Search Documents

By Forest J. Sur

"INTRODUCTION This report describes an exploratory project conducted by the Bureaus of Mines on a fluorite deposit, near Glenwood, N. Mex. Results of wagon drilling, crosscutting, and test pitting are given, together with results of metallurgical tests made upon samples of the ore. Mining and treatment methods are suggested.C. H. Johnson, Bureau of Mines engineer, examined the deposit in August 1942. H. E. Rothrock, of the Federal Geological Survey, completed a preliminary geologic study and mapped the deposit during the fall of 1942. As a result of these brief investigations, it was concluded that the deposit contained substantial inferred ore reserves, and exploratory work was recommended. G. A. ApelI, also of the Bureau of Mines, made a topographic and underground survey and report on the mine in March and April 1944. A wagon drill, air compressor, and other equipment and supplies were delivered to the property on May 19 to 23, 1944. Drilling began under the direction of the author on May 25, 1944, and was completed in October 1944. The results of drilling and. sampling form the basis of this report."

Apr 1, 1947

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984

Reduce well construction and operation costs associated with in situ leach mining while increasing mineral recovery. Approach To accommodate the size of centrifugal pumps presently in use, in situ leaching production wells are typically drilled to 6 inches in diameter, while monitor wells are drilled to measure 4 inches in diameter. However, in order to reduce the cost of drilling these larger diameter wells and to increase recovery, the Bureau has developed jet pumps which have smaller diameters than centrifugal pumps of the same capacity. This allows both production and monitor wells to be drilled smaller. Bureau estimates indicate that the cost of drilling a 3-inch-diameter production well at in situ leaching operations would be about 35 percent less than the cost of a 6-inch well. Similarly, the cost of drilling a 2-inch-diameter monitor well would be about 26 percent less than the cost of a 4-inch well. Such significant savings in the cost of drilling these wells would effect a substantial reduction in total capital cost. Use of the new jet pumps can also increase the percentage of recovery because less costly wells allow closer well spacings, improving the distribution of the leach solution. How the System Works After the borehole is cased, the new small-diameter jet pump, along with piping and accessories, is installed and connected to a centrifugal pumping unit on the surface. High-pressure water from the surface pump is forced through a nozzle into the venturi of the jet type pump injector. This jet action lifts the leach and mineral-bearing solution to the surface.

Jan 1, 1984

By Daniel G. Di Canio

A computer based accident cost indicator model (ACIM) for estimating tangible costs of occupational injuries, illnesses, and fatalities in the U.S. mining industry is described. Studies performed to expand the scope of the ACIM to all mining sectors are presented. Validation of ACIM cost element estimation algorithms with actual costs of mining-related injuries and illnesses are presented. A study of the effect of a fatal accident on production in surface coal and metal/nonmetal mines is presented. The study is based on a sample of 15 fatalities in underground and surface mines. Evidence of significant long- term decline in postfatality production at 6 of 8 underground samples is presented. The average loss is shown to be 1.8% of annual mine production. A study of accident costs in U.S. mining from 1975 through 1981 using the ACIM is presented. The study shows that total annual costs increased from $180,000,000 in 1975 to $379,000,000 in 1981, a 15% annual increase after adjusting for inflation, with mining companies bearing 45% of the total and expected wage losses to mining families accounting for 42%. The study shows total costs of $12,400 per accident and $674,000 per fatal accident for 1981.

Jan 1, 1983

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1978 and 1979 was 8831.8 million and $336.4 million, respectively. In 1978, nearly all commodities registered an increase in production and value; unit value increased for all commodities, with the exception of native asphalt and sand and gravel. Alabama led the Nation in the production of crushed marble and was second in bauxite, third in masonry cement, kaolin, native asphalt, and oyster shell, and fourth in bentonite, dimension marble, fire clay, and scrap mica. Trend; and Developments.-The Alabama State Docks at the Port of Mobile handled more than 10 million tons of bulk material in fiscal year 1978; volume dropped slightly to 9.8 million tons in fiscal 1979. Bulk materials comprise the major activity at the facility, with iron ore and bauxite being two of the major materials handled. The movement of these ores is vital to the operation of many heavy industries in the State.

Jan 1, 1981

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 271 natural gas samples from 22 States collected during calendar year 1982. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of the investigation of the occurrences of helium are published annually to make the information available to the petroleum industry and the general public. Twenty-six publications have presented the results of 13,051 gas analyses vide prior to 1982. The first 3 bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26) containing 7,833 analyses of samples collected since 1960.

Jan 1, 1983

By N. E. Hanna

To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain safety tests prescribed by the Federal Bureau of Mines. These tests are described in Schedule 1-G4/ (explosives) and Schedule 26A5/ (blasting devices). An explosive or blasting device that passes the appropriate tests is placed on the active permissible list. As this list is subject to continuous revision, it has been the practice of the Bureau of Mines to publish periodically the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. The present circular gives all explosives and blasting devices on the active permissible list as of December 31, 1957, and shows all changes, additions, and transfers in that list between December 31, 1951,6/ and December 31, 1957.

Jan 1, 1958

By D. J. Parker

The oft-repeated expression that the taproot of safety lies in the attitude of the management toward accident-prevention work is indisputable and has become almost an axiom. Trite and somewhat timeworn though the statement may be, it is nevertheless true that the supervisory force must earnestly support a policy of safety and maintain at all times a con¬ siderate regard for the welfare of the employee if that high degree of cooperation of the employee, so vital to the successful prosecution of any safety program, is to be expected. The responsibility for preventing accidents rests upon the management, and in the case of the Spring Canyon Coal Co. such responsibility is recognized and accepted with little or no reservation. This company, aside from the humanitarian aspects involved, believes that safety is good business and not a matter to be treated passively or in a perfunctory manner. The problems with respect to safety that have been met and wholly or partly solved can best be appreciated when some of the natural conditions, adverse and otherwise, existing at this operation are taken into consideration. Mine 1 is about 1 mile north of the town of Spring Canyon, Carbon County, Utah, and is served by both the Denver & Rio Grande Western and Utah Coal Route railways. During the year 1931 the mine produced 312,397 tons, approximately 10 per cent being derived from pillar workings. The normal daily output during the summer months is about 2,000 tons, and during the peak of production in the winter season the daily production varies from 2,500 to 3,000 tons. The number of miners varies from 87 in summer to 220 in winter, and the day men vary in number from 66 in the winter to 45 in the summer; 12 company men are employed the year around. The officers of the company are J. B. Smith, president, San Francisco, California; T. R. Stockett, general manager, Salt Lake City; and G. A. Murphy, superintendent, David Brown, assistant superintendent, and John Sullivan, mine foreman, all of Spring Canyon, Utah.

Dec 1, 1932

By Seth C. Schaefer

[As part of the Bureau of Mines effort to provide thermodynamic data for advancement of mineral resources technology, the standard Gibbs energies of formation (?G°f) of MnS (manganese sulfide) and Fe0.9 S (pyrrhotite) were investigated with a high-temperature galvanic cell employing stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnS, MnO, S02 (g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt with the overall cell reaction MnS (s) + 1.5 02 (g, 0.0114 atm) = MnO (s) + S02 (g) . (1) These results give the standard Gibbs energy of formation of MnS for the reaction Mn (s) + 0.552 (g) = MnS (s) (2) ?G°f = -66.487 + 15.19 x 10-3T±0.207 kcal/mole (896.4 - 1,208.1 K) (3) where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, FeO .9S, Fe304 , S02 (g, 1 atm) //Zr02//02 (g, 0.0114 atm) , Pt with the overall cell reaction 10/3 FeO .9 S (s) + 16/3 02 (g, 0.0114 atm) = Fe.,04 (s) +10/3 S02 (g). (4) These results yield the standard Gibbs energy of formation for the reaction 0.9 Fe (s) + 0.5 S2 (g) = Fe0.9 S (s) (5) ?G°f = -35.229 + 12.67 x 1073T+-0.104 kcal/mole (839.5 - 1,086.6 K). (6) A third-law analysis of MnS data yields a standard enthalpy of formation (AH°f) for the reaction Mn (s) + S (rh) = MnS (s) (7) ?H°f298 = -51.16±0.21 kcal/mole (8) A similar third-law analysis for Fe0.9S data yields a ?29°f298 for the reaction 0.9 Fe(s) + S(rh) = FeO .9S(s) (9) ?HO\°f298 = -24.01±_0.15 kcal/mole. (10) ]

Jan 1, 1980

By Jay F. Colinet

Respirable dust exposure has long been known to be a serious health threat to workers in many industries. In coal mining, overexposure to respirable coal mine dust can lead to coal workers? pneumoconiosis (CWP). CWP is a lung disease that can be disabling and fatal in its most severe form. In addition, miners can be exposed to high levels of respirable silica dust, which can cause silicosis, another disabling and/or fatal lung disease. Once contracted, there is no cure for CWP or silicosis. The goal, therefore, is to limit worker exposure to respirable dust to prevent development of these diseases. The passage of the Federal Coal Mine Health and Safety Act of 1969 established respirable dust exposure limits, dust sampling requirements for inspectors and mine operators, a voluntary x-ray surveillance program to identify CWP in underground coal miners, and a benefits program to provide compensation to affected workers and their families. The tremen­dous human and financial costs resulting from CWP and silicosis in the U.S. underground coal mine workforce are shown by the following statistics: ? During 1970?2004, CWP was a direct or contributing cause of 69,377 deaths of U.S. underground coal mine workers. ? During 1980?2005, over $39 billion in CWP benefits were paid to underground coal miners and their families. ? Recent x-ray surveillance data for 2000?2006 show an increase in CWP cases. Nearly 8% of examined underground coal miners with 25 or more years of experience were diagnosed with CWP. ? ?Continuous miner operator? is the most frequently listed occupation on death certificates that record silicosis as the cause of death.

Jan 1, 2010

By John D. Foulkes, David A. Curtis, Robert L. Lagace, John L. Rothery

An investigation is made of the feasibility of developing compact transmit antennas and/or other means to efficiently couple VLF to MF band radio energy between portable wireless communication units in coal mines. The completely wireless communication ranges between two portable radios equipped with practically-sized reference loop antennas in representative coal mine environments are estimated. Antenna technology is assessed with respect to transmit moment, range, intrinsic safety, battery and wearability requirements to deter- mine the most suitable antenna types for use by miners. It is concluded that air-core bandolier loop antennas, and perhaps ferrite-loaded loop antennas, having peak transmit moments of about 2.5 ampere-m5 will be the most effective antenna choices for portable units. This choice, however, will not allow the range goal of 1350 feet to be attained in mines having unfavorable signal attenuation and noise environments. Rectangular air-core loops are compared with grounded horizontal-wire and vertical-wire mode exciters for fixed station applications. The potential for significantly increasing the wireless communication range by inductively coupling to communications and power lines in a mine is evaluated and found to be considerable based on theoretical coupling equations. Lastly, the theoretical performance of a hybrid noise cancelling diversity receiving technique that utilizes both the electric and magnetic field components of the ambient noise to improve the receiver output signal-to-noise ratio under certain adverse conditions is estimated and shown to be favorable when the magnetic and electric field noise components are highly correlated.

Jan 1, 1977

By John A. Burgess

The Carson Hill mine of the Carson Hill Gold Mining Corporation is at Melones, Calaveras County, Calif. It is one of the numerous mines on the Mother Lode of California. The property extends for 8,400 feet along the outcrop of that important vein system. The elevation at the haulage level is about 1,000 feet above sea level. ACKNOWLEDGMENTS Acknowledgment of assistance in the preparation of this paper is made to Frank Wagner, underground superintendent; Max Petersen, engineer; and Homer Mann, assistant engineer. The geology of the Mother Lode has been described by Adolph Knopf in Professional Paper 157 of the United States Geological Survey; references to general geology have been abstracted largely from Knopf.

Jan 1, 1937

By Frank L. Hess

In 1876 cassiterite was identified in the placer gold from the northern Black Hills, and such a mixture could have come only from Nigger Hill or one of the streams draining the hill, because in no other part of the northern hills have cassiterite and gold been found together. Nigger Hill is in western Lawrence County, South Dakota, and on it is the little camp of Tinton. The Wyoming line runs along the west side of the hill and crosses the ridge which is the hill's continuation about miles north-northwest of Tinton.

Jan 1, 1938

By A. D. Mah

To assist Bureau of Mines research in extractive metallurgy and to add to the thermodynamic data base useful to others, energy calculations were made for 63 reactions relating to investigations on the production of anhydrous aluminum chloride from chlorination of clay.

Jan 1, 1982

By d&apos, Kathleen J. Amico

THIS SUAMMARY is shown in Minerals Yearbook volumes I and III of this series on mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, and on the principal minerals imported into and ex- ported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1962

By Henry E. Perlee

In a Bureau of Mines study two-dimensional mathematical equations were solved that describe the transient thermal response of a rock dust particle in a cloud of similar particles in a gas flame's preheat zone subject to a radiant field from the approaching flame. The description includes both radiant energy absorbed and emitted by the particle and thermal conduction inside the particle and into the surrounding gas environment moving relative to the particle. Two situations were studied; in one the radiant energy incident on the particle is converted to thermal energy at the particle surface, and in the other the radiant energy is converted to thermal energy uniformly over the volume of the particle. The result of the study showed that for a 10-µm-radius particle, a 200-mg 1-1 loading density, and a flame approach velocity of 30 m sec-1, the particle temperature rise was twice that previously calculated by Singer and Cook based on the model of Essenhigh and Csaba. It was further established that under the conditions examined a rock dust particle temperature never increases more than about 200 K before crossing the flame front.

Jan 1, 1976

The Technology Transfer Seminar on Mine Communications held on March 21-22, 1973, at the Pittsburgh Mining and Safety Research Center, Bruceton, Pa., presented information about recently developed equipment, instruments, and techniques for use in mine communications systems. All of the basic ideas presented in the fine seminar are operational in the Bureau of Mines Safety Research Mine in Bruceton.

Jan 1, 1974

By John C. Machisak

Statistical data on injuries in the metal and nonmetal industry of the United States first became available to the Bureau of Mines by collecting reports from the operators for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1954, is the 31st publication (1933-34 was published as Bulletin 398) containing statistical data on injuries at metal and nonmetal mines and related plants, and it 1s the first such bulletin to be published since 1942. The last publication was Bulletin 461, Metal and Nonmetal-Mine Accidents in the United States, 1942. The unpublished statistics for 1943-53 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries and related employment at metal and nonmetal mines, but there is no Federal law that compels operators to submit such information. Therefore, all materials submitted are voluntary responses to the Bureau's requests for information. The figures presented herein may not be complete for the entire industry, nevertheless, every effort has been made to make them so, and the data given are believed to be representative of the hazards to which metal and nonmetal workers are exposed. Moreover, the figures are comparable as between States-which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1957

By John C. Machisak

THIS INFORMATION CIRCULAR contains 1956 and 1957 injury experience and employment data for metal mines in the United States and Alaska. Unlike previous publications, this report covers only metal mining and contains statistical data on injuries and employment pertinent to metal mines and mills reporting voluntarily to the Bureau of Mines on an annual basis. Injury and employment data for the nonmetal industries, which from 1911 through 1955 were published in the same series as the metal industries, for the first time will be published separately as an information circular entitled "Injury Experience in the Nonmetal Industries, 1956 and 1957." The Bureau of Mines is authorized to make requests for injury and employment data, and the information submitted by operators of metal mines and mills is a step forward in promoting safety in the metal-mining industry. Every effort has been made to make this coverage as complete as possible.

Jan 1, 1960

By R. H. Lien

The Bureau of Mines developed a flue gas desulfurization process as part of its goal of minimizing the undesirable environmental impacts associated with energy and mineral-processing plants. The modified citrate process involves absorption of sulfur dioxide (S02) in a buffered citric acid solution. The S02-loaded solution is regenerated by countercurrent contact with steam in a packed tower. The wet S02 product is then dried and can be liquefied or further processed to make sulfuric acid. Test data from process investigation unit studies are presented. Material balances, flowsheets, and cost estimates are given for recovering S02 from copper smelter reverberatory gas, lead smelter sintering machine tail gas, and power-plant stack gas. Operating cost estimates show the process will add $0.04 per pound of copper, $0.01 per pound of lead, and $0.015 per kwhr to the cost of the respective operations. These costs could be substantially reduced if a source of waste heat was avail-able to provide the process steam requirements.

Jan 1, 1982