Search Documents

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines to evaluate the effectiveness of 10 additives to inhibit the self-heating of coal. Aqueous additive solutions were applied to a bituminous coal with a high spontaneous combustion potential, and the minimum self-heating temperatures (SHT's) of the dried coal-additive mixtures were determined in the Bureau's adiabatic heating oven. The relative effectiveness of the additives was determined by the observed changes in the minimum SHT's of the mixtures, or by the time required for the sample temperature to reach 150" C, compared with the untreated coal and a coal-water blank. Sodium nitrate, sodium chloride, and calcium carbonate were found to be the most effective inhibitors, followed by ammonium dihydrogen phosphate, calcium chloride, ammonium chloride, sodium acetate, and potassium chloride. Two additives, sodium formate and sodium phosphate, promoted the self-heating process. Differential scanning calorimetry experiments on the coal-additive mixtures showed that reactions occurred between the coal and some of the additives, but these reactions did not influence the self-heating process.

Jan 1, 1988

By Sidney Katell

An estimated capital investment of $76,499,800 will be required for a plant designed and built to produce 90 million standard cubic feet per day (std.c.f.d.) of synthetic pipeline gas through Lurgi gasification of bituminous char. This investment figure does not include the pretreatment plant, the cost of which is assumed to be reflected in the cost of the char fed to the gasification system. Shift conversion, C02 removal, and methanation are required after gasification in the Lurgi unit to make a gas suitable for pipeline transmission. Capital investment data are based upon equipment costs, January 1959. Based on a 90-percent or 330-day operating year, the operating cost before profit and Federal taxes with the char price as a variable will amount to the following: [ ]

Jan 1, 1959

The current procedure for measuring the concentration of respirable coal mine dust is as follows. Each filter is preweighed by the filter manufacturer to ±0.1 mg. Following sampling with the Coal Mine Dust Personal Sample Unit (CPSU) at 2.0 L/min, the filter with coal mine dust is sent to MSHA for weighing. The current MSHA procedure for weighing respirable dust samples uses a Mettler Model AE163 analytical balance in conjunction with an automatic weighing system with a precision of ±0.02 mg [Tomb 19901. Each balance is calibrated twice per day. Quality control for the automatic weighing system includes the systematic weighing of one in eight filters on a second Mettler AE163 balance. Tolerance is set at ±0.1 mg between the two weighings of the same sample. Weights are truncated at the 0.1 mg level (e.g., 3.457 mg is truncated to 3.4 mg) [Bowman et al. 19851. The difference of the two truncated weights is then recorded as the weight of coal dust deposited. The respirable concentration (mg/m3) is computed by multiplying by a correction equal to 1.38 and dividing by the volume of air sampled (2.0 L/min x sampling time [min]).

Jan 1, 1997

By G. T. Brow

An experimental method is described for testing diffusion of gases in crude oils at pressures and temperatures up to 3,000 psia and 200° F. A sampling technique was developed to withdraw by constant-pressure mercury displacement about 60 µl of oil from the diffusion cell through any of several 1/2-in vertically spaced capillary tubes and to trap about 4 µl of the oil in a specially designed microsampler. Oil trapped in the microsampler can be completely inserted in the sample inlet of a chromatograph. From analysis in a three-stage chromatograph (GLC), gas concentration in a sample is determined from the ratio of gas peak heights to area of peaks of reference components (hexanes or heptanes) in the oil. A diffusion coefficient is calculated from measured concentration profiles with known equations for diffusion in finite or semi-infinite systems, depending on whether the gas has or has not reached the end of the oil column. Results are given for a test of methane diffusing at 2,560 psia and 160° F in crude oil from the Weber Sandstone reservoir in the Rangely field, Colorado. A constant diffusion coefficient of 3.34 X 10-5 cm2 per sec was obtained which gives a good fit between calculated and experimental profiles determined at six times after start of diffusion. The maximum standard error of gas concentration determinations experienced with this method was ±0.88 ml per ml of gas-free oil.

Jan 1, 1970

By C. Özgen Karacan

Methane emissions from a longwall ventilation system are an important indicator of how much methane a particular mine is producing and how much air should be provided to keep the methane levels under statutory limits. Knowing the amount of ventilation methane emission is also important for environmental considerations and for identifying opportunities to capture and utilize the methane for energy production. Prediction of methane emissions before mining is difficult since it depends on a number of geological, geographical, and operational factors. This study proposes a principle component analysis (PCA) and artificial neural network (ANN)-based approach to predict the ventilation methane emission rates of U.S. longwall mines. Ventilation emission data obtained from 63 longwall mines in 10 states for the years between 1985 and 2005 were combined with corresponding coalbed properties, geographical information, and longwall operation parameters. The compiled database resulted in 17 parameters that potentially impacted emissions. PCA was used to determine those variables that most influenced ventilation emissions and were considered for further predictive modeling using ANN. Different combinations of variables in the data set and network structures were used for network training and testing to achieve minimum mean square errors and high correlations between measurements and predictions. The resultant ANN model using nine main input variables was superior to multilinear and second-order non-linear models for predicting the new data. The ANN model predicted methane emissions with high accuracy. It is concluded that the model can be used as a predictive tool since it includes those factors that influence longwall ventilation emission rates.

By R. Barany

This paper reports determinations of heats of formation (from the oxides and elements) of crystalline cadmium metasilicate and crystalline lead meta-silicate by hydrofluoric acid solution calorimetry. The results, in conjunction with known entropy values, yield free energies of formation. There are no earlier data of this type for cadmium metasilicate. The results of this investigation for lead metasilicate deviate from the literature values (which are less reliable) in the direction of increased thermodynamic stability. Both cadmium and lead metasilicate are much less thermodynamically stable with respect to their constituent oxides than are the corresponding compounds of the alkaline earth metals.

Jan 1, 1959

By G. R. Palmer

The Bureau of mines evaluated the elution of uranyl carbonate from a strong base resin with a mixed carbonate eluant in a fluidized system. The system consisted of a multiple-compartment ion-exchange (MCIX) elution column with a continuous flow of solution, except for short periods when the resin increments were withdrawn. The exchange of uranyl carbonate from the mill-loaded strong base resin with an eluant composed of 1.0 [M] NaaCOs plus 1.0 [M] NH4HCO3 was studied. The effects of solution flow rate, aqueous-to-resin flow ratio, column diameter, compartment height, initial resin concentration, and column length were examined. The experimental data indicate that for the eluant examined, a resin residence time of 240 minutes is necessary to attain 90-percent elution efficiency. Also provided is a technique for sizing an elution MCIX column form pilot plant experimental data.

Jan 1, 1979

California's coal resources are estimated to be 100 million tons, of which 50 percent is lignite, 40 percent subbituminous, and 10 percent bituminous. The occurrence of coal in California is rather limited and is restricted generally to the foothill regions of the western slopes of the Sierra Nevada Mountains. Significant quantities of coal have been mined in five areas: Ione in Amador County, Alberhill in Riverside County, Stone Canyon in Monterey County, CorralHollow in Alarneda County, and Mount Diablo in Contra Costa County. Most of the coal was rnined in the early 1900s and was used locally for fuel. Current mining operations are located in Amador County near the city of Ione. The two producing mines supply fuel to a mine-mouth co-generation power plant. The fuel coal is processed prior to burning to extract montan wax. Because California does not have primacy, coal mining in the state is regulated by the Office of Surface Mining's Albuquerque, New Mexico, Field Office.

Jan 1, 1992

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract SO122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine. Field testing was conducted during the last week of November 1972, at a coal mine operated by Inland Steel Company, near Sesser, Ill, and in the Robena No. 1 Mine, Waynesburg, Pa, on 12 March 1974. The tests included uhf propagation losses and noise (200 MHz to 1 GHz) in the Sesser, I11 mine location and vlf propagation loss and noise (1 to 200 kHz) in both of the above locations. The basic experimental parameters were frequency, polarization, antenna type/orientation, and distance. The following reports treat the various aspects of the test programs in detail. Since different antenna configurations were used in the two mines, each report contains its own experimental predictions drawn from its corresponding test activities. A test equipment list and block diagrams of typical experimental setups for the tests of section 2 are contained in appendix A.

Jan 1, 1974

By T. M. Barczak

Many of the support concepts currently used in the United States originated in South Africa. These products include the Hercules Crib1, Propsetter, MX Prop, Rocprop, and Spider Prop. Another recent development has been the introduction of hydraulic prestressing units, such as the Jackpot system, to various U.S. standing support systems. Several other prop-type supports with similarities to systems used in South Africa are in use in U.S. coal mines. Some exciting new developments that improve the installation and yield performance of props are also underway. In addition to prop-type supports, crib-type supports and single-unit systems such as the Can support are also frequently utilized in longwall tailgates in the U.S. The goal in U.S. support development is to enhance roof support capability while alleviating material handling barriers to reduce injuries associated with support handling and installation. Support products are generally full-scale tested at the National Institute for Occupational Safety and Health (NIOSH) in the unique Mine Roof Simulator load frame. The performance testing protocol is designed to simulate the full range of load conditions that occur in underground mining to identify the performance deficiencies and limitations of the support products. Once the products complete the performance evaluation, they are implemented into the NIOSH Support Technology Optimization Program (STOP). STOP is a window’s based software program that was developed by NIOSH for facilitating the design of standing roof support systems. STOP has become an industry standard to compare the performance capabilities and facilitate the application of these support products into various mining conditions. The purpose of this paper is to provide an overview of the support design and application philosophy in the United States.

Determine the appropriate spacing and alarm levels for carbon monoxide and smoke sensors used for fire detection in underground coal mine conveyor belt entries. Background Fire represents one of the most severe hazards in underground coal mines. Early-warning fire detection in underground coal mines is essential to successfully implement and execute evacuation and control measures. Both carbon monoxide (CO) and smoke sensors have the ability to provide reliable early-warning capability, provided that they are spaced properly and set at the appropriate alarm levels. The U.S. Bureau of Mines conducted a series of large-scale experiments where a small coal fire was used to ignite a conveyor belt at air velocities of 0.76 to 6.1 m/s. The test configuration was purposely designed to model a worst-case fire scenario for fires that develop within conveyor belt entries in underground coal mines. During the tests, CO and smoke levels were continuously measured to determine alarm times and alarm levels as the fire intensity progressed. The data from these tests indicated that for a given sensor spacing, the time to reach a preset alarm threshold depends upon the belt entry air velocity and cross-sectional area. Analysis of this data resulted in the equations and nomographs for CO and smoke sensor spacing, and alarm levels contained in Bureau of Mines RI 9380, "Fire Detection for Conveyor Belt Entries."

Jan 1, 1993

By Robert E. Dye

This paper describing the mining methods employed and setting forth prevailing, costs at the property, is one of a series being prepared by the United States Bureau of Mines dealing with properties in various mining districts of the United States and Canada. The Vipond mine is a gold property located at Timmins, Ontario, Canada, and operated by the Vipond Consolidated Mines (Ltd.). For the past fiscal year (ended July 31. 1930) ore was mined and milled at the rate of 310 tons per day, and the value of the bullion produced was $896,397.61.

Jan 1, 1931

By Doug Tesarik

The study of neutrinos?particles infinitesimally smaller than atoms?would be significantly advanced if a deep underground facility were available that would filter out unwanted cosmic radiation. Encouraging progress has been made in satisfying the criteria for such a facility with the selection of the Homestake Mine in Lead, SD, by the National Underground Laboratory Committee as the recommended site for a National Underground Science Laboratory (NUSL). The Homestake Mine is America?s oldest and deepest underground mine, and its well-maintained infrastructure to depths of 2438 m below the surface makes the mine an excellent site for such a laboratory. The investigation reported here is an initial study of the stability of the first of the proposed chambers. A cylindrical room with a dome-shaped roof and floor was analyzed in three dimensions using the finite-difference program FLAC3D. The results were compared to recommended support requirements based on Barton?s Tunneling Quality Index, Q. Based on model results and observations from previous mining studies, large rooms with 50-m roof spans can be constructed and will remain stable at 2141 m below the surface in the Poorman Formation when the rock is reinforced with cable bolts. Construction may be possible at lower levels in the Yates Formation if more extensive laboratory strength tests confirm initial results.

Jan 1, 2002

By Fredrick L. Johnson

No mineral resources were delineated during our investigation of the Antelope Wilderness Study Area (WSA). Only a few claims have been located in the area and only four workings were found. There has been, however, considerable exploration and mining activity in and near the south end of the study area. The Morey mining district, just southeast of the WSA, produced silver, and lesser amounts of gold and lead, sporadically from the mid-1860's through the mid-1960's. Long Lac Mineral Exploration (Texas), Inc. is actively exploring a large block of claims for hot-spring type, low-grade, large-tonnage gold deposits. Their claim block extends into the study area. The WSA, located midway between Tonopah and Eureka, encompasses approximately 87,400 acres. It is underlain by Tertiary rhyolitic and latitic volcanic rocks and by Paleozoic sedimentary rocks. At least three areas in the Paleozoic rocks have many of the favorable criterion for hot-spring type gold deposits; they have been faulted, silicified, brecciated, and hydrothermally altered, and have anomalous concentrations of precious metals and pathfinder elements. With additional exploration in the south part of the Antelope WSA, gold resources may be discovered.

Jan 1, 1986

By R. Karl Zipf

MULSIM/NL (multiple scams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines and thin metalliferous veins. It can analyze one to four parallel seams that can have any orientation with respect to the Earth's surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) nonlinear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. Detailed checks show that numerical stress and displacement calculations compare well to known analytic solutions for simple problems. The total energy release calculated by MULSIM/NL is comprised of three basic terms: (1) strain energy release from the mined-out material, (2) linear kinetic energy release due to change in gravitational potential over the mined-out area, and (3) nonlinear kinetic energy release due to nonlinear materials in the total backfill and gob area. The strain energy release term is modified to account for nonlinear stress-strain behavior in the unmined materials. Comparisons of these numerical energy release rate calculations with known analytic solutions show excellent agreement.

Jan 1, 1992

By W. E. Wallace, V. Robinson, M. F. Keane, V. Vallyathan

"An in vitro study of the biologic responses of surface-modified and native silica and kaolin was made to provide comparative information on the supression of cytotoxicity by pulmonary surfactant. The release of alveolar macrophage cytoplasmic enzyme, lactate dehydrogenase (IDH), and lysosomal enzymes B-N-acetylglocosaminidase (B-NAG) and B-ghucuronidase (B-GLUC) and sheep blood-cell hemolysis were moni¬tored as indicators of cell membrane damage and cytutoxicity. Surface modification of silica and kaolin with dipalmitoyl lecithin (UPI) resulted in complete abrogation of cytotoxicity of both minerals. These findings indicate that surface modification of minerals with different adsorption properties by pulmonary surfactant generally lessens their prompt adverse effects.INTRODUCTIONAcute and chronic silicosis are well-characterized clinical and pathologic entities resulting from the inhalation of crystalline silica (Morgan and Seaton, 1984). Kaolin, a layered aluminosilicate clay frequently mined and used in manufacturing, contains tetrahedral silica alternately layered with alumina octahedra. Kaolin is relatively .inert biologically, and distinctly greater pulmonary burdens are seen in patients with kaolinosis than are seen in patients with silicosis. Crystalline siliea (quartz) induces a significantly greater degree of fibrosis in exposed animals in vivo than does kaolin (Hamilton and Hardy, 1974; Parkes, 1982; Hunter, 1976; Sheers, 1964; Warraki and t-lerant, 1963; Lynch and Mciver, 1954; Lapenas et al., 1984).This difference in pulmonary disease associated with the two types of dust is not reflected by in vitro cytotoxicity as Jetermined by pulmonary macrophage bioassays or erythrocyte hemolysis. Cytotoxicity studies using crystalline silica and kaolin of similar size fractions show comparable bioassay response on a mass basis. These cellular bioassays, therefore, do not correlate with the relative in vivo pathogenicity of silicates."

Jun 1, 1988

By E. D. Gardner

About 300 tons of gold ore per week was being produced in February 1934 by Thomas D, Herron and Con Laster from the old lake Superior and Arizona workings; the ground was leased from the Magma Copper Co. The workings adjoined but were not a part of the Magma mine. The lessees had been employees of the Magma Copper Co, at the time the Magma closed down for the summer of 1932. Work on the lease began in July 1932 on an exposure of $2-per-ton ore disclosed in a drift; after a few hand-drilled rounds were blasted the gold content increased to about $30 per ton. Extensive sampling by pannings elsewhere of exposed portions of the vein indicated that other ore shoots existed. The last work previously done in the mine was during the World War, when lessees mined a number of small shoots of copper ore. In some of the stapes the copper miners had left a quartzose streak on the hanging wall that carried $15 per ton of gold. This material did not look as if it cried values and evidently never had been sampled. The first shipment of gold ore was made on September 28, 1932. Up to April 1, 1933, 3,778 tons had been shipped and from September 1, 1933, to January 31, 1934, 3,125 tons.

Jan 1, 1934

By M. B. Shirts

Bench-scale studies were made on a reductive hydrometallurgical procedure to convert chalcopyrite flotation concentrate to copper metal or a readily leachable sulfide. Reductive conversion of chalcopyrite and dissolution of iron and sulfur were accomplished in hydrochloric or sulfuric acid solution by the addition of metallic copper, iron, or lead. Use of metallic copper as the reductant enabled extraction of 95 and 46 percent of the iron and sulfur, respectively. The products were ferrous iron, hydrogen sulfide, and a copper sulfide. Use of metallic iron or lead as the reductant enabled extraction of 95 percent of both the iron and sulfur. The products obtained with metallic iron or lead were ferrous iron, hydrogen sulfide, and metallic copper.

Jan 1, 1974

By Charles D. Litton

Experiments were conducted to determine the optical scattering properties of diesel particulate matter (DPM) and various combustion aerosols from both flaming and smoldering combustion sources at discrete angles of 151 and 301 in the forward direction and at a light source wave length of 635 nm using a simple light scattering module. In addition to the scattering data, simultaneous measurements were made of the total aerosol mass concentration; light extinction at an average wave length of 546nm; and the response of a common bipolar ion chamber typical of residential smoke detectors modified to allow the aerosols to flow through the chamber. The results of these experiments indicate, for DPM and combustion aerosols, the intensities per unit mass concentration depend not only upon whether the aerosolis DPM or combustion aerosol but also upon the type of combustion aerosol. The results also indicate that the ion chamber responses are greatest for DPM, followed by the response to flaming combustion aerosols (FCA)and lowest for smoldering combustion aerosols (SCA). For light scattering, the greatest intensities are found for SCA, followed by the intensities from FCA, and lowest for DPM. This report describes the experiments, their results, and the use of these results to developed sign criteria for early warning fire sensor capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by the products produced from diesel engines. © 2002 Elsevier Science Ltd. All rights reserved.

By N. H. Coates

As part of a joint program of the U.S. Atomic Energy Commission and the Federal Bureau of Mines for using nuclear energy to supply process heat, the Bureau designed and constructed a pilot-scale simulated nuclear reactor system. Although workable components were developed,5 the simulated nuclear reactor could not be operated continuously at its design conditions of 2,500°F. and 250 p.s.i.g. because the refractory materials used for insulation deteriorated. Replacement of these materials with porous carbon permitted sustained operation at design conditions, and a 1,000-hour demonstration run was completed successfully. No serious operating difficulties developed during the test. Leakage of helium after 1,000 hours was only 3 to 4 std. c.f.h. Inspection after the run revealed no damage to any of the components. Including earlier runs during previous research5 the system has been operated about 4,000 hours, of which 1,120 hours have been at 2,500° F. or higher. The helium-recycle compressor performed satisfactorily with no main¬tenance whatever for 2,445 hours, with about 2,000 hours at 900° to 1,000° F.

Jan 1, 1961