Search Documents

By Jr. Norman

Thermoelectric properties of depleted uranium selenides and tellurides were investigated from room temperature to 700 C. Several depleted uranium monoselenides and monotellurides were doped with selected cationic and anionic materials to determine the effect of impurity additions on the thermoelectric properties. The undoped uranium selenides and tellurides were semimetallic conductors exhibiting low Seebeck coefficients and electrical resistivities. Partial or complete degeneracy was in evidence, indicating a charge carrier energy distribution similar to that in a metal. Doping increased the Seebeck coefficients of the uranium monoselenides and monotellurides; however, the corresponding change in the power factor in the figure of merit was small because of the increase in electrical resistivity.

Jan 1, 1965

By C. W. Owning

"The Bureau of Mines has repeatedly emphasized the necessity of completely ""rock-dusting all coal mines, except anthracite mines, in every part whether in damp or dry condition."" Every open accessible part of, the, mine without exception should be thoroughly rock-dusted, including parallel entries, air courses, trackless entries, crosscuts, and rooms to within at least 40 feet of every coal face. Very few mines have followed this recommendation and warning, with the result that there have been explosions not only in mines which have not used rock dust but also in so-called rock-dusted mines. Following a number of mine explosions it has been reported that the mine was rock-dusted,"" whereas it is probable that only some of the haulage roads had been given a hurried application of rock dust and in most instances not as much as 5 per cent of the mine was really rock-dusted. That is not rock-dusting.Some conscientious, well-meaning mining men have felt that rock-dusting of haulage roads would effectively stop an explosion; however, when shown, through widespread explosions in mines ""well rock-dusted"" according to the above method, that leaving large areas undusted, furnishes paths through which a violent explosion may travel, these mining men have realized the necessity of thorough rock-dusting and have adopted this explosion-prevention method.The Mather Collieries mine, Pickands, Mather and Co., operators, at Mather, Pa., was the first mine in Pennsylvania to receive, full credit for rock-dusting under the new 'stringent ruling of the Pennsylvania Compensation Rating Bureau, the provisions of which require that:"

Feb 1, 1931

By P. L. Woolf

Two blast furnaces, one a. commercial furnace and the other the Bureau of Mines experimental furnace, were successfully operated with extremely low slag volumes. The lowest slag rate obtained on the industrial furnace was 335 pounds per ton of metal. Using the same burden materials a 245-pound slag volume was achieved on the furnace. The coke rate saving and increase in productivity resulting from lowered slag rates are discussed as well as the factors limiting a low slag practice.

Jan 1, 1965

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method's usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987

By Slavoljub D. Maksimovic

At some coal mines, methane gas is released during raise drilling. At the request of the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, the Bureau of Mines conducted ventilation surveys at different raise drill sites to assess various methods of reducing methane concentration. The resulting data indicate that raise drill shaft cavities are ventilated by air compressors, vacuum pumps, auxiliary blower fans, and free intake air from the surface. The compressors, pumps, and fans operate simultaneously or separately. At the bottom of the shaft cavities, ventilation is controlled by regulators and airlocks. Methane is monitored, measured, and periodically sampled on the surface, at the bottom, and at different levels in the shaft cavities. Maximum concentration of 3.5 percent was measured in one shaft in West Virginia. Air velocity down the raise drill shafts is always very low, Maximum recorded air down the drill stem was 3,000 cfm, which can be increased by adding air compressors. The best way to ventilate shaft cavities is through the simultaneous use of air compressors and vacuum pumps. If the methane concentration cannot be reduced with additional compressors, then the inside diameter of the drill rod should be increased, or larger pilot hole drill bits should be used.

Jan 1, 1981

By Nicholas Kyriazi

The Bureau of Mines has been developing breathing and metabolic simulator technology since 1970. Breathing simulation has been widely achieved throughout the world and used in the testing of open-circuit breathing apparatus, but satisfactory metabolism simulation has not been achieved. This situation required that the testing of closed-circuit breathing apparatus, which are the only type used in mines, be done using human test subjects. The goal was a machine that could accurately simulate both the breathing and the metabolic functions of a human being for testing of closed-circuit breathing apparatus. The advantages of using such a machine instead of a human being for testing respiratory protective devices lie in its ability to quantify metabolic input, its repeatability, and the lack of a need to deal with the vagaries of human subjects. This report will describe the breathing and metabolic simulators that have been developed and used by the Bureau over the past 15 yr.

Jan 1, 1986

By Raymond B. Ladoo

[Inquiries are frequently received by the Bureau of Minas relative to occurrence, mining, treatment and utilization of the natural hydrocarbons' such as gilsonite, elaterate, wurtzilite, grahamite, and ozokerite although have been known and used for many years, they are not yet well understood and the amount of recent literature dealing with them as comparatively small. This paper is intended merely to summarize the present knowledge The natural hydrocarbons included in this series are gilsonite, elaterite, wurtzilite, glance pitch, manjak, grahamite, albertite, arid ozokerite and many other minor varieties. With the exception of ozokerite and the other mineral waxes, then all more or less resemble asphalt in that they are dark brown or black bituminous substances of organic origin, generally with a resinous luster. Ozokerite usually light an color with a waxey luster, is closely allied to the others of the series, but is usually considered separately, Unfortunately authorities differ as to nomenclature so that determinations of physical and chemical properties from different sources may riot be readily compared. Abraham Herbert, Asphalts and Allied Substances, 1918, 606 pp. has made one of the most detailed studies of these subjects in recent years, and his classification is used in the main. The following definitions are given by him]

Jan 1, 1920

By N. S. Dalal, X. Shi

"The oxidation of NADPH by vanadate(V) in the presence of glutathione reductase showed typical enzymatic kinetics. The oxidation was inhibited by N-ethylmaleimide, a glutathione reductase inhibitor. Superoxide dismutase had no significant effect on the oxidation, indicating non-involvment of the superoxide radical. The vanadate(V) reduction was found to be a one-electron transfer process. These results suggest a new pathway for vanadate(V) metabolism and a new function of glutathione reductase. Compounds of vanadium(V), such as NaV03 , exert potent toxic effects on a wide variety of biological systems (1-3). Despite intense current activity, however, the biochemical mechanism of vanadate(V) toxicity is still not well understood (1- 14). It is believed that one of the important pathways involves the oxidation (by vanadate(V)) of NAD(P)H (15, 16), but, to our knowledge, there has been no report of the identification of any vanadate(V) reductase. With a view to finding if there exists any vanadate(V) reductase, we have investigated the oxidation of NADPH by vanadate(V) in the presence of glutathione reductase. Glutathione reductase (GSSG-R)2 was selected because our previous studies have shown (17) that GSSG-R can act as a reductase for chromate(VI), which is isoelectronic with vanadate(V). We find that GSSG-R does indeed function as a NADPH-dependent vanadate(V) reductase, thus pointing to a new pathway for the metabolism of vanadate(V), as well as to this property for GSSG-R. MATERIALS AND METHODSSodium metavanadate (NaV03 ), henceforth vanadate, was purchased from Aldrich and its solution was always freshly prepared. The GSSG·R used was from bovine intestinal mucosa and was purchased from Sigma. The oxidation of NADPH was followed photometrically as the decrease in absorbance at 340 nm. The spin trap, 5,5-dimethyl- pyrroline-N-oxide (DMPO), was purchased from Aldrich and used without further purification, since very weak or no spin adduct signal was obtained from the purchased sample when used alone.ESR spectra were obtained at X-band (9.7 GHz) using a Bruker ER200 ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR gaussmeter (Bruker, Model ER035A) and the microwave frequency was measured with a digital frequency counter (Hewlett-Packard, Model 5340A). An ASPECT 2000 computer was used for data storage and analysis. The concentrations given in the figure legends are the final concentrations. All experiments were carried out in the phosphate buffer solution (pH 7.2) and at room temperature."

Jan 1, 1990

By J. E. Matta

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method. Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out-crop will emit low levels of methane gas.

Jan 1, 1977

By Martin H. Stanczyk

Acid leaching of selected copper sulfide minerals, impure copper sulfide flotation concentrates, and a cement copper precipitate at elevated temperatures and pressures was investigated. Copper extractions of 97 to 99 pct were obtained by leaching chalcopyrite and the flotation concentrates with water under oxidizing conditions at 200° C for 30 to 60 min. In tests with bornite, chalcocite,and cement copper, addition of sulfuric acid or pyrite to the autoclave was required to obtain similar copper extractions. The chemistry of leaching copper minerals was studied. It was determined that different copper sulfides altered to covellite as one step in their dissolution.

Jan 1, 1963

By P. L. Woolf, J. P. Morris, E. Foerster, G. R. Zellars

Measurements of vapor pressure can be used to determine the thermodynamic activities of the components of metallic solutions . The determination of activity by this method requires accurate values for the vapor pressure of the pure component and for its partial pressure above the alloy solution . This investigation was conducted to measure the vapor pressure of liquid manganese for use in future studies of the activity of manganese in various liquid alloys . In related investigations in the Bureau's Pyrometallurgy Laboratory , vapor pressures of copper , iron and nickel have been measured and activit 4 5 6 have been determined in the iron- copper and iron- nickel systems . Difficulties were experienced with manganese which were not encountered in the previous investigations . Manganese oxidizes readily and greater care was needed to maintain an oxygen- and moisture - free atmosphere in the furnace . In addition , liquid manganese wet the refractories and there was a tendency to foam and splash on introduction of the carrier gas . Because of these difficulties several variations in the experimental procedure were studied . These were first tested with silver which has a vapor pressure of the same order of magnitude as manganese but is relatively inert at high temperatures . Although no significant changes in the original procedure resulted from this work, considerable data were obtained for silver and have been included in this report . Bauer and BBrruunnnneerr7/ have reported the only extensive investigation of the vapor pressure of liquid manganese . However , their results are not consistent with the data obtained by McCabe and Hudson for solid manganese . Measurements of the vapor pressure of silver have been reported by McCabe and Birchenal1,2/ Schadel and Birchenall , 10/ Harteck , 11 / Fischer , 12/ and von Wartenberg.13 / Generally , these investigators conducted their measurements at lower temperatures than were used in this study .

Jul 1, 1960

By C. J. Chindgren

Two air classification systems were built and tested as separatory devices for recovering the nonferrous metal values from shredded automotive nonmagnetic reject scrap. A horizontal air system with a capacity up to 16 tons per hour was used to obtain preliminary separations, and a smaller capacity vertical system was used as a cleaning device. Shredded automobile reject material containing aluminum, copper, and zinc values of about $55 per ton were air-classified in the horizontal elutriator. Ninety-six percent of the metal was recovered in a 74-percent metal concentrate. Tandem operation of both classifiers recovered 92 percent of the metal in an 80-percent concentrate while rejecting 87 percent of the nonmetallics. Heavy media separation of the air-classified concentrate produced an overall recovery of 91 percent of the metal in the form of a 99-percent metal concentrate.

Jan 1, 1971

By N. S. Dalal, X. Shi

"It has been recently suggested that the exceptionally high antitumor and antibacterial activity of natural fredericamycin A (FMA) is related to its ability to spontaneously generate the superoxide anion (02-) and hydroxyl (""OH) radicals in aerobic solutions [Hilton, B. D., Misra, R., & Zweier, J. L. (1986) Biochemistry 25, 5533]. With a view to understand the mechanistic details, attempts were made to reproduce earlier electron spin resonance (ESR) evidence for the oxygenated free radical formation in well-aerated solutions of natural FMA in dimethyl sulfoxide and dilute H 20 2• Little or no evidence was obtained for the formation of the 0 2- and methoxy (""OCH3) radicals, while the detected formation of the 'OH and methyl ('CH3) radicals was attributable largely to mechanisms not involving FMA. These results thus reopen the T question regarding the mechanism of its exceptionally high tumoricidal-bacteriocidal activity. This paper reports on an electron spin resonance (ESR) investigation of the formation of oxygenated free radicals in solutions of natural fredericamycin A (abbreviated as FMA) which has recently been reported to be a highly potent anti¬tumor antibiotic (Pandey et al., 1981; Warnick-Pickle et al., 1981). The impetus for this undertaking was provided by recent reports (Hilton et al., 1986; Stinson, 1986) suggesting that the strong tumoricidal activity with high therapeutic—toxic index of FMA was related to its ability for the spontaneous generation of superoxide anion (02-) and hydroxyl (OH) radicals. For example, the suggested mechanism for the formation of 02- by FMA was (Hilton et al., 1986)FMA-OH + O2 FMA-O + H+ + 02-Here FMA—OH is simply the FMA molecule emphasizing the —OH moiety which becomes FMA-O, the free radical rep¬resenting the oxidized form of the drug. While some other highly effective anticancer drugs in current clinical application, such as bleomycin, are also thought to exert their antitumor effects via the formation of reactive drug-based or oxygenated free radicals (Carmichael et al., 1985; Gianni et al., 1983), FMA was considered unique in that only in this case the free radical formation was thought to be spontaneous, rather than through a metal- or an enzyme-activated process (Hilton et al., 1986; Stinson, 1986). Thus it was suggested (Hilton et al., 1986; Stinson, 1986) that FMA could be the forerunner of a new class of anticancer drugs. However, we noted that while the hypothesis seemed plausible, the reported ESR spectral evidence appeared to be ambiguous. Because of the high significance of the earlier conclusions (Stinson, 1986), we undertook a systematic ESR study of the radical formation in FMA solutions, and as discussed below, our conclusions disagree with those reported earlier."

Jan 1, 1989

By A. E. Nagel, J. E. Carpetta, M. G. Zabetakis, T. D. Moore

The method of moving averages was found useful in assessing the nature of methane emission in coal mines. Emission rates were influenced markedly by the presence of abandoned oil and gas wells in the vicinity of the mine. Such wells appeared to increase the flow rate of methane into the mine by a factor of 2 to 30 in an active mine in the Pittsburgh coal seam.

Jan 1, 1972

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines-developed induction slag melting process is of concern to the titanium industry. The objective of the research was to determine the effect of removing the nonconductive molten calcium fluoride (CaF2) slag used as an insulator between the titanium and the segmented copper crucible. The data were obtained from single-induction-melted ingots prepared with no CaF2 insulating slag and an ingot prepared with the normal addition of 4 pct CaP2 slag. The results showed that the mechanical properties of single-induction-slag-melted and annealed Ti-6AI-4V alloy exceed the minimum values specified in "Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H." High-cycle, tension-tension fatigue testing yielded similar results. The data from 44 of the 45 specimens were contained within the typical scatter band for fatigue data on wrought Ti-6AI-4V alloy. Although the removal of the insulating slag is a desirable change, the data from the specimens with the previously standard 4 pct slag addition showed no detrimental effect from the slag inclusions.

Jan 1, 1988

By Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion-proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures,a multi compartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 2010

By R. V. Ramani, R. Bhaskar

"The results .of an experimental and theoretical research study into the spatial and .temporal behavior of dust in mine airways is summarized in the paper. Experiments were performed in mine airways under both controlled and .normal operating conditions. The controlled experiments included the documentation of the concentration and deposition patterns for two types of dust under three different velocities. Real-time dust concentration data were obtained using Real-time Aerosol Monitors (RAM-1) to determine the dispersion coefficient in a mine airway. On the theoretical front, a convection diffusion model of the dust flow phenomenon in mine airways was developed considering dominant mechanisms affecting dust transport and deposition in mine airways. Mechanisms modeled include turbulent and gravitational deposition, coagulation, and dispersion.In this paper, comparative analyses of results of the controlled experiments with the predictions of the mathematical model are presented. In addition to the overall validity, the adequacy of the individual components of the model, such as deposition in the total and respirable range, and dispersion are examined in light of the experimental observations.The experimental data from controlled experiments compared more favorably with model predicted results for similar conditions as opposed to the ·comparative analysis results for in-mine experiments. Specifically, the model· predictions for an 800-meter stretch of a mine airway reveal some significant differences from the behavior noticed in the mine. The deposition was lower than that predicted by the model. Consequently, concentrations were higher than those predicted by the model. The implications of these and other findings for further investigations are discussed in the paper."

Aug 31, 1989

By Leroy Dockter

The grinding characteristics of lignite in a ball mill were investigated. The variables studied were initial lignite moisture content, degree of in-the-mill drying, and lignite source. The mill tested was a pilot-p1ant-size conical ball mill which had a maximum output of from 80 to 180 lb/hr pulverized product depending on the lignite and test conditions. The capacity of the test mill ranged from 82 to 103 lb/hr depending upon mine source, in pulverization of as-mined lignite with minimum drying, The capabilities of the ball mill could not be correlated to Hardgrove index of the individual lignites or other observed physical properties. Predrying lignite from its 35 to 40 percent raw moisture content to about 10 percent moisture before grinding improved the mill capacity 87 percent, compared to an increase in capacity of 74 percent with in-the-mi11 drying to the same product moisture.

Jan 1, 1967

By R. H. Jefferson

This Bureau of Mines report describes a series of rapid wet chemical methods for the analysis of blast furnace slags. A "complete" analysis for total iron, manganese, silica, lime (calcium oxide), magnesia (magnesium oxide), sulfur, and mixed oxides (R203) can be routinely performed in less than 3 hours. These methods were employed as the analytical control procedures for the Bureau's experimental blast furnace operations and have been satisfactorily applied to the analysis of other slags and calcareous materials.

Jan 1, 1974

By George C. Branner

This study was planned to present salient facts of the California and Nevada sulfur industries and to indicate existing opportunities for increased economic utilization of California and Nevada sulfur resources. Numerous publications on sulfur have been issued by the Federal Bureau of Mines, including Information Circular 6329, Sulfur, by Robert H. Ridgway (1930); annual Minerals Yearbook chapters on Sulfur and Pyrites, by various authors; and a chapter on Sulfur by G. W. Josephson in Bureau of Mines Bulletin 556, Mineral Pacts and Problems (1956). This literature, however, deals primarily with the national and international sulfur situation and does not attempt to analyze the possibilities for increased economic development of sulfur resources by individual States. The present study attempts to analyze these possibilities in California and Nevada and to (1) evaluate factors that have influenced production and consumption in California and Nevada and (2) indicate apparent trends in production, consumption, and prices in these States.

Jan 1, 1959