Search Documents

By Thomas Varley

Data on the consumption of reagents used in flotation during the years 1923 and 1924, in metallurgical plants in the Unites States, are presented in this paper. Two previous reports Lave been issued by the Bureau of Mines on consumption of oils and other reagents used to flotation - namely, "Statement of Flotation Oils," by O. C. Ralston, issued in 1913, and Serial No. 2203, "Consumption of Reagents Used in Flotation," by Thomas Varley, for the year 1919, issued in January, 1921.

Jan 1, 1925

Use controlled blasting techniques to reduce blast-produced overbreak damage to underground mine ribs and back for both safer working conditions and improvements in productivity. The Problem Blasting is used in metal and non-metal underground mine slopes, drifts and crosscuts to fracture rock to be excavated and further processed. Standard blasting also produces fractures in the rock beyond the desired excavation area. This is sometimes evident by rough surfaces, undercutting and other signs of excessive damage. This damage contributes to rockfalls in the mines, a major cause of injuries and fatalities, and equipment damage. A variety of controlled blasting techniques has been developed for civil engineering projects where long-term stability is essential. For several reasons, these methods arc not widely used in mining. For example, these methods incur additional costs and time; there is little need to maintain stable openings over long periods of lime; and there is the perception (hat corrective remedial techniques, such as rock bolting, are more practical. Basically the benefits of these methods are not demonstrably clear for application in underground mines.

Jan 1, 1991

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By David E. Nicholson

This report investigates the mechanical behavior of fine soils in a lunar environment in engineering gravity-flow bins. The ultrahigh vacuum, absence of moisture, and a lunar gravity one-sixth that of earth gravity represents a unique environment, both advantageous and detrimental to these systems. On earth, moisture and gases contained in powder masses can be responsible for complex descriptions of gravity flow. Their absence appear to simplify the lunar soil behavior. However, simulation of the lunar gravity and vacuum complicates the development of experimental data for designing bins. The properties of a dry soil powder, its behavior under one-dimensional compression, and its torsional and direct shearing strength under earth atmosphere are described in part 1 of this paper. These properties provide the parameters for a finite-element analysis to optimize the design of bins, to be described by Dr. William Pariseau in part 2. Shear tests assess the failure criteria for the material. Compression tests provide modulus and (Ko) stress-ratio values from the loading portion of the compression cycle, duplicating the condition of a bin at rest with the discharge closed. During the unloading portion of the compression cycle (soil overconsolidated), the residual Ko values rise. It is postulated that this phenomenon creates a high-lateral stress in bins when they approach incipient flow. Assessment of the Ko value, overconsolidation ratio, and the void ratio state is proposed as a criterion to determine the flowability of powder.

Jan 1, 1971

By Eliot J. White

The physical properties and clay mineral content of the major oil-producing formations in the Powder River Basin of Wyoming were determined by analyses of cores from 100 wells. Interrelationships were established among permeability, restored water saturation, clay content, and bulk swelling capacity of the crushed sample and used to estimate the susceptibility of the formations to water damage. The ratio of water permeability to gas permeability (kw/ki) offers a convenient scale for semiquantitatively estimating the water sensitivity of sands. The irreducible water saturation was also found to have a similar relationship to the clay mineral content and the water sensitivity of the sands. The average relation of water permeability to gas permeability is different for each sand, as shown by the curves, and the relative positions of the curves indicate the degree of water sensitivity of each sand from which the susceptibility to water damage may be estimated. How accurately these estimates show formation behavior under field operations will not be known until studies of field performance can be made. The water permeabilities of the Muddy, Minnelusa, and Tensleep sands average about the same as the gas permeabilities, and these sands are classified as insensitive. The water permeabilities of the Sussex and Shannon sands, at the other extreme, are much less than the gas permabilities [when average ki is 30 millidarcys (md), kw is 6.1 md], and these sands are classified as highly water sensitive. The sensitivities of the five other sands are between these extremes.

Jan 1, 1962

By H. C. Ko

The Bureau of Mines maintains an active program in thermochemistry to provide thermodynamic data for the advancement of mineral science and technology. As part of this effort, the standard enthalpy of formation at 298.15 K, ?Hf°, for 2CdO-CdSO4 was determined by HCI acid solution calorimetry to be -345.69 ±0.61 kcal/mol.

Jan 1, 1983

By Fred N. Kissell

This U.S. Bureau of Mines report is a guide for the control of air contaminants during tunnel construction. Topics discussed are calculating air quantity requirements, types of ventilation systems, planning ventilation systems, control of methane gas, control of dust, control of diesel emission, ventilation to remove blasting fumes, measuring airflow, and measuring gases. This report does not provide detailed design information, but seeks to answer practical questions on air contamination issues.

Jan 1, 1995

By John C. Franklin

A radon survey was made at five different locations in the Twilight mine near Uravan, Colo., to determine chances in radon concentrations in an inactive mine. Data were taken with a continuous monitor set for 1-minute count periods and readings were taken 24 hours a day for 9 days. The 12 readings per station each hour accurately showed how t w radon concentration varied during the day. From the data collected from the intake portal to station 4, the average radon emanation rate was estimated at 18 picocuries per second per square foot (pCi/sec/ft3). A daily cycle in radon concentration was detected that apparently was related to barometric pressure change.

Jan 1, 1976

By S. P. Kinney

[The blast-furnace operator is often confronted with the problem of determining the size of the materials which are used in the furnace burden. The statement is heard that the coke is larger or smaller or that certain ore is finer than that previously used. A screen analysis of the materials used gives a measure of the different sizes of materials in an aggregate. When one is fine and the other is coarse, the difference is obvious; but when the materials are of similar sire, it is more difficult to estimate the degree of finances or coarseness. In considering raw materials it would be desirable to be able to judge the size of the radio ideal materials entering the furnace and the burden as a whole, by one representative value, such as the average size of particle. Previous work by Perrott and Kinney3 developed a method for measuring the average size of particle in a mass of finely ground materials, and an attempt will be made to apply this method to the materials included in the blast-furnace charge and to the entire burden.]

Jan 1, 1930

By W. E. Dennis

"INTRODUCTION The strategic importance of zinc warranted investigation of the Silver Eagle zinc prospect, which was first examined by an engineer 3/ of the Bureau of Mines in January 1943.From October 12, 1943, to March 16, 1944, the Bureau explored the deposit by trenching, core drilling, and sampling to establish the amount and grade of ore and to test for the presence of sulfide-ore minerals at depth.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Oct 1, 1946

By John I. Kasteler

The Rambler mine is in the Douglas mining district, Albany County, Wyo. (fig. 1). The property was first operated about 1870 for gold found in the outcrop of a leached ore body. Copper and metals of the platinum group were discovered, in 1900, or soon thereafter, and intermittent mining was done until 1918, when a fire destroyed the surface plant, and the underground workings caved. The mine has since been idle. The Bureau of Mines conducted a development project on the property from October 1942 to October 1943, with a recess period between November 1942 and August 1943. Ten diamond drill holes, totaling 1,859 linear feet, were drilled on the property (fig. 2). The mine dump was sampled after preparation with a bulldozer. Assay determination and spectrographic analyses disclosed small quantities of copper and metals of the platinum group in the samples. Determinations were made on 11 samples from the diamond drill holes and 23 samples from the mine dump. The assay results and spectrographic analyses are given in tables 1 and 2. The logs of the diamond drill holes are given in an appendix to this report.

Jan 1, 1949

By R. W. Stahl, H. E. Sanford, J. B. Benson

"As movement or transportation of coal is second only in importance to actual mining, and as the latter is wholly dependent on the former, the efficiency of the haulage system often determines the efficiency of the entire plant. Safe or accident-free transportation is essential, also, because no attempt is made to divorce safety and efficiency, it being realized that they are inseparable.Most of the Ruhr mines were opened decades ago, and many features that were considered up-to-date then are now obsolete. Progress in developing haulage systems has been slow, chiefly because it would be very costly to change many to accomodate more modern equipment. These systems are being altered or modernized slowly, as capital permits. The only revolutionary changes that have been made in mine haulage are the use of larger locomo¬tives and cars, in the movement of shuttle cars, and in the adoption of skip hoisting. Most Ruhr shafts, however, will not accomodate large cars, the secondary roadways are too narrow for large locomotives, and the coal is too soft to permit skip hoisting because degradation would be too great. Therefore, notable advances have been made only at newer plants, where allowances have been made for modern equipment.The shafts are deep (average 2,300 feet) and of comparatively small diameter. The small bore was designed to reduce costs of sinking and lining. Generally, the shafts are lined throughout with masonry; however, most of the buntons and guides are wooden.The hoisting engines arc installed in masonry structures, and where more than one hoist is used they are placed on opposite sides of the shaft to eliminate as much noise as possible (fig. 1). This arrangement also prevents an engineer from acting on any signals except those transmitted to him. A few hoisting engines are mounted in the headframes (fig. 2). The hoisting engines are equipped with overwind, overspeed, and auxiliary braking devices, which are tested frequently and kept operative at all times. The signal code is displayed in view of the engineer, and a light or dial indicator informs him of the cage's position in the shaft. Many hoists are equipped with re¬cording devices, which show on a continuous chart the speed of hoisting as well as any delays throughout the 24-hour period.A Koepe system of winding is in general use because of the depth of shafts (fig. 3). With this system, a single rope passes over a single-groove, large-diameter sheave attached to the motive power, and the ends of the rope, after passing over the head sheaves, are attached to the cages. A flat tail rope suspended in the shaft and connected to the bottom of the cages serves to balance the system. Both steam and electric engines are used to activate the hoisting system, end the engines are capable of moving at least a 50-percent overload.The ropes are necessarily of large diameter (2-1/2 inches and greater), and flexibility decreases as rope diameter increases. To overcome the unwieldiness .of large-diameter ropes as shafts become deeper, a four-rope system is being tried at one mine (fig.4). In this system the load is equalized between four ropes which permits much smaller ropes to be used. All hoist ropes are inspected daily and discarded after 2 years service unless special permission for longer service is granted by the Mine Inspectorate, and then only after thorough visual and electromagnetic inspection."

Jan 1, 1950

By D. A. Doughty

The Bureau of Mines developed two methods for determining iron II and iron III in 2- to 5-mg samples of coal using electron paramagnetic resonance (EPR) spectrometry. One method used solid coal samples; the other method used aqueous solutions. The method using solid samples was more simple, technically, but required the use of X-ray fluorescent analysis, or another independent method, for determining total iron in the samples, and the results were subject to some uncertainty. The method using aqueous solutions appeared capable of greater certainty and did not require additional methods of total iron analysis but was more involved procedurally. The coals analyzed were found to contain much more iron II than iron III.

Jan 1, 1973

To provide coal operators with an easy-to-use stress control design procedure to minimize coal mine bumps during room-and-pillar retreat mining conducted with available continuous mining machine technology. Approach The goal of this U.S. Bureau of Mines (USBM) re¬search was to facilitate safe and efficient room-and-pillar retreat mining of bump-prone coalbeds by limiting coalbed stress adjacent to expanding gob areas through variation of section layouts. The first step was design of total-extraction pillars and their associated pillar-extraction plans. The second step was development of a coalbed strength model. The third step was development of stress limit design criteria. The fourth and final step was development of a methodology to estimate the magnitude and distribution of development and abutment loads apllied to the pillar line. The linear geometry of unlimited-width sections allowed for the accomplishment of step four with the tributary-area and linear shear-angle concepts. Increasing overburden depths required limited-width sections separated by barrier pillars to control stress within total-extraction panels. The accomplishment of step four with limited-width section designs required prediction of abutment load distributions for rectangular gobs and apportionment of these loads over mixed pillar sizes. A parametric study of the complicated interaction of various combinations of overburden depths, total-extraction panel widths, and abutment pillar widths was conducted with the USBM-developed boundary-element program MULSIM/NL.

Jan 1, 1995

By Brian L. Quick

Problem: The National Institute for Occupational Safety and Health's [NIOSH] National Occupational Research Agenda (DHHS Publication No. 96 115) reports that approximately 50% of miners will experience hearing loss by age 50, compared to only 9% of the general population. The present investigation examines three antecedents believed to be associated with miner's use of hearing protection. Method: A posttest delayed posttest control group field research design was employed to assess antecedents toward wearing hearing protection. Results: Following the initial posttest, miners' attitudes and subjective norms were antecedents to intentions to wear hearing protection devices. Also, intentions toward wearing hearing protection predicted hearing protection behaviors. Approximately six weeks later, miners' attitudes and perceived behavioral control were each significant predictors of intentions to wear hearing protection and again, intentions were positively associated with hearing protection behaviors. Impact on Industry: Our results indicate that appeals to normative influences may be the most effective antecedent to employ when persuading coal miners to wear hearing protection. However, messages designed to impact attitudes and perceived behavioral control were also effective.

Jan 1, 2008

By D. G. Foot

The Bureau of Mines devised a direct flotation method for recovering potash from carnallite (KC1?MgC12?6H20) ore characterized by a high content of water-insoluble impurities. The method includes (1) a decomposition leach of the carnallite, (2) flocculation-depression of the insoluble slimes, (3) potash rougher, cleaner, and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity for removing the water-insoluble slimes by mechanical or flotation de-sliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumption. Locked-cycle testing of the direct flotation method recovered 87.8 pct of the potassium in the flotation feed in a final product containing 60.6 pct K20. A flowsheet incorporating the carnallite leaching-potash flotation procedure is presented.

Jan 1, 1982

By P. R. Tisot

The structural response of propped oil shale fractures was determined for each of two different grades of Green River oil shales (38.0 and 29.0 gpt) as they were heated in an inert atmosphere from ambient to subretorting temperatures (below those required for rapid pyrolysis of the organic matter). Small oil shale cores were propped apart by 3-mm glass beads to simulate a small cross section of a propped oil shale fracture between an injection and a producing well. These specimens were then heated at a uniform bate up to 800° F in a specially designed test cell under stress levels from 100 to 1,000 psi in biaxial and in triaxial confinement. Under the conditions of heat and compressive stress utilized in this study, all of the propped fractures in the two oil shales underwent structural deformation ranging from partial to complete collapse, as evidenced by proppant embedment. Structural collapse of induced fractures would in turn result in serious impairment or complete loss of the fracture flow capacities of the specimens. Results from this Bureau of Mines study indicate that underground retorting of Green River oil shale may be seriously impaired by loss of permeability when utilizing propped fractures in oil shales assaying more than 28 gpt.

Jan 1, 1975

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

By B. J. Scheiner

As part of the goal to maximize minerals and metals recovery from primary domestic resources, design factors associated with minimizing current leakage in bipolar cell configurations were studied by the Bureau of Mines as a means of improving the efficiency of bipolar e1ectrooxidation cells. Initial studies that were conducted in a small bipolar cell operating at 140 to 145 volts and 15.4 amp indicated how design factors could be employed to minimize cur-rent leakage around adjacent electrodes during cell operation. Based on these results, a 40-electrode, 108-kva prototype of an industrial-sized cell was constructed and tested for extracting metal values from offgrade molybdenite concentrates. The feasibility of recovering molybdenum and rhenium from the oxidized pulp also was determined. Feed to the process sequence consisted of flotation concentrates containing 16 to 35 pet Mo as molybdenite and 6 to 15 pct Cu. E1ectrooxidation in the prototype cell resulted in 84 to 97 pct Mo and Re extraction with a corresponding energy consumption of 9 to 13 kwhr/1b Mo extracted.

Jan 1, 1979

By R. E. Hall

When the criterion for control of scale prevention on the evaporating surfaces is made the conditions in the concentrated boiler water, then this control becomes an exact operation amenable to an accuracy commensurate with all other operations in the boiler room. The responsibility in boiler water conditioning, however, includes more than clean surfaces. Corrosion in feed lines, economizers and the boiler is a function of the condition of the later, and must be controlled. Steam line and turbine blading deposits must be obviated by the system of conditioning. By the chemical treatment employed, the amount and character of noncondensable uses in the steam must be controlled in accordance with the intended use of the steam. All. in all, the responsibility in boiler crater conditioning ends not with the entrance of the water into the boiler but with the passage from the boiler nozzle of steam, the dryness and rarity of which are defined by the uses to be made thereof. A clearer conception of the scope of boiler water conditioning can be obtained by reference to a diagram of the surfaces (Figure 1) at which it functions. Consideration of this diagram leads to the following outline for the problems of boiler water conditioning: (a) Prevention of scale formation on surfaces (1) In contact with water but at which no evaporation occurs. (2) At which evaporation is occurring.

Jan 1, 1926