Search Documents

By G. A. Burrell, G. W. Jones

As a part of the work which the Bureau of Mines carried out in 1916 and 1917 pertaining to the compressibility of natural gas , it became necessary to de termine the pressure -volume relations of several of the paraffin hydrocarbons of which natural gas is composed . Results of the work on natural gas were published in Technical papers 131 (Burrell , G.A. , and Robertson , I.W. , The compressibility of natural gas to high pressure , Bureau of Mines Tech . Paper 131 , 1916 , 12 pp. ) and 158 (Burrell , G.A. , and Robertson , I.W. , Compressibility of natural gas and its constituents with analyses of natural gas from 31 cities in the United States , Bureau of Mines Tech . Paper 158 , 1917 , 12 pp . ) , and curves were given of pressure volume deviations of the gases , methane , ethane , propane , and carbon dioxide at high pressures . original experimental data on these gases , however , were not published . The In view of many inquiries which the Bureau has received with reference to the original data on the se gases , and the importance of the pressure -volume relations from which it is possible to calculate the deviation of any natural gas who se composition is known , the original data as determined by Burrell and Robertson are pre sented below .

Aug 1, 1921

By M. M. Jones

A procedure for the spectrophotometric determination of uranium has been developed in support of minerals research being conducted by the Bureau of Mines. Uranium is separated from the sample by tributylphosphate extraction from acid solution containing added aluminum nitrate and (ethylene dinitrilo)-tetraacetic acid solutions. The colored uranium-dibenzoy1methane complex is developed in the organic phase by adding an ethanol solution of dibenzoylmethane buffered with triethanolamine. Absorbance is measured at 410 nanometers, and the response is linear up to at least 100 micrograms U30S in the aqueous aliquot taken for analysis. Aliquots containing as little as 8 micrograms U30S may be analyzed with relative errors no greater than ±5 percent. For aliquots containing at least 35 micrograms U308, relative standard deviation at the 95-percent confidence level is about ±2.2 percent. Appropriate procedures are given for analyzing a wide variety of samples.

Jan 1, 1980

By R. A. Keaens, L. C. IlsLey

For the purpose of this paper a junction box is defined as " a fused switch, inclosed in an explosion-proof compartment, provided with a ready means of connecting or disconnecting a trailing cable without exterior arcing." Junction boxes are intended for use 'at the end of trailing cables and are usually placed outby the last open break through in a coal mine. Where it is not safe to supply current through nips or a trolley, junction boxes suitably spaced along an entry permit tramming and movement of machines with safety, although not with any considerable speed. Junction boxes serve a threefold purpose: (1) They prevent dangerous arcing at the outby end of trailing cables; (2) they afford a safe, practical means of fusing or otherwise protecting the trailing cable; and (3) they provide an efficient means of transmitting power from the power circuit to the trailing cable. The first purpose is the most important from a safety standpoint. Dangerous arcing-that is, arcing capable of igniting gas-frequently takes place where trailing cab1c.s are attached to the power circuit. At either 250 or 500 volts only a very small arc is required to ignite mine gas. The usual method of connecting the trailing cable to the power circuit by cable nips or trolley taps does not make a good electrical connection; hence arcing may be expected at any time. Furthermore, junction boxes eliminate the personal hazard attendant upon the use of trolley taps by removing the possibility of accidental contact with trolley hooks or wire and the liability to injury due to manipulation of the device. In the general scheme of mine ventilation it is assumed that gas will not accumulate where junction boxes are placed, an assumption based on the normal operation of the ventilating system. In many

Jan 1, 1929

By John J. Mulligan

Ear Mountain is an isolated mountain mass that rises abruptly from the coastal plain on the northwest shore of the Seward Peninsula. Geologically it resembles the more accessible Brooks Mountain and Cape Mountain areas to the southwest, being composed of a granitic core surrounded and partly capped by metamorphosed sediments. The occurrence of lode- and placer-tin deposits in this area has been known since the early 1900's, when the Seward Peninsula region was prospected extensively for both gold and tin. The Federal Bureau of Mines investigated the tin deposits in the Ear Mountain area during the 1953 and 1954 field seasons. The objectives were to delimit the areas in which tin minerals occur, as a guide to future prospecting, and to determine the amount of tin in the known prospects. Work by the Bureau of Mines included both placer and lode sampling.

Jan 1, 1959

By William A. Hoffman

In This Chapter [MSHA regulations for coal mines MSHA regulations for metal/nonmetal mines OSHA regulations for tunnel construction Types of respirators used in mines and tunnels Filter materials and filter efficiencies Donning, seal checking, and maintenance Filter service life and Respirator information resources] In many cases, engineering controls are not adequate to achieve satisfactory dust levels, so respirators must be used. This chapter explains the Federal regulations governing the use of dust respirators in mines and tunnels and describes the most common dust respirators used. Filter materials and filter efficiencies for respirators are discussed. This chapter also gives some guide-lines for respirator use and recommends sources for more dust respirator information. Respirator effectiveness in reducing dust exposure usually exceeds the effectiveness of most engineering control methods. RESPIRATOR REGULATIONS [Different regulations govern respirator use in coal mines, metal/nonmetal mines, and tunnels under construction.] Coal mines under Mine Safety and Health Administration (MSHA) jurisdiction. Coal mine operators are required to meet dust standards using only engineering control methods. Typical engineering control methods include ventilation and water sprays. Respirators are not regarded as an engineering control method, so respirators cannot be used in lieu of engineering controls.

Jan 6, 2003

By G. E. McClelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores, wastes, and tailings. This technology has been adopted on a broad scale by the precious-metals-processing industry. This report presents information on five commercial operations that have benefited from agglomeration technology and that represent a cross section of current heap leaching practice. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1983

By Ronald D. Hill, Elmore C. Grim

The removal of overburden often exposes pyritic materials (iron disulfide). As shown in equations 1 and 2, the oxidation of this material results in the production of ferrous iron and sulfuric acid. The reaction then proceeds to form ferric hydroxide and more acid, as shown in equations 2 and 4. [ ] Consequently a low pH water is produced (pH 2-4.5). At these pH levels, the heavy metals such as iron, manganese, copper, and zinc are more soluble and enter into the solution to further pollute the water. Water of this type supports only limited water flora, such as acid-tolerant molds and algae; it will not support fish life, destroys and corrodes metal piers, culverts, barges, etc., increases the cost of water treatment for power plants and municipal water supplies, and leaves the water unacceptable for recreational uses. The amount, and rate of acid formation, and the quality of water discharged are a function of the amount and type of pyrite in the overburden and coal, time of exposure, characteristics of the overburden, and amount of available water(l). Crystalline forms of pyritic material are less subject to weathering and oxidation than amorphic forms. Since oxidation by oxygen is the primary reaction during early acid formation, the less time pyritic material is exposed to air, the less acid is formed. Thus, a positive preventative method is to cover pyritic materials as soon as possible with earth, which serves as an oxygen barrier. In terms of mining, this step is accomplished by current reclamation techniques and small open pits.

Jan 1, 1974

By Donald M. Hausen

Diamond-bit performance and cost data accumulated by the Bureau of Mines in core-drilling schists reveal significant trends of economic interest. Low-quality, small-size drill bort were the most economical. The percentage of core recovery, type and size of bit, and bit matrix are also correlated with bit performance and costs. Detailed analyses of the factors affecting diamond-bit performances and costs are assessed in the tables, graphs, and discussion.

Jan 1, 1956

By Eric E. Cather

A mineral investigation by the U.S. Bureau of Mines revealed no mines or prospects and no past or present mining claims in the Agua Tibia Wilderness Study Area (WSA). The area is underlain mainly by weakly foliated gabbro similar to rock that has hosted gem- and lithium-bearing pegmatites in the Pala district about 6 mi to the south. However, no gem- or lithium-bearing pegmatites have been discovered in the WSA. Nearby quarries in the gabbro have yielded rock for facing and dimension stone. No sand, gravel, or energy (oil, gas, coal, or geothermal) resources were identified.

Jan 1, 1984

By W. R. Reed, J. A. Organiscak

Surface mining operations use large off-road haul trucks extensively to move material at mining properties. Past research, using the United States Environmental Protection Agency’s (EPA) emissions factors for unpaved haul roads, has shown that haul trucks generate the majority of dust emissions from surface mining sites, accounting for approximately 78%-97% of total dust emissions. Observations of dust emissions from haul trucks show that if the dust emissions are uncontrolled, they can be a safety hazard by impairing the operator’s visibility. This increases the probability for haul truck accidents (See photos above). However, the greatest long-term health hazard of dust generated from hauling operations is due to inhalation of the respirable dust [median diameter <4 micrometers (µm)] and tho­racic dust, which is equivalent to the EPA’s definition of PM10 [particulate matter with a median diameter <10 µm]. Exposure to respirable dust has long been considered a health hazard at surface mining operations, especially if silica dust is present. There are two legislative acts that regulate the air quality for mining operations: the Federal Coal Mine Health and Safety Act of 1969 and the Clean Air Act of 1970. The Federal Coal Mine Health and Safety Act of 1969 established the limits for dust in the work place for health and safety pur­poses. The Clean Air Act of 1970 regulates air emissions from facilities from an envi­ronmental perspective.

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operatons at or near mines.

Jan 1, 1963

By K. R. Farley

A simplified method for the atomic absorption determination of antimony is described. Samples are dissolved in hydrobromic acid and diluted to volume with water. Solutions can be ready for analysis in about 10 minutes and are stable for at least 24 hours. The spectral line at 231 nanometers is used, and there is no effect on absorption resulting .from the presence of any concentration of HBr. Absorbance is linear with antimony concentrations up to 120 micrograms per milliliter. Sensitivity is 1.48 micrograms per milliliter per 0.0044 absorbance. Relative errors on National Bureau of Standards Standard Reference Materials were 3 percent or less, and relative standard deviations on 12 determinations of each of three flue dust samples were 4 percent or less (95-percent confidence limit).

Jan 1, 1980

By D. Harrington

The occurrence of dusts in underground workings creates many difficult and, in some instances, contradictory and conflicting problems for workers, operators, and all others interested in health and safety in mining and tunneling. Moreover, there are many misconceptions both as to the actual effect of most dusts which may be encountered in underground work and as to remedial or alleviating measures. Although the harmfulness of mine dusts to health of miners has been mentioned by man; writers in ancient times, much of our really authentic knowledge of the effect of underground dusts upon health or safety in both coal and metal mines has been pained during the past 30 or 35 years. There has been, however, a considerable amount of generalizing from some local condition or occurrence or theory rather than arriving at conclusions after extended studies and observations made not only in mines and tunnels but also in town, camps, and plants, and comprising date on as many different mining and tunneling localities, conditions, etc., as could be secured with reasonable expenditure of time or money. This paper dives sortie observations based on the writer&apos;s 30 odd years of experience in and around both coal and metal mines, including approximately 20 years? close study of dust disease with detailed surveys and reports on dust occurrence and effects in considerably more than 100 mines in probably 20 States of the Union. The observatio are those of an engineer and in many respects conflict the with "going" ideas of doctors, pathologists, and others who have written on dust disease. Were the word dust is used in this p: per in connection with respiratory disease, it refers to solid particles which float or can float in the air breathed by workers. Although these particles are usually dry, they may be wet; in general, their dimensions are so small as to be invisible to the nailed eye. Dusts in coal mines which may be involved in the initiation or extension of explosions, are generally thought to be those which are smaller than 20-mesh in size but chiefly finer than 20-mesh; coal-mine dusts which are harmful to health of workers have essentially the same general physical characteristics as other dusts, but usually consist of smaller particles.

Jan 1, 1936

By Bill M. Stewart

The Bureau of Mines conducted laboratory tests to determine the effects on the physical properties of coarse coal waste of adding large amounts of fine coal waste. Maximum laboratory dry density, optimum moisture content, shear strength, and permeability tests were conducted on samples that contained 18 to 60 pct minus No.4 (U.S. Standard sieve size) coal waste. For the nonslaky materials, maximum laboratory densities were highest and permeabilities lowest when the samples contained between 30 and 40 pct minus No.4. Shear strength increased rapidly when the proportion of minus No. 4 was increased from 20 to 40 pct, but then increased only slightly or leveled off when the minus No. 4 was increased to 60 pct. Optimum moisture content and permeability were the physical properties most affected by the addition of fines. Optimum moisture content increased as much as 3 pct, and permeabilities decreased up to three orders of magnitude. Slaky coal waste material had physical property reactions to the addition of fines substantially different from those of nonslaky material.

Jan 1, 1981

1. Alford, N.G. quantity, of timber used in soft-coal mines and how much will be needed for the future. Gives a table of estimated increase in mine timber consumption in the future. A.I.M.E. Separate. 1336-C 1924. 2 Clark, B.M. The forest and the mine. Rept. Conference of Wood-Using Industries, Harrisburg, Pennsylvania. Apr. 13-14, 1921, pp. 58-62. Describes experience of a Pennsylvania mining company in depletion of timber supply and conservation methods adopted.

Jan 1, 1925

Provide blasting-resistant, quickly reusable stoppings for large mine openings. Approach Stoppings are assembled using roof-to-bottom panels of brattice held together by Velcro seams that peel open when struck by a strong air blast. How It Works The Velcro seam is designed to open when exposed to forces lower than would normally damage the brattice. When the seams partially open, they relieve the blast air overpressure to prevent damage to the brattice panels and their anchoring devices. A stopping is returned to service by reclosing the Velcro seams. To hang a brattice panel, its top is stapled to a board, and wrapped once or twice around it. That assembly is then attached to the roof with bolts. The length of the board should be a foot less than the width of the panel to allow for the sealing seam on each side of the panel. The boards are installed end-to-end in an approximately straight line across the roof of the mine opening.

Jan 1, 1979

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972

By John R. M. Hill

The Bureau of Mines performed elastic-plastic, finite-element analyses to investigate the support performance of hydraulic backfill. A mathematical model was developed for two vertically adjacent stopes separated by a sill pillar. An exact duplicate of a working stope was not intended; however, the model did simulate a working stope to the extent that field measurements from an active stope could be used for comparative purposes. Using a predetermined mining sequence, the computer analysis simulated the mining operation as a series of incremental cut-and-fill steps. Computer results included a complete history of stope closure and pillar stresses throughout the mining sequence. With the mining sequence and rock properties held constant, three separate analyses were made using varying backfill properties. These cases included no fill,-low-to-medium-quality fill, and medium-to-high-quality fill. Results of these analyses show decreases in stope closure and pillar stresses as the backfill quality increases, thus reducing the possible occurrence of rock bursts. Predicted stresses within the backfill compare favorably with field measurements. A relationship between maximum stress normal to the stope wall and the ratio of relative fill stiffness to relative rock stiffness was also indicated.

Jan 1, 1974

By Robert J. Timko

The objective of this Bureau of Mines research work was (1) to determine how well the E. I. Du Pont de Nemours and Company P-2500 personal dust sampling pump controls the flow rate at 2 L/min and (2) to compare respirable dust mea-surements made using the P-2500 with those made using a nonpulsating sampling flow system, both using the Dorr-Oliver 10-mm nylon cyclone dust size classifier. The calibrator and the operation manual for the P-2500, supplied by the manufacturer, were also evaluated. Flow tests consisted of long-term (6-to 8-hour) flow stability tests at various backpressures, a low-flow indicator examination, flow controller response time tests and pulsation tests. Dust tests were performed using coal, silica, and Arizona road dust. No tests were performed to examine effects of temperature, barometric pressure, vibration, or mechanical shock. These pumps performed well within manufacturer specifications in all tests.

Jan 1, 1982

By Forrest T. Moyer

Injury experience in the mineral mining and processing industries during 1968 was slightly improved in the nonfatal-injury record but worse in the fatality record. The resulting frequency rate of all injuries was slightly better, whereas the injury-severity rate retrogressed appreciably from the figure for 1967. Overall operating activity, as measured by man-hours of worktime, was slightly higher in 1968. However, there were several major segments of the mineral industries in which activity was lower owing to reduced demand for mineral products and to several major work stoppages. These statistics comprise the injury and work experience of all personnel engaged in production, exploration, development, maintenance, repair, and force-account construction work, including supervisory and technical personnel, and working partners and owners at mineral-producing and mineral-processing establishments in the United States. Data concerning officeworkers are excluded except for the oil and gas industry for which such information is not separable. All injury rates and totals are calculated from data before rounding. The data for 1968 are preliminary except for the anthracite, coke, petroleum and natural gas, native asphalt, peat, and slag industries, which are final. The figures represent full coverage for all industries except oil and gas for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1970