Search Documents

By J. P. McGee

As part of a joint U.S. Atomic Energy Commission-Federal Bureau of Mines program for using nuclear energy to supply process heat, a simulated nuclear loop has been constructed to test components. This loop has been operated for more than 1,800 hours at 100 p.s.i.g. Of this period, 23 hours were at 2,500° F. and higher; 540 at 2,000° to 2,500° F.; 840 at 1,500° to 2,000° F.; 200 at 1,000° to 1,500° F.; and 260 below 1,000° F. Leakage at flanges and welds was not a serious problem. A helium-recycle system with gas temperatures of 2,300° to 2,500° F. and a static pressure of 250 p.s.i.g. appears feasible. Difficulties were encountered with the recycle compressor due to thermal distortion of the impeller and shaft. The use of sealed bearings limits compressor operation to the life of the bearings.

Jan 1, 1960

By P. M. Sullivan

At its College Park Metallurgy Research Center in Maryland, the Bureau of Mines has installed and is operating a 5-ton-per-hour pilot plant for continuous mechanical separation of values contained in raw urban refuse. The entire sys tern was assembled using commercially available equipment. The process relies on multistage processing including shredding, air classification, screening, gravity concentration, and electrostatic separation. Compactor trucks deliver raw refuse collected along typical routes in metropolitan Washington, D.C., to the pilot plant. The loads are separated into concentrates of (1) light-gage iron, (2) massive metals, (3) glass, (4) putrescibles and waste combustibles, (5) paper, and (6) plastics. While some refinements remain to be made in the processing system flow-sheet, the data obtained to date have been highly encouraging, indicating favorable economics for commercial-size plants.

Jan 1, 1973

By W. P. Haynes

The Bureau of Mines has been studying a modified steam-iron process using coal-derived producer gas for making either hydrogen plus carbon monoxide or methane. To provide a guide for this experimental study, compositions of equilibrium product gases for the reaction of steam plus carbon dioxide with iron were calculated and are discussed in this report. The calculations, which are described in this report, are based on thermodynamic data in the literature and cover temperatures from 800° to 1,300° K., pressures from 1 to 30 atmospheres, and hydrogen-to-carbon atomic ratios in the gas of 4 to 12. The equilibrium gas compositions are discussed in regard to making hydro-gen, carbon monoxide, and methane in the oxidation step of the modified steam-iron process. From the viewpoint of thermodynamics alone, assuming the reactions reach equilibrium, the discussion considers the effects of temperature, pressure, and composition of feed gas upon the composition of the product gas, the degree of oxidation of the iron, and the possible deposition of carbon. The results indicated the following: (1) Nearly all the carbon can be converted to methane at low temperatures (800° to 900° K.) and high pressures (over 20 atmospheres); (2) to obtain high yields of synthesis gas, high temperatures are required. For example, at 30 atmospheres, a temperature over 1,200° K. is required to convert 60 percent of the steam plus carbon dioxide to hydrogen plus carbon monoxide. Lower temperatures may be used at lower pressures) (3) oxidation of the iron increases with increasing pressure and decreases with increasing temperature; and (4) process conditions favoring carbon deposition were found within the range of variables studied, but it is thermodynamically possible to operate the oxidation process with steam and carbon dioxide outside this range of carbon deposition.

Jan 1, 1961

By Syd S. Peng

The design of retort interchamber pillars is important in determining surface stability over in situ retort mines and to the health and safety of miners, particularly with respect to possible escape of heat and toxic gases from retort chambers. Stress distribution in retort interchamber pillars, roof, and floor was examined with the aid of linear, finite-element analysis using data from experimentally determined mechanical properties. Properties determined included elastic moduli, strength, and creep constants in laboratory tests on core covering a 100-foot depth interval in the oil shale from the Piceance Basin in Colorado. The most critical stress concentration was found in the rib side of the interchamber pillar at a height above the floor line of 1.25 times the width. Guidelines for pillar design that consider pillar strength, creep, and retorting temperature effects are proposed.

Jan 1, 1981

By Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average Sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining.

Jan 1, 2010

By W. T. Abel

The Bureau of Mines tested 48 materials for their ability to absorb H2S from hot simulated producer gas (1,000°-1,500° F). The material found best from the standpoint of absorption capacity, durability, and amenability to regeneration was sintered pellets of 75 percent fly ash-25 percent Fe203. The performance of this absorbent under simulated and actual conditions is described. The effect of absorbent composition, absorbent temperature, steam content of the gas, and tar vapors and dust in producer gas is discussed.

Jan 1, 1974

By G. E. Rennick

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 1/2 part per billion. Expandable cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jan 1, 1972

By A. L. Engel

This publication describes further research by the Federal Bureau of Mines in beneficiating domestic manganese ores. The ores selected for treatment were typical of many manganese deposits in California and Nevada in that they have not been economical to mine because they are low grade or contaminated with siliceous minerals and are not amenable to physical concentration.3 4/ It would be desirable to develop a simple treatment method resulting in nearly complete extraction of manganese from these ores and applicable to small-scale operations. Sulfation reduction appeared to be such a method. The studies reported in this publication were directed toward sawdust or lignin-sulfonates as reducing agents. Sawdust, as waste from lumbering, and lignin-sulfonates, byproducts of woodpulp papermaking, are comparatively cheap and may be available in areas where manganese ores are found. Sugar, oils, and coal were also tried as reducing agents.

Jan 1, 1960

By Jack C. White

As part of an investigation of the production of alumina by the nitric acid leaching of kaolinitic clay, the Bureau of Mines designed, built, and tested a fluidized-bed system for the calcination of aluminum nitrate nonahydrate to alumina, while recovering nitric acid. The calciner consisted of an 8-in-square by 36-in-tall vessel containing 18 in of fluidized solids. Molten aluminum nitrate, sprayed directly into the fluidized solids, formed sandy, granular alumina by growth of successive layers on fluidized particles. Solids were fluidized in a dense bed at temperatures of 250° to 500° C with steam, air, or mixtures thereof. Decomposition of nitrate ranged from 4 to 10 pet during single-pass steam or air fluidization, respectively. Alumina dust losses and low throughput are significant unsolved problem areas.

Jan 1, 1982

By T. E. Gray

This report describes the preparation characteristics of the most significant coal beds in Wise County, Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Wise County produced approximately 6,600,000 tons of coal in 1955, of which about 2,110,000 tons was cleaned mechanically. The Federal Geological Survey has estimated that 1,341 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By W. W. Odell

"It has long been recognized that coke is a more desirable fuel than bituminous coal in water-gas apparatus of present design, but still considerable headway has been made in the use of the latter fuel as a substiaute for coke. This is particularly true in the Central States where the supply of high-grade coke has been very limited and uncertain during the past few years, and where coking coals of low sulphur content were available in quan¬tities. In fact, with, the present difference in price of coal and coke, it is possible to realize a marked saving when using a coking bituminous coal as generator fuel.Difficulties have been encountered in the use of such fuel, but they have, to a large extent, been overcome. One of the chief obstacles in the use of the more general utilization of bituminous coal for water-gas manufacture, is the fact that, with normal operation, the capacity per unit of time is reduced. This of course is a serious problem for plants operat¬ing at capacity with coke fuel. However, this difficulty can, to a large extent, be remedied by a changed method of operating, and can be entirely remedied by a combination of the latter with a change in the design (or proportions) of a water-gas set. The preceding statement, the reader will understand, refers more particularly to a carburetted water-gas set.In the manufacture of water gas from coke, present practice requires that for continuous 24-hour service the heat of combustion of all the carbon monoxide (CO) generated during the air blow be utilized in addition to the sensible heat of the gas coming from the generator. This is doubly true when making carburetted water gas from bituminous coking coal. The reasons why this is so are apparent when the following factors are considered."

Nov 1, 1920

By Richard G. Sandberg

Sphalerite concentrates prepared during processing of Missouri lead ores contain small percentages of cobalt and nickel which adversely affect zinc electrolysis. The Bureau of Mines has evaluated solvent extraction and precipitation techniques to remove and recover cobalt and nickel from zinc sulfate solution prior to zinc electrolysis. Prepared zinc sulfate solutions containing about 190 gpl of zinc and 50 ppm of both cobalt and nickel were treated using various combinations of complexing reagents, solvent, pH, concentration, time, and temperature. The following complexing reagents gave the best results: a-nitroso-ß-naphthol, ß-nitroso-a-naphthol, 1,2 cyclohexane dione dioxime (nioxime), di-2-pyridyl ketone oxime, and dimethylglyoxime. These reagents in suitable solvents lowered the cobalt and nickel levels to <0.1 ppm. Stripping the complexed reagents from the solvents was not possible except for nioxime. Direct addition of the appropriate reagent to the prepared zinc sulfate solution resulted in the precipitation of cobalt and nickel. Several possible flowsheets are presented for the removal and recovery of cobalt and nickel. Good zinc deposits were successfully electrowon from zinc sulfate solutions purified by solvent extraction and precipitation.

Jan 1, 1978

By R. H. Sprute

This report describes Bureau of Mines laboratory test results in electro-kinetic dewatering and consolidation of metal-mine mill tailings from five mines in the Coeur d&apos;Alene, Idaho, district. Classified (coarse) tailings, slimes, and unclassified material were separately tested. Tailings were placed in 0.3 ft3 plexiglass models, and dc potential was applied until dewatering ceased. Time-oriented measurements of water removal, changes in resistivity, and power consumption were recorded during the dewatering process. Moisture content and density of the dewatered material at test end indicated the method to be generally effective for all materials examined, but best results were achieved with well-mixed unclassified tailings.

Jan 1, 1974

By Donald P. Blasko

The first well that produced commercial quantities of oil in the Cook Inlet Basin of Alaska was completed in 1957. Since that time oil production in the basin has increased rapidly and by the end of 1969 had reached an annual rate of 74 million barrels. Five major oilfields had been developed, and two additional discoveries awaited development. Estimated amounts of recoverable oil by primary and secondary recovery methods total 2.7 billion barrels, or 36 percent of the estimated oil originally in place. Repressurization by injecting gas or water in formations containing undersaturated oil has significantly increased the volume of recoverable oil. All production has been from formations of the Tertiary age; that much of it is from depths of 10,000 feet or more is unusual for Tertiary formations. The oils are low in sulfur and contain low to moderate amounts of asphalt.

Jan 1, 1972

By Harry K. James

Experimental studies of the physical and explosion characteristics of pure hydrazine nitrate and multicomponent systems containing hydrazine nitrate, supplemented with an extensive Literature survey, are presented. Such proper- ties as melting point, heat of fusion, density, viscosity, surface tension, thermal stability, decomposition process, detonation velocity, impact sensitivity, and TNT equivalence are included.

Jan 1, 1970

By Edward W. Parsons

The explosive-anchored rockbolt was field tested in six mines where rock conditions varied from incompetent shale or mudstone through fairly soft sand-stone to firm sandy shales. The purpose of the testing was to document, under a wide variety of conditions and in comparison to other rockbolt anchors, the quality of the anchorage produced by the explosive-anchored bolt. In addition, the length, strength, and design of the explosive charge necessary to produce positive anchorage up to the yield strength of the weakest component of the bolt were determined. A l4-inch length beaded explosive charge was found to be suitable, in general, in relatively weak strata, and the length can be reduced in more competent strata. Of the 127 explosive?-anchored bolts tested, 118 bolts produced an evaluated anchorage in excess of 17,000 pounds. Only 4 of 43 expansion-shell bolts and 4 of 14 wedge bolts produced anchorage this good. In preliminary tests, properly coupled explosive-anchored bolts did not ignite an explosive gas mixture. Some minor phases included in the investigation were as follows: (1) effect of explosive-anchored rockbolt on surrounding rock; (2) effect of time on anchored bolts based on torque tests; (3) effect of submersion in water on rockbolt anchorage; (4) pull tests to higher loads; and (5) ignition tests.

Jan 1, 1965

By J. S. Dunning

The Bureau of Mines investigated a series of Fe-Al-Mo alloys strengthened by ZrC (zirconium carbide) precipitates as chromium-free substitutes for stainless steels. Melting and fabrication methods were devised, and the effects of minor additions of columbium (niobium) and cerium on the mechanical properties and oxidation resistance were determined. Zirconium carbides could not be con-trolled reliably to produce fine precipitate dispersions. A more reliable carbide strengthening mechanism is required if the high-temperature strengths of types 304 and 316 stainless steels are to be duplicated. Workability and oxidation resistance of the alloy series were excellent.

Jan 1, 1982

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924

By Charles Vaught

This is the second in a series of four articles that discuss underground firefighting preparedness. As with the first article in the May-June issue, it is based on interviews with 214 miners conducted at 7 underground mines (?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996].In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. In this article, we will describe miners? preparedness to evacuate a fire and their experience with incipient fires.

Jan 1, 1997

By A. Wahab Khair, W. M. Devilder

"This paper presents an analysis of fragment size distribution and characteristics of fracture surface in coal cutting using a rotary coal cutting simulator. Coal cutting by a drum type continuous miner was simulated in the laboratory. A series of tests along both the face and butt cleat direction of coal under different operating and in-situ conditions were performed. In each experiment the cut surface was photographed microscopically and the coal cuttings were collected and sized. Data were used to show how and to what extent various parameters effect size distribution of the coal cutting and how this correlates with the characteristics of the fracture surface. This study resulted in establishing a number of distinct correlations between the size distribution and fracture surface. These correlations were primarily based on the degree of interaction between adjacent bits and the amount of bit-coal interaction taking place on the cutting path. Some of the major results of this study are as follows:Zones of bit-coal interactions proved vital toward understanding the effect the conical bit has on the fragmentation process. This in turn led to the identification of areas which are responsible for the production of fines and generation of respirable dust.The various parameters employed in the coal cutting experiments which showed a strong effect on the coal fragment size distribution were: bit type, bit spacing, depth of cut, in-situ stresses, and cleat orientation. Bit angle and cutting head velocity exhibited the least effect and no correlation was established.From this study it is obvious that the key to achieving efficient coal fragmentation is to limit the degree of bit-coal interaction that takes place throughout the bit path while causing maximum interaction between adjacent bits. Accomplishing this not only increases the percentage of large fragments produced but limits the amount of secondary crushing that takes place in the bit path thus resulting in decreasing fines and consequently, the amount of respirable dust generated.Over 2,000 continuous mining machines (introduced in the 1950's) equipped with conical bits or point attach bits account for well over half of the United States' production from underground coal mines. Today, competition in the coal industry has increased, due mainly to coal market conditions and legal restrictions, thus placing an emphasis upon increasing production, efficiency and health/safety of the workers. Mine operators are always interested in finding the most efficient performance of continuous mining machinery to produce the largest amount of size of coal at the lowest cost. An increase of fine material sent to the cleaning plant can seriously overload the plant to the extent that plant efficiencies deteriorate significantly (1). Also, the difficulty and expense of cleaning very small particles often cannot be done economically and thus, thousands of tons of coal are sent to the refuse pile because of costly or ineffective cleaning facilities. It has been said, ""the efficient extraction of coal or rock implies breakage into a size range that contains a minimum quantity of very small sizes"" (2). All known fragmentation theories concur that more fragmentation requires more energy (3). So, the importance of reducing fines is already evident from an outlook upon efficiency.Now, let's consider another view point., duet generation."

Jun 1, 1988