Search Documents

By D. L. Pool

To increase metal recoveries and to minimize pollution by improved extraction technology, the Bureau of Mines investigated a hydrometallurgical technique to recover copper, lead, nickel, and cobalt from lead smelter mattes. The metals were converted from insoluble sulfides to soluble chlorides using a HCI-CI2-02 leaching system. Parameters studied in a 50-gallon, glass-lined reactor were the ratio of hydrochloric acid to chlorine, chlorine consumption per pound of matte, oxygen reaction pressure, and temperature. The matte material used contained, in percent, 19.7 Cu, 52 Pb, 2.9 Ni, 1.5 Fe, 0.38 Co, 0.19 As, 0.41 Zn, and 0.12 Cd. Extraction of Cu, Pb, Ni, Co, and Cd ranged from 92 to 98 pct, with concomitant extractions of Fe and As of <0.1 pct. The Cu and Pb were recovered as electrowon metals, while the Ni, Co, and Cd were recovered as mixed hydroxides.

Jan 1, 1981

By Stephen P. Signer

This paper presents an overview of laboratory and field tests on approximately 250 fully grouted roof bolts instrumented with strain gauges in order to study loading behavior. Laboratory work included pull tests, time-dependent tests, and shear tests. The field tests were conducted in 14 different mines extracting different commodities. However, because of the focus of this publication, only the results of tests in 9 coal mines are reported here. In the field tests, all but 14 bolts were loaded by rock movement; these 14 bolts were tested using pull gear. The variables studied included anchorage length, mechanical interlock, time-dependent behavior, shear, installation load, loading rate, and maximum load level. Such information will improve the understanding of the behavior of resin-grouted bolts, which in return will enhance the safety of miners by reducing the occurrence of rock falls. The influences of geology, overburden depth, entry width, mining-induced stresses, and bolt spacing are not described.

Jan 10, 2000

By David K. Denton

There are no active mines in the Mt. Eddy RARE II area. Chromite, gold, and stone prospects were examined. The RARE II area contains no identified mineral resources; however, a sample of a 260 ton occurrence contained 38.1 percent chromium oxide (Cr203) at the Ratero Prospect (fig. 1, no. 3), which has low potential for chromium resources. The Johnson Mine (fig. 1, no. 6) produced a small unrecorded amount of chromite during World War IT, but only a low potential exists for chromium resources. A low potential exists for gold resources at the Half Century Prospect (fig. 1, no. 2). At a borrow pit northwest of the study area (fig. 1, no. 1), sheared serpentinite is quarried for road metal; similar rock occurs in the RARE II area, but better material is more readily available elsewhere. Sand and gravel occurrences are too inaccessible and distant from markets to be considered resources. Mineral fuels and geothermal resources were not evaluated during this Bureau of Mines study. There currently are three unpatented lode mining claims in the study area. INTRODUCTION The Mt. Eddy RARE II area is 7 air-mi west of Mt. Shasta City, California, and straddles the Siskiyou-Trinity county line. The roadless area includes 7,200 acres of rugged, glacially carved, ridges and drainages which comprise Mt. Eddy. Elevations vary from 6,000 ft along the North Fork Sacramento River to 9,025 ft at the summit of Mt. Eddy. The area is covered with conifer forest below 8,000 ft elevation.

Jan 1, 1983

By Staff

This Bureau of Mines report is devoted to descriptions of investigations pertaining to underground mine trailing cables, their handling, splicing, and the use of couplers.

Jan 1, 1979

By A. T. Iannacchione

Underground stone mining represents an emerging sector for the U.S. mining industry. As this expansion takes mines under deeper cover and as more efficient mining methods are utilized, adequate stone pillar design methods will become more important. It is the purpose of this paper to examine current design practices and to discuss issues for safe mine layouts so that a rational first approach towards balancing the demands for increased production can be weighed against increased risk to worker safety from rib instabilities and pillar failures. Seventy-two stone mine pillar designs were examined. Pillars with width-to- height ratios below 1.5 and subjected to excessive stress levels appear more likely to fail. When width-to- height ratios fall below 1 .O, defects in the pillars, such as through-going discontinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties, and orientation are important factors controlling pillar strength. The influence of discontinuity dip, a characteristic easily identified in the field, was examined so that its presence could be accounted for in developing generalized guidelines for pillar design.

By P. Kovalchik, S. Peng, G. Cole, R. Matetic

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90 percent of coal miners and 49 percent of metal/nonmetal miners had a hearing impairment by age 50 (Franks, 1997). Mine workers are exposed to additional noise levels underground due to the reflection of machine-generated noise that would otherwise dissipate in an aboveground setting. Determining the sound-absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed rather than being reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes a finite room, a diffuse field and a relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper presents a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients are essential for determining and predicting potential overexposure to machine operators in different mine environments.1

By G. W. Jones

[One of the mJor c~ctivities of the Bureau ~f l;ine;: is the j.a-onotion of sdetp in mining a.nJ other inclus tries. 13 cor&apos;ncc tlcn td t~l tiiene activities the 3~.sccu r:e termine? t&apos;le cwl.os:lon ha~arls 95 n,o;r.?xs tibla Tases, vzpor s, aid scli3s aqi iavestig~ ter rnrI.?ns of controlling s-~fi. prevpri ting eqlosians.]

Jan 1, 1941

By G. W. Jones

[One of the mJor c~ctivities of the Bureau ~f l;ine;: is the j.a-onotion of sdetp in mining a.nJ other inclus tries. 13 cor&apos;ncc tlcn td t~l tiiene activities the 3~.sccu r:e termine? t&apos;le cwl.os:lon ha~arls 95 n,o;r.?xs tibla Tases, vzpor s, aid scli3s aqi iavestig~ ter rnrI.?ns of controlling s-~fi. prevpri ting eqlosians.]

Jan 1, 1941

By J. Nielen van der Merwe

For the last 3 decades, coal pillars in the Republic of South Africa have been designed using the well-known strength formula of Salamon and Munro that was empirically derived after the Coalbrook disaster. The database was recently updated with the addition of failures that occurred after the initial analysis and the omission of failures that occurred in a known anomalous area. An alternative method of analysis was used to refine the constants in the formula. The outcome was a new formula that shows that the larger width-to-height ratio coal pillars are significantly stronger than previously believed, even though the material itself is represented by a reduced constant in the new formula. The formula predicts lower strength for the smaller pillars, explaining the failure of small pillars that were previously believed to have had high safety factors. Application of the new formula will result in improved coal reserve utilization for deeper workings and enhanced stability of shallow workings.

Jan 5, 1999

By Frank D. Lamb

Pyrophyllite, a hydrous aluminum silicate (Al2 Si4O10 (OH)2 ) has been mined in North Carolina and marketed without beneficiation for the past 100 years, but recent demands for higher-grade material indicate that an economical concentration method is needed for at least a part of the pyrophyllite production. Past production has depended upon selective mining and hand sorting, which is often unsatisfactory because of the finely disseminated character of the ores. The major impurity in North Carolina pyrophyllite ores is quartz, which accounts for the abrasiveness of the commercial product. Since pyrophyllite is only slightly heavier than quartz, those ores cannot be beneficiated by simple gravity-concentration methods. Some separation can be attained by differential grinding and air classification because of the difference in hardness of the two minerals) but the separation is not sharp. Froth flotation of pyrophyllite from Quartz has never been attempted commercially, but if the demand for high-grade material is sufficient, it would seem that this process offers the most premise of being economically feasible.

Jan 1, 1950

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.

By R. L. Stein

For the past several years, the Bureau of Mines has been actively engaged in developing two new oxygen self-rescuers through research contracts with private industry. These new oxygen self-rescuers are designed to be carried by a miner while he is at work and are used during emergency escape, supplying high-purity oxygen to the user and, at the same time, absorbing carbon dioxide (C02), The first of the two new self-rescue breathing devices is a 10-minute, self-contained apparatus developed by the Mine Safety Appliance Co, Size and weight of the unit are comparable to the currently used self-rescue devices. The second device, designed and developed by Lockheed Missiles and Space Corp., is 8. 4.5-lb package which supplies 1 hour of oxygen to the miner. Both devices have a canister which contains the oxygen-producing and CO2-absorbing potassium superoxide chemical, a breathing bag, a bite-type mouthpiece, noseclip, goggles, and hoses connecting the canister and mouthpiece. When needed in an emergency, the miner removes the outer protective cover and dons the unit. For both devices oxygen is immediately available once the mouthpiece is placed in the mouth. These two new units have received prototype approval from the National Institute for Occupation and Safety Health (NIOSH) and the Mining Enforcement and Safety Administration (MESA).

Jan 1, 1976

By D. E. Shanks

The Bureau of Mines investigated the effects of HCI concentration and solution temperature on the solubility and crystal form of the chlorides of Co, Mn, and Ni when sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increasing HCI concentration in solution caused the chlo-rides of Co, Mn, and Ni to crystallize (salt out) because of the common ion effect. The salting-out crystallization was most effective for NiCI2, which had a solubility of 0.7 pct at 20° C and maximum HCI concentration. COCl2 salted out to a minimum solubility of 9.4 pct at 20° C and 22 pct HCI concentration and increased in solubility at greater HCI concentrations because of the formation of chloride complexes. MnCl2 was intermediate in behavior. The effect of temperature on solubility was greatest for CoCl2 and least for NiCI2, 15 and 7 pct change, respectively, over the temperature range of 20° to 60° C. The salted-out chlorides of cobalt and nickel formed the hexahydrates and those of manganese formed the tetrahydrate in saturated metal chlo-ride solutions at 20° C and low concentrations of HCI. Increasing the temperature or the HCI concentration caused a 108s in waters of hydra-tion. At 60° C, the salted-out crystals of NiCl2 formed the tetrahydrate in HCI concentrations up to 18 pct and the dihydrate at higher concentrations, while cobalt and manganese chlorides formed the dihydrates, even in water.

Jan 1, 1985

By Robert J. Willard

This chapter includes tables for 1982 that were not available in time for publication of the 1982 Minerals Yearbook, but does not include corresponding tables for 1983. The value of raw nonfuel minerals produced in the United States during 1988 was estimated at $21.1 billion, an increase of $1.5 billion over the value for 1982. This is a reversal of last year&apos;s downturn in value from that of 1981, which was the only decrease noted since 1971; hence, an overall trend of increasing values has been maintained for 12 years, except for 1982. Although the reversal is a basis for cautious economic optimism, it is tempered by continued problems in the domestic mining industry: inadequate funds for capital investment and competition with other countries that have lower production costs. Output of metal commodities in 1983 increased for 8 out of 21 metals, and metal values, in general, increased for 9 of the metals. Output of nonmetal commodities was mixed, with 24 nonmetals showing increases, 20 showing decreases, and 2 unchanged. Nonmetal values were also mixed in 1982: 25 showed increases, 20 declined, and 1 was unchanged. Improvements in the international metals market have not been forthcoming because of the continued depressed prices for major metals. Governments in foreign producing countries have been concerned with maintaining employment and continuing foreign exchange flows through mineral exports. Consequently, the excess of supply in the face of shrinking demand brought downward pressure on metal prices in general, except for the precious metals. On the domestic front, this situation means U.S. mining companies must become even more cost efficient. The major trend in the mining industry in 1983 was to cut costs further, reduce or stabilize total production, reduce outlays for major capital equipment, modify existing systems and equipment, and streamline operations. Most of the accomplishments reported herein reflect this trend.

Jan 1, 1984

By Barbara Fotta, Lynn Rethi

Within the Mine Safety and Health Administration&apos;s (MSHA&apos;s) classification of metallnonmetal (MAM) mining, the number of independent contractor&apos; employees has increased significantly in recent years. In 1985 independent contractor employee hours reported to MSHA accounted for 4.5% of all M/NM mining employee hours (excluding office workers); by 1994 that proportion had doubled to 9.0%. As a result, these workers now account for an increasingly significant proportion of fatal and nonfatal mining accidents. According to MSHA&apos;s statistics, annually computed fatality incidence rates (the number of fatalities per 200,000 employee hours) for independent contractors working in M/NM mining are consistently higher than those for operator employees. Over the five-year period from 1990 through 1994, 53 independent contractor employees were fatally injured while working on M/NM mine property (See Table 1). More than one third of these fatalities (36%) were due to accidents involving powered haulage; 21% were machinery accidents; and 11% percent were falling material accidents. Combined, these three accident classifications accounted for 68% of all independent contractor fatalities occurring on M/NM mine property during these years. Clearly, current efforts to increase the safety of the mining workforce must also address the safety of the independent contractor employee. This report is a preliminary attempt to identify trends in the employment and safety of independent contractor workers by identifying which segments of M/NM mining are experiencing the greatest increases in the number of independent contractor employees and by examining changes in the rates and types of accidents in which these employees are involved. The employment and accident data used in this report were obtained from the MSHA database. [ ]

By J. Davitt McAteer

Dear Mine Operator, Training for new employees, refresher training for new employees, refresher training, and new task training can mean the difference between life and death for workers. Part 46 spells out how you can develop a training program to protect workers for on-the-job hazards. Together, labor, industry, and the U.S. Department of Labor reached a milestone with the development and publication of Part 46. We want to continue working together toward the next milestone, October 2000, when the regulations take effect. We want to make sure you have all the information you need about these new training requirements. Throughout the next 12 months, MSHA personnel will be holding regional meetings across the country, delivering information and sample training plans to your operation, and offering you help to develop your plan. If you are among the many operators who are already providing training to your workers, keep up the good work. The rule will tell you exactly what is expected. If you currently have no training program, we can help you develop one. A brochure is being distributed, which highlights the main provisions of the rule. It is designed to introduce the rule to you. More detailed materials will be delivered to you. If you want information right away, simply call us, or e-mail us. We also welcome your comments, suggestions, and success stories. Part 46 will be successful and beneficial to miners through our combined efforts. Together, we can make our mines safe and healthier for everyone. Sincerely, J. Davitt McAteer, Assistant Secretary of Labor Mine Safety and Health Administration

Jan 1, 1999

By J. W. Town

The Bureau of Mines studied the effects of reducing gas composition, tem-perature, and superficial gas velocity on the regeneration rate of alkalized alumina. Regeneration was assumed to follow the simple first order reaction for removal of sorbed S02: dµ/dt = -Kµ. An Arrhenius relationship can be plotted, which shows an activation energy of about 75 kcal/mole for simulated reformed propane. The general effects of the individual gases can be described as follows: (1) CO and H2 produced rates proportional to their con-centrations, up to about 5 percent for each; (2) addition of CO2 had no effects on the regeneration rate by CO; (3) the regeneration rate by H2 was lowered by the addition of H2O while the regeneration rate by CO was increased by 0 addition; (4) H2S showed a positive effect up to concentration levels of about 2 percent and then produced a rapid negative effect; (5) carbonyl sulfate (COS) increased the sulfur content; and (6) propane was as effective in regenerating the loaded pellets as was simulated reformed propane.

Jan 1, 1971

By John J. Sammarco, Janet S. Flynt

This report (Independent Functional Safety Assessment Guidance 7.0) is the last in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and after-market suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

By Michael J. Sapko, Eric S. Weiss, Kenneth L. Cashdollar

A fundamental safety research area for the National Institute for Occupational Safety and Health (NIOSH) is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach is to develop and evaluate new and innovative seal designs that provide increased explosion protection for mining personnel. The NIOSH Pittsburgh Research Laboratory (PRL) cooperated with HeiTech Corp. of Virginia, Barclay Mowlem Construction Ltd. of Queensland, Australia, and the Mine Safety and Health Administration (MSHA) in three separate research programs to evaluate the strength characteristics and air leakage resistance of numerous innovative seal designs and ventilation control structures for use in underground coal mines. For each phase of the program, various full-scale seals, stoppings, and an overcast design were constructed in PRL&apos;s Lake Lynn Experimental Mine near Fairchance, Fayette County, PA. The seals and stoppings were built in crosscuts and were subjected to explosions to evaluate their strengths. Four pumpable cementitious seal designs ranging in thickness from 610 to 915 mm (24 to 36 in) were evaluated in the first cost-reimbursable research program with HeiTech Corp. A simple wooden framework with brattice liner was used as a form to contain the cementitious slurry during the curing period. As the seal designs decreased in thickness, higher compressive strength cementitious grout was used. All four seals withstood an explosion pressure pulse of at least 138 kPa (20 psi) while maintaining acceptable air leakage resistance. In the second cost-reimbursable research program with Barclay Mowlem Construction Ltd. of Australia, several innovative seal and stopping designs and an overcast design were evaluated. Each of the seal designs and the overcast side and wing walls used one or more air-inflated vinyl bladder assemblies anchored to the mine roof and hitched into the ribs and floor. The air within these bladders was displaced with a high-strength cementitious grout. The overcast deck consisted of a 200-mm (&apos;7.8-in) thick reinforced cementitious slab. This was the first time that an overcast structure had been explosion tested under full-scale conditions. All of the seals, stoppings, and overcast design passed the air leakage tests before being subjected to a series of explosions with static pressure pulses ranging from 14 to 475 kPa (2 tab 69 psi). Instrumentation measured seal and overcast wall displacement as a function of time. The 450-mm (1 7.7-in) thick seal in the 2.8-m(9-ft) high third crosscut withstood an explosion pressure of 170 kPa (25 psi), but failed during a later test, which generated a peak static pressure of 475 kPa (69 psi) at the seal location. A similar 450-mm-thick seal in the 2.1-m (7-ft) high second crosscut withstood three explosion tests, which generated peak static pressures of 195, 205, and 370 kPa (28, 30, and 54 psi) at the seal location. Next, the overcast design withstood four explosions, which generated static overpressures ranging from 16 to 47 kPa (2.3 to 6.8 psi). A third program at the request of MSHA evaluated the effectiveness of using pressurized grout bags (Packsetter bags) along the mine roof and ribs in lieu of floor and rib hitching for a standard-type solid- concrete-block seal. This program was initiated to address an urlusual geological mining condition encountered when building seals in entries where required rib hitching is not a viable option due to soft friable coal. Results showed that the use of these quick-setting grout-filled Packsetter bags pressurized internally to 300 kPa (44 psi) not only provides a seal that can withstand a 138-kPa static pressure explosion, but also provides a sealing option where rib hitching is not possible.

Jan 1, 2003