Search Documents

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system’s design philosophy, hardware and software components, examples of installations, and a few observational results.

The Federal Mine Safety and Health Act of 1977* defines respirable dust as dust measured with a device approved by the Secretary of Labor and the Secretary of Health and Human Services [30 USC 842(e)]. The approved sampler for respirable coal mine dust is the coal mine dust personal sampler unit (CPSU) [30 CFR 74; Jacobson 1971; Jacobson and Lamonica 1969]. The CPSU is generally called the 10-mm nylon cyclone, although the 10-mm nylon cyclone is actually just one component of the CPSU. The CPSU may either be mounted on a worker (with the sampling head positioned in the breathing zone for personal exposure monitoring) or in a fixed location for area sampling [Tomb 1990]. The CPSU consists of a pump unit, a sampling head assembly, and a battery charger if rechargeable batteries are used in the pump unit [30 CFR 74.2]. The sampling head assembly contains two stages. The first stage is a 10-mm nylon cyclone, which has collection characteristics similar to an elutriator. The amount of dust penetration depends on the flow rate [Jacobson and Lamonica 1969]. The second stage is a membrane filter (vinyl, pore size 5 pm) that collects the dust passing through the cyclone. The dust collected on the membrane filter is weighed to a precision (standard deviation) of 81 pg [Parobeck et al. 1981], and the respirable dust concentration in the mine atmosphere is then determined from the mass of dust collected and the volume of air sampled [Tomb 1990].

Jan 1, 1997

By R. E. Brown

The objective of this Bureau of Mines study was a laboratory-scale evaluation of the sodium sulfate refining process for removing copper from molten ferrous scrap. Maximum copper removal is achieved in carbon-saturated melts at 1,300° C. Low carbon concentrations and higher temperatures result in a less efficient copper removal and an increased sulfur concentration in the iron. Sodium sulfate refining significantly lowers the concentration of aluminum, manganese, and silicon; however, the copper removal efficiency is adversely affected by the presence of manganese and silicon. Compared with other reagents tested, sodium sulfide-forming slags were found to be the most suitable for both copper removal and sulfur control. The sulfur content of the refined iron was higher in tests conducted in acid-type refractory crucibles. Earlier studies showed that tin, a significant metallurgical impurity, is not removed by the sulfate process. During the present investigation, results showed that chlorination, using organic solid sources of chlorine, reduced the tin concentration to acceptable levels in molten iron.

Jan 1, 1975

By L. A. Haas

The degree of reduction of various silica-graphite mixtures was studied in a batch reactor to determine optimum physical conditions for maximizing the carbothermic reduction of silica. The extent of interaction was determined for reactant mixtures in loose powder and briquet forms at pressures less than 0.01 torr and temperatures up to 1,445° C. Molar ratios were varied from 0.05 to 6.5 with maximum reaction at a ratio of about 1.5. The solid-solid reaction did not appear to involve gaseous intermediates. The extent of reaction better correlated with the number of interparticle contacts than with the true surface area of the reactants. Carbonized dextrose was a better reductant than graphite.

Jan 1, 1968

By J. P. Conway

The yielding-rock-bolt concept, as developed in South Africa, consists of a smooth-bore die or collar fitted to a standard rock bolt. Laboratory testing at the Bureau of Mines Spokane Mining Research Center under slow and fast strain rates showed that extrusion loads can be controlled by varying the configuration of the die bore and that theoretical analysis (using basically Sachs' theory of wire drawing) predicts extrusion loads of the different die-bore configurations. A derived equation, based on this research, can be used for designed die-thread combinations for any desired extrusion load. Dynamic loading resulted in slightly higher loads (15 percent) than static loading. The strain hardening effect, which increases yield and ultimate strength, was partly offset by adiabatic heating of the threads, which decreases strength.

Jan 1, 1975

By Phyllip Worley, Frank E. Chase, Christopher Mark

The Harris No. 1 Mine, located in Boone County, WV, has been longwalling the Eagle Coalbed for over 30 years. Harris has experienced numerous interactions associated with the extensive room-and-pillar and longwall mining operations which have been conducted in the overlying No. 2 Gas Coalbed. The problems have included roof falls, excessive rib sloughage, and gateroad and bleeder entry closure. A detailed evaluation of the multiple seam experiences at Harris No. 1 Mine was conducted as part of the National Institute for Occupational Safety and Health (NIOSH) nation-wide multiple seam mining case history data base. One observation from the Harris gateroad case histories was that smaller, critically loaded, upper seam pillars seemed to cause more severe ground conditions than did wider pillars. The LaModel program was used to investigate this supposition, and the results confirmed that “critical” sized pillars do transmit the highest amounts of stress to adjacent seams. In addition, the data suggest that the probability of a major multiple seam mining interaction increases when the depth of cover is 1,000 ft or greater and when the Eagle seam pillars have a Analysis of Longwall Pillar stability factor less than 1.50.

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove, grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 2 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1970

By G. G. Morgis, J. J. Forbes

"INTRODUCTION The greatly diversified and increased uses of beryllium and its con& pounds in recent years have focused attention on the health hazards incident thereto. The Bureau of Mines has a fundamental interest in safety and the elimination or reduction of health hazards in the mineral and allied industries, and it recognizes that serious hazards are inherent in the production and use of beryllium and its compounds. This circular presents a review of the literature pertaining to such health hazards but does not describe original research by Bureau personnel. Most of the bibliography has boon either quoted in part or abstracted in an effort to present information in a comprehensive and readable form.In reviewing the literature, differences of opinions wore recognized in the writings of the respective authors, but no attempt was made to evaluate such differences. This presentation was devoted strictly to reporting without editorial comment.SUMMARYAlthough beryllium was known to industry for about 150 years, its toxicity did not present any serious problems in the United States until the advent of World War II, when the increased use of this element and its compounds brought to light several toxicologic reactions occurring primarily in the lungs and skin of workers handling it. The pulmonary effects, characterized as acute pnoumonitis and chronic pulmonary granulomatosis in beryllium workers, are far more serious than the dermatological manifestations.The addition of beryllium to the list of toxic industrial metals has boon so recent that there is still some confusion in the clinical picture. Data on magnitudes of exposure likely to be responsible for the production of disease are not yet adequate. There appears to be no relation between the severity of exposure and the development of cases some of those having had severe exposure have not developed a reaction, whereas those having a slight exposure in some instances have developed a response."

Jul 1, 1950

By L. E. Schultze

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines devised a processing sequence for recovering uranium from carbonaceous ores. Uranium extractions of 97 pct were obtained by contacting the ore with a solution containing 400 grams of ferric sulfate hydrate in 200 ml water for 3 hr at boiling temperature (96° C). Uranium was recovered from the leaching solution by solvent extraction with tri-issooctyl amine. The barren ferric sulfate solution was recycled to the leaching system. The leaching process resulted in no detectable dissolution of carbonaceous material from the ore. Work on the project was terminated in 1978 because of a transfer of responsibility to the U.S. Department of Energy.

Jan 1, 1981

By C. H. Elder, Maurice Deul

Coal degasification boreholes drilled from the surface have been success - fully hydraulically stimulated to increase the flow of gas from the coal. This Bureau of Mines report describes the hydraulic stimulation procedure for a coalbed, the equipment required, and design criteria for the treatment. Three examples of stimulation treatment show from fivefold to twentyfold increases in gas production. The tests were conducted in the Pocahontas No. 3coalbed, Buchanan County, Va., the Pittsburgh coalbed, Washington County, Pa., and the Mary Lee coalbed, Jefferson County, Ala. Two sites where the coal was hydraulically stimulated and exposed by subsequent mining show no adverse effect on mining operations through the treated zones. The induced vertical partings were confined to the coalbed and did not in any way affect either roof or floor rock.

Jan 1, 1975

By Alan R. Buehler

The Bureau of Mines conducted a mineral investigation of the 32,270-hectare Cache Peak study area in 1992; the area had been proposed as wilderness. Bureau personnel examined and sampled prospect workings; 50 rock and placer samples were taken during the investigation. The study area is centered about 25 km southeast of Challis, Idaho, in the Challis National Forest. According to May, 1993, Bureau of Land Management mining claim records there were no current mining claims located inside the study area. Up to 100 claims may have been located in the study area in the past. Gold, silver, copper, lead, zinc: Significant analyses, poor exposure precludes resource estimate. Limestone: More than I billion tonnes may be chemically suitable for a variety of uses, markets too distant to favor mining. Dolomite: More than 1 billion tonnes may be chemically suitable for producing magnesium metal, markets too distant to favor mining. Sand and Gravel: Several million m3, but markets and transportation costs do not favor mining. Chalcedonic nodules: Two localities in the study area may be of interest to hobbyists who cut and polish stone. There is no reported past production from the study area.

Jan 1, 1993

By L. W. Higley

Particulates generated in electric furnace (EF) steelmaking constitute approximately 1 to 2 pct of the charge. This flue dust is a rich source of zinc (values are substantially higher than in ore), but although there are several processes for recovering the metal, none are considered economic in the United States. This report reviews extraction technology and presents results of Bureau of Mines reduction-volatilization tests on pelletized EF dusts which achieved high recoveries of zinc. The data are sufficiently encouraging to warrant consideration of EF dusts as raw material for primary zinc smelters.

Jan 1, 1977

To reduce accidents associated with transporting, installing or maintaining mine conveyor belts by providing easy-to-use tools for use in specific tasks. Approach The Bureau of Mines, through a re-search contract, developed three devices for use on conveyor belt systems 1) for use in moving and positioning conveyor components. 2) to reduce spillage and clean-up around conveyors, and 3) to lessen the maintenance of the belt system. The Saucer Skid Moving conveyor components using runner nose 1-beam skids is a simple task when the direction of travel parallels the beams. However, when the unit is moved sideways or around corners for final positioning, the web of the beam scrapes the floor with a bulldozing effect. Many strain and sprain injuries hap-pen when mine workers drag the skids into position at this paint. To minimize such injuries, the Bureau of Mines developed a saucer skid five feet in diameter with rounded sides and a flat bottom. Its design incorporates eight reinforced ribs with holes so the component may be secured to the skid, and eight exterior eyelets to which towing chains may be attached. The skid can be easily moved in any direction because its rounded sides slide over the mine floor rather than drag across it.

Jan 1, 1984

By C. C. Shale

A semicommercia1, high-temperature electrostatic precipitator and adjunct equipment are described, and operating characteristics at 1,470° F and 80 psig are presented for both positive and negative polarity. Removal efficiency for negative corona waS about 91 to 96 percent while that for positive corona was only about 75 to 77 percent. Results are compared with those from bench-scale investigations, and equipment limitations are discussed. Theoretical aspects of the precipitation process are related to the operating characteristics.

Jan 1, 1969

By J. Roger Loebenstein

Demand for arsenic exceeded supply, and major domestic and foreign producers allocated available supplies to customers for the fourth consecutive year. Major demand for arsenic was about evenly divided between industrial chemicals and agricultural chemicals. Legislation and Government Programs.-Effective April 1, 1981, taxes were collected from companies producing and importing 42 chemicals and petroleum products designated as hazardous, The revenue was used to begin funding of the 5-year, $1.6 billion "superfund" being established under Public Law 96-510, the Comprehensive Environmental Response, Compensation, and Liability Act, designed to help clean up spills of hazardous substances throughout the United States. As hazardous chemicals, arsenic metal and arsenic trioxide were taxed at the rate of $4.45 and $3.41 per short ton, respectively.

Jan 1, 1982

By M. W. Von Bernewitz, E. H. Denny

The use of oxygen breathing apparatus during rescue and recovery operations at both coal and metal mines has become so commonplace that there is a tendency for the industry not to give such apparetus the full measure of credit that it deserves in any particular disaster , therefore , the data presented herein should give some idea of what has been done in this regard during the past 15 years that is , up to 1910 by the Technologic Branch of the U. S. Geological Survey , and thence ( to the end of 1922) by the U. S. Bureau of Mines .

Feb 1, 1923

By Raymond L. Carpenter

In connection with its continuing studies of the characteristics of alloys and alloying elements, the Bureau of Mines investigated the crystal structure of fused boron. This report describes how the structure of fused boron was found to be rhombohedral by the powder method for crystal-structure determinations by X-ray diffraction. The determinations of the crystal structure of boron reported in the literature were made on crystals prepared by various methods such as electrolysis, thermal decomposition of a boride, or by hydrogen reduction of boron tribromide. Table 1 summarizes the data found in the literature on the crystal structure of boron. The information shows the following: (1) Three structures have been reported for boron, (2) boron prepared by different processes--or even by varied conditions of a process--produces crystals of different structure, and (3) no information is given on the crystal structure of fused boron.

Jan 1, 1960

By C. B. Manula, R. L. Sanford, R. A. Rivell

This report was prepared by The Pennsylvania State University under USBM Contract No. 60111808. The contract was initiated under the coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with M. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines.

Jan 1, 1974

Measure the leakage through individual crosscut stoppings quickly and economically so that the worst ones can be identified and repaired. (Typically 60 to 80% of the air supplied to a mine short circuits before reaching a working face.) Approach Most of the leakage through a permanent stop-ping is channeled through two windows in a temporary stopping, and air velocities through the windows are measured; leakage is determined from a formula. How It Works A temporary stopping made of plastic brattice is erected in the same cross cut as the permanent stopping, either upstream or downstream. The brattice is fastened to the roof, bottom, and ribs of the entry with spads. Normal leakage of brattice was allowed for in deriving formula, and does not effect results. For best accuracy the brattice and the stopping should be separated by a distance of one hydraulic diameter.

Jan 1, 1979

By T. F. Tomb

This paper describes field and laboratory investigations conducted on a dust-collection system recently designed for integral use with a continuous mining machine. The results of the field study showed that the average respirable dust concentration measured at the machine operator's position was reduced by about 60 percent (from 8.7 to 3.5 milligrams per cubic meter), and total and respirable dust concentrations in the return air were reduced by approximately 70 percent. The data indicated that approximately 20 percent of the dust generated at the face was not passed through the scrubber. The lab-oratory results showed that the overall efficiency (by particle count) was approximately 80 percent for total dust concentrations (minus 20 micrometers in size) typical of those encountered underground. Calculations based on total dust concentrations measured during the underground study indicated that the respirable mass concentrations of the effluent from the scrubber would still exceed acceptable levels even if scrubbing of all the air at the face were possible.

Jan 1, 1973