Search Documents

By George F. Dana

Oil yields, lithology, and stratigraphy have been evaluated for 15 cored wells and two sampled wells representing 10 square miles of the Tipton Member of the Green River Formation near Green River, Wyo. The area evaluated is being used by the Bureau of Mines for experimental production of oil from the oil shales in place. Lithology and oil yields were correlated to produce a stratigraphy diagram for the in situ study area, permitting precise designation of comparable sections. Because of lateral uniformity of oil shale, oil yields from eight cores and two sets of drill-cutting samples within a quarter section show the range of variation in average oil yield arising from experimental error. Variation in average oil yields from the seven cores representing the 10-square-mile study area lies within the expected experimental error. No difference in oil-shale richness across the study area is indicated. Average oil yields for three Tipton sections in the study area were deter-mined as follows: (1) The entire Tipton Member oil shale (about 145 feet thick), 13.3 gallons per ton; (2) the 40-foot upper rich zone, 21.0 gallons per ton; and (3) the 21-foot zone in which the Laramie Energy Research Center is conducting in situ experiments, 22.4 gallons per ton. One acre of the 21-foot experimental section represents 34,300 barrels of oil in place, and 1 acre of the Tipton's 40-foot rich upper layer represents 62,000 barrels.

Jan 1, 1972

By Bruce D. Hanson

The Bureau of Mines conducted a series of experiments using four different coal types to determine the effect of attack angle and symmetric bit wear on airborne respirable dust (ARD) generated by point-attack bits and in energy consumption. Neither had a significant effect on ARD at the 95-pct confidence level, but bit wear had a significant effect (95 pct confidence) on specific energy (energy per gram of cut coal) for three coal types, Depth of cut was the most significant factor affecting ARD and specific energy.

Jan 1, 1979

By Hiram C. Draper

The Mining Division of the Bureau of Mines, in cooperation with the Obstacle and Demolition Branch, Engineer Research and Development Laboratories, Department of the Army, undertook some extensive tests to determine the effectiveness and limitations of using standard demolition-type shaped charges in underground Mining. The tests proved the shaped charge has no practical application in the functions of mining covered by this report. At an approximate cost of 0 per foot hole plus spall produced by the most efficient single shots with the M3 shaped charge, the cost is over 20 times that of producing a better hole with a rock drill. The concussion would prohibit its use in many mines, and the excess carbon monoxide gas liberated by the pontolite explosive would be an additional hazard when used underground.

Jan 1, 1948

By Sol Weller

The Fischer-Tropsch synthesis consists of the formation of long-chain hydrocarbons by passage of carbon monoxide-hydrogen mixtures over metal catalysts, usually based on iron, cobalt, nickel, or ruthenium, at temperatures in the range 180°-300° C., and at pressures of 1-15 atmospheres. Although the reaction has been known and studied for more than 20 years, the mechanism by which it occurs is still poorly understood. One approach to understanding is to consider the effect upon the course of the synthesis of variations in each of the important operating variables. Consideration of the experimental data pertaining to these variables may suggest an over-all picture describing the synthesis - a picture which, in turn, would have to be consistent with all the known facts. The first part of this paper will be concerned with such a consideration of operating variables; the second portion will discuss recent work pertaining to the role of metal carbides as intermediates in the synthesis.

Jan 1, 1949

By L. L. Oden

The Bureau of Mines has studied a number of processes to remove Cu from molten steel scrap with the objective of determining if any of the laboratory methods studied warranted in depth research investigations. Experimental approaches included oxidizing Cu from steel containing other metals that form stable mixed oxides with Cu (AI, Cr, Fe, Mn, Mo, and V), injecting the same metals as oxides to simplify the mechanism of complex oxide formation, partitioning Cu into alkali or alkaline earth silicate slags or oxide-moderated sulfides, and coremoving Cu and S by injecting active compounds of Ca and Mg. The most promising tests, producing nearly 0.3 pct Cu in the slag, used Ar injection of K20-moderated Na2S-FeS below the surface of molten steel containing about 0.6 pct Cu and protected by a CaO-SiOz slag; however, in depth research investigations currently are not felt to be warranted.

Jan 1, 1987

By W. D. Musgrove, B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Cahaba coal field is the second largest coal—producing area in Alabama. This field underlies parts of Shelby, Jefferson, St. Clair, and Bibb Counties and has an area of about 270 square miles. The Cahaba formations contain a number of coal beds, about 8 of which are mined at present. Although the area contains many folds and faults, samples from various mines and beds indicate that, except for the variation in ash content, the coal from this field is very uniform in character and quality. It is a high-volatile bituminous coal used chiefly for steam-raising purposes and domestic fuel. The coal as mined usually contains too high a percentage of impurities to be marketed without some preparation. The majority of the mines have washing plants in which jigs are the favorite type of equipment, although at some mines tables are used for cleaning the slack sizes. The washing characteristics of the coal from the Cahaba field are very uniform and differ from those of the near-by Warrior field, in that the coarser sizes contain a much lower percentage of bony material than the finer sizes. In general, the bone increases with decrease in size. It breaks into thin flakes, making difficult its elimination in the cleaning process, and gives rise to what is known among the washery operators of the Cahaba field as the ""rash problem.""A previous publication 5 referred to rash from the standpoint of jig operation and suggested some means of handling it with jigs. This report presents the results of table tests on two samples of fine coal from the Thompson and Woodstock beds, respectively, of the Cahaba field to determine the influence of rash on table efficiency.This investigation has been made in connection with the study of coal-washing problems now being conducted by the U.S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators of Alabama."

May 1, 1934

By L. W. Kelly

The primary purpose of this paper is to show the appreciable savings that were made by roof-bolting the main west entry of the Kings mine, which was to be the permanent, main haulage road, as compared to the cost of supporting the same roof with peg timbering as first planned. Additional items that might prove valuable to other mine operators are contained in this paper and detailed below. 1. A detailed cost of the system of roof support known locally as the peg-timbering method is given. It consists fundamentally of supporting steel cross bars on pegs inserted into holes drilled in the ribs close to the roof. 2. A method of supporting the roof in caved entries is shown, where such support must endure for an extended period in haulageways and air courses.

Jan 1, 1952

By Raymond P. Maloney

The Bureau of Mines investigated the White Mountain mercury deposit, in the Kuskokwim River Basin, to better determine the extent of mercury mineralization and to encourage its development by private industry. A program of diamond drilling, augering, bulldozer trenching, and sampling was carried on during four field seasons, from 1960 to 1963, inclusive. Significant amounts of cinnabar, with only trace amounts of arsenic and antimony, occur in dolomite over an area about 4,000 feet long and 1,500 feet wide. The deposit differs from other mercury deposits in the Kuskokwim River Basin by the absence of silica-carbonate and rhyolite intrusives. Small-scale mining was started in 1963 as the result of Bureau investigation and continued during the summers of 1964 and 1965. The investigations indicate that open pit mining might be the most feasible method of working this deposit.

Jan 1, 1967

By Robert L. Jones

The Boston Consolidated mine is situated in the Bingham mining district, Salt Lake County; Utah (fig. 1). The property has had a noteworthy production of cupriferous, gold-bearing, pyritic ore in addition to lead ore. The Bureau of Mines established a diamond-drilling development project on the property in September 1943 with the primary objective of determining the continuity of a mineralized zone in the Commercial limestone below and to the northeast of the 800-foot level (fig.2). Examination of the geologic feature at the property previous to drilling indicated that the mineralized limestone horizon would continue belay the 800-foot level, but with a flatter dip than disclosed above this level. During the project period, 36 holes totaling 4,001 feet were drilled from underground stations outlining the zone below the 800-foot level (figs. 2 and 3).

Jan 1, 1949

From time to time the Bureau of Mines has interpreted and applied certain provisions of the Federal Coal Mine Safety Act and Federal Mine Safety Codes, primarily for the guidance of Federal Coal Mine Inspectors. Although interpretations of the Act have appeared in the Federal Register, the Code interpretations and practical applications have not been published. In response to many requests from representatives of the coal-mining industry, the Bureau is publishing this information to promote better understanding of those provisions that may be misinterpreted or misapplied. INTERPRETATIONS AND APPLICATIONS Two Federal Mine Safety Codes are discussed in this report, namely the Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States, Part 1, and the Federal Mine Safety Code, Anthracite Mines of the United States, Part 1. In this circular the word Codes refers to both directives; Code* refers to the code for bituminous-coal and lignite mines; Code? refers to the one for anthracite mines. Act* refers only to bituminous-coal and lignite mines.

Jan 1, 1963

By Raymond M. Stateham

Calculations based on data obtained from measurements of smoke from coal-fired powerplants predict that infrared imagers will be useful tools for smoke vision. Infrared imagers operating in the 3-to 5-um spectral region have been evaluated for this purpose. A mine opening 110 meters long was filled with smoke from burning coal, and two men, wearing breathing apparatuses, moved through the smoke to serve as targets. The men were detected and identified at 80 meters.

Jan 1, 1976

By T. J. Ballard

The Conrad Hill mine vas first opened as a gold mine about 182 and has been operated at various times since then. The Bureau of Mines, as part of the strategic minerals program, mapped and sampled the accessible mine workings. The work failed to reveal appreciable copper values or evidence of additional ore deposits.

Jan 1, 1948

By Wilbur Duvall

For the past few years the Applied Physics Branch has been investigating, experimentally, the generation and propagation of strain waves in rock. The strain waves are produced by the detonation of a high-velocity explosive placed in a small cavity in the rock. Strain gages mounted in the solid rock surrounding the cavity record the strain pulses propagated away from the source. Numerous strain-wave pulses have been recorded in different rock types for charges of various sizes and at various distances from the charge. Analysis of these records has shown, among other things, that there is associated with the strain wave a characteristic pulse width. This pulse width is dependent on the rock type and the distance from the shot point to the gage, but is apparently independent of the charge size or cavity size. Recent published literature on the generation and propagation of seismic waves indicates that the characteristic frequency of an elastic wave generated by an explosion should be a function of the rock type and the size of the cavity created by the explosion. Also, internal friction in the rock would produce absorption of high-frequency components, which would cause continual change in the shape of the pulse propagated. As the experimental data did not verify the expected change in pulse shape with cavity size, a theoretical investigation of the vibrations associated with a spherical cavity in an elastic medium was undertaken.

Jan 1, 1950

By J. M. Mutmansky

"This study analyzed laboratory comminution techniques for respirable mine dust generation and the properties of the resulting dusts. It was the objective of the study to determine the suitability of the resulting dusts in reflecting the properties of natural airborne dust. This paper deals specifically with the amount of contamination introduced into the generated dust as a result of abrasion when using nine different grinding methods. The analysis was made by comparing the content of 25 chemical elements in the lab-generated dusts with the same elements in the airborne coal mine dusts. It was found that all the lab-generated dusts possessed contamination but that several methods produced smaller percentages of contamination and that the residence time in the grinding device was an important factor in the contamination levels. INTRODUCTIONDust in the atmosphere is a health hazard and a major source of occupational diseases in the coal mining industry (Anon., 1980; Merchant, Boehlecke, and Picket-Hamer, 1986). It has been shown that coal workers' pneumoconiosis (CWP) is directly related to the inhalation and accumulation of respirable coal dust in coal miners' lungs. In order to effectively protect coal workers from coal dusts, we must have a clear understanding of dust properties including dust generation and dust-lung reaction mechanisms. This requires extensive biomedical research. Dust related research often requires large samples of respirable coal dusts to be collected, either for repeated experiments or stored for future reference. Unfortunately, current sampling instruments are not able to meet this demand. Ali a result, laboratory-generated coal dust ls frequently used as a substitute for coal mine dust in biomedical and other research applications. Now, the questions are how close the characteristics of laboratory-generated dusts are to those of mining-generated dusts and which equipment is moat appropriate for research dust production in the laboratory . These are some of the interests of this research project. The primary objective of this project was to find a laboratory technique which can generate coal dusts possessing properties similar to coal mine dust with respect to particle size distribution, chemical composition, and particle shape and morphology. However, this paper will focus only on the chemical compositions of the prepared dust samples and try to identify the sources of chemical contamination from various size reduction processes."

Mar 1, 1992

By J. W. Miller

Depletion of coals most suitable for metallurgical fuel has nude necessary a general survey of coking-coal reserves in the United States. These investigations were begun in 1948 at the joint request of the Munitions Board, Department of Defense, and a number of coal companies. This report, which is one of a series, by counties, describes the preparation characteristics of the coals of Letcher County, Icy. From these data it is possible to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are suitable under present standards for producing metallurgical coke, (b) which coals require special and more intensive treatment in preparation than is now practiced, and, (c) which coals cannot be upgraded by known commercial preparation methods to metallurgical fuel standards now accepted.

Jan 1, 1955

By E. R. Palowitch, A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high - sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations . The survey , which provided information on Appalachian region coals only , indicated that such important coalbeds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14 - mesh top size . For many other coalbeds amenability to sulfur liberation by crushing was indicated , although too few samples were available to draw firm conclusions .

Jan 1, 1966

By L. C. IlsLey

Through the cooperation of the Pennsylvania Department of Mines the writer obtained from State, records detailed information concerning coal-mine accidents occurring in Pennsylvania bituminous mines during 1939, particularly those nonfatal accidents in which the injured person lost 60 or more days? time from mark. The writer wishes to acknowledge assistance received from Pennsylvania State officials, especially Richard Maize, secretary of mines, and. Joseph J, Walsh, deputy secretary of mines; also to Thomas Dickinson,3/ of the Bureau of Mines, who rendered valuable assistance in assembling the data an the several tables.

Jan 1, 1941

By E. S. Shedd

The Bureau of Mines investigated electrowinning and tapping lanthanum metal from lanthanum oxide in a fluoride bath. The electrolyte was composed of LaF3, BaF2, and LiF. Metal containing 0.2 percent impurities was produced at a rate of over 2 pounds per hour. Principal impurities were carbon, aluminum, and silicon. Low-carbon metal was produced by continually discharging the carbon oxide gases and maintaining 0.1-atmosphere pressure. Anode reactions and cell design were found to be important factors in cell operation. Both frozen electrolyte skulls and tungsten metal crucibles proved satisfactory for collecting the metal and did not react with the molten lanthanum.

Jan 1, 1966

By R. R. Wells

As a part of the strategic minerals program of the Bureau of Mines, nine chromite-ore samples were obtained during the period 1949-56 from mines in the vicinity of Red Mountain, near Seldovia, Kenai Peninsula, Alaska. This report summarizes the results of beneficiation studies of the samples at the Bureau's Juneau, Alaska, and Albany, Oreg., laboratories. In general, the ores were found amenable to concentration by gravity methods for producing concentrates that assayed over 48 percent chromic oxide. Intimate association of chromite and gangue minerals, however, necessitated fine grinding and limited the amount of chromite recoverable. Recovery of chromium in concentrate that assayed 48 percent chromic oxide or higher ranged from approximately 20 percent for low-grade ores (10 to 12 percent Cr203) to more than 95 percent for 1 high-grade sample (42 percent Cr203). The iron content of the chrome-bearing mineral -hence, the chrome/iron ratio of finished concentrate -appears to vary with the grade of the ore. Concentrates made from high-grade ores had chrome/iron ratios as high as 3.1:1; the concentrates from low-grade ores, however, had chrome/iron ratios as low as 1.8:1.

Jan 1, 1957

By A. D. Hahn

The Federal Bureau of Mines examined ilmenite-bearing sands in southern Texas as part of a program to discover sources of supply for the domestic titanium industry. Deposits were examined from May 1956 through January 1959 in the outcrops of sandstone beds in the Jackson group of Eocene formations in Lee, Burleson, Fayette, and Starr Counties on the Gulf Coastal Plain; in alluvial valley fill in Brewster County in southwest Texas; in the sand beaches of Matagorda Peninsula and the Galveston, Padre, and Brazos Islands--part of the offshore chain of barrier islands along the Texas coast; and in unconsolidated sediments in Willacy County on the Rio Grande delta in the southeast Texas.

Jan 1, 1961