Search Documents

By G. G. Rogers, A. Vna Der Linde, N. B. Strydom, W. H. Van Der Walt

Changes in the level of serum vitamin C in mineworkers by N. B. STRYDOM, M.Se., Ph.D. (Illinois) (Fellow), G. G. ROGERS, M.Se. (Pta) (Visitor), W. H. VAN DER WALT, B.Se. (Poteh.) (Visitor), and A. VAN DER LlNDE, B.Se. (O.F.S.) (Visitor) The levels of serum vitamin C in the blood of mineworkers were determined on the first and fifth days of the normal heat-acclimatization period (i.e., before and after exposure to heat) and again after I, 2, and 4 months of underground employment. Supplementary vitamin C was administered to the men during the heat-acclimatization period. Six groups of 20 men featured in the study and, except for one of the two 4-month groups, all the values were obtained after a full shift of underground work. It was found that adequate levels of serum vitamin C were maintained during the heat-acclimatization period, and the 250 mg of vitamin C given daily to each man must therefore be regarded as sufficient. The serum vitamin C decreased significantly with time of exposure to underground conditions, showing that the vitamin C utilized during heat stress is more than that provided in the men's diet. At the end of 4 months, not a single subject had more than 0,4 mg of serum vitamin C per 100 ml, most of them having only 0,3 mg per 100 ml; 90 per cent of the men had had more than 0,4 mg per 100 ml during the acclimatization period. It is therefore recommended that the mineworkers' diets should be supplemented with 100 to 200 mg of vitamin C per man per day.

Jan 5, 1977

Specifile compendium' 80. Mining and engineering. (Obtainable from Specifile, P.O. Box 7870, Johannesburg 2000.) Reviewer: J. D. Austin SKF Steel. Plasmasrnelt information brochure. Hofors (Sweden), SKF Steel, 1980. Reviewer: N. A. Barcza POTENTIAL VALUE OF COLLIERY DISCARD MATERIAL By R B MacGillivray, Pr Eng, BSc(Eng) Rand, C Eng (Fellow) Preprints of perhaps the most thought-provoking of the papers delivered at the Witbank Coal Colloquium - 'Potential value of colliery discard material' by Roy MacGillivray of Rand Mines - are available on request from the South African Institute of Mining and Metallurgy. Mr MacGillivray outlines an imaginative plan to utilize the annual nine million tons of colliery discard in the WitbankBethal areas. Two SAIMM colloquia The South African Institute of Mining and Metallurgy (SAIMM) is organizing two one-day colloquia in the State Pavilion, Milner Park showgrounds, Johannesburg, to coincide with the Electra Mining Exhibition on 16th and 17th September. Over a million rands worth of equipment will be on display, the Electra Mining Exhibition being rated among the four or five largest in the world. The 1978 Electra Mining Exhibition was attended by 24 000 visitors. "Project Management in the Metallurgical Industry", "Mine Fires" APCOM International Conference by H. W. GLEN The 17th APCOM Conference (under the auspices of the Council for the Application of Computers and Mathematics in the Mineral Industries) was to have been held in Moscow during the last week in October. South Africans have always given enthusiastic support to the APCOM series of meetings, since their inception in 1961. The conference was held in the Republic in 1972.

Jan 1, 1980

By J. D. Austin, D. G. Kringe

Rates of return realized on investments in the gold mines of the newer goldfields outside the Witwatersrand were calculated and analysed over various time intervals and on various bases. It is shown that these rates of return are strongly correlated with changes in the gold price and cannot be equated with the returns that are expected when investments are made, and that the changes in gold price also affect the rates of return on the Johannesburg Stock Exchange as a whole. These correlations are used, together with a limited application of the Capital Asset Pricing Model, to suggest the expected levels of threshold returns in real terms for new mining projects, for projects on existing mines, and for share valuations.

Jan 1, 1980

By D. J. Adams, R. G. Gürtunca

In situ measurements and numerical modeling based on elastic theory showed that backfill stresses are considerably higher than originally thought. This has led to a change in understanding of rockmass behaviour. After describing previous work on the behaviour of the rockmass, this paper discusses possible reasons for the high stresses measured in backfil, and identifies the rockmass mechanisms possibly generating these stresses. It is concluded that the joints and the geological stratigraphy can lead to increased elastic convergence, and that the inelastic behaviour of the rockmass is also partly responsible for the increased closure measured in backfill. The use of an in situ modulus is suggested as an interim solution until a new computer model that allows for joints, different layers, and inelastic closures becomes available.

Jan 1, 1991

By Axel Schulze

HUGO PETERSEN has developed from the traditional firm of the same name that was established in 1906 in Berlin and is an engineering company specialising in general plant engineering now based in Wiesbaden. HUGO PETERSEN has many years wide-ranging experience in process plant engineering, primarily in the field of Sulphuric Acid Processes and Gas Cleaning. Together with its main shareholder, Chemieanlagenbau Chemnitz GmbH (CAC), a company with over 40 years experience in the international plant engineering business, HUGO PETERSEN implements turnkey new plants from initial consultancy right through to commissioning. In addition, HUGO PETERSEN can offer its clients improvements and revamps of existing plant systems. Initial consulting, planning and implementation take place within the context of a lean company organisation with experienced engineers and specialists. In all respects, many years of experience guarantee expertise over a wide range of possible applications For clients from the chemicals and metallurgical industries, as well as those in metals processing, HUGO PETERSEN GmbH?s breadth of experience means not just an efficient introduction to new methods and processes, but also their full implementation. In addition, along with design and construction for individual components, the company?s range of services also covers supply of complete plants, as well as modernisation projects and revamps in line with local conditions and existing quality requirements With own technologies and patents in the field of gas cleaning and sulphuric acid, supplemented by licences and cooperation projects, HUGO PETERSEN ensures expertise over a wide range of applications. With specialists and expert knowledge in these fields of application, HUGO PETERSEN is your partner of choice, supporting you and bringing your acid, and project to a successful conclusion.

Jan 1, 2009

By M. Rudolph, E. Schach

Tecflote is a new group of nitrile-based collectors for sulfide flotation. Water insolubility results in some interesting implications for the actual mechanism. It is not yet understood if Tecflote is directly adsorbed on the mineral surface as emulsion droplets or if it is only active at the air-water interface, affecting the interfacial rheology or electrostatic- and Van der Waals interactions, which have a direct impact on the bubble-particle contact. Different investigations including contact angle measurements, AFM studies and micro-flotation experiments are conducted to obtain a better understanding of the actual mechanism of Tecflote. Due to the reagent’s insoluble character, the Langmuir-Blodgett technique is used to investigate its behaviour in the air-water interface and to deposit defined layers of Tecflote on mineral substrates for the above-mentioned studies. An interferometric set up is used to investigate the influence of Tecflote on the film thinning between an air bubble and a mineral substrate. In addition, possible synergistic effects for the combination of Tecflote and conventional frothers (e.g. MIBC) are studied. Keywords: Sulfide flotation, insoluble collector

Jan 1, 2020

By Q. Zhang, X. C. Wang, S. Mao

Phosphate ore is an important strategic mineral resource in which apatite is the main valuable mineral. Flotation is the most commonly used method to separate apatite from middle-low grade phosphate rock. Selective flotation separation is based on the difference of physical and chemical properties of minerals occurring at the three interfaces of mineral/bubble/water. Surface and interface chemistry of mineral have been playing an important role in interpreting and governing its flotation phenomenon. In-situ, visualized and high-precision analytical techniques, such as Time-of-Flight Secondary Ion Mass Spectrometry, Atomic Force Microscopy and Molecular Simulation, have been applied to explore and uncover microscopic nature of apatite flotation. Consequently, a great progress at molecular or atomic level on surface and interface chemistry of apatite flotation has achieved in the past decades. In this paper, the research progress of surface and interface chemistry of apatite flotation such as surface wettability, surface-charging characteristics, surface dissolution behavior, adsorption mechanisms of fatty acid collector and depressor on apatite surface were systematically reviewed. This review will be helpful for the development of more selective reagents and efficient technologies for apatite flotation. Keywords: Apatite, Flotation, Surface and interface chemistry, Surface analysis technology

Jan 1, 2020

By J. S. Preston

The properties of some recently developed solvent-extraction reagents for the separation of cobalt and nickel sulphate solutions are reported. New commercial extractants based on alkyl phosphonic and alkyl phosphinic acids are described. These reagents show much improved selectivity for cobalt compared with established extractants. Some novel extractants developed at Mintek for the selective recovery of nickel in the presence of cobalt are also described. These reagents, which are based on mixtures of carboxylic acids and non-chelating oximes, are of interest in that no commercial nickel-selective reagents are currently available. Graphs showing metal loading and stripping, and pH-functionality, are presented. together with details of the metal separations achieved in batch countercurrent- extraction experiments with the various reagents.

Jan 1, 1983

By A. Navarra, A. Quelopana

The mine production scheduling problem (MPSP) has been studied since the 1960s, and remains an active area of computational research. In extending the concepts of the MPSP, the automated mine may now be regarded as a hierarchical intelligent agent in which the bottom layer consists of distributed robotic equipment, while strategic functionality occupies the higher layers. Here we present a disambiguation of artificial intelligence, machine learning, computational optimization, and automation within the mining context. Specifically, the Q-learning algorithm has been adapted to generate the initial solutions for a high-performing strategic mine planning algorithm, originally developed by Lamghari, Dimitrakopoulos and Ferland, based on the variable neighbourhood descent (VND) metaheuristic. The hierarchical intelligent agent is presented as an integrative conceptual platform, defining the interaction between our new Q-learning adaptation and Lamghari’s VND, and potentially other hierarchically controlled components of an artificially intelligent mine, having various degrees of automation. Sample computations involving Q-learning and VND are presented.

Dec 1, 2021

The theory of geostatistics covers a branch of .applied statistics aimed at a mathematical description and analysis of geological observations. Geostatistics can be used in pure geology (for example, for the analysis of trace elements in a metamorphic rock), in mineral exploration (for example, for the analysis of geochemical exploration data), as well as in mine valuation. This book is intended to provide a practical introduction to the theory of geostatistical methods of mineral evaluation. Over the years, various mathematical models have been developed to represent the distribution of values in mineral deposits. The simpler models are based on the assumption that the values are randomly distributed. Classical statistical methods, based on this assumption of the random distribution of values, are used to analyse mineral deposits to which these models apply or are assumed to apply. In all mineral deposits, however, one recognizes the presence of areas where the values are higher or lower than elsewhere. Also, the values of two samples in a mineral deposit are more likely to be similar if the samples are taken close together than if they are taken far apart. This indicates that there exists a degree of correlation between sample values, and that this correlation is a function of the distance between the samples. Models have been developed which take this correlation into consideration, with the degree of correlation between sample values being usually measured by the semivariogram function. In these models the fact that two samples taken next to each other will most probably not have the same value, must also be considered; even for very short distances the correlations are usually not perfect and a purely random component is present in the value distribution. The mathematical models will therefore assume the presence of two sources of variability in the values: a correlated component and a random component. Finally, one must consider the particular and very common case of mineral deposits in which the values present a systematic variation in space. This variation is usually referred to as a drift, or a trend. For example, the grade of an ore body may increase with depth of the ore, or it may decrease when one moves away from a central volcanic pipe. The earlier models did not give a satisfactory representation of drifts, and more complex models have been developed, in which three sources of variation are represented. These models are made up of: a deterministic component, a correlated component, and a random component. The deterministic component is used as a model of the drift. The correlated component explains regular changes in values which are not represented by the drift. The random component represents variations which cannot be explained by any of the above factors. The simpler models, based on the assumption of a single random component, will be described first (Chapter 2). The models based on the hypothesis of the superimposition of a correlated component on a random component, will then be analysed in detail. These models are most commonly used in the analysis of mineral deposits (Chapters 3-1 I). Finally, how to deal with the presence of a drift will be briefly described (Chapter 12). This book has been written essentially for students in mining engineering and for mining engineers who are interested in the background to the theory of geostatistics as well as its practical applications. The assumption is made that the reader has an elementary knowledge of statistics. Some knowledge of linear algebra is useful in part of Chapter 9, and is necessary to read Chapter 12. A proof is given of all the equations related to geostatistics, and which are not usually found in elementary textbooks on statistics. Understanding of these proofs is not necessary for practical application of the theory, and the reader may wish to skip them on a first reading, concentrating attention on the numerous simple practical examples given. Although the theoretical geostatistician will not find much new material in this publication, it is anticipated that he will develop some interest in the practical approach chosen to prove the various geostatistical equations. Many people and institutions contributed to the preparation and completion of this work. I am much indebted to Dr D. G. Krige and the Anglo Transvaal Consolidated In- vestment Company Limited, who gave me the opportunity to spend a considerable amount of time working on geostatistical problems, both theoretical and practical, during the time that I was in their employment. Dr Krige contributed greatly in developing my interest in studying both the theory and practice of geostatistics, always insisting that a correct balance be kept between theory and practice. I am grateful to Professor H. M. Wells and the Mining Department of the University of the Witwatersrand for inviting me to give lectures in a post- graduate course on geostatistics. The notes 1 prepared for that course became the foundation of the present work. I am also indebted to the Centre de Geostatistique of the École des Mines de Paris, where I received my first formal education in geostatistics during a summer course given by Charles Huijbregts, after many years of my lonely plodding through the published literature. Many graphs in the present volume are reproduced with the permission of the Centre de Geostatistique. The Department of Metallurgical and Mineral Engineering of the University of Wisconsin-Madison has also contributed in making this work possible, by allowing me to spend a considerable amount of time and resources in the writing, typing, and correcting of successive drafts. I am thankful to Lynn D. Kendall, who typed the entire manuscript under constant pressure.

Jan 1, 1978

By F. R. Deist, R. P. Plewman

Discussion: A. Hazell (Associate Member) and T. J. Kotze (Graduate Member): The authors must be congratulated on the development of a versatile computer programme for determining the stresses and displacements resulting from mining operations. As a design tool it will no doubt take its rightful place together with the analogue computer. Union Corporation made use of this digital computer programme whilst still in its development stage to determine the stress distributions which were causing the unexpected failure of the Marievale sub-incline shaft. Two features arising from this investigation may be of interest to members, namely: A. The solution to the problem of stabilizing a rectangular inclined shaft, which turned out to be contrary to accepted mining practice, and B. A comparison between the results obtained with the pure digital system and the analogue computer. A. The shaft is nine ft high and 20 ft wide, dipping at 9° to the horizontal and crossing the bedding planes. Fig. 1 is a plan and Fig. 2 is a section of the sub-incline shaft pillar area showing the relative positions of the shaft and reef as well as their respective dips. The deepest point in the shaft is 3 300 ft below surface and the requirement of a stress free ground surface may not be satisfied. It also means that the original gravitational stresses are low. A 900 ft wide pillar was left to protect the bottom section of the shaft, the top section being understoped years ago. Extraction of the pillar was started at the beginning of last year, mining operations being carried out in the accepted manner, starting beneath the shaft and mining outwards. The approach did, however, turn out to be the wrong one, because failure of the shaft was noticed soon afterwards. Even small movements were serious in this case due to the low clearance between the skips and the shaft supports. During October, 1968, failure between benchmarks 8 and 10 (see Fig. 1) became so excessive that hoisting speeds had to be reduced. Failure continued to occur and, by the end of March, 1969, failure had propagated up the shaft as far as benchmark 7, and down as far as benchmark 12. As this shaft had a tight hoisting schedule it was imperative that a quick solution be found to arrest the failure.

By L. Thomas, D. Muteba, L. I. Nsenga, B. Mbao, G. Longo Banza

Owing to the high ore grades in the African Copperbelt and variable acid consumption, agitated leaching is common practice and is used more widely in Africa than in other regions. Two common challenges for agitated leach–solvent extraction circuits are higher presence of colloidal silica in the pregnant leach solution and elevated levels of total suspended solids. Both can negatively affect the physical and metallurgical performance of the solvent-extraction circuit, and lead to higher processing costs or reduced copper production. Operating in organic continuity is preferred to address such challenges, but is not always possible: additional treatment options may be advantageous. For this reason, Solvay recently introduced ACORGA® CR60LT, a new chemical additive to address these concerns. Continuous addition to the pregnant leach solution improves physical performance without negatively affecting Cu transfer or cathode quality. Results and benefits from commercial utilization of ACORGA® CR60LT at different operations in the Copperbelt are reviewed

Jan 1, 2023

By K. Shame, H. H. Thiele

South Africa holds approximately 70% of the world’s total chrome reserves. Chromium is an important raw material for the production of stainless steel and ferrochrome alloys. Over the years, China’s ferrochrome market has been dependent on chrome ore imports from South Africa. In 2018, China imported about 75% of its chrome ore from South Africa. With the low platinum price and the rising demand for stainless steel, a growing demand to evaluate new beneficiation technologies for fine chromite was identified. Gravity separation of fine chromite (<75 μm) is inefficient, due to the limitations of the technology to upgrade fine particle size distributions. Potential for the recovery of chromite, specifically fines (<75μm), lost to UG2 PGM flotation tails, but also from MG and LG6 spiral circuit tailings exist. Flotation of podiform chromite ores from India and Kazhkhstan is successful in generating saleable product grade, following acid or alkaline flotation routes. Application to South African stratiform chromite is being evaluated, with the emphasis on evaluating reagent type, optimising dosages and the effect of pH in optimising flotation performance. Flotation can unlock additional value from chromite tailings material. The effect of ore characteristics such as gangue mineralogy, particle size distribution and headgrade are reported. The performance in terms of product quality and yield are evaluated and compared. The impact of this paper will not only prolong life of mine and increase revenue but will also alleviate environmental burdens associated with tailings dams. Keywords: Chromite, flotation, fine material, performance optimisation

Jan 1, 2020

By P. J. Petit

Financial evaluation is necessary to investigate the viability of implementing and/or utilising new technology in mining projects. It establishes a techno-economic base for decision-making and justifies capital expenditure. This paper aims to present a monetary appraisal of the electric rock drilling system in a typical feasibility project, whose purpose is to increase the production rate. The in situ environment is a platinum orebody, and the stoping operations occur in UG2 reef. The results are a function of production requirements, technical parameters and financial outlay of the drills. The costs involved in implementing and operating electric rock drills are assessed to the current method of drilling, namely the compressed air operation. A comparison of the electric and pneumatic rock drills in terms of financial outlays for drilling and service requirements, peripheral equipping and training is discussed. Other factors that affect the business case are technical advantages, safety and risk management and the environmental objective of the company.

Jan 1, 2006

By G. A. Wiebols, N. G. W. Cook, N. C. Joughin

Discussion R. E. Rarnes (Member): The original concepts and the pioneering work now brought to the practical test stage by the Mining Research Laboratory team deserve our highest praise. The authors of this comprehensive paper rightly stress the urgency of establishing the extent to which the apparent potential can profitably be realised in practice. It is to be hoped that adequate funds will be made available by individual mining companies, the Chamber of Mines and manufacturers to attract the necessary staff and maintain the high rate of achievement of the last two years. From the Seventy-Eighth Annual Report of the Chamber of Mines and its members we see that, in 1967, with a Working Revenue of R759.8 million from gold and R54.6 million pit mouth coal sales and with profits from gold and uranium and pyrite of R307.9 million, only R1.9 million was spent by the Chamber on all forms of Research. It is considered unlikely that the associated mining companies and manufacturers exceeded this investment expenditure. Assuming a total of R4 million spent by the industry on Research and Development, this is less than half of 1 per cent of sales of gold and coal. This percentage, so low in comparison to North America and Europe, is no worse than that of Exploration expenditure which, in 1967, with South Africa&apos;s total mineral production of R1,287 million, was estimated to have been R6 million (Pretorius 1968). In a primary industry with ever present depletion of ore deposits and with cost escalation, expenditure on Exploration and on Research and Development is not a risky luxury but a tactical obligation. The potential rate of return on research expenditure into rock breaking is high. Stores consumed by gold and coal mines, members of the Chamber of Mines, totalled R316.2 million in 1967. Except for purchased power costing R42.2 million the highest cost group was explosives, drills and drill steel totalling R33.8 million or 10.7 per cent of the total stores consumed. In the paper under discussion it is claimed that the low &apos;effective stoping width&apos; should greatly reduce the likelihood of rock falls or rock bursts to the extent that permanent support can be dispensed with. Insofar as this narrow cut is only 12 in. in advance of the working area which, with a 10 in. channel, is unlikely to be much reduced in width from that achieved by current methods, this claim is not readily understandable. Were it to have been based upon the regional support gained from packed waste it would have been more acceptable. Pre-developed stope drives may give serious trouble at depth and for this reason it is questioned whether a stoping area can avoid periodic sub-development blasting-the spoil and fumes from which will interfere with the rock flow and continuous mining of the rock-cutter. If, in the mining method proposed by the authors, stope drives are cut as small as possible (6 ft by 6 ft) then 25 per cent of the total tons handled (excluding resued waste) and 5 per cent of the gold will be blasted conventionally in the stope. At this stage one cannot envisage tunnelling machines economically or practically capable of such work. The various methods described by the authors and subsequent contributors for breaking waste are most interesting. It was noted that the &apos;bull wedge&apos; and &apos;explosives&apos; in Fig. 1 of the paper were no further from the ideal point &apos;A&apos; than was &apos;cutting&apos;. The writer considers that the bold and imaginative steps taken by the Mining Research Laboratory Team, the mining companies and the manufacturers concerned will eventually lead to a successful rock cutting machine with universal application largely independent of rock type. This may take many years. In the meantime other methods of improving productivity of saleable metal by rock breaking teams should be investigated even if such methods have local applications only. In 1955 the writer conducted tests with a wire saw similar to those used in quarries in the Northern Transvaal and elsewhere. Jeppestown shale, the immediate footwall of much of the East Rand gold field, was cut at the rate of 6 in. per hour using sand, water and a special endless rope driven by a low h.p. motor. A hypothesis on its application was submitted to the Office of the Government Mining Engineer in 1955 and to other mining institutions in 1966 after the writer returned to South Africa. By inference, rope sawing was classed as less promising than other methods tested in the Orange Free State Goldfields (Parker 1969). With highly resilicified hanging and footwall quartzites this was not surprising and confirmed the writers findings when testing hanging wall quartzite from the East Rand in 1955. The relatively uniform conditions, the low strength, hardness, and silica content of the Merensky Reef platinum deposits (Gray and von Bardeleben 1969) and in particular, the existence of overlying Merensky pyroxenite (Cousins 1964) make this and the East Rand attractive areas for larger scale testing of wire saws. It is envisaged that in suitable rock types the 5/8 in. slot would be advanced down dip or down a minor dip. In undisturbed areas &apos;faces&apos; of up to 200 ft in length could be cut several feet in advance of breaking which could then consist of light blasting to the second free face or some of the methods now being tested for breaking waste in rock-cutting operations. A wire saw is an inexpensive and simple machine which, in some areas, could make significant and early gains in rock breaking efficiency as well as in ground and stoping width control.

Jan 5, 1968

By J. van der Walt, A. Whillier

Reference is made to the approach to mine cooling in which the service water is used as one of the means of distributing refrigeration, and attention is drawn to various engineering disciplines or functions necessary for effective distribution and reticulation of cold water from refrigeration plant. The demand for service water is intermittent, the peak flow-rates being typically two to three times the average flowrate. The refrigeration plant, on the other hand, must preferably be operated steadily throughout the day and night, with the result that a large storage dam for cold water must be incorporated into each system in order to even out the surge in demand for water. These dams should be operated as constant-temperature, variable-volume reservoirs. The conventional cascade system involving dams on each level is not the best for sending water down mines, and schemes are described that avoid the need for such dams. Reference is made to various tests that were carried out, and to several large systems that were installed. Management and organizational problems that could arise as a result of new technological developments in mine cooling are referred to, and cost figures are quoted to indicate the large potential savings, In addition to the improved environmental conditions, that can be achieved through the use of integrated water systems.

Jan 1, 1979

For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984. New President On 29th March, 1985, Mr B.C. (Bertie) Oberholzer, Manager of East Driefontein Gold Mine, was elected President of the Association of Mine Managers of South Africa for the ensuing year. Bullion from old film A pollution-free chemical method of producing silver that is 99 per cent pure-and therefore of bullion quality-from scrap photographic film and paper has been developed by a British company.

Jan 1, 1985

By A. J. Dickson, A. M. Starfield

This paper reviews the progress made to date in the development of computer models of heat and moisture transfer from rock surfaces to the ventilating air in deep-level mines. The application of these programs to ventilation planning and design is discussed.

Jan 1, 2014

By C. van der Merwe, R. Lumbule, J. Kgomo

"The mining industry in the Democratic Republic of Congo has seen a significant expansion in copper and cobalt production in recent years. The greater proportion of this expansion has arisen through processing of oxide ores. The design of metallurgical processes for these oxide ores is based on the conventional equipment and layout for processing of sulphide ores, and comprises milling followed by leaching, solvent extraction, and electrowinning. The physical characteristics of the oxide ores, however, provide the process design engineer with an opportunity to examine critically the principles on which equipment selection is based and to design processes better suited to these ores. In 2015, ERG Africa began a project to expand the leaching capacity of the Luita hydrometallurgical facility. A number of innovative changes to the conventional process design were included in the modified flow sheet, which were validated when the project reached design throughput in November 2017. Of these changes, the most novel presented an alternative approach to mitigate the impact of colloidal silica on the operation of the solvent extraction plant. Introduction ERG Africa operates the Luita hydrometallurgical facility located at Kakanda in the Democratic Republic of Congo (DRC), treating malachite and heterogenite minerals to recover copper as electrowon cathode and cobalt as a hydroxide precipitate. The process was originally conceived as a heap leach operation followed by direct electrowinning of copper, with solvent extraction (SX) and electrowinning (EW) of cobalt. In preparing the sized ore for the heap leach operations, the undersized ore fraction at a P80 of 625 µm was discharged to a fines storage facility for later processing. This fraction carried with it approximately 30% of the copper contained in the run-of-mine (ROM) ore feed, and an equivalent proportion of cobalt.In a subsequent development, the cobalt SX section was converted to a copper SX facility, the leached cobalt being recovered from a bleed stream from the copper heap leach circuit. The operating cost for the process as then installed placed this facility well in the fourth quartile of the industry cost curve. The initial Luita operation was established in 2010 at a time when metal prices were above long-term averages (copper above US$3.00 per pound; cobalt above US$20.00 per pound), and the drop in prices in 2015/2016 presented a major challenge. The London Metal Exchange (LME) copper price dropped below US$2.00 per pound, with cobalt dropping below US$10.00 per pound in Q1 2016. This set in motion a range of improvement initiatives for the Luita operation. Central to this was the installation of a tank leach circuit to process the discarded fines and a modified SX circuit to manage colloidal silica. The revised Luita circuit reached design capacity in November 2017 and has proven to be well suited to processing of the oxide ore feed. This process design challenges the boundaries of conventional thinking in the areas of leaching, solid/liquid separation, solution management, impurity management, and metal recovery, and is the subject of this paper."

Nov 1, 2018

By R. G. Votteler, A. C. Brent

"The first in this series of two papers, on the potential of renewable electricity sources for mining operations in South Africa, investigated the internal structure of mining corporations to evaluate feasible alternative electricity sources that were identified as through earlier research. The purpose of this paper is to combine current knowledge about the external macroeconomic and the internal environments to produce a clear picture of how renewable sources of electricity could perform from the perspective of mining corporations in South Africa. The multi-attribute value theory (MAVT) approach was adapted to structure the research and results. The model was fed with real-time data provided from five different energy companies and four mining corporations operating in South Africa. The results show that the performance of hybrid versions of the currently used electricity sources (diesel generators and Eskom grid connection) with solar PV and onshore wind is favourable compared with the current sources alone. The advantage of diesel generators is significantly greater than that of the Eskom grid connection. By combining the macroeconomic influences with the MAVT results, hybrid solar PV versions are identified as having the greatest potential. In second place are hybrid wind solutions, which have the shortcoming that good wind conditions occur only in coastal regions where there are fewer mining activities. Geothermal hybrid versions are the least favourable owing to the lack of service infrastructure and high initial investment costs.IntroductionRecent developments in the macroeconomic environment necessitate an investigation of the internal structure of mining corporations to evaluate possible alternative electricitygenerating sources (Roehrl and Riahi, 2000). To be able to combine current knowledge of macroeconomic factors and the internal structure of mining corporations, the research process is presented in two papers. The first paper (Votteler and Brent, 2016) investigated the internal structure and argued that a strategic tool should be used to evaluate electricity sources from the perspective of mining corporations. The multi-criteria decision analysis (MCDA) approach was selected as the most appropriate strategic tool. Based on a literature review of previous similar MCDA approaches in energy planning, it was concluded that no adaptation of MCDA methods could be found from a corporate, mining, or South African perspective. Finally, the paper investigated the internal evaluation structure in collaboration with mining corporations, by identifying the criteria they use to evaluate electricity sources."

Jan 1, 2017