio but these films are larger in size at lower acetylene to hydrogen ratio. Thermogravimetric analyses showed that transformation of these materials begins at 25°C but could not be used to determine if a temperature range below 25°C exists. The stability of these CCVD-synthesized diamonds also increases below 25°C when stored at different temperatures.

Jan 1, 2007

By H. Krogerus, P. Niemelä, P. Oikarinen

High carbon ferrochromium is produced by carbon reduction. No replacement for carbon as reductant has yet been developed. The reduction creates a considerable amount of CO-gas. In open and semi-closed furnaces the gas is burned when leaving the burden. In closed furnaces the formed gas is sucked out by a fan, washed and utilised as fuel. The formation of carbon monoxide is presented briefly starting from thermodynamic considerations up to solid and liquid state reduction. The volume, composition and energy content of the furnace gas are discussed, focusing on the raw materials and pre-treatment processes of the furnace feed as well as on the process equipment and control. Outokumpu has been using closed and sealed furnaces and utilising the CO-gas in its Tornio Ferrochrome Works since 1968. Today in Tornio with an annual ferrochromium production of 260 000 t CO-gas production is 186 million m3, representing 68 MWh an hour. At the same time the furnace power input is 95MW. About 98 % of the CO-gas is utilised, whereof 30% in the ferrochrome production itself. This paper focuses on the characteristics and utilisation of CO-gas. CO-gas is secondary energy, which on one hand saves primary electric and fossil fuel energy in ferrochromium production and, on the other, replaces other fossil fuels at the adjacent steel works. The characteristics of the fuel, requirements for utilisation as well as health and safety aspects are discussed. Utilisation of the gas has a high impact on the total dust and gaseous emissions and on the energy optimisation at the ferrochromium and steel works.

Jan 1, 2004

A Life Cycle Assessment (LCA) of stainless steel production, including that of the nickel, ferronickel, ferrochromium and iron feedstocks was carried out using inventory data derived from the literature. The environmental impact categories considered in the study were Global Warming Potential (GWP), Acidification Potential (AP) and total (or full cycle) energy consumption. The effects of different sources of electricity (black coal, natural gas and hydroelectricity) were also examined in the study. The results of the LCA showed that when ferronickel is used as the nickel source, the total energy consumption for stainless steel production is approximately 50% higher than when nickel metal is used as the nickel source (75 MJ/kg cf. 49 MJ/kg). This result comes about largely because the Fe units in ferronickel have a much higher energy intensity than do the Fe units in pig iron, and the greater the use of the former at the expense of the latter, the greater is the total energy consumption. The results also showed that the production of ferronickel made by far the largest contribution (59%) to the total energy consumption for stainless steel production when this feedstock is used as the nickel source, but when nickel metal is used as the nickel source the contributions of the various stages are more evenly distributed. It was also observed that the electricity consumption of the electric furnaces used in the production of ferronickel, ferrochromium and stainless steel contributed approximately 50% to the total energy consumed in stainless steel production. Given the relatively low efficiencies associated with electrical power generation, significant reductions in the total energy of stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel, ferrochromium and/or stainless steel smelting stages, for example by utilising bath smelting processes.

Jan 1, 2004

By G. R. Lane, A. Vermeulen, S. van de Venter, S. Bhoowanpursadh

Over the past two years Anglo Platinum made use of the specialist skills of Cyest Corporation to develop a Mine Optimization Tool (MOT) to enhance the current suite of in house mine planning tools and processes. The application was built in a multidimensional modelling environment developed by Cyest called CarbonL. This has allowed complex modelling that is transparent to the business users and therefore is not prone to the ?black box? approach that generally exists with these types of complex tools. The purpose of the MOT is to have an integrated software tool that can schedule production activities by half level for a shaft complex, while at the same time integrating the economics concomitant with that schedule. The tool allows the user to configure all activities relevant to the selected mining method, define the mine design parameters and geological parameters, define scheduling rules and then schedule all activities. This allows the user to test various production strategies and schedules very quickly and easily in terms of shaft value, costs and revenue profiles, labour complement and production ramp up so as to determine the option that best fits the overall strategy. This allows assessments of multiple scenarios in a relatively short period of time, after which only the best option is taken forward for graphic design and scheduling. This paper discusses briefly the rationale behind the Mine Optimisation Tool and the underlying workings of the modules that comprise the tool. It also covers the life cycle of this tool from the original prototype through to the final Mine Optimisation Tool software and discusses the positioning of the final tool.

Jan 1, 2007

By Andrew Jones

This paper discusses the worldwide market and cost environments for the bulk ferroalloys namely manganese alloys (ferromanganese, silicomanganese), ferrosilicon and ferrochrome (high-carbon ferrochrome, charge chrome). Annual average market prices since 1993 are presented graphically and analysed, and the main supply and demand trends for manganese, ferrosilicon and ferrochrome are summarized. The paper shows carbon and stainless steel output data for 1995, 2000 and 2005, mainly to demonstrate the rising importance of China as a ferroalloys market. Developments in ferroalloys capacity worldwide from 1991 to 2007 are discussed (plant start-ups and closures, ownership changes). Finally, the paper examines developments in the main cost factors for the bulk ferroalloys, i.e., chrome and manganese ore, electricity, carbon reductants and labour. Note that data for 2006 are estimated based on information available in November 2006.

Jan 1, 2007

By I. Alp

Application of magnetic separation was investigated for the enrichment of colemanite ores by removing the magnetic gangue fraction. The detailed XRD analysis of the ore has indicated that the gangue fraction is composed predominantly of the iron-bearing silicates such as smectite and, to a lesser extent, illite. Magnetic susceptibility measurements of the colemanite and gangue samples have proved that colemanite is diamagnetic in character whereas gangue fraction is weakly paramagnetic to allow the removal of this fraction by magnetic separation. Magnetic separation of the crushed and sized ore samples (-5 mm +75 µm) was performed using a high intensity permanent magnetic separator. Under the test conditions a colemanite concentrate (41.29 wt.% B2O3) was found to be produced from the crushed ore (30.76 wt.% B2O3) at a recovery of 96.76%. These findings suggest that magnetic separation has great potential as an alternative process for the production of a concentrate of commercially sufficient grade.

Jan 1, 2009

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By David Mitchell, Daan Delport, Frik Marx, Mike Shapiro

The use of copper cooling elements to enhance refractory lining life in pyrometallurgical vessels is common in modern furnace design. Copper elements typically incorporate a base panel with cast in cooling passages and an integral extended surface (formed of pins, fins or similar) onto which suitable refractory material is cast. The metallic, conducting parts are located towards the cold face of the lining, with the refractory material interposing between the coolers and the process. The coolers are designed to arrest wear of the refractory material by freezing a layer of slag or partially reacted material onto the hot face, thereby rendering the lining inert to further attack [1]. These coolers have achieved success in new furnaces and relining of existing vessels. The freeze layer is prone to mechanical damage during operational and process instability. The coolers must be capable of extracting the additional heat flux under upset conditions to facilitate rapid self-repair of the freeze layer and prevent further refractory wear in the intermittently exposed areas. However, operational experience has shown that the high heat flux capabilities of the copper coolers have some disadvantages, especially in processes producing vapours which form corrosive compounds when condensing onto the cold surfaces of the coolers. When corrosive conditions develop, the entire composite will fail due to loss of structural integrity, and as a result of leaks from the cooling water passages. This paper describes recent developments in the approach to the design and manufacture of copper cooler panels customized to achieve specified heat fluxes and temperature profiles, thereby reducing the formation of corrosion mechanisms in applications with corrosive gaseous environments and enhancing refractory lining life. Condensation formation prevention is achieved by adjusting the geometry of the cooler and selection of suitable materials of construction.

Jan 1, 2007

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015

By B. Larsen, S. Z. Nascimento, K. Fidje, J. P. M. Amaro, H. Gran

Safe and good operation of Søderberg electrodes is dependent upon high quality electrode paste coupled with correct electrode operating procedures. Good electrode performance depends further on proper melting and densification of the electrode paste. The melted paste should form a dense and viscous layer that prevents gasses from the baking process to move upwards. Both paste cylinders/blocks and briquettes can be used, but the procedures may differ between the various types of paste products. For briquette columns the formation of the important viscous layer is obtained through melting and densification of the briquettes. By basic rheological studies of electrode paste and by laboratory tests of briquette beds at isothermal conditions we have achieved a better understanding of the melting process. The effects of temperature gradients, pressure and friction between the briquettes and the electrode casing have also been evaluated qualitatively in pilot scale experiment and in industrial scale tests. The paper shows that melting and densification starts at a considerable lower temperature than the pitch softening temperature. It is concluded that the formation of a briquette electrode column depends on parameters as temperature, briquette column pressure and the friction. Operating conditions influencing the above parameters should be defined and established for each specific furnace operation. Such factors are e.g., charging and slipping procedures, column heating and electrical conditions.

Jan 1, 2004

By P. Dennis, T. Pieters, A. De Kievit, S. Ganguly

TEMCO has been producing manganese ferroalloys in submerged arc electric furnaces for over 40 years. The furnace linings all along have been of conventional insulation type until 2001 when a freeze lining of UCAR concept was installed for a 20 MW Furnace. Continuous improvement of furnace lining performance has been a key component in improving the business competitiveness of TEMCO. The expected minimum campaign life of the freeze lining is fifteen years as compared to the ten years of the conventional linings. The success of the freeze lining is very critical to the quanta and direction of heat flow through the lining that control the freeze protection. Under freeze protection can lead to reduced lining life and over freeze protection, on the other hand, can lead to operating difficulties and loss of smelting efficiency. It was, therefore, necessary to develop a computer based system to monitor and control the freeze protection. The computer based monitoring and control system uses the basic principles of heat transfer, activeX object and heat flux from dual thermocouples and that is reviewed.

Jan 1, 2004

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By M. Tangstad, B. Monsen, H. Midtgaard

The increased attention towards reducing emissions of fossil CO2 due to its potential global warming effect has resulted in a focus on renewable resources, as charcoal. Since charcoal is produced from growing wood it does not contribute to global warming. This paper gives a brief review of consequences of and reasons for using charcoal in the silicomanganese (SiMn) production. Results are presented from practical SiMn smelting experiments, on a pilot scale, using charcoal as reduction material and comparing with coke. As slag- and CO2-reactivity are important for furnace performance these features have also been measured.

Jan 1, 2004

By H. Yavuz

Closed form solutions assume opening shape to be circular to simplify the calculation of the ground response curve for the design of underground openings. However, in mining and civil engineering works, non-circular openings are commonly excavated. Therefore, there is a need to estimate the ground response curve for such openings. In this respect, a simple model for circular, arch and rectangular shape underground openings subject to a hydrostatic stress field is the aim of this study. A comprehensive numerical modelling, using the finite difference method, based on numerical modelling code FLAC version 4.0, was carried out. In addition to shape of an opening, the effect of rock mass strength, opening size, in situ stress on strain (tunnel deformation to tunnel radius) of the opening in response to applied support pressures was investigated parametrically by developing models for each specific condition. The strain results for each excavation shape obtained from this large number of models against the normalized strength of rock mass and internal support pressure with in situ stress magnitude were evaluated by multiple regression analysis. As a result, a model that was well correlated to data was developed for an overall estimate of the ground response curve depending on relevant effecting parameters. The regression coefficients of the model were given for estimating both roof and sidewall response curve of each excavation shape. The model was verified by statistical tests and by an analytical solution. Diagrams were also established to highlight the influence of relevant parameters and to estimate the support pressure for a stable opening staying within the acceptable limits of strain. Strains occurring in a rectangular opening are found to be larger than those in the arch and circular openings for the other fixed parameters. In the mean time, larger strains occur around an arch shape opening than a circular opening.

Jan 1, 2006

By G B. Gnoinski

The Skorpion Zinc Mine and Refinery is situated approximately 25 km north of Rosh Pinah, south-western Namibia. The supergene zinc oxide deposit at Skorpion is hosted in a volcano-sedimentary succession within the para-autochthonous Port Nolloth Zone of the Gariep Belt. Rock types hosting the ore deposit include altered and metamorphosed volcaniclastic and clastic sediments, limestone and rhyolite. At Skorpion, the metallurgical process is unique and the plant design requires minimal fluctuations within a selected feed grade. In addition, the presence of limestone inter-fingered with ore in some areas of the deposit results in dilution problems which may increase gangue acid consumption and therefore processing costs. Hence, selective mining is necessary to ensure the delivery of suitable ore to the processing plant, in order to keep the overall operating costs at a minimum. A complex control system is in place and is capable of a high degree of selectivity. The paper describes the grade control system in place at Skorpion Mine which ensures that the qualities of the blocks planned for mining and the material being mined meet the stringent process requirements of the refinery, i.e zinc grade, gangue acid consumption and deleterious elements that may impact on the efficiency and costs of the metallurgical process. Keywords: Skorpion zinc, zinc oxide, supergene, volcano-sedimentary, grade control

Jan 1, 2007

By Dennis Van Heerden

Southern Africa has a long history of underground hard rock mining dating back to the late 1800?s. The rock support of underground excavations has significantly changed during this period, due to improved technology, experience gained and rock support requirements by mining and geotechnical engineers. This paper examines the available underground rock support methods in Southern Africa with emphasis on the types and characteristics of: - Rock bolt types. - Rock bolt and long anchor grouts. - Thin-sprayed liners. - Sprayed Concrete. - Ground consolidations through injection methods. - Cavity and void filling with aerated cement products. [ ]

Jan 1, 2007

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By B. R. Broekman, K. J. R. Ford

Over the last decade significant development and use has been made of a simulation model that describes the HCFeMn smelting operations in Assmang Ltd. This spreadsheet based, semi-empirical, predictive model is derived from data from the submerged arc furnaces at Assmang?s Cato Ridge, KwaZulu-Natal smelter site. Departures from the empirical base case mass balance due to changes in the ores, reductant feeds and operating parameters are accounted for by use of fundamental relationships and heuristic type ratios which are applied in an iterative manner in the model. The model performs a sequential set of calculations to iteratively converge on a fully consistent mass and energy balance solution, which predicts Mn alloy and slag output masses and compositions for a given set of feeds. 440 MWh per operating day is used as the basis of energy input. The paper describes the key model components, assumptions made and calculation approach. Added to the mass and energy balance is a cost and revenue balance, which allows prediction of the economic performance for each simulation. Substantial use of the model has been made in simulating the performance of the current Assmang HCFeMn furnaces for both smelter investigations and future production planning. The model has also been a valuable tool in the strategic analysis of the use of future Mn ores and has formed the vital link between mine ore grades (metal and slag elements) and the expected alloy output, grade and profitability. Additionally, the model has been used in benchmarking exercises to predict other Mn smelting operations with remarkable accuracy. The paper highlights some aspects of the approaches taken in using the model to benchmark Assmang?s own furnace performance and cost competitiveness with other producers. For Assmang the development and application of this modelling technology has led to transformation in understanding of the Assmang HCFeMn furnace operations and increased awareness of the potential of its Mn ore bodies.

Jan 1, 2004

By J. L. van Niekerk

The research project reported on represents the first comprehensive attempt to measure the vibration levels of a variety of tools and equipment in the South African mining industry to determine the effect thereof on the health of workers and operators. Although human vibration has been studied extensively internationally only one reference pertaining to the South African mining industry could be found. From studies conducted in Canada and elsewhere it was evident that rock drills do have potentially hazardous levels of vibration. The scope of the research included measurements on a broad spectrum of tools, machines and vehicles used in the South African mining industry. Both hand-arm vibration, where the majority of the vibration enter the body through the hands, and whole body vibration, where the whole body is exposed to vibration through contact by the buttocks or feet, were investigated and measured. More than 700 sets of vibration data measured on 70 machines at 15 mines and workshops were obtained. Data were obtained for at least 24 different types of equipment and machines that were previously judged to have medium to high levels of vibration. All measurements were conducted in accordance with the international standards: ISO 5349, on hand-arm vibration, and ISO 2631-1, for whole body vibration. The equipment with the highest vibration levels in the hand-arm category was: rock drills, both pneumatic and hydraulic; pavement breakers and jackhammers; hand-held compactors; pneumatic wrenches and electrical hammer drills. Of these the rock drills had weighted vibration levels in excess of 20 m/s2. As far as whole body vibration was concerned the highest values were measured on earth-moving equipment. The major conclusion from this study is that the measured vibration levels are sufficiently high to create an enhanced level of risk of vibration-induced disorders in a significant proportion of the operators of hand-held equipment. The most notable examples are hand-held rock drills, pavement breakers, jackhammers and certain selected workshop tools. The results of the study indicate that a comprehensive epidemiological study should be undertaken on present and past workers to determine the prevalence of vibration-induced disorders.

Jan 1, 2000

By P. J. Bartlett

Premier Diamond Mine exploits a kimberlite orebody using cave mining methods. A drilling level is established at the base of a block of ore to effect undercutting that leads to caving of the overlying ore. A second level is developed some 15 metres below the undercutting level to allow extraction of the ore once it has caved. As much as 45 per cent of the rock is removed on the extraction level creating a series of pillars. Undercutting creates abutment stresses, as high as 3 times the virgin stress, which affect the rock mass to a distance of 20 metres from the undercut face on the undercut level and on the extraction level 15 metres below. If the extraction level is completely developed prior to undercutting, where stress levels exceed 20 percent of the rock mass strength, extensive rock mass and support damage occurs as the undercut passes overhead. Rock mass damage takes the form of movement along existing joints and minor shear failure through intact rock. Support damage takes the form of cracking in rigid concrete linings. Where induced stresses exceed 50 per cent of the rock mass strength it is often impractical to keep excavations on the extraction level open. Rock mass damage takes the form of extensive failure of the rock in shear which evidences itself as propagation of the fracture zone around tunnels and footwall heave. Support damage results in destruction of shotcrete linings and concrete footwalls. As the interbolt support fails, badly fractured rock ravels around the steel tendons. Observation and monitoring at Premier Mine and on other cave mines has shown that induced stress levels and consequent damage are a function of :?the extraction ratio on the undercut and extraction level prior to undercutting ?the shape of the undercut face ?the rate of undercut advance ?the distance of leads and lags between adjacent tunnels on the undercut level. To ensure the stability of excavations, all of the above parameters must be carefully planned and the planned mining sequence rigidly enforced. The minimum of development is completed on the extraction level prior to the undercut passing overhead. Required development is then rapidly completed once the area has been de-stressed. Support is installed in three phases: ?Rockbolts are installed as soon as excavations are developed ?Wire mesh, steel tendon straps and a layer of shotcrete sufficient to protect the mesh and straps from damage by blasting and LHD loading is installed as soon as practical thereafter. Inevitably the shotcrete lining has to be replaced once the undercut has passed overhead.. ?Rigid shotcrete linings and concreted footwalls are completed only after the undercut has passed overhead and the area has been de-stressed.

Jan 1, 2000