Search Documents

Three types of communication systems have become popular in solving communication requirements underground: Loud-speaking pager phones, carrier current phones, and magneto ringing phones. Basically, all three are simply single-channel party line systems. Although these systems are quite reliable, the single channel creates a variety of problems. For example- 1. Since no call is confidential, messages are sometimes purposely made vague, especially if accidents or safety topics are being discussed. 2. A potential user must literally "wait in line" until the channel becomes clear for his use; thus, when foremen have to wait to call in reports or supply requests, this single chan-nel creates a serious productivity bottleneck. 3. In many large mines, there are independent branch lines that must be tied together by a dispatcher, adding further delays to the system. To solve these problems, some mines have installed other phone systems-mostly commercial dial phones in industrial enclosures that offer extra channel capacity and private line features. Others have installed a system that combines both dial- and page-phone features in a single unit. Although these do represent improvements, they do not truly solve the overall problems that face modern mines. Besides extra channels, a communication system should have the following features to enhance productivity and safety: 1. A means of paging a roving miner to alert him that he is wanted on the phone. 2. Wireless-to-wired system interconnects by which a miner can talk on the wired phone system by using a remote portable radio. 3. Remote monitors that alert personnel when there is a toxic or explosive gas buildup. 4. Control interfaces that allow remote control of fans, pumps, or other devices. 5. Transmitters and receivers that can serve as emergency links. 6. Loopback that allows an alternate path of communications if the main path is cut. This chapter focuses on equipment and methods to meet the special communication needs of individuals in various places of the underground mine. The communication requirements can be broken down into four categories: 1. The mine entrance (shaft communication). 2. Permanent and semipermanent locations (shop areas, lunchroom, crusher stations, etc.). 3. Mining areas (the room-and-pillar sections, longwall faces, block caving areas, etc.). 4. Haulageways (tracked trolley haulage, diesel, belt haulage). Methods of implementing systems to meet the communication needs of these areas are described in sections 3.2 through 3.5. Section 3.6 discusses methods of satisfying special communication requirements that exist. Major topics in this category include communications with roving personnel, the isolated miner, and motorman-to-snapper communications. Emergency communication systems are described in section 3.7.Detecting and

Jan 1, 1984

By R. T. Stull, L. E. Geyer

"Previous Work:As outlined in previous papers* ond clays for graphite crucibles have been tested at the plants of the Detroit Lubricator Co., and the Detroit Copper and Brass Rolling Mills, Detroit, Mich.These tests indicated that there were two American clays (Missouri pot clay and Illinois kaolin) that tested better than the Klingenberg (German) clay. Dorset (English) ball clay was tenth in the list.Making the Crucibles:After it had been determined that American clays can be used successfully in graphite crucible manufacture and service, the next step in the investigation was to determine the value of American graphites as compared to the foreign, These final tests were carried out at the plant of the Detroit Lubricator Co., through the courtesy of Mr. G. B. Duffield. The crucibles, as previously. were made at the plant of the Vesuvius Crucible Co., Swissvale, Penna., from a formula compiled by the Bureau of Mines and under the supervision of Bureau engineers.The graphites to be tested were given an initial to indicate their source. The number of crucibles made and shipped are set forth in Table 1."

Nov 1, 1923

By Wallace W. Roepke

The Bureau of Mines has a well-established health and safety research effort directed to fundamental studies of the mine cutting system. This report describes the ignition danger of using cutting bits with flat wear area on still-intact carbide inserts.

Jan 1, 1983

By Fred N. Kissell

In this report the importance of diffusion in controlling the emission of methane in mines is examined. An in-situ diffusion parameter is defined and calculated for a hypothetical unfractured lump of coal in the Pittsburgh and Pocahontas No. 3 coalbeds. The values obtained are similar to those obtained with lump coal in laboratory experiments.

Jan 1, 1972

By M. K. Larson, B. G. White

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the causes and mechanisms of roof failure in underground mines. It is expected that a better understanding of these causes and mechanisms will lead to better layout and support designs that will help prevent accidents and fatalities associated with fall of ground. Two numerical experiments were conducted by NIOSH researchers using the Fast Lagrangian Analysis of Continua (FLAC) computer modeling program with a strain-softening continuum to simulate fracture zones. Two models, one of a round hole in a plate and one of a rectangular opening, were constructed and boundary conditions were applied to simulate far-field shear. The Particle Flow Code in Two Dimensions (PFC2D) computer program was used to look at the effects of far-field shear in generating fractures around an underground opening, but these models are preliminary until boundary conditions, strengths, and stiffnesses are matched to the FLAC models. Results showed that shear zones propagated from the opposite corners of openings in directions that appeared to be determined by opening shape and far-field stress. Tensile failures also formed and extended away from these shear zones. The consistent direction of shear deformation with respect to far-field shear provides a plausible explanation for preferred directions of shear as seen in geologic environments.

Treat contaminated coal mine drainage to meet EPA and State water quality requirements. Approach A model (fig. 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of abandoned mine lands (AML). The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions.

Jan 1, 1992

Provide the mining industry with a method for determining the gas content of ore bodies and associated strata for use in mine planning, Approach Samples of various rock types are collected and tested to determine gas content in conjunction with sample size, the collection method (i.e. whether the sample was collected from a core sample or by hand) mine gas emission, and the geologic location from which the sample was taken, such as near a fault, outburst area, or other geologic anomaly. How It Works Two methods were developed by the Bureau of Mines to determine the gas contents of rock samples. The first method developed involved dissolving minerals to measure gas emission. This method, however, can only be used with soluble minerals. A second method, therefore, was developed for use with insoluble minerals. With this method, the sample is crushed in a ball mill. Although the dissolution method is faster and more accurate to use, the crushing method is also advantageous because its use can more closely approximate a mining situation; the sample is crushed as in mining and the amount of gas released relates to the amount of gas that would be released during a mining operation. The dissolution method is applied to soluble minerals, such as rock, salt, or trona, in a sealed chamber. Gases released during dissolution are collected for analysis by gas chromatography. One advantage in using the dissolution method is that the test apparatus is relatively inexpensive. In addition, test can be performed at any scale, from single crystal samples to a solution mining operation.

Jan 1, 1983

This Part is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a corner. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency which propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1974

By Sumner M. Anderson

ATHOUGH scattered signs of increased activity in the mining industry accompanied an incipient improvement in the overall economic situation during the latter months of 1963, production levels for the year as a whole responded to the general 1962-63 business recession with a 4.2 percent decline. The petroleum industry, active since 1907, did not become a dynamic force in the economy until exploration and drilling contracts were concluded with private companies in 1958 and 1959; on November 15, 1963, having virtually achieved self-sufficiency in petroleum in the preceding year, those contracts were unilaterally annulled. In the field of metallics, the only approach to internal sufficiency-aside from the iron and steel industry that has depended heavily on the importing of basic raw materials-has been in mining, smelting, and refining lead and zinc although iron ore, silver, beryllium, tantalite, and tungsten have been mine production items of economic significance. Reserves of lead, zinc, silver, bismuth, vanadium, and low-grade and metallurgically difficult iron ore-as well as those of beryllium, tantalite, and tungsten which are produced primarily for export-appear to be fairly abundant. The exploration of deposits of copper, cobalt, tin, lithium, gold, manganese and uranium has been undertaken on a relatively small scale, and little precise information is available on the extent of reserves. Argentina is dependent on foreign sources for part of its required iron and steel and, except for lead and zinc, most of its nonferrous metals. Nonmetallies and solid fuels present an exceptionally varied array of production items among which cement had the second largest 1963 output in South America. Borates, bentonite, common clay, diatomite, fluorite, granite, lime, limestone, obsidian, onyx, rhodochrosite, salt, and spodumene ordinarily are produced for export either exclusively or in excess of domestic consumption requirements. Barite, cement, chalk, gypsum, marble, and mica are both exported and imported. Argentina depends entirely or partly on imports for coal and coke, certain special types of clay, mineral abrasives, graphite, magnesite, mineral fertilizers, sulfur, talc, and minerals for construction, the last group being chiefly attributable to convenience of river transport from Uruguay.

Jan 1, 1964

By Carla A. Kertis

Because coalbed discontinuities often pose serious economic and safety problems in underground coal mines, criteria were documented for the recognition and prediction of discontinuities in advance of mining. Pennsylvanian strata in Indiana and Armstrong Counties, PA, were deposited as part of fluvio-deltaic complexes with channel-phase sandstones as the predominant type of coalbed discontinuity. Coalbed isopach maps constructed for this study delineated numerous want areas (areas of no coal) with elongate to linear geometries. A comparison of coalbed isopach and corresponding sandstone isolith maps of the study area revealed many examples of a thick-sandstone, thin-subjacent-coalbed relationship. Nearly 60 pct of the want areas in the study area were found to lie subjacent to thick (> 20 ft [6 m]) sandstone accumulations. In addition to erosion of the coalbed, channels may contribute to coalbed splitting, coalbed thinning over paleotopographic highs, abnormal coalbed thick- nesses, and deterioration of coal quality. If these features are considered, then approximately 80 pct of all interruptions in the economic coalbeds in this area result from channel activity. By using the criteria developed in this study and described in this Bureau of Mines report, the occurrence of coalbed discontinuities may be predicted and anticipated in advance of mining.

Jan 1, 1985

Preventive maintenance practices are listed in the manufacturers' instruction books. In general, equipment that requires frequent and extensive preventive maintenance is generally the most costly. The manpower spent on these frequent trips to remote areas is such that it is usually better to invest in a more costly system which requires little preventive maintenance. The best preventive maintenance for the system is a good installation. 7.2 Preventive Maintenance and Inspections With any system, periodic inspection is required because of the corrosive atmosphere and adverse conditions that exist in underground mines. These inspections can spot potential trouble in the system. Repair or replacement at that time averts the possibility of losing effectiveness of all or part of the system. 7.2.1 Cables Approximately once per month all cables in the communications system should be inspected for kinking, chafing, cracking, wear, stretching, or other signs of physical abuse. Particular attention should be paid to cable glands at the entry or exit points to the various units in the system, where the cable goes around sharp corners, in the vicinity of holding cleats which may be clamping the cable too tightly causing potential damage, and across the areas where the cable is exposed to physical damage from outside sources, such as equipment or falling objects. If a cable is damaged, it should be replaced as soon as possible. It is mandatory that the ground leads and connections to carrier current phones be thoroughly inspected and maintained in good condition, since considerable hazard may exist to the operator or equipment if a ground connection is broken. 7.2.2 Pager Phones The most readily available test set to determine if a pager telephone is operating correctly is the pager phone itself. The following physical check of the system can be performed at any phone station. 7.2.2a Listen Circuit Remove the handset from its cradle and listen to determine if the circuit is functional, as indicated by the presence of noise or conversation on the line. If no noise or voice signals are present at the handset receiver, take the following corrective action: 1. Operate the handset press-to-talk switch several times. Any corrosion on the contacts of this switch may cause a receiver to be temporarily inoperative. Repeated operation may clear the condition. 2. Open the cabinet and see if the battery cables are properly connected and are making firm contact. Check the handset cable and its connections in the cabinet of the pager phone, and see if there is any evidence of a break in the cable, corroded contacts, or poor connections. 3. Remove the handset receiver earpiece by unscrewing it counterclockwise (to the left), and remove the receiver from the socket. Examine the handset cavity; in some units, a patch of cotton batting or floss is used as a barrier to reduce acoustic feedback in the handset. If the cotton patch has absorbed moisture, remove it and replace with a crumpled ball of soft rubber, stuffed just far enough into the handset so it will not touch the receiver or switch terminals. 7.2.2b Page Circuit and Talk Circuit Push the page switch, squeeze the handset press-to-talk switch, and call any other phone. Release the page switch

Jan 1, 1984

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 5 Typical Input - Ouput The input data and the printed output for case 8 of the simulations (Section A.4) are shown in the following. The branch, level, node, miner and hoist numbers mentioned in the input and output refer to the corresponding numbers in Figures A-3, A-4 and A -5, The plotted ouput, already shown in Figures A,11 and A-12 is not repeated. The input data shown does not include the following simulation parameters: DTIME = 0, 05 FTIME = 130 JPLT(K) = 1 for K = 1, 2, 3 0 for other K TPLSTR = 0.0 TPLST P = 130

Jan 1, 1976

By D. Eugene Rannels, Yu-Chen Lee, John W. Swisher

"Inhaled dust particles of appropriate size contact cells of the alveolar region.' The acute response to coal dust appears to involve a variety of cell types, including alveolar epithelial cells, interstitial fibroblasts, both resident and recruited macrophages, and cells of the immune system. Direct and indirect effects of dust, which may be mediated by soluble factors,'' can initiate acute and long-term lung injury. While it appears that epithelial cell growth and differentiation, along with integrity of the epithelial basement membrane, may play a role in the long-term response to dust exposure, little is known of the role the alveolar epithelium may play in the progression of injury. The broad hypothesis that underlies these experiments is that short- and long-term consequences of coal dust exposure involve changes in structure and function of the alveolar epithelium and the underlying extracellular matrix. Recent studies show that coal dusts exert direct effects to modify pulmonary epithelial cell-extracellular matrix interactions in vitro.3EXPERIMENTAL PROCEDURESType II cells isolated on day 0 by density centrifugation and differential attachment4 were plated overnight in D MEM containing 10% fetal calf serum before exposure to anthracite dust PSOC 867 sonicated into culture medium (750 ug/mL).3 Synthesis of extracellular matrix proteins was determined on day 3 of primary culture, as detailed elsewhere. 5 Cells were removed from extracellular matrix by extraction with NH4OH and high salt. Extracellular matrix synthesis and fibronectin content were evaluated based on radiolabeling with 3 H-leucine and on Western blot analysis, respectively. Additional analytical methods and calculations are detailed elsewhere.3-5"

Jan 1, 1998

Native asphalt was produced in 1977 by six companies in four States. Leading States were Texas and Utah. Output declined 39% to 1,237,000 tons valued at $18,874,000. Bituminous limestone was produced by Whites Uvalde Mines and by Uvalde Rock Asphalt Co. in Uvalde County, Tex.; by Southern Stone Co. in Colbert. Ala.; and by Barton County Rock Asphalt Co. in Barton County, Mo. Gilsonite was produced by American Gilsanite Co. in Uinta County. Utah, and by Ziegler Chemical and Mineral Corp. in Weber County. Utah. The asphalt was used for streets and roads, and for other purposes.

Jan 1, 1980

By Raymond F. Helinski, Linda J. McWilliams, Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

This report examines the boom arm vertical speed for roof bolting machines to study a moving boom arm appendage at different speeds during different work scenarios. The goal of this study is to determine the impact of the appendage speed on the likelihood of the operator's hand, arm, head, or leg making contact, such as touching the moving appendage. The overall research goal is to reduce workers' risks to injury from exposure to underground mining machinery. Accident investigation reports from the Mine Safety and Health Administration do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are not feasible because of safety issues. As an alternative, researchers used a unique computer simulation model that uses a virtual human, vision tracking, and generates random virtual human motions and risky work behaviors. By using specialized software to simulate the computer model, researchers accurately identified potential hazards of tasks where it is not possible to perform experiments with human subjects. Results of a frequency distribution analytic approach show that, regardless of other variables, contact incidents were always greater when the boom was moving up, always greater on the hand, and always greater or the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom is ascending. Results of a cross-tabulation analytic approach show that the 25th-percentile operators experienced more contacts than other operator sizes and had most of their contacts during a boom speed of 13 in/sec. The hand-on-boom behavior during drilling and bolting tasks experienced more contacts than other work behaviors, and both tasks had most of their contacts during speed 13 in/sec. The 60-in seam experienced more contacts than other seam heights and had most of the contacts during speed 16 in/sec. For univariate logistic regression models, seam height is the most important predictor of the probability of a contact. However, a multivariate logistic regression model predicted contacts are more likely with the both-knee work posture in the 60-in seam, a 25th-percentile operator compared to a 55th-percentile operator, and speeds 16 and 22 in/sec compared to 7 in/sec. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speeds greater than13 in/sec result in a substantial increase in risk to the roof bolter operator making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Virtual operator's response time has little effect on the number of contacts experienced. The mining industry can use the information in this study to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine's boom arm.

Jan 5, 2005

By John S. Berber

Bureau of Mines research on the production of phthalic anhydride by vapor phase oxidation of hydrocarbons began at Morgantown, W. Va., in October 1960. For these preliminary studies, a known solution containing naphthalene and 1-methylnaphthalene was used. In another series of tests, pure naphthalene was dissolved in different solvents. A series of investigations was conducted with the neutral oil fraction (210° to 270° C) of a low-temperature tar obtained from the Texas Power and Light Company's low-temperature carbonization unit. The neutral oil fraction was first dealkylated, and then the product was distilled into 210° to 250° C and 250° to 270° C fractions. These two fractions were then subjected to catalytic vapor phase oxidation. Although a number of catalysts was tested, most of the experiments were made using 9 percent vanadium pentoxide on inert alumina. The activity of this catalyst did not decrease after 162 hours at 1,030° F. Studies were conducted over a temperature range from 610° to 1,180° F. An operating temperature of 1,030° F yielded 47.50 percent of phthalic anhydride from a synthetic mixture of naphthalene and 1-methylnaphthalene. The highest yield (84.40 percent phthalic anhydride) was obtained with naphthalene dissolved in toluene and also with naphthalene dissolved in methyl ethyl ketone. With a 210° to 250° C fraction the highest yield of phthalic anhydride obtained was 12.32 percent at a temperature of 900° F, and, with a 250° to 270° C fraction, it was 15.80 percent at a temperature of 875° F.

Jan 1, 1963

By J. Schlocker

The present emergency has greatly stimulated interest in the light metals - aluminum and magnesium - owing to their extensive use in airplane construction. The $63,000,000 plant being erected in the Las Vegas Valley by Basic Magnesium, Inc., under the auspices of the Defense Plant Corporation,

Jan 1, 1942

By G. V. Sullivan

This report describes an investigation by the Bureau of Mines of flotation techniques for the recovery of chromite from fine-grained disseminated ores. Reported work on the concentration of chromiferous materials shows that flotation has been applied almost exclusively to slime-free pulps. Therefore, chromium recoveries that could be obtained by flotation were related to the amount of slime rejected. However, results of recent studies by the Bureau of Mines showed that des liming is not a requisite to selective concentration of chromite. Laboratory-scale tests on seven ore types from the more important chromium-bearing areas of the Pacific Northwest showed flotation to be technically feasible for treatment of all but one of the samples. Concentrate grades were affected more by the composition of the chromite mineral than by the grade or character of the ore. Test results from three of the samples showed that, without prior desliming of the pulp, 78 to 91 percent of the chromium could be recovered in concentrates of 90 percent or more chromite; two samples responded to similar treatment, resulting in concentrates of more than 80 percent chromite with recoveries of 85 and 89 percent chromium. One sample of mill products, subjected to severe weathering, required removal of the primary slime to obtain a concentrate of 65 percent chromite with only 75 percent chromium recovery.

Jan 1, 1960

By H. Billmayer

This report covers the period from June 17, 1974 to February 20, 1975, and describes the work performed in compliance with the requirements of Contract No. H0346102 and Modification No. 1 thereto. The purpose of the contract was to design protective canopies for an Elkhorn Scoop, a Lee Norse Miner, a Wilcox Miner and a Wilcox Bolter; to construct mockups of the canopies; and to obtain machine operator evaluations of the canopy designs by assessing the mockups while installed on their machines in the mines. The overall program objective was to achieve protective canopy designs for the four machines which would be acceptable to the operators.

Jan 1, 1975

By E. A. Johnson

As part of its effort to reduce the environmental impact associated with mining and metallurgical operations, the Bureau of Mines used a modified form of the Environmental Protection Agency's Extraction Procedure toxicity test on copper reverberatory slags that contained low, medium, and high levels of the impurity elements As, Pb, Sb, Bi, and Zn. All tests resulted in extracts that did not exceed those limits published in the May 19, 1980, Federal Register; there-fore, these solid wastes were designated as nonhazardous for most landfill disposal situations. However, arsenic and lead levels disturbingly close to the allowable limits--and even higher levels of copper and zinc, for which there are no established limits--leached from the high-impurity-element granulated slags. These slags should be handled in such a way so as to minimize the possibility of water contamination. One baghouse dust was tested according to the EPA procedure and found to exceed the extract limits by a factor of 10. This solid waste may be considered hazardous.

Jan 1, 1982