Search Documents

By J. W. Adams

This report surveys the efforts of six contractors to the U.S. Bureau of Mines with regard to their electromagnetic noise measurement programs. What has been done, what is planned, and evaluations and recommendations are given for each contractor. The main observation is that to date there is not sufficient knowledge of electromagnetic interference in mine environments to design a reliable communication system. This knowledge should be available by the end of June 1972 if certain planned programs are completed successfully. A major effort of this report is to establish parameters to be measured, units to be used, and workable formats for data presentation. This is given in Appendix A. Some details concerning equipment, procedures, locations, and sample data are included in Appendix B.

Jan 1, 1971

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future. To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 829), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1984

All of the coal resource in North Dakota is lignite. The lignite fields of North Dakota cover approximately 40 percent of the total area of the state, with reserves estimated to be 9.8 billion tons, two percent of the U.S. base. The first commercial coal mine in North Dakota opened in Morton County in 1873. As the railroads crossed the plains, the demand for coal increased. Coal for fuel was supplied by the state's underground mines. By 1884, North Dakota's lignite production had reached 35,000 tons. North Dakota was among the fist states to shift from underground to large-scale commercial surface coal mining. By 1927,40 percent of the total production was by surface mining, compared to 2 percent for the nation as a whole. By 1959,86 percent of the total production was by surface mining, while the national average was 22 percent. Since 1966, surface mining has been the exclusive coal production method in North Dakota. North Dakota's regulatory program received conditional approval December 15, 1980. Following approval of amendments to the program, it received full approval February 18, 1986. The Abandoned Mine Lands Program was approved December 23,1981.

Jan 1, 1992

By F. K. McIntosh, L. A. Dahmers

"INTRODUCTION North Carolina has been the leading producer of mica in the United States, accounting for roughly 50 percent of the Nation's output. The producing area is a belt some 100 miles in width lying in the Mountain and Piedmont sections in the western part of the State. Ashe, Watauga, Avery, Mitchell, Yancey, Buncombe, Haywood, Jackson, Macon, Transylvania, Rutherford, Cleveland, and Lincoln Counties supply the bulk of production, while small amounts have been produced in Gaston, Catawba, Burke, Wilkes, Yadkin, Stokes, and Person Counties.To assist the operators and expedite the production of mica during the recent emergency, the Bureau of Mines drilled four of the more promising mica properties in this State. The results of this exploratory program are recorded in this report.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, L. B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and makes beneficiation tests."

Apr 1, 1948

By Michael K. Phang

The use of explosives to fragment rock generates ground vibrations which may have a detrimental effect on contiguous underground coal mine openings. Increased surface blasting by a burgeoning number of surface coal mines and quarries has caused considerable concern among underground mine operators. Ground vibration effects generated from surface mine blasting are also causing public concern. In response to this concern, the U.S. Bureau of Mines (Stagg and Engler, 1980) has measured and analyzed ground vibrations and their effects on underground and surface structures. Some of the complaints registered against the mining industry are claims of substantial material damage from vibrations generated by the blasting; others are nuisance complaints of minor damage or annoyance. In general, allegations of damage from surface blasting have been sufficiently numerous to constitute a major problem for mine operators engaged in blasting operations. They have recognized the need for more technological data to evaluate the vibration problems associated with blasting. Both the operators and the general public need adequate safeguards based upon factual data to protect their specific interests. The coal mine industry needs reliable information from which to change blasting operations to reduce the number and severity of major damage claims and eliminate the growing number of nuisance complaints. The problem is of major concern not only to coal mine operators and nearby property owners, but also to federal, state and local governments. At the same time, environmental control agencies responsible for blasting and explosives use require reasonable and appropriate guidelines to protect the miners' lives.

Jan 1, 1984

By J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly In the form of byproduct salt cake from the acid manufacturers, has been tending to decrease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This dean is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorable situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4 ? 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting, even the dehydrated product to market is the deciding economic factor. Therefore, the recovery oil production of anhydrous sodium sulphate from plant-.waste liquors or from natural brines of suitable composition might be economically feasible. The U.S. Bureau of Mines, at its nonmetallic Minerals Experiment Station, New Brunswick, N. J., has, for a number of rears, been investigating the commercial possibilities of treating the complex saline mineral polyhalite (K2SO4?NgSO4?2CaSO4?2H20) for the recovery of potash and magnesia. Certain proposed processes (1, 2, 3, 4)4/ yield waste liquors that contain the bulk of the magnesium and sulphate originally combined as magnesium sulphate in the polyhalite molecule. Sodium chloride In limited concentrations is also present, as extensive beds of salt occur in strata overlying the polyhalite deposits. A typical waste liquor would contain:

Jan 1, 1936

By CHARLES L. WRIGHT

Coals may be divided into six classes-anthracite, semi anthracite, semibituminous, bituminous, subbituminous, and lignite. The first three cla~ can be distinguished by dHferences of composition, particularly the proportions of fixed carbon and the ratios of the fixed carbon to the volatile matter in the cools. The last three classes can be distinguished by di:fferences in physical character, chiefly in color and in manner of weathering. Lignite is brown, not black, and has generally a woody look, but it weathers in much the same way as subbituminous coals. On exposure to the air lignite slacks or crumbles. The lumps check and fall into small irregular pieces that exhibit a decided tendency to separate into extremely thin plates. Hence lignite deteriorates greatly during storage or long transportation. The most characteristic feature of the composition of lignite is a large percentage of moisture. '!his high moisture content reduces the fuel value of freshly mined lignite, and the partial evaporation of moisture, on expooure, causes th6 fuel to check and fall to pieces. Consequently, attempts to increase the efficiency of lignite as a fuel involve reducing its percentage of moisture and increasing its ability to endure storage and transportation. Both these results are accomplished by briquetting.

Jan 1, 1911

By J. P. Morris

"INTRODUCTION In the investigation being conducted by the Bureau of Mines concerning the production and utilization of sponge iron, it soon became evident that more information was needed regarding methods for determining the degree of reduction attained in the manufacturing process. Sponge irons made by different processes vary in physical characteristics and chemical composition, and a method of analysis that is suitable for one type is not necessarily applicable to all others. For example, the hydrogen-evolution method, which measures the volume of hydrogen evolved upon treating the sample with acid, accurately determines the oxygen content of some types of sponge iron. However, when the sponge iron contains combined carbon, hydrocarbon gases are also-evolved and large errors may result. Probably no single method will give accurate results in all instances, and for this reason it is desirable to have several reliable procedures available and to know the limitations of each.For measuring the degree of reduction, determination of either metallic iron or oxygen should suffice, although for practical application of sponge iron to the production of steel the oxygen content is more significant. After consideration of proposed methods of analysis in regard to their suitability for routine use and the probable influence of other substances, four procedures were chosen for investigation:(1) Mercuric chloride method.(2) Copper sulfate method.(3) Hydrogen-reduction method.(4) Hydrogen-evolution methods."

Sep 1, 1945

By A. W. Fahrenwald

The art of flotation has developed rapidly. Numerous technical staffs and individual investigators have, by their combined efforts, developed practicable methods of concentrating ores which ten or even five years ago were considered complex and impossible of commercial treatment. Also the work of those who have been engaged in pure research on the fundamentals of flotation has helped greatly to expedite the general development of the process. However, in spite of the highly successful practical operation of the flotation process, results are obtained and things happen that we are unable to explain completely, although much is known about the theory of the process. The rapid stride in flotation concentration, it is noteworthy to point out, is due to the freer exchange of facts and data by the staffs of the larger mining companies and the patent controlling corporations, and by investigators in general. Generally speaking, one may visit any mining plant and by presentation of proper credentials, be shown all that is going on or that is being done.

Jan 1, 1925

By L. E. Cardwell

This publication contains routine analyses and related source data for 377 natural gas samples from 19 States and two foreign countries. Of this total, 373 samples were collected during calendar year 1970. The remaining four samples were collected during previous years, but releases granting per-mission to publish the analyses were not received until 1970. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Twelve previous publications have presented the results of 9,050 gas analyses prior to 1970. The first three, Bulletins 486,6 576,8 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1971

By Dennis R. Dolinar

The National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory conducted a full-scale test of a composite polyurethane-aggregate seal in a hydrostatic chamber at the Lake Lynn Experimental Mine. This composite seal consisted of a polyurethane and limestone aggregate core that was formed between two concrete block walls. In the hydro-static chamber test, water is used to pressurize the seal. During the test, the maximum average water pressure the seal was able to withstand was 18.9 psi. Further, the seal began to yield at an average water pressure of only 17 psi. At the time of the test, the minimum seal design requirement was 20 psi under 30 CFR4 75.335 (2005). Therefore, based on this test, the seal did not meet the regulatory minimum design requirement. Uniaxial compressive tests conducted on samples from the polyurethane-aggregate core revealed that both the compressive strength and the elastic modulus of the material were much less than that for polyurethane only with a density of 10.0?12.0 lb/ft3. The significant reduction in the strength and stiffness of the polyurethane-aggregate mixture results from the formation of a soft polyurethane foam around each piece of aggregate. The formation of the soft foam seems to be caused by residual moisture from the aggregate. The moisture also caused the density of the polyurethane in the polyurethane-aggregate mixture to be less than the design requirements. The lower density of the polyurethane in the mixture, along with the formation of zones of pure polyurethane only, resulted in the overall seal density being less than the design requirements. During seal construction, steps were taken to control the moisture, but were not successful. An analysis of the seal failure showed that the calculated shear stresses at failure and the estimated shear strength of the polyurethane-aggregate mixture are fairly close. This suggests that the strength properties of the polyurethane-aggregate mixture along with a weak zone of poorly bonded aggregate controlled the maximum pressure the seal could withstand. At the time of the seal testing, the minimum design requirement was 20 psi, as specified at 30 CFR 75.335 (2005). New emergency temporary standards for seal designs were promulgated on May 22, 2007, with a minimum requirement of 50 psi under specified conditions. However, it will be shown that the evaluation of the polyurethane seal performance as designed to meet the older 20-psi criterion can be relevant to the design requirements under the new standards.

Jan 1, 2008

By N. Kumar Kittusamy

Operators of construction equipment perform various duties at work that expose them to a variety of risk factors that may lead to health problems. A few of the health hazards among operators of construction equipment are: (a) whole-body vibration, (b) awkward postural requirements (including static sitting), (c) dust, (d) noise, (e) temperature extremes, and (f) shift work. It has been suggested that operating engineers (OEs) are exposed to two important risk factors for the development of musculoskeletal disorders: whole-body vibration and non-neutral body postures. Method: This review evaluates selected papers that have studied exposure to whole-body vibration and awkward posture among operators of mobile equipment. There have been only few studies that have specifically examined exposure of these risk factors among operators of construction equipment. Thus other studies from related industry and equipment were reviewed as applicable. Conclusion: In order to better understand whole-body vibration and postural stress among OEs, it is recommended that future studies are needed in evaluating these risk factors among OEs.

Jan 1, 2004

By J. F. Barkley

To aid in winning the recent world war, the Bureau of Mines conducted a National Fuel Efficiency Program, directed to commercial plants throughout the Nation, to save greatly needed fuel, a basic resource vital to industrial production. In planning this program it was realized that to accomplish a satisfactory reduction in fuel consumption in any plant, it would be necessary to reach, enthuse, and usually educate to some extent the actual operators of the various types of plant equipment. A major part of the programs consisted, therefore, of visits to plants and work with the operators, including a review with them of their operating conditions and of educational and guiding literature pertinent to the operating problems involved. Through a Nation-wide organization, local volunteer engineers served in making visits to local plants. Each cooperating plant appointed an employee as the "waste chaser," who headed the work of saving fuel in that plant. The educational literature was designed to interest the operator, as well as serve as a guide in eliminating waste of fuel. Volumes have been written on many subjects relating to the saving of fuel. Writings of the treatise type contain considerable good information but do not have wide appeal and probably will be read only by a few studious operators. The problem is not one of getting clown on paper everything that the experts know and would like to have the operator know, but rather to write something that will actually interest the operator and stimulate him to action. Past experience led to the adoption, therefore, of the "quiz-sheet" type of writing, using a quiz sheet of not more than two pages for any principal item. The results obtained during the National Fuel Efficiency Program in many types of plants further demonstrated that the short quiz sheet is satisfactorily appropriate and does accomplish results. Each sheet was prepared and checked by many engineers expert in the particular subject matter of the sheet. Committees of men with much experience in the manufacture and operation of equipment and in the

Jan 1, 1947

By E. P. Youngman

Titanium ranks as one of the more abundant elements, is widely distributed, and occurs in concentrated form in numerous deposits. This substance was discoveres 140 years ago; but despite the efforts of metallurgists and chemists to find a place for it in industry, only within the last 10 or 15 years has the increased use of titanium pigments provided any extensive outlet for titanium ores. Even to-day titanium is confined to a few highly specialized industrial applications. The metal itself is now quoted regularly in trade journale, but scarcely yet can it be said that the production or use of the metal. has progressed very far beyond the laboratory stage. Ferroalloys containing the element were largely used for a time, especially in connection with the manufacture of Bessemer steel rails; but as American rail- ways adopted open-hearth rails in preference to Bessemer rails, the demand for the alloys in the rail manufacture gradually dwindled into insignificance. New outlets for ferrotitanium have been found in the steel industry; and the production of titanium alloys, both in the United States and in Europe, has increased in recent years. By far the largest use of titanium at the present time, however, is in pigments. The manufacture of titanium white began in Norway, but at present the United States is the leading producer. One of the two companies now operating in the United States is also the leading factor in European production. Although titanium occurs, in many minerals, the principal commercial sources are rutile (the natural oxide, Ti02) and ilmenite (iron-titanium oxide, FeO. TiO2). The latter is a coal-black mineral, but it is the one used in the manufacture of the titanium white of commerce, as well as in the manufacture of ferroalloys and arc-lamp electrodes. Rutile, the natural oxide, is not pure white and, being less common in nature, costs more; it is, therefore, reserved for use in the manufacture of titanium chemicals employed in relatively small amounts in dye works and bleacheries and for sundry minor purposes. This paper summarizes the titanium industry, with special reference to its economic aspects. It is offered as a survey of current trade literature and as a digest of material in the files of the bureau and is presented in response to numerous inquiries from prospective producers as to ways and means of exploiting deposits. (At present, much of the ilmenite consumed in this country comes from overseas, principally from British India..). A forthcoming circular, devoted to deposits of titanium-bearing ores, deals with foreign and domestic sources of supply.

Oct 1, 1930

By Donelson A. Robertson

Includes a review of the state-of-the-art of explosives loading in the crushed stone and cement industries of South Florida and the development of a field test program for alternatives. Emphasis is on the loading of small diameter (2 1/4" or less) explosives. Test results ire evaluated for operational and economic feasibility. Details are described of an explosives loading method which involves placing cardboard tubes with external couplings through the hollow drill steel and then Loading explosives into the tube casings after the drill rig has moved off. This method eliminates the hazards peculiar to loading explosives Through the kelly bar. The alternative method can be performed by existing drill rigs with or without minor modification. With modification, improvement in yield per blasthole and/or primary crushing rate provides opportunity so offset some or all of the additional cost.

Jan 1, 1978

By L. C. IlsLey, E. J. Gleim

Electrical apparatus because of its flexibility and its adaptability to all classes of service has become essential to the mining industry. Hence the problem of providing electrical equipment that is safe for use in explosive mixtures of methane and air is of prime importance in coal mining. Ilwestigatorsand experiment stations early recognized this fact and much work has been done in the investigation and the development of electrical apparatus for use in atmospheres containing fire damp. The term "fire damp" as applied throughout this bulletin means an explosive mixture of methane and air. Direct-current motors and alternating-current motors of the slipring type when running usually give off electric arcs or flashes that will ignite fire damp. Other 'motors that ha,'e no moving electric contacts may become dangerous through accident, deterioration, or neglect. Auxiliary apparatus such as fuses, switches, rheostats, and controllers may arc, flash, or become heated to snch a degree that fire damp can be ignited. Such equipment is still more dangerous when worn or out of repair. In the United States the development of apparatus for use in gaseous mines has been associated largely with coal-cutting equipment run by electricity. This is undoubtedly due to the use of such equipment at the face of the mine workings, where the chance of igniting fire damp is necessarily greatest. One American manufacturer built a coal-cutting equipment of the totally inclosed type for use in firo damp atmospheres in 1903. Another built similar equipment with special protective devices in 1906, for export. During the years 1910 and 1911, the Bureau of Mines at its Pittsburgh experiment station conducted a preliminary investigation of the safety of such protection as was then in use or under consideration. Five motors were submitted for this investigation, each having somewhat different methods of protection. The results of this investigation were published in Bulletin No. 4G.a

Jan 1, 1920

By R. F. Chaiken

The Bureau of Mines has conducted a study of mine fires in the Anthracite Region of Pennsylvania to determine the most effective approaches to fire control in this area. The problems involved in controlling an anthracite fire include the geological and mining conditions in this area, the propagation characteristics of anthracite, the fire control methods available, the hazards associated with these fires, and the mar-ginal effectiveness of past fire control projects. From this genecal background, fire control options were discussed as they apply in ISBO to the Centralia mine fire. Probable effectiveness, feasibility, and costs were assessedv The options evaluated include four excavation plans, flooding, hydraulic flushing, water curtain isolation, mining to construct an underground carrier, burnout control, and relocation of the community. The most advantageous from a technical viewpoint is an excavation method combining complete excavation of the fire zone within the borough with trenching to confine the remaining fire. It appears that for many anthracite fires, as for the Centralia mine fire, there are no available control measures that have a moderate cost, are proven effective, and produce minimal disruption on the surface.

Jan 1, 1983

By H. Reginald Hardy

This report is Volume I of a three volume final report on the micro-seismic monitoring of a longwall coal mine. Volume I deals for the most part with the detailed aspects of the microseismic field study itself, however, brief references are made to other secondary studies described in Volumes II and III. During this field study a mobile microseismic monitoring facility and associated transducers were employed to detect and record microseismic activity above a longwall panel at Greenwich Colleries, Barnesboro, Pennsylvania. The fundamental objectives of this study were (1) to evaluate the feasibility of detecting microseismic activity originating from longwall mining operations using an approximately planar, near-surface, geophone array installed above the longwall and (2) to attempt to locate the sources of the various microseismic events. This investigation has proven that, using the techniques developed it is possible to detect microseismic events at depths of more than 400 ft and at horizontal distances in excess of 800 ft from the source. The majority of the observed events were found to have frequencies on the order of 10 to 100 Hz, and particle velocities of 50 to 300 µips. When a suitable velocity model was utilized, most of the events located were computed to be within ±100 ft vertically of the coal seam and ±50 ft horizontally of the longwall face. The results of the overall research project suggest that additional research should be undertaken in a number of associated areas.

Jan 1, 1978

By J. D. Lane

The U.S. Bureau of Mines is conducting research on guidance systems for computerized haulage in underground mines. This report describes the process of component selection, installation and testing, perception algorithm development, and steering control algorithm development, to produce a real-time steering control system for an articulated haul truck for underground mining. Ultrasonic transducers were mounted on the truck to provide perception data by measuring the distance to the ribs. Linear potentiometers mounted inside the steering cylinders measured the steering angles. Algorithms, implemented on an inexpensive, robust onboard computer system, analyzed the data and controlled the steering via an electro-hydraulic proportional valve. The steering algorithm presented follows a zone defined by the relative position between the truck and a rib. Experimental verification of the ability to follow the zone in a test corridor on the Colorado School of Mines campus is presented. The automatic steering system successfully negotiated straight sections, curves, and the transition zones between straight and curves with the truck in first and second gears. The resulting real-time automatic-steering system can be applied to many underground articulated machines.

Jan 1, 1994