Search Documents

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with tie intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By Joseph H. White

In its investigations looking to the improvement of health condi- tions and the increase of efficiency in the mining industry, the Bureau of Mines, in cooperation with the Bureau of Public Health, is studying sanitary conditions in and about mines with the intent of pointing out how those conditions that are a menace to the health of the miner may be most efficiently removed or remedied. An out- line of sanitary betterment work at mining villages in the Birming- ham district of Alabama has already been published by the bureau," and in this bulletin are presented suggestions on the planning of mining towns and the construction of miners' houses. The bulletin does not pretend to be a treatise on the so-called "housing problem," and mentions sociologic issues only incidentally. It is assumed that the influence of proper shelter on health is understood and that not a lack of appreciation so much as a lack of knowledge of the best remedies is responsible for many of the undesirable conditions that exist at mining towns. The purpose of this bulletin is to supply facts on the building of well-lighted, well- ventilated, warm, attractive, and economical houses for miners, these houses being assumed to be units of an industrial village or town the building and management of which are under the control of a corporation, so that special conditions hold which do not apply to houses built and owned by individual miners. From this it is not to be inferred that the company-controlled town is the best system or the only one in vogue. The discussion of this side of the subject in all its phases is too involved to be included in this paper. One element in favor of the company-controlled town is its possible immediate responsiveness. Hence this assumption. Also the assumption is made that a-new isolated town is being built, and hence the selection of the site, the arrangement of the streets, and the situation of the houses are discussed before the house itself is treated, for one of the most important factors in obtaining an economical sanitary house is a well-selected town site. Many of the suggestions, however, may be applied in improving conditions in existing towns, in building new houses in old towns, or in repairing old houses. Emphasis must be laid on the fact that as a rule a mining village has a shorter life than a manufacturing town. Economy is emphasized frequently because the discussion is predi- cated upon the assumption that the miner himself is to pay for all that he gets. House rent will doubtless be expected to bring in a reasonable return on all money invested in streets, sidewalks, water supply, sewer system, and houses; in other words, the town is to be run on a business and not on a paternal or charitable basis. "Fair and reasonable" precludes, of course, the idea of excessive returns. Some companies do not consider it good policy to realize as high a rate of interest as an independent realty company would be war- ranted in realizing. Under some circumstances part of the town improvements might be charged as "expense of the industry," that is, to the consumer. The isolation of a mining town introduces a unique responsibility. As the miners are practically obliged to rent the company houses, the officials of the company ought to scrutinize all expenditures in- volved so that house rent may be reduced to a minimum. In a way the town builders are placed in the position of trustees. They deter- mine, within certain limits, what proportion of a man's wages shall be spent on house rent. This consideration should restrain fanciful and unnecessarily expensive building; the other extreme should like- wise be avoided. True economy should be distinguished from cheap- ness. Ugly, insanitary, uncomfortable shacks should not be built even if, because of their cheapness, there is a demand for them from tenants. The obligation of the industry to society as a whole as well us to the tenant ought to forbid this. A cheerful, strong, healthy, virile race will not rise out of the filth and squalor of cheap hovels. An insanitary environment often does its damage slowly and silently; vitiated air does not, like mine gas, announce its deadly work by an explosion. As Talbot⚫ says: Health depends in part on freedom from infection. The probability of obtain- ing that freedom will be greatly increased by maintaining the body at a high state of vigor, or "vitality," as it is popularly called. This implies the promo- tion of all agencies which have to do with the physical well-being as well as with the control of sources of infection. Many men realize that in building houses for their workmen they are invested with a peculiar responsibility that must be wielded wisely, and in large developments they call into consultation the land- scape architect, the sanitary engineer, and the building architect, as well as the mining engineer.

Jan 1, 1914

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D. 1 Most Effective Salts A. Ammonium Phosphates Monammomium phosphate and diammonium phosphate (salts of ortho phosphoric acid) are superior to the triammonium salt in fire-resisting properties. Of these two, the monammomium salt is chemically the more stable. It is also held very retentively by a number of woods, thus reducing leaching out of the salt if exposed to water. Saturated aqueous solutions of mon- or di-ammonium phosphates have vapor preservatives corresponding to an atmospheric relative humidity of 9Z to 93 percent, the wood, will, therefore, not attract any moisture at humidities below this figure. Low concentrations (1 lb dry fire-retardant per cubic foot of the dry, treated timber) will stop flame and high concentration (5 lbs. per cubic foot) will prevent smoldering. B. Ammonium Sulphate In low concentrations ammonium sulphate has only a small effect on flame propagation, but its effect is marked when concentrations of the order of 20 percent are employed. It has no appreciable effect on smoldering. It is more corrosive to metals than are the phosphates, but is less corrosive than ammonium chloride or magnesium chloride. It is possible to leach it out of wood by prolonged and continuous action of water The vapor pressure of the saturated solution corresponds to 81 percent atmospheric humidity.

Jan 1, 1976

Only limited work has been reported in the literature about the use of latex in soil. Unisol 91 2,3 (a 9:l oil-latex emulsion made b International Synthetic Rubber Company) and Phil1ips Petroset4 geotechnic emulsions are surface soil stabilizers which penetrate a maximum of two inches, but do not reduce permeability. Diamond Alkali 5 found that styrene-butadiene rubber latex as a one percent latex-soil mixture reduced permeability to 0.7 from 21 feet per year under a head of twenty feet of brine. We have found no literature reference for use of latex as sealant at depth in the soil, although asphalt has been applied at depth using civil engineering methods6,7. Most of the materials investigated as soil sealants in the present work were latexes, although some studies were also conducted with a variety of inorganic and organic chemicals. Of the latexes tested, most were rubber but a few were plastic, e.g. polyvinyl chloride. Sealants examined in this investigation are listed individually in Table I with supplier, code number, and other pertinent information. The materials consisted of the following general classes with additional details as indicated: 1.Anionic latexes: a. styrene-butadiene copolymers and terpolymers (SBR) b. butadiene-acrylonitrile copolymer (Paracrils®) c. polyvinyl chloride homopolymers and copolymers (WC) d. ethylene-propylene terpolymer e. vinyl acetate homopolymers and copolymers (VA) f. acrylics (acrylate copolymers) g. 2-chlorobutadiene homopolymer (chloroprene) (prepared specially as cationic material coagulated by soil). 2. Water Soluble polymers: a. polyvinyl ether b. methylcellulose c. polyethyleneimines d. polyacrylic acid homopolymer e. copolymers and terpolymers with acrylic acid types (water soluble as sodium or ammonium salts) f. alginates g. monomers (for polymerization in soil, e.g. acrylamide)

Jan 1, 1972

By Maria I. De Rosa

Table 28 and figure 10 show the number of fires and fire injuries for coal preparation plants by state during 1990-1999. Table 28 also shows the risk rates, employees' working hours, and lost workdays by state. For coal preparation plants, 91 fires occurred in 1 1 states during 1990- 1999. Twenty-three of those fires caused 25 injuries (the yearly average was 9.1 fires and 2.5 injuries). Ten fires and eight injuries involved contractors. The Ewhr value was 24 1 x 10' hr (Irr = 0.02 l), and the LWD value was 198. Pennsylvania had the most fires (24 fires and 4 injuries), whereas West Virginia (22 fires and 7 injuries) and Kentucky (22 fires and 7 injuries) had the most fire injuries. Among these states, Kentucky had the highest injury risk rate value (Irr = 0.025). Table 29, partly illustrated in figure 11, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires decreased during most of the periods (an increase is seen only during the last period). The number of fire injuries show a decrease followed by an increase during the periods, accompanied by a decline in employees' working hours throughout the periods. The Irr values follow patterns similar to those shown by the injury values (see table 29 and figure 11). Tables 30-35 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 12 shows the major variables during 1990-1999. Table 36 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Seth C. Schaefer

The Bureau of Mines studied the standard free energies2 of formation of ferrous fluoride (FeF2) and ferric fluoride (FeF3) with high-temperature galvanic cells employing calcium fluoride doped with 1 mole-pet yttrium fluoride as the electrolyte. A free-energy change for the cell reaction Fe (s) + NiF2 (S) = FeF2 (S) + Ni (s) together with the standard free energy of formation of nickel fluoride yields a standard free energy of formation of ferrous fluoride from the elements of ?GF° = -168.74 + 30.63 x 10-3T ± 0.41 kcal/mole (897-1,098 K). (2) Combining the standard free energies of formation of magnesium fluoride, ferric oxide, and magnesium oxide with the free-energy change for the overall cell reaction 3MgO(s) + 2FeF3 (s) = 3MgF2 (S) + Fe2 03 (S) (3) gives a standard free energy of formation of ferric fluoride from the elements as ?Gf° = -281.45 + 90.46 X 10-3T ± 0,67 kcal/mole (880-935 K). (4) Free energies and equilibrium fluorine pressures for the two univariant equilibria of the Fe-F system are tabulated and illustrated.

Jan 1, 1975

By Mark S. Sanders

The purpose of this work was to develop and field test improved knee protection for underground coal miners working in low seam mines. In a previous phase of this contract (Sanders, 1982), experimental knee pads were developed and field tested. The field test revealed several design deficiencies with the knee pads, and suggestions for improving the design were made. The work summarized in this report, therefore, consists of modifying the design and method of fabrication of the knee pads originally describes by Sanders (1982), and of field testing the improved design. The new prototype was shorter and wider than the original design, and used a neoprene pass-through strap design rather than a cloth strap molded into the pad itself. The new prototype was constructed by slush molding a hollow bladder that was then filled with foam. Initial reactions to the pads in the field test were very positive. However, after two months, the opinions about the new prototype became less positive. They were judged, generally, to be no better or worse than the pads usually worn by the field-test participants. Problems were encountered in the field with respect to durability. Water seeped into the inner cavity of many of the pads and caused the foam to deteriorate. It was concluded that it would not be cost-effective or feasible to significantly improve upon current commercially available knee pad designs.

Jan 1, 1986

By Lisa Steiner

Almost every process has a predecessor, and studying the predecessor helps to define needs and shortcomings to be addressed in the new design. It also suggests what information is needed by the users in order for them to be able to operate safely and effectively. The end users of a system can provide important feedback to better evaluate the current and proposed designs. When new technology is introduced into a system, mishaps may occur before it is realized that human-system interactions were not considered adequately in the design process. A systematic methodology to evaluate the causes of these injuries and to develop remedial recommendations can enhance safety. This paper illustrates how such an approach was used to assess remote machine operation in underground coal mines. The dynamic work environment of underground mining with its unpredictable geologic anomalies can result in numerous hazards. Many of these hazards, including mine roof collapse, occur near the working face where coal is being extracted. The face area is also where the most intricate interactions of people and equipment occur. For these reasons, a high priority has been placed upon minimizing hazards to the workers at the face. A remote control operation was introduced to provide a safer working distance from these hazards. As the remote control technology began to be widely used for extended cut mining operations, new issues became evident. It was essential to develop mechanisms for mines to evaluate these issues in order to predict and reduce injuries. Mining methods and equipment changes must allow for the ability of workers to adapt to changes in their dynamic mining environment. Consideration should be given to how the worker will use familiar information to make decisions in now unfamiliar situations. There will be both intended and unintended consequences [Merton, 1949]. Designers try to anticipate and eliminate surprises, but it is impossible to eliminate them all. How, then, will the new system affect the tasks to workers which are currently accustomed? As suggested below, this question may be addressed and more of the unintended outcomes predicted with a planned design process which includes strong human factors input to determine interactions and behaviors of participants.

Jan 1, 2005

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with the intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By Willis Beckering

The Bureau of Mines designed a cell having four variable compartments in series to facilitate analysis of multicomponent mixtures. Use of the cell considerably decreases the time required for differential absorption analyses. A solution of a major component is placed in each compartment, and the light absorbed by each of these components is varied by increasing or decreasing the path length of the appropriate cell. Simple calculations then establish the amount of the component present. In analyzing unknown mixtures, compensation is made for compounds known to be present, and the differential spectrum representing components not accounted for is recorded and analyzed.

Jan 1, 1966

By Maria I. De Rosa

During 1990-2001, a total of 518 fires occurred in all metal/ nonmetal mining categories; 296 of those fires caused 308 injuries and 4 fatalities. Surface operations had the most fires and the highest injury risk rate values. Forty-five fires destroyed or heavily damaged facilities and equipment (including 19 pieces of mobile equipment) because of failure of firefighting methods, late fire detection, undetected fires, or fire size. In the future, many of these fires and injuries might be prevented or detected and extinguished at their earliest stage by improving current fire safety procedures, adopting existing/ improved fire detection and suppression technologies, and/or developing new technologies. Several strategies for reducing and/or preventing the number of fires and fire injuries follow. I. Increase vigilance, improve safety procedures, and develop new technologies in order to prevent fires and injuries caused by fame cutting and welding operations. 2. Improve equipment hydraulic/fuel/electrical systems inspection programs; adopt fire-resistant hydraulic fluids and electrically powered motors for use in underground mines; develop new technologies (equipment/cab rapid fire detection/ prevention/suppression systems, emergency line drainage systems, and fire barriers); adopt an optimal ground level location for the activation of emergency systems; improve operator's fire preparedness training programs; and develop effective and rapid local firefighting response capabilities. 3. Adopt existing/improved systems for continuous and early detection of combustion gases and smoke along beltlines. 4. Adopt existing/improved technologies for monitoring equipment (beltlines) operational functions. 5. Increase vigilance and adopt improved safety procedures for handling f amenable liquids and refueling fuel in the vicinity of heat sources.

Jan 1, 2004

By Eugene V. Cilento, R. Clark Lantz, Kevin A. DiGregorio

"A microscope-based spectrophotometer has been developed to measure superoxide release from single pulmonary alveolar macrophages (PAM) or other phagocytes in culture. Results indicate that PAM respond to stimulation by phorbol myristate acetate (PMA). It appears that some PAM do not release 02 upon stimulation by PMA; however, those that do release 0, show differences in: (I) the total amount of 0, released, (2) the rate of release of 02 and (3) the time delay for release of 02. The significance of measuring 02 release from single cells is two-fold. It allows the simultaneous study of 02 release and electrical potential changes across the membrane of PAM and it allows the study of differences in 02 release among cells. Thus, the function of Normal PAM and the dysfunction of PAM exposed to coal dusts can be more closely studied on single cells.Pulmonary alveolar macrophages (PAM), free cells found in the lungs, protect the lungs by removing inhaled foreign debris and bacteria. The macrophages do this by engulfing and then internalizing the foreign matter (phagocytosis). Stimulation of PAM causes the release of super-oxide radical (02) which has been shown to be the primary metabolite involved in the killing of bacteria by phagocytes (3,8,12). The super-oxide radical is highly reactive and is spontaneously or enzymatically converted to other antibacterial oxidants, including hydrogen peroxide (H202), singlette oxygen ( 02), hydroxyl radical toil'), and hypochlorous acid (HOCl) (2, 3,8,11,12).Exposure of PAM to dusts may lead to dysfunction of this cell-type and to a greater risk of lung damage or infection upon subsequent exposure to toxic dusts. To date, much of the research with this cell-type has used cytotoxicity (cell death) as a measure of dysfunction. Although this is an important end point, PAM dysfunction may occur at doses below those which lead to cell death. In addition, dysfunction has been measured using large numbers of cells. In order to obtain a clear understanding of the mechanisms involved in dysfunction, measurements should be made on single cells. As mentioned earlier, one of the major roles of this cell type is its anti-bacterial actions. Therefore, asessment of release of superoxide radical in single cells is important in determining the functional behavior of PAM before and after exposure to dusts. Since measurements of 02 production have not been made on single cells the purpose of this study is to develop the methodology needed to study release of 02 from single cells.Recent studies have suggested that a relationship exists between the release of 02 and changes in the electrical properties of phagocytes. The change in membrane potential is thought to be the initial step in superoxide production (6,9). Stimulants which cause 02 release also cause changes in the transmembrane potential of phagocytes (9) and in the permeability of the cell membrane to ions (6). For example, stimulants which cause the release of 0, from neutrophils have also been shown to increase the membrane transport of Na+ , K+ and Ca+2 and stimulation of macrophages leads to increases in Na and perhaps Ca permeability with a subsequent change in membrane potential. In some cases, phagocytic activity has been shown to depend upon the extracellular concentrations of these ions (6). Holian and Daniele (7) have shown evidence that the redistribution ofcellular Ca in alveolar macrophages is an initial step leading to 0, release. In order to provide direct evidence that 02- production is related to electrical changes across the plasma membrane of phagocytes, these two phenomena must be analyzed simultaneously on single cells. Ultimately, measurements of 0, release using the methodology developed in this study will be combined with electrophysiological tech¬niques to study both superoxide release and membrane potential changes simultaneiously on single PAM, and to examine the effects of coal and mineral dusts on their physiological fu"

Jan 1, 1988

By M. G. Cherniack, A. J. Brammer, D. R. Peterson

Over the past two decades, there have been significant reductions in industrial exposures to hand-arm vibration, especially when specific tools and work processes have been redesigned to incorporate anti-vibration and ergonomic principles. Nevertheless, Hand-Arm Vibration Syndrome (HAVS) remains a significant occupational health problem as disease symptoms continue to occur even when vibration exposure levels believed to incur low risks have been reached2. This inconsistency may be related to the methodology that is typically used to estimate workday vibration exposure levels, involving laboratory and/or very short duration field measurements coupled with estimates of overall eight-hour tool operation times determined from brief observations of tool tasks and/or self-reported surveys. One solution is to use small, commercially-available, personal vibration dosimeters to calculate, record, and display long-duration vector sums and energy equivalents of vibration. However, since these devices are attached to the worker and require tool-mounted accelerometers, they are incompatible with the worker performing normal duties involving putting down or changing tools. In addition, these commercial systems do not allow for the characterization of the transmission of vibration to the hand such as monitoring the mechanical coupling between the hand and the tool handle (e.g., grip forces). O’Boyle and Griffin showed that variations in applied force can alter vibration transmission characteristics by 50% or more indicating that the measurement of grip force is essential for modeling vibration transmissibility and vibration exposures5. In summary, a need exists for the development of a method and device that will more accurately characterize workday-long vibration exposures. Methods A portable, light-weight, Vibration Exposure Monitor (VEM) system was developed to record user-specific tool-operating times, vibrations, and grip forces throughout all, or a representative part, of a workday. It monitors frequency weighted and unweighted accelerations from a palm-mounted uni-axial accelerometer (Model 352C22, PCB Piezotronics, Depew, NY) and calculates exposure levels using the root-mean-square (RMS) and higher power mean values, such as the root-mean-quad (RMQ) and the root-mean-oct (RMO). Grip forces are also monitored using a palm-mounted force sensor (Model 400, Interlink Electronics, Camarillo, CA) from which average grip force levels and exerted grip extrema are calculated. At the core of the VEM system is a commercially available, battery-powered microcomputer (Tattletale, Model 8v2, Onset Computer, Onset, MA) with one megabyte of memory and eight analog channels using 12-bit sampling at a single-channel maximum of 100 kHz. Analog signal processing (i.e., anti-aliasing, with cutoffs at 4 and 1250 Hz, and ISO 5349-13 frequency weighting) is accomplished using custom circuitry that is directly interfaced with the microcomputer. An embedded C-based protocol governs the data collection from each channel

Jan 6, 2006

Provide reasonably priced, reliable fire protection for blasthole drills. Approach An automatic fire sensing and suppression system using both dry and gaseous chemicals was developed, and is more shock and vibration resistant than similar industrial fire protection systems. How It Works Temperature sensors mounted in the drill's machinery house, hydraulic room, operator cab, and transformer area detect the heat from a fire, and trigger a sequence of actions. The same fire fighting sequence can be initiated from manual alarm boxes in the cab, hydraulic room, or machinery house. Electrical power to the drill Is immediately cut off, and a horn sounds to warn the drilling crew. After a 40-second, built-in, delay to allow time for drill's ventilating fan to stop, gaseous and dry chemical fire extinguishing agents are piped to and released in various rooms of the drill. The gaseous extinguishing agent (Halon 1301) is released in the machinery house, hydraulic room, and operator cab where dry chemical clean-up from electrical panels and machinery would be difficult and costly. Dry chemical is piped to the transformer room at the rear of the machine. Location of the principal components of the system are shown in the drawing.

Jan 1, 1979

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

By Linda L. Chasko, Charles P. Lazzara, Ronald S. (deceased) Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

Jan 12, 2005

By R. A. Guidotti

The Federal Bureau of Mines has studied the reaction of oxides of columbium, vanadium, and tantalum with ammonia in vertical, gas-solids reactors at temperatures ranging from 300° to 1,300° C with the goal of preparing nitride intermediates for subsequent preparation of the metals by a thermal-decomposition step. The best nitride conversions were obtained in nonmetal reactors. With Cb205, V2O3, and V205 , low-temperature maxima in reaction rates occurred at 800°,800°, and 450° C, respectively, during oxynitride formation (in A1203) at 1 atm of pure ammonia. Conversion of the oxynitride, in a second step, to the mononitride was optimum at 1,200° C for columbium and 1,050° C for vanadium. In the case of Ta205, the rate of reaction to form Ta3N5 (in a single step) was highest at 900° C, where the presence of up to 5 percent methane was found to be beneficial; improved results were obtained by conducting the nitriding in a rotary kiln. Optimum space velocities (in the vertical Al203 reactor) ranged from 5,280 hr-1 for Cba205 to 7,950 hr-1 for V203. Oxide particle size had little effect upon reaction rates. Under fully optimized conditions, products containing less than 1 percent oxygen were readily obtained in under 6 hours.

Jan 1, 1975

By Stephen L. Tillim

Tubular Handles can negatively affect the contents of the carpal tunnel. Years of injuries from grasping handles for tools and machines can cause carpal tunnel syndrome, tendonitis and wrist joint injuries. The can cause inability to use a hand and resulted in the longer absences from work than injuries from falls, accidents or fires.1 Cylindrical, tubular and rectangular handles are rolled flat structures. They place the hand on a rolled flat surface where the ends of the middle and ring fingers overlap the index and small fingers. They are pulled along a series of lines that contact the end joint of the index finger, the middle bones of the middle and ring fingers and the end bone of the small finger. Cylinders are pulled diagonally in the hand toward the carpal tunnel (CT) area. Gripping in this manner tenses asymmetric muscle groups in the forearm. Handles could work better if they do not place pressure on the CT and conform to the natural function or neutral hand position where the hand rests or dangles at the side of the body, the finger tips form a diagonal, the palm and fingers form a cup, the thumb rests between the index and middle fingers and the wrist is mildly extended. However, handles designed for the neutral position are pulled by diagonally oriented fingers into the valley between the thenar and hypothenar muscles where they can compress the median nerve and tendons exiting the CT. Seven principles for handles that do not place pressure on the carpal tunnel and employ optimal hand position are presented. First, handles should align the ends of the fingers parallel to the horizontal crease and not diagonally. Second, handles should extend from the cupped fingers to meet the muscles at the base of the thumb on the radial side of the hand and extend further on the other or ulnar side to meet a portion of the small muscles. Third, handles should have a recess on the proximal side to prevent contacting or placing pressure on the carpal tunnel. Fourth, handle design should be based on hand measurements in a position of function. Fifth, handles should come in sizes. Sixth, handles should be placed on tools to maintain the wrist and elbow in neutral position. The seventh is handles should support the maximum area of the hand and absorb, but not direct, vibration to the carpal tunnel. These principles led to prototypes and patents for handles for gripping, pinching and squeezing2,3,4 . The poster will illustrate and explain the principles Bonsil handles. Research, with existing tools, is needed to substantiate claims made for the Bonsil handle.

Jan 6, 2006

By J. W. Thompson

ORE CONCENTRATION PROCESS-PATENT OIL FLOTATION PROCESS. The invention of the patent issued to Sullman, Picard & Ballot November 6, 1906 (United States Letters Patent No. 835120), is based upon the discovery of an wholly unexplained phenomenon arising from the agitation of ore pulp containing oil and air in certain proportions. This was a discovery in an art in which it was well known that the elements of oil, air, and agitation possessed certain characteristics and produced certain results. As early as 1860 a British patent first suggested the use of oil in water concentration of ores by pointing out the affinity which oils have for metallic sub- stances in preference to gangue. Subsequently many patentees employed the known affinity of oil for metal in ore concentration proc- esses by using oil in proportions varying from 2 per cent to 300 per cent of the ore and recovering the oil-coated metal particles by causing them to rise to the top or sink to the bottom of the pulp. In these processes the agitation was either gentle or thorough but never great, and though always employed to produce thorough oiling of the metal it was used in different degrees for the sole pur- pose of causing the metal particles to rise or sink. In the prior art the oil was used for its known selective affinity for metal, agitation was em- ployed to mix the oil with the metal, and air was introduced to supple- ment the buoyancy of oil in raising oil-coated metal particles to the surface. To this extent had the art of oil flotation advanced when the patentee entered it, having reached the commercial stage in only two processes, representing respectively metal-flotation and metal-sinking processes, and having reached the stage of success in none. In the line of experiments by the patentee when the proportion of oil to ore was reduced to 1.5 per cent a "float" appeared; at 1.04 per cent still more "float" appeared; at 0.32 per cent the "float" again vastly in- creased; at 0.1 per cent the "float" again vastly increased. It thus developed that in using oil at 0.1 per cent or even at 0.05 per cent of the ore and after violently agitating the pulp from 24 to 10 minutes, there arose to the surface when the pulp was brought to rest, a thick froth or foam of oil-coated air bubbles carrying oil-coated metal particles to the extent of about 90 per cent of the metal con- tent, the foam being sufficiently stable to permit removal and metal recoveries. This was a new result based upon phenomenon then unknown and still unexplained and constituted discovery and promised a change in the art of oil flotation from laboratory experi- ments and mill failures to commercial success. The patent referred to covering the points mentioned has been sustained by the District and the Circuit Courts of Appeals and by the Supreme Court. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, pp. 754-757. ORE CONCENTRATION PROCESS-OIL FLOTATION-INFRINGEMENT. The Miami Copper Co. in its process of concentrating ores by the oil flotation process used three distinct processes that were either the processes included and covered by the Sullman, Picard & Ballot patent or their fair equivalent and which were clearly an infringe- ment of the patent, and the company can not escape liability for such infringement by taking an additional step, although such additional step if taken alone would not constitute an infringement of the Sullman, Picard & Ballot patent. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, p. 768. ORE CONCENTRATION PROCESS-VALIDITY OF GREENWAY PATENT. The patent issued to H. Greenway, June 9, 1914 (Letters Patent No. 1999699), is valid. The process disclosed in this patent was a substantial departure from processes of the prior art. The heating of water is a matter of large moment and the use of acids is a matter of constant and considerable expense. By wholly dispensing with both by the use of a minute quantity of hydroxy compounds, the patentee has disclosed an original and novel plan which has broad- ened and made more simple the agitation process of air flotation. The novelty and inventive character of Greenway's discovery is patentable.

Jan 1, 1918

The following methods should be used to protect miners from the adverse health effects of exposure to respirable coal mine dust and respirable crystalline silica: ? Informing workers about hazards ? Establishing written emergency procedures ? Using engineering controls, work practices, and personal protective equipment (including respiratory protection when dust control equipment is being installed, maintained, or repaired) ? Monitoring exposures ? Conducting medical screening and surveillance ? Encouraging smoking cessation ? Maintaining medical records

Jan 1, 1997