Search Documents

By Ron Merkel, A. Mayton

Operators of underground mobile equipment, particularly shuttle cars, are often exposed to significant levels of whole-body vibration (WBV) and shock. The human factors group at the NIOSH-Pittsburg Research Center has investigated the use of viscoelastic foam to reduce shock for the equipment operator and improve seats on mine shuttle cars.

By M. E. Poad, M. M. McDonald, J. C. Johnson, W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor shaft displacement. Results of a recalibrated two-dimensional model (UTAH2)confirmed the premining stability evaluation. However, after mining began, concern developed because of cracks and other signs of ground motion that appeared at considerable distances from the area of active pillar mining. An intense three-dimensional modeling effort using the computer modeling program UTAH3 was initiated. The results again showed the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternate pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought on the basis of two-dimensional analyses. This report focuses on startup and implementation of the three-dimensional model, calibration of the three-dimensional model, and application of the model to shaft pillar mining.

Jan 1, 1996

By Wilbert J. Huff

For the past 8 years the technical studies conducted by. the Explo- sives Division of this Bureau have been summarized in a series of annual reports.3 This report deals with activities from July 1, 1942, to June 30; 1943. Specific problems have been in immediate charge of section or unit leaders, to whom credit is given.

Feb 1, 1944

By E. J. Gleim

"Information gathered during recent months by field men of the U. S. Bureau of Mines shows that in one State alone there have been 71 fatalities from electrical causes during the last 51/2 years, of which 55 were from contact with mine trolley wires operated at 250 volts or less, direct current. The 1928 law relating to the guarding of trolley wires in the-mines of this particular State reads: ""All trolley wires carrying a voltage of class 2 must be properly shielded except where the same are at least 61/2 feet above top of rail."" Class 2 voltage is defined as being ""between 300 volts and 600 volts direct current, or 240 volts and 480 volts alternating current."" From this it may be inferred that no guards are required, for 250-volt trolley wires, and the natural conclusion to be drawn is that the lack of guards or shields must be held responsible for these fatalities. To prevent fatalities from this source, it has been advocated that every foot of trolley wire in mines should be guarded. While some such drastic step may appear to be amply justified, a closer examination of the records shows that lack of guards is not entirely responsible but rather that carelessness and neglect in the observance of certain well-established simple rules concerning installation and location of trolley wires must also bear a share in the responsibility. In -other words, if trolley wire is installed carelessly and its maintenance neglected, failure may be expected of any guards that have been put up.There are a-number of factors affecting safety as related to trolley wires in mines, among which the following may be enumerated.1. Installation relative to track and passageways.2. Guarding.3. Maintenance.4. Discipline.Acknowledgment is made to D. Harrington and K. L. Marshall of the safety division of the bureau for assistance given in securing data on cost of installing guards for trolley wires.The statement that fatalities should not be charged in every case to lack of guards is supported by the following example: A man operating a locomotive was electrocuted when the trolley wheel jumped the 250-volt trolley wire and allowed it to sag against his shoulder. He was sitting in the regular place provided in the locomotive, but the wire was 11 inches inside of the rail and only 39 inches above it where the wire touched him, or 11 inches from the roof at a distance of 12 feet from the nearest hanger. The accident occurred between two hangers 44 feet apart, and the trolley wire was inside the rail over the entire distance, being 2 inches inside at one hanger and 10 inches inside at the other hanger. A bolt in the roof indicated that there had been a hanger at one time between the two on the 44-foot span.This example is a violation of good practice in the installation and maintenance of trolley wire. In the first place the wire should have been outside instead of inside the rail. In the second place there should have been at least one intermediate hanger so that the span would not be so great and the sag would be reduced. Furthermore, it is possible that the wire was not taut enough even when the intermediate hanger was in place.To provide a degree of safety for men in the mines certain coal-mining States, recognizing the need, have enacted laws to regulate the installation of trolley wires. These limit the distance that the wire must be kept outside and above the rail. Thus, the 1927 mining laws of Ohio specify that:"

Apr 1, 1932

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

To improve electrical safety and lengthen light bulb life on trolley haulageways. Approach A resistor inserted in series with each pair of light bulbs, decreases the voltage applied to the bulbs and eliminates heavy arcing when voltages rise. How It Works Under certain conditions, incandescent light bulbs connected directly to a 300-volt d-c trolley wire can be a hazard, particularly during weekends when electrical equipment is nut in use. When little electrical power is being used, the voltage (on the trolley lines and at the substation) can rise to a value which will destroy the bulb filament, cause arcing, and damage the bulb holder. In one coal mine where light bulbs in certain locations fre¬quently failed, the problem was overcome by inserting a 100-ohm, 50-watt resistor in series with each pair of light bulbs. The light bulbs are rated at 300-volts and 100-watts. Figure 1 shows the light bulbs and resistor circuit. This resistance was added in order to reduce the current through a short circuited bulb holder, from several hundred amperes to a much safer value of 3 amperes. However, the resistor in series with each pair of light bulbs, also reduces the voltage across the lighted bulbs to approximately 240 volts during periods when the trolley line voltage is up to 300 volts. With this arrangement, no light bulb failures occurred over a 6-month period. The resulting light reduction has not been objectionable.

Jan 1, 1976

By Fred N. Kissell, Jay F. Colinet

The two major lung diseases of miners are "blacklung" and silicosis. Blacklung, or pneumoconiosis, was first recognized as a disease of British coal miners in the 1600s. However, investigations into the cause of blacklung disease did not begin until the 1900s. The causative agent of pneumoconiosis in coal miners was thought to be silica until studies in the United Kingdom provided evidence that expo- sure to coal dust containing minimal silica could also cause pneumoconiosis. In the Federal Coal Mine Health and Safety Act of 1969, coal workers pneumoconiosis (CWP) was defined as "a chronic dust disease of the lung arising out of employment in an underground coal mine." Diagnosis of CWP is generally based on chest x-ray findings and a patient's history of working in coal mines, usually for 10 or more years. In its early stages, CWP is called "simple CWP." Miners with simple CWP are at increased risk of developing an advanced stage of the disease, called "progressive massive fibrosis" pMF) or "complicated CWP." PMF (complicated CWP) is associated with significant decreases in lung function and oxygen- diffusing capacity. PMF is also associated with breathlessness, chronic bronchitis, recurrent chest illness, and episodes of heart failure. Coal miners with silicotic lesions or PMF have an increased risk of tuberculosis and other mycobacterial infections. PMF may progress even in the absence of further dust exposure. This disease is also associated with increased mortality (National Institute of Occupational Safety and Health [NIOSH] 1995). The most recent study to determine the prevalence of CWP in coal workers was in the mid- 1990s. The average prevalence of CWP was 2.8%, but for those with 30 or more years in the industry it was 14%. For the 10-year period from 1987 to 1996, 18,245 deaths were attributed to CWP. The most frequently recorded occupation on the death certificate (70%) was mining machine operator (NIOSH 1999). Silicosis may develop when inhaled respirable crystalline silica (quartz) is deposited in the lungs. The clinical diagnosis of silicosis is based on (1) recognition by the physician that the level of silica exposure is adequate to cause the disease, (2) the presence of chest radiographic abnormalities consistent with silicosis, and (3) the absence of other illnesses (e.g., tuberculosis or pulmonary fungal infection) that may mimic silicosis. The radiographic patterns are often the same for CWP and silicosis; thus, these diseases are sometimes distinguishable only by work history or pathological examination. Chronic silicosis commonly involves 15 or more years of exposure to silica. The characteristic microscopic feature is the silicotic nodule. Chronic silicosis is often asymptomatic and may manifest itself as a radiographic abnormality with small, rounded opacities of less than 10 mm in diameter, predominantly in the upper lobes. Lung function may be normal or show mild restriction. Chronic silicosis is also associated with a predisposition to tuberculosis and other mycobacterial infections and with progression to complicated silicosis.

Acid pollution from abandoned mines causes serious contamination of major streams in coal mining areas. In Pennsylvania alone it is estimated that 3000 miles of streams are devoid of fish and plant life because of coal mine effluent.1 The pollution arises because water and oxygen react with iron sulfide in the mine cavity to produce sulfuric acid and iron sulfate, which later find their way back into surface streams. Two general approaches to the problem are possible: (1) prevent the acid-forming reaction from taking place, (2) treat the acid mine water after it is formed so that it will not be harmful to the ecology when discharged into streams and other surface waters. The work described in this report belongs in the first category - it was based on the assumption that acid formation in the mine cavity can be prevented by keeping water (one of the reactants) out of the mine. This was to be accomplished by-forming a waterproof seal over the mine cavity which would prevent the seepage of surface water into the mine. It was planned to form such a seal at or near the surface of the ground by applying latex to the soil. Ideally a dilute latex would be applied to the soil and would penetrate to a depth of two to three feet below the surface where it would be coagulated by reacting with a constituent of the soil or by other means., A seal below the surface of the soil would have several advantages over a surface seal - it would not be subject to destruction by traffic, frost or vegetation and, more important, it would allow the use of the top soil for many agricultural purposes. A preliminary feasibility experiment was performed prior to application for the present grant. It showed that it was indeed possible to form a sub-surface seal by means of latex. A core of soil was obtained locally (Wayne, N. J.) by driving a 6.5 cm inside diameter steel pipe about 100 cm long into subsoil for a distance of 71 cm. The soil was retained within the pipe for this experiment. A part of the free space above the soil in the pipe was charged with water, and the seepage rate of the soil after it had become saturated was 15 ml/min under a total head (wet soil plus supernatant column of water) of 92 cm. After the supernatant water had drained completely, 100 ml of 5% rubber latex was added and allowed to seep into the soil. This was followed by additional water and the seepage rate was found to be 2 ml/min under the same head. This seepage rate remained unchanged when remeasured on the following day. Since there was no visible evidence of the latex in the collected drain water it is presumed to have been retained by the soil.

Jan 1, 1972

By R. V. Ramani, A. S. C. Owili-eger

The rapid depletion of shallower coal reserves dictate that mining in the future will be deeper and more complex with more difficult natural conditions. Consequently, an increase in methane emission is expected. It is becoming evident that more accurate predictions and better planning are necessary to design efficient methane drainage systems. This objective can be achieved by the utilization of the knowledge of the physics of gas flow through coal seams and rock strata and by the application of digital computers in the solution of methane flow problems. Although the methane emission models described here have not been adequately applied to existing field operations, good agreement between actual field measurements reported in literature and the simulation results indicates the potential of these models for initial flow quantity approximations and ventilation planning. This report has, therefore, introduced to the mine operator yet another application of computers as a planning tool. AREAS FOR FURTHER RESEARCH The study reported here is by no means complete. Extensive research efforts should be directed to the following areas: (a) Better understanding of the physics of gas flow through porous media which exhibit fracture permeability. (b) Determination of field parameters which control gas migration. (c) Investigation of the effects of the rate of penetration on the emission rate and fracture propagation.

Jan 1, 1974

By N. W. Lord

This volume contains the descriptions of the samples whose analy- ses are published in the preceding volume, Part I of this bulletin. The descriptions have been compiled from the notebooks of the per- sons who collected the samples, have been condensed from accounts given in published reports of the United States Geological Survey, or have been furnished by the collectors themselves. Inasmuch as the descriptions represent the work of many persons during a period of six years, and inasmuch as they were recorded under widely differing conditions, they necessarily vary in fullness of detail. The descriptions are published for two purposes: (1) To prosent such information regarding the character of the coal, the impurities in the beds sampled, and the nature of the roof and the floor of the beds as has a definite bearing on the significance of the analyses of the samples, and (2) to give any supplementary details such as the capacity or the output of a mine, the method of mining and prepar- ing the coal, and the chief uses to which it is put, that may be of assistance to Government engineers or purchasing agents, and to other persons, in preparing specifications and awarding contracts for fuel.

Jan 1, 1913

By Christopher Mark

Since it was first introduced, the Coal Mine Roof Rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground control problem. Extended cuts (cuts greater than 6 m (20 ft) in length) are commonly used with remote control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof fall accidents. When extended cuts are attempted in weak roof, the roof may collapse before it can be bolted, causing hazardous conditions. Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended cut experience were collected at 36 mines in 7 states. It was found that when the CMRR was greater than 55, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken. Between 38 and 55, extended cuts were feasible sometimes but not others. The data also shows that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

By Michael J. Sapko, Gregory M. Green, Harry C. Verakis, Kenneth L. Cashdollar

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted a joint survey to determine the range of coal particle sizes found in dust samples collected from intake airways of U.S. coal mines. The last comprehensive survey of this type was performed in the 1920’s. The size of the coal dust is relevant to the amount of rock dust required to inert the coal dust, with more rock dust needed to inert finer sizes of coal dust. Dust samples were collected by MSHA inspectors from several mines in each of MSHA’s ten bituminous Coal Mine Health and Safety Districts. Samples were normally collected in several intakes at each mine. The laboratory analysis procedures included acid leaching of the sample to remove the limestone rock dust, sonic sieving to determine the dust size, and low temperature ashing of the sieved fractions to correct for any remaining incombustible matter. The results indicate that particle sizes of mine coal dust in intake airways are finer than those measured in the 1920’s. The significance of these finer coal dust sizes is discussed relevant to the amount of rock dust required to prevent coal dust explosions.

Coal-bearing beds underlie 23,000 square miles, about one third of Missouri's total area. Twelve out of more than twenty named coal seams have been or are being commercially mined. The remainder are too thin for commercial production. The coal is high volatile bituminous, with reserves estimated to be six billion tons, 1.24percent of U.S. coal reserves. Coal-bearing strata are generally thin seams which can be up to five feet thick. Typically, mined seams are about 28 inches thick. Coal deposits were first mined in Missouri in the 1840s, with the coal used primarily for domestic heating and blacksmithing. Production increased with the introduction of steamboats on the Mississippi. Coal production in 19 17 was six million tons. Production has steadily declined from a high of nearly seven million tons in 1984 to 2.3 million tons in 1991. Declining production is the result of several factors, including competition from other energy sources and the high sulfur content of Missouri coal. Today, coal-fired electric generating plants are the biggest consumers of Missouri coal. The Missouri regulatory program was conditionally approved November 21,1980, and fully approved January 17,1983. Its Abandoned Mine Land program was approved January 29, 1982.

Jan 1, 1992

By Edward McHugh, Jami M. Girard, Stanley M. Miller

A computer analysis of bench stability has been developed to account for multiple occurrences of potential slope-failure modes in discontinuous rock masses. Bench-scale plane shears and tetrahedral wedges are simulated and stochastically analyzed to estimate the probability of retaining specified catch-bench widths. This geotechnical information is useful in designing bench configurations to improve pit-slope stability and help alleviate rockfall hazards.

By L. A. SCHOLL, J. K. CLEMENT

Among the problems investigated by the Bureau of Mines the coal- dust problem has received much attention. Several of the bureau's publications deal specifically with the subject. Bulletin 20° contains an account of preliminary experiments of the bureau to determine the explosibility of coal dusts as well as a review of pertinent literature. Bulletin 50 is a report of a laboratory study of the inflammability of coal dust. The first series of coal-dust explosion tests in the bureau's experimental mine at Bruceton, Pa., is described in Bulletin 56, and Technical Paper 56 presents notes on the prevention of dust and gas explosions in coal mines, and Technical Paper 84 discusses the causes of such explosions and describes methods and apparatus devised by engineers of the bureau for preventing and checking them. The present paper is a report of a detailed study of the bituminous dusts of Illinois mines, and is a part of the investigations conducted by the bureau in cooperation with the Illinois State Geological Survey and the department of mining engineering of the University of Illinois./ It is well known that bituminous coals like those found in Illinois yield dusts that may give rise to explosions of great violence. In order that proper methods might be devised for preventing dust explosions in Illinois mines it was considered desirable to obtain accu- rate information on the quantity and character of these dusts. Ex- periments and tests of dust explosions in an experimental mine as well as in a large steel gallery comparable in area of cross section to mine entries have been made by the Bureau of Mines. Similar experi- ments have been made in Austria, England, France, and Germany. Experiments under conditions similar to those of actual mining prac- tice are obviously more conclusive than tests made in a laboratory. On account, however, of the expense, time, and quantity of dust re- quired, it is not practicable to conduct large-scale tests in studying a large number of dusts and recourse must be had to laboratory apparatus and methods. Laboratory,devices for the study of coal-dust explosions have been devised by a number of investigators. Most of these were intended for qualitative tests only. Quantitative methods have been devised by investigators of the English and French mining-experiment stations." In the experiments described in this report, laboratory tests of inflam- mability were made with an apparatus devised by Dr. J. C. W. Frazer, formerly a chemist of the Bureau of Mines. Laboratory tests of inflammability have been made on more than 500 samples of dust from 100 representative Illinois mines. As a result of these tests it may be stated that: 1. The coals of Illinois when ground fine enough yield highly inflam- mable dusts which when suspended in air may give rise to violent explosions. 2. In the majority of the mines of the State the dusts adhering to the ribs are inflammable. In about one-fourth of the mines the quantity of rib dusts present in the entries is sufficient to form an explosive mixture with air. 3. Most of the road dusts are inflammable when ground to a suffi- cient degree of fineness.

Jan 1, 1916

By A. T. Iannacchione

Designing coal pillars to provide resistance against overburden and gob loads has long been an aim of rock mechanics engineers. This requirement has become more imperative as greater overburdens are encountered and when mining in stiff coal-bearing strata. Current design procedures rely on theories of coal pillar behavior that take into consideration a common hypothesis. This hypothesis states that the elastic core is surrounded by an inelastic yield zone. The distribution of stress at low-to-moderate pillar loads has been effectively defined by this hypothesis. However, it suffers greatly when applied to large width-to-height (w/h >lo) coal pillars under considerable overburden (>500 m) . In these situations, the hypothesis says the elastic core can achieve unrealistic stress states giving the pillars extremely high calculated strength. A growing body of field studies has shown this is not the case. It has become clear that same other mechanism must be involved. It is the purpose of this paper to discuss the importance of an interface slip mechanism between the coal- bed and the surrounding strata in controlling the extent and pattern of stresses and deformations in a coal pillar.

By Chas F. Jackson

 The annual reports of the supervising engineers of the several sections of the Mining Division are assembled herein and comprise the annual report of the division. During the year under review the work was oriented entirely to the war program by applying apparatus and technique previously developed in research directly to war problems, as well as by intensified search for and exploration of deposits of minerals necessary in the war.

Oct 1, 1942

By T. E. Marshall, D. R. Dolinar, C. S. Cornpton, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

The U.S., Australian, and United Kingdom coal and the Canadian hard rock mining industries have long recognized the significance of high horizontal stresses as a factor affecting the stability of roof and rib conditions in underground mines. Recently, a growing segment of the U.S. underground stone mining industry has also begun to recognize that horizontal stresses occur in some of its more than 90 mines. Considering the typically high strength and massive nature of limestone, this fact is a revelation in itself. High horizontal stresses produce extensive and sudden rock failures and, in some cases, resulted in injuries to mine workers. Through the years diverse control strategies have been proposed and experimented with. Reorientation of mine entries to reduce stress concentrations have proven successful and are widely accepted in practice. Other solutions, like rock reinforcement, are poorly understood and less accepted in practice. It is the purpose of this National Institute for Occupational Safety and Health (NIOSH) study to develop a better fundamental understanding of these ground control strategies under high horizontal stress conditions through a series of field and laboratory studies. To this end a design technique is presented which provides stone miners with a method for making stability assessments. The consequences of widening rooms, changing geology and horizontal stresses, and different rock bolts on roof beam failures are discussed.

By Arno C. Fieldner

In connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the character of the coal and the value of the fuel in the public lands, many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The systematic collection and analysis of coal samples in connection with investigations of fuels was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition, and was under the direction of the United States Geo- logical Survey for six years. Descriptions of the coal samples col- lected in connection with these investigations between the beginning of this work, July 1, 1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines, July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22. The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1911 to 1913. In order that the material in this bulletin may be used to supplement that presented in Bulletin 22, the same plan of geographical classification has been fol- lowed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1914

By N. H. Snyder

Coal analyses help to describe the character of coal as it lies in the ground of as it may he delivered to the user Analyses of samples of coal collected from the face of the bed in mines are plentiful, but available analyses of delivered coal are relatively few, and there is a distinct difference between "mine samples" and "delivered samples.” Mine samples are collected actor drag to a standard method. 13 The sampler cuts a channel. 2 by 6 or 3 by 4 inches from roof to, floor in the face of the bed, and excludes from the sample all partings more than 3/8 inch thick, and any lenses or concretions of sulphur or other impurities more than 2 inches in maximum diameter and 2 inch thick. Analyses of mine samples form a permanent and scientific record of the coal bed at the point sampled, they ale important in determining the character of the coal in any given mine or district These analyses, when the samples are taken by a standard method, are valuable to the operator When compared with analyses of delivered coal they show him whether his mine is being worked efficiently or whether the coal is being properly prepared, which involves the ques¬tion ii Nether he has suitable mechanical appliances for separating the impurities sties. In the purchase of coal, mine samples may serve as a sufficient guide for the experienced buyer who has knowledge of the impurities in the bed, and the degree to which these are eliminated in mining and preparing the coal To the average purchaser, however, unacquainted with these details, dependence on mine samples may be misleading The quality of coal indicated by the base samples call rarely, if ever, be attained in the delivered coal Certain impurities that are eliminated from the formally prepared mine sample may not be eliminated by the miner Some of the roof and floor may also be included if these are soft or flaky When coal prices are high and competition is lessened it is easy for the miner and the management to lower the standards of preparation, and a return to rigid stand¬ards is always difficult. In sampling delivered coal the Bureau of Mines follows a definite procedure. 14 A sample of not leas than 1000 pounds is systematically

Jan 1, 1928