Search Documents

By Morton Corn

The U. S. Federal Coal Mine Health and Safety Act of 1969 placed limits on the permissible concentration of airborne respirable coal mine dust. Evidence exists which suggests that the effects on health of respirable coal mine dust may depend on both host factors and dust properties other than concentration. Dust particle size, shape, density, specific surface area and chemical composition are among the dust parameters of interest in an epidemiological investigation of coal workers' pneumoconiosis and coal miner exposure to mine dust. The purpose of this investigation was to develop and demonstrate the feasibility of techniques to determine selected properties of respirable coal mine dust. An approved underground horizontal elutriator which samples air at 36 cfm was designed, fabricated and utilized in this study to collect respirable coal mine dust in three mines representing the Pittsburgh, Lower Freeport and Lower Kittanning coal seams. Analytical procedures for measurement of respirable dust sample particle size, density, random projected area, total surface area and chemical composition are presented. Results of analyses of three samples collected in each mine are presented. Up to five full work shifts of sampling were required to accumulate approximately five grams of respirable coal mine dust in each sample. Statistical tests were applied to determine the significance of differences between properties of dust samples collected in the same mine and between arithmetic mean values of dust properties representing three samples collected in each mine. A comparison was also made between

Jan 1, 1972

By Kenneth P. V. Lei

The Bureau of Mines investigated a silver-catalyzed oxidative procedure for leaching an arsenical copper sulfide concentrate containing 10 pct As and 32 pct Cu_ Currently, there are no environmentally safe means to treat arsenical copper concentrates in the United States. Leaching was conducted in a 2-L autoclave reactor. The effects of catalyst concentration, O2 pressure, temperature, and H2S04, Cu, As, and Fe concentrations in the leaching solution on extractions of metals from the concentrate were determined. The best leaching conditions for extracting 95 pet eu and As and less than 21 pct Fe were 260 g/L concentrate, 0.007 mol/L (1.0 g/L) AgCI, 3.0 mol/L (294 gIL) H2S04, 1000 C, 60 psig 02, and 6 h. Copper as CuS04-5H20 was recovered by crystallization from the pregnant solution. Arsenic, as AS203, was recovered from the copper mother liquor by solvent extraction, with tributyl phosphate, S02 reduction of As5+ to As3+ in the strip solution, and crystallization of the As3+. The silver catalyst was recovered by contacting the leached residue with a brine solution. A conceptual scheme is proposed for treating arsenical copper sulfide concentrates.

Jan 1, 1987

By Wallace W. Roepke

The Bureau of Mines studied the cutting characteristics of point-attack bits to reduce airborne respirable dust and energy during cutting. Linear cutting of two coal types using four bit types at three depths of cut with three space-depth ratios was performed with a modified horizontal milling machine using an optical particle-size monitor for respirable dust sampling. The cutting action of one bit on a rotary hardhead mining machine was mathematically analyzed and compared with the results of the linear cutting test. Airborne respirable dust per unit mass cut (specific dust) was found to be a monotonically increasing function of specific energy. Specific dust and energy decrease with increasing depth of cut. The amount of nonairborne respirable dust was 100 to 1,000 times greater than the airborne dust. The plumb-bob bit produced the most airborne respirable dust and the highest specific energy of the four bits tested. Rotary cutting was a greater dust producer and energy consumer than linear cutting because of the constantly changing depth of cut, space-depth ratio, and attack angle of the bit relative to the horizontal bedding planes. A new cutting technique is proposed to minimize the existing problems of the rotary cutting machines by providing greater production, reduced dust, and minimized methane ignition potential at the face.

Jan 1, 1976

By Danton L. Paulson

Elevated temperature electrical resistivity measurements were made by the Bureau of Mines on arc-melted, spin-cast, and hot-pressed columbium carbide¬carbon (CbC-C) and zirconium carbide-carbon (ZrC-C) materials up to 2,000° C. The CbC-C materials displayed electrical resistivity values ranging from 35.20 microhm cm at 23° C for hot-pressed material containing 12 wt pct carbon to 242.64 microhm cm at 1,622° C for arc-cast material containing 17.0 wt pct carbon. Electrical resistivity values ranged from 29 microhm cm at 20° C for arc-cast ZrC-C containing 16 wt pct carbon to 279 microhm cm at 1,951° C for hot-pressed ZrC-C containing 21 wt pct carbon. Data from a previous report were included to establish comparison between the electrical resistivities of the CbC-C, ZrC-C, and HfC-C systems.

Jan 1, 1969

By Robert S. Sanford

Intensive investigations of domestic manganese deposits were conducted by the Bureau of Mines and the Geological Survey during the earlier part of the war minerals investigations when there was doubt that the quantity of manganese needed to produce the greatly increased tonnage of steel demanded for war supplies could' to obtained from its customary sources. Domestic deposits of ores that contain sufficient manganese for direct production of ferromanganese essential in steel Manufacture are generally small, and the bulk of the supply is imported. One of the few large deposits of low-grade manganese ore known in the United States is in the Artillery Peale district in southern Mohave County, Ariz. Manganiforous sediments underlie a very large area. Several large groups of claims, covering the most of the manganese-bearing ground, wore assembled in 1929 and 1930. The greater part of this area was leased by the M. A. Hanna Co. in 1937. Investigations by engineers and geologists for this company revealed that the average content of manganese is very low; but that the Maggio Canyon area, about 180 acres, contains higher-grade material. The company put down 28 vertical diamond-drill holds to explore this ground, under the direction of B. N. Wobbor, geologist.

Jan 1, 1948

By W. M. Traver

During World War II, the Bureau of Mines investigated a large number of ore deposits in the United States and Alaska in a search for domestic sources of strategic minerals. Deposits chosen for exploration included those expected to contain metals of importance in the successful prosecution of the war. This report describes exploration of a district of known antimony occurrence on Coyote or Antimony Creek near Antimony, Garfield County, Utah. A preliminary report by Paul T. Allsman, Chief of the Bureau's Salt Lake City branch made in August 1941, recommended further investigation, and proposed methods for performing the work. The project, begun in November 1941 and completed in January 1942, included trenching and sampling in four of the most promising parts of the area The Federal Geological Survey cooperated in the work by detailed mapping and assisted in the interpretation of geologic data.

Jan 1, 1949

By Young W. A.

The Eagle Silver mine is in the Rush Valley mining district, Tooele County, Utah, and is now operated by the Hampton Mining Co. The property, originally referred to as the Argent, is reported to have been one of the first discoveries in the district. The early operators mined ore to a depth of 850 feet, at which point the property was abandoned because of excessive water. During 1905 the Honerine tunnel was driven into the area approximately 1,800 feet below the collar of the Argent shaft. This tunnel served to drain the levels above and operations were resumed. Ore deposits in the Eagle Silver mine occur in the Galena King lime-stone, a 20-to 60-foot member of interbedded quartzite and limestone in the Oquirrh formation of Pennsylvanian age. This member has been faulted along the bedding, forming the Galena King gouge. Mineralization commonly occurs in or near this gouge area in a brecciated, highly altered, pipelike zone. The known ore shoots occur in association with the breccia pipe, commonly adjacent to cross faulting and porphyry intrusions. In general, two ore shoots have been mined on the upper levels of the mine, one lying to the east and the other to the west of the breccia zone. The Bureau of Mines diamond-drilling program was begun during the latter part of 1948 and completed early in 1949. Nine holes were drilled, aggregating 852.8 feet. Sludge and core samples from mineralized sections were analyzed in the Salt Lake City laboratories. A total of 87 sludge, 71 core, and 11 chip samples was submitted for analysis.

Jan 1, 1950

By A. W. Deurbrouck

Five preparation plants employing concentrating tables for washing 3/8- inch to 0 raw coal were tested. Two of the plants were washing Pittsburgh-bed coal, two were washing Pocahontas-bed coal, and one was washing Elkhorn-bed coal. Samples of the feed to and products from the tables were collected over the normal operating shift. These samples were analyzed, and complete performance criteria were determined. The results of this study show that the concentrating table is an effective fine-coal cleaner even when operating at 40 percent over the recommended 10 tons per hour feed rate. Recovery efficiencies for the 3/8-inch to 200- mesh size fraction ranged from 97.3 to 99.3 percent; maximum yield errors and ash errors were 2.4 and 1.0 percent, respectively; probable errors ranged from 0.074 to 0.115 specific gravity units and error areas from 52 to 73 square centimeters. The amount of minus 200-mesh material in the water used for feed water and dressing water to the table had no significant effect on the sharpness of the separation achieved but did have an effect on the ash content of the clean- coal product. In the one plant studied, the substitution of fresh water for plant circulating water reduced the ash content of the clean coal by about 6 percentage points.

Jan 1, 1963

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By James Westfield

Uranium activity has introduced a comparatively new hazard to United States mining. In addition to the hazards common to all mines, uranium mines have a complex health problem of radiation damage. Like many new processes, radiation and nuclear energy can be made to serve man in many useful ways when properly understood and handled; but, like fire, gases, and electricity, their potential dangers must be known and respected, and appropriate precautions must be taken or death may result. Since 1950 the Public Health Service has been conducting basic investigations on exposure to radon and its daughter products and the effect of exposure upon the health of miners in uranium mines of the Western States. The Bureau of Mines assisted in several of these investigations, especially in mines on Indian lands. The studies have shown that a serious health hazard exists from radioactive exposure that might cause lung cancer if continued over a number of years. The Public Health Service report, Control of Radon and Daughters in Uranium Mines and Calculations on Biologic Effects,6/ shows that 55 percent of the uranium mines employing 64 percent of the miners had atmospheric concentrations more than five times the working level now accepted as reasonably safe for industrial exposures. Extensive control measures are necessary to reduce these concentrations to the suggested working level of less than 300 micromicrocuries of total radon daughter products per liter of air.

Jan 1, 1958

By Oliver Bowles

The use of fire as a source of heat was the first step from primitive existence toward modern civilization, and heat has performed functions of inestimable importance throughout the ensuing ages. The first commercial steam engine invented in 1698 demonstrated that heat was an important source of power, and heat has since become the motivating force for railroad trains and steamboats as well as for machines in multitudes of factories. Aside from its function of supplying power, heat is an agent of vast importance in chemical reactions and engineering processes. Because of the high temperature of steam under pressure, losses by radiation from boilers and pipes become excessive unless the radiating surfaces are covered with insulating materials. Insulation is important also for hot-water pipes and many other types of equipment from which heat may radiate. Radiation losses from heated surfaces increase rapidly

Jan 1, 1943

By M. L. Glenn

The Bureau of Mines is conducting research on Fe-based alloys using Si and Al additions to reduce the Cr required for heat-resisting appli-cations. Part of this research is being done to evaluate alloys containing (8-10)Cr-(10-14)Ni-(0-8.5)Si-(0-4) Al to determine which of these alloys have austenitic structures, as well as fabrication properties and oxidation resistance sufficient to substitute for type 304 stainless steel. Based on initial results, an Fe-lOCr-11Ni-5Si alloy and an Fe-8Cr-13Ni-5Si alloy were selected for evaluation of oxidati.on, stress rupture, and tensile properties. Both alloys have oxidation resistance at 7000 and 8000 C that is better than that of type 304 stainless steel. The stress rupture strengths are less than that of type 304 stainless steel but significantly better than that of commercial heat-resisting steels with similar Cr contents. Yield strengths of the alloys were equivalent to that of type 304. Both alloys had high tensile strengths comparable to those of stainless steels that transform to martensite during straining (e.g., type 301). These alloys have weld-hot-cracking resistance comparable to that of type 304 stainless steel. This initial study shows that Si has potential as a substitute for Cr in stainless steels for heat-resisting applications.

Jan 1, 1984

By H. R. Shell

Of three known compounds in the ternary system K20 - PbO - SiO2, one having the composition K2Pb4Si8021 crystallizes into a structure with asbestiform properties. This compound, whose silicon-oxygen ratio is between that of the layer silicates (for example, mica) and the double-chain amphiboles, crystallizes in the tetragonal system. It malts, apparently congruently, at 779° C. The fiberized product prepared from crystals is fluffy and closely resembles natural asbestos in appearance, but is more brittle and has less strength. However, potassium-lead silicate may be separated into fibers with a uniform diameter of 200-300 A.U., and the fibers show with the electron microscope the s criteria that have been interpreted as indicating a hollow tube structure in chrysotile asbestos. Since very few inorganic crystalline compounds have such a structure, the material has unusual scientific interest. Microcrystalline potassium-lead silicate was rapidly and completely formed when powdered glass of the same composition was heated to 650° - 700° C, but macrocrystals grew only slowly from the viscous massive glass. Maximum growth rate was 0.12mm. per hour at 700° C.

Jan 1, 1957

By R. T. Sorensen

Bench-scale and continuous testing were performed to adapt the anionic process for flotation of calcium activated silica to the fine-grained hematitic-goethitic jaspers from the Marquette range, Michigan. These ores typically contain about 35 percent Fe and require grinding to about 80 to 100 percent minus 400 mesh to insure an adequate liberation of gangue from the iron oxides. A method for removal of troublesome slime fractions without excessive iron loss, by first dispersing the quartz and then selectively flocculating the iron oxides, was evolved in the laboratory and successfully accommodated to pilot plant practice. The efficiency of the flotation process was improved with respect to both reagent usage and concentrate grade and recovery by using the selective flocculation-desliming technique as a pretreatment. The benefits of the combined desliming-flotation procedure were most evident in pilot plant processing. The best tests on two ores yielded recoveries of about 84 percent in concentrates containing 65.1 percent Fe and 4.8 percent SiO2 and 66.2 percent Fe and 3.9 percent SiO2, respectively. These results are in comparison to recoveries about 10 percent lower than the above to concentrates containing 63.9 percent Fe and 6.6 percent SiO2 in the one instance, and 63.6 percent Fe and 7.2 percent SiO2 in the other, obtained by flotation without the prior desliming treatment.

Jan 1, 1967

By D. K. Steele

The domestic primary copper industry generates in excess of 600 million t of mining and mineral-processing waste annually. Most of the waste poses negligible environmental threat, but a small fraction, because of toxic or corrosive characteristics, may be subject to regulation under Subtitle C of the Resource Conservation and Recovery Act (RCRA) or other pertinent regulations. Among the wastes generated by various copper producers are flue dusts, slags, refinery-bleed solutions, and. acid-plant wastes. The U.S. Bureau of Mines (USBM) has researched methods to mitigate the environmental threat posed by copper-processing wastes while recovering valuable metals from these materials. Acid-leach processing of flue dusts has been demonstrated feasible along with sulfide treatment of liquid refinery wastes and acid-plant-bleed and gas-cleaning solutions to precipitate dissolved metals. In, addition, the feasibility of removing copper and molybdenum from slag, as well as stabilization of precipitated sulfide wastes by vitrification, have been investigated.

Jan 1, 2010

By George L. Gates

The Bureau of Mines studied pressure-buildup data from a number of California gas wells to determine if the reservoir properties calculated from these data correlated with field-observed reservoir properties. Pressure-buildup curves from 24 wells showed distinct changes in slope, indicating changes in permeability of the reservoir rock. Calculated distances from the wells to indicated permeability changes were in fair agreement with distances deter-mined in the field. Pressure-buildup curves from three wells had more than one distinct change in slope, indicating multiple permeability changes. Thus field data supported the theoretical relations used to calculate reservoir properties from pressure-time relations measured in gas wells.

Jan 1, 1967

By F. F. Aplan

Separation of the slightly soluble minerals (Ksp? 10-10), one from the other is one of the more difficult tasks confronting flotation engineers. This study has focused on means of separating such prominent members of this class as scheelite, fluorite and calcite from one another. Some experimental work has also been done on the minerals magnesite, dolomite and apatite. Carboxylic acid-type collectors are commonly used industrially to float all of these minerals. Thus, the problem at hand is to ascertain means of achieving selectivity between minerals known to respond rather similarly in flotation. Four techniques have been proposed for the separation of minerals of this class from each other: 1. Control of potential determining ions 2. Use of stereo-specific collectors 3. Use of flotation rate differences 4. Use of selective activating and depressing compounds. This study was directed toward a cursory evaluation of each of these techniques, and each was found to be a possible method of achieving selectivity. Stereo-specific collectors -- those whose parking area may closely match the available adsorption site on one mineral but not on another -- are a possible means of achieving selectivity between scheelite, fluorite and calcite. Stereo-hindered carboxylic acid salts and sulfonates all show selectivity between the three minerals tested. Separations also appear to be possible by the controlled use of the lattice ions (e.g., Ca and [W0=4] for scheelite, CaW04), H+, [OH-, C0-3 and HCO=3]; all of them ostensibly potential determining in the systems studied. Flotation rate differences of the minerals as a function of pH under conditions of starvation collector usage also showed promise. Scheelite and fluorite float most rapidly with sodium oleate in slightly acidic (pH 4-7) solutions whereas calcite floats most rapidly near pH 10. Use of Mn++, Pb++, or other heavy metal hydroxy complexes as activators was seen to effect each of the slightly soluble minerals differently. This is in sharp contrast to the oxygen containing, relatively insoluble minerals, where all minerals respond in a similar manner to such activation procedures. Results indicate that all four methods outlined above may potentially be used to achieve flotation separation of the slightly soluble minerals. More extensive research should be undertaken to detail the spcific applicability of each of the procedures and to make a more complete evaluation of the effect of collector type and concentration, mineral type, pH and size effects.

Jan 1, 1983

By R. H. Grau, A. Sainato, S. J. Schatzel, T. M. Kohler, A. T. Iannacchione

This Bureau of Mines research study found gas emission rates from an advancing face, and flows and pressure of gas from an exploration drill hole were dependent upon the geology of salt encountered in a domal salt mine. Normal production-grade "pure" salt adjacent to an anomalous' zone was found to have a methane emission rate of less than 5 ft3/ ton (0.1 m3/t) of mined salt from a room advanced by a continuous miner. Extremely low gas flows [less the 4 ft3/h (0.1 m3/h)] and lack of pressure buildup were also observed from this normal salt in a 154-ft (47-m) exploration drill hole. These data indicate that methane emissions should not be a problem when mining in this type of salt. In the adjacent anomalous zone, methane emission rates ranged from 15 to 70 ft3/ton (0.4 to 1.8 m3/t) of mined salt from an advancing face. Gas flows of approximately 42 ft3/h (1.2 m3/h), and pressures in excess of 900 psig (6,200 kPa) were observed in an exploration drill hole when the anomalous zone was encountered. This information suggests a greater methane emission hazard from the anomalous zone than from the associated normal salt. If this trend of increasing emissions problems associated with anomalous zones of salt is common with similar anomalous zones encountered or observed in other domal salt mines, then special control strategies should be employed to minimize this potential mining hazard.

Jan 1, 1984

By A. Sainato, S. J. Schatzel, D. M. Hyman, J. C. LaScola

The Bureau of Mines determined the gas contents of 135 oil shale samples obtained from approximately 630 ft of core drilling. Drilling was done within a projected mining zone of the Cathedral Sluffs Mine, located in the Piceance Basin of western Colorado. Methane contents were determined by the modified direct method, which can measure the volumes of several gases released from or reacted with mine rock without destructive sample treatment. Over the duration of the test, nitrogen was largely unreactive, CO2 increased slightly, oxygen decreased markedly, and methane increased more than the total increase of all contained gases. The gas volumes were normalized per unit sample mass and are given in cubic centimeters per gram. Common time irzdices for test duration of 3, 40, and 125 days were used to compare methane desorption among samples. The means of the sample populations for these indices were 0.0316, 0.114, and 0.195 cm3/g, respectively. These quantities are lower than those reported in a Bureau emissions study at the Horse Draw Mine in the Piceance Basin. Oil shale samples that were gas enriched beyond the mean methane contents frequently contained bitumens and pyrite.

Jan 1, 1987

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past-several years the flow of natural bas through high--pressure pipe lines.4 This report deals with that part of the study involving the design of pipe-line, systems consisting of lines laid parallel to each other. The lines are deferred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is, connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934