Search Documents

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the .Oklahoma Planning and Resources Board of the Conservation Commission has been authorized4/ to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By Steven J. Page, Andrew B. Cecala, John A. Organiscak

In This Chapter [Drill dust control: wet and dry Enclosed cabs on drills and mobile equipment Haul road dust control] Overburden drilling generates most of the respirable dust that affects workers at surface mines. Both wet and dry methods are available to reduce this drill dust. Overburden removal by mobile excavation equipment such as bulldozers, front-end loaders, and haulage trucks can be dusty, particularly under dry and windy conditions. Tightly enclosed cabs with dust filtration systems can substantially lower the dust exposure of both drill and mobile equipment operators. Haul road dust control can be achieved by water application or chemical application. DRILL DUST CONTROL [Drill dust is controlled with wet or dry systems. Wet systems can be more efficient, but may freeze in the winter. Dry systems require careful maintenance of the drill deck shroud. An improved deck shroud is shown.] Wet Suppression. Wet drilling systems pump water into the bailing air from a water tank mounted on the drill. The water droplets in the bailing air trap dust particles as they travel up the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole [Page 1991]. In wet drilling systems, typical water flow rates are 0.1 to 2.0 gpm depending on the size and type of drill and the moisture level of the overburden. The drill operator controls the flow using a control valve located in the cab. Some drills are equipped with a flow meter to give the opera-tor a visual sign of the flow rate. Raising the water flow will improve dust capture, but too much water causes operational problems. Because of this, the drill operator must exercise care in find-ing the best water flow rate.

Jan 6, 2003

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

By J. K. Richmond

This is a progress report summarizing more than 5 years of a long-range Bureau of Mines research program. The purpose of this program has been to investigate the fire and explosion properties of Green River oil shale in the Bureau's Experimental Mine, in laboratories, and in the field. The lean limits of explosibility of oil shale dust, by small-and large-scale tests, are reported as a function of grade, ignition source, and particle size. A limited number of laboratory tests on the autoignition of oil shale dust layers and the spontaneous combustion tendencies of oil shale are described. Moderate-scale rubble fire tests were conducted to determine flame spread rates as a function of ventilation flow. With the aid of a system to continuously monitor methane emissions in a deep oil shale mine, the characteristics of the methane flow are reported as a function of ventilation and blasting procedures, and are compared with gas yields from core samples. Tentative predictions as to the emission of the methane to be expected in deep oil shale mines, far from the outcrop, are offered. Brief reference is made to a parallel investigation into the fire and explosion hazards of oil shale mining and processing by a Bureau contractor; detailed results of the latter investigation are to be found in the contractor's reports.

Jan 1, 1982

By R. G. Gürtunca

Over the past century coal miner safety and health has seen tremendous improvements, the fatality and injury rates continue to decrease while productivity continues to increase. Many of the hazards that plagued miners in the past, such as coal bumps, methane and coal dust explosions, ground fall accidents and health issues have been significantly reduced. The contribution of NIOSH research includes products for prevention and survival of mine fires, methane control measures, design procedure for underground coal mines, methods for excavation surface controls, methods and procedures for blasting, laser usage in underground mines and prevention of electrocution from overhead power lines that have reduced accidents and injuries in underground coal mines. Health research has produced products such as the personal dust monitor, noise abating technologies and ergonomic solutions for equipment operators. Research priorities at NIOSH are set by considering surveillance statistics, stakeholder inputs and loss control principles. Future research in coal mining is directed towards respiratory diseases, noise induced hearing loss, repetitive musculoskeletal injuries, traumatic injuries, falls of ground and mine disasters. The recent spate of accidents in coal mines resulted in the Miner Act of 2006 which includes a specific role for NIOSH in future mine safety research and development. The mine safety achievements in the USA reflect the commitment of industry, labour, government and research organizations to improving the safety of the mine worker.

By John W. Sweeney

The southeastern phosphate industry is investigated to determine its role in supplying the United States and world phosphate demand. The report shows that the southeastern (Florida, Tennessee, and North Carolina) phosphate industry is the leading domestic and world producer of phosphate rock, The report emphasizes size and organization, production capacity, transportation, and marketing of the southeastern phosphate product, Factors affecting the supply- demand relationship of the southeastern phosphate industry and world phosphate production-consumption relationships are analyzed and related to the southeastern phosphate industry. Past trends are projected and the future role of the southeastern phosphate industry is analyzed to determine its ability to supply the United States and rest-of-the-world phosphate requirements in 1985 and 2000. The projections show that southeastern resources are ample to supply domestic and export requirements at the projected rates of consumption well beyond the year 2000.

Jan 1, 1970

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the low funding level program plan.

Jan 1, 1980

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission In metal/non-metal mines over a wide frequency range from 0.2 -1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types Include 01 f shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most Important mining techniques. The results show that transmission at medium frequencies are optimum tor wireless mine communications, In agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 1, 1981

By Donald R. Johnson

Apparatus providing simultaneous differential thermal analysis, thermo-gravimetry, and evolved gas analysis, has been developed by the Bureau of Mines specifically for thermal study of oil shale and other solid, natural fuels. The apparatus is described in detail, and simultaneous analyses on a single sample of an oil shale mineral, nahcolite, and a thermal analysis demonstration compound, calcium oxalate monohydrate, are presented to demonstrate the instrument's capabilities.

Jan 1, 1970

By J. Koster

[Boron is an element whose metallurgical possibilities never have been investigated thoroughly, probably because of the difficulties experienced in the preparation of elemental boron and its intermetallic compounds. The southwestern United States contain the world's s largest deposits of boron minerals. In general, the mineral is readily available, and mining costs are not excessive. The most important boron mineral of commerce is borax (sodium tetraborate) however, there are large deposits of colemanite (a mineral having the composition represented by 2CaO 3B2O3 5H2O) in Clark County, Nov. This material was worked in times past by converting it to sodium tetraborate. In recent years the deposits have laid idle because of a mire readily available source of borax in the old lake beds of California.]

Jan 1, 1940

By T. M. Barczak

A primary objective of the Bureau of Mines geomechanics research program is to develop a better understanding of support behavior and interaction of supports with the strata so that supports can be more closely engineered to the geological conditions in which they are employed. Four longwall shield supports were instrumented with an eight-transducer instrumentation array to measure leg, canopy capsule, and compression lemniscate link forces from which resultant shield loading was determined. The instrumented supports were monitored over a 4-month period, producing over 75 shield cycles of resultant shield loading. Resultant loading is the true measure of support resistance, providing both roof-to-floor and face-to-waste support reactions as well as the location of the reaction on the shield canopy. Observed roof support reactions were analyzed, with particular emphasis on horizontal shield loading, since it is the least understood design parameter. Average, peak, and change in shield loading during the mining cycle are discussed. Correlations among data parameters are examined, as is the distribution of support loading at the headgate and midface. Conclusions are drawn as to the effectiveness of the shield support at this installation. Recommendations are made for further research needs.

Jan 1, 1987

By C. J. Bise

One area of study for the Coal Mine Injury Analysis project was to illustrate how loss control can be used as a foundation for mine safety training. After an initial review of the principles of loss control, the instruments often used for worker/worksite appraisal, such as incident reporting, analysis, and investigation, workplace observation, worksite inspection, and safety audits and checklists were evaluated for their effectiveness. The findings were then applied to the continuous-miner worksite at several mines to modify the techniques for use in a highly dynamic man/machine work environment. Before the information gathered from the review of the various continuous-miner worksites was presented at the annual retraining sessions at five mines, a trainability analysis procedure was developed to separate training shortcomings from those problems resulting from improper equipment design or unsatisfactory working environments. Also, several microcomputer-based training programs were developed to aid in conveying the loss-control concepts to the trainees. Finally, the results from the implementation and evaluation of the loss-control-based training programs were documented, including the complete training script for one of the case-study mines. The procedures outlined in this study will aid mine training specialists in developing focused, pro-active accident-prevention strategies and training programs that are based on sound loss-control principles.

Jan 1, 1993

By W. W. Adams

"The eighth National Safety Competition, that for 1932, conducted by the United States Bureau of Mines, was participated in by 322 mines and quarries operating in 34 States. Tables 2 to 6 show the relative standing of the various plants. Bronze trophies, known as the 'Sentinels of Safety,' which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were awarded to five companies, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, - namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or open-cut mines. The trophies are awarded for one year and are then transferred to the winners of the succeeding year's contest.The trophy for bituminous-coal mines, which has been in New Mexico for the past year, was won by a mine in West Virginia. The metal-mine trophy goes to New York State for the first time in the history of the contest. Previously it had been won by mines in Minnesota, Michigan, Kansas, and Oklahoma. The trophy for nonmetal mines remains for another year at Retsof, N. Y.; that for quarries and open-cut mines is transferred to a quarry in Michigan. The trophy for anthracite mines, of course, remains in Pennsylvania, as all anthracite mines in the contest are in that State.In determining the relative standing of the various companies enrolled in the competition, all mines and quarries were graded according to their accident-severity rates, - that is, according to the number of days of disability of employees on account of accidents in proportion to the number of man-hours of work done by all employees at the plant. Reports of accidents and of man-hours worked were furnished by the companies to the Bureau of Mines. These reports were carefully examined and classified to insure uniform weighting of accidents according to the number of days of disability to be charged and to insure uniformity of methods of calculating the accident-severity rates for the various mines and quarries. When the relative standing of all plants had been determined in this way, a summary of the records of the companies having the lowest accident-severity rates in their respective groups was sent to the members of a committee of award for examination in accordance with the rules governing the safety contest. The members of the committee of award were W. H. Cameron, managing director of the National Safety Council; William Green, president of the American Federation of Labor; James F. Callbreath, secretary of the American Mining Congress; T. T. Read, Vinton professor of mining engineering of Columbia University; C. B. Huntress, executive secretary of the National Coal Association; A. J. R. Curtis, assistant to the general manager of the Portland Cement Association; and A. T. Goldbeck, director of the bureau of engineering of the National Crushed Stone Association. When two or more mines within the same group operated without an accident during the year, the contest rules provided that the trophy for the group should be awarded to the plant whose record showed the largest number of man-hours worked."

Jul 1, 1933

By E. P. Ferrero

Crude oils from fields throughout the world are analyzed by the Bureau of Mines to determine the characteristics of the oils and their contribution to the petroleum resources of the world. Analyses are reported for 169 foreign crude oil samples from 122 oilfields in Africa, Asia, Australia, the Caribbean, Europe, North America, and South America. Tables show the geographic and geo- logic origin of the samples, names of companies that supplied the samples, annual production for the fields, general characteristics and analytical and computed data, hydrocarbon-type data, cumulative production of the larger fields, and references to sources of geological and field development information. The analyses were made by the Bureau of Mines routine method and comparisons may be made with more than 8,000 other such analyses.

Jan 1, 1972

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

By David White

This paper is the result of a comparative study of ultimate coal analyses made and published by the United States Geological Survey. This study, at first casually undertaken to devise an acceptable classification of coals based on chemical analyses, was continued in connection with a microscopic examination of a number of the coals. The initial comparisons, made from a relatively small number of analyses, not only confirmed a previous conviction that the elimina- tion of oxygen incident to the development of a coal is economically far more important than has been generally suspected, but also showed that oxygen is very nearly as harmful as ash in coal. The immediate purposes of the present study were: (a) To deter- mine more definitely, from a comparative examination of a large number of ultimate analyses, the relative importance of oxygen as an impurity in various coals; (b) to illustrate the transition between various grades of coal of similar origin-transition mainly due to progressive devolatilization, brought about more or less directly by dynamic influences; (c) to ascertain the relative proportions of oxygen, hydrogen, and carbon in coking coals, especially with refer- ence to a theory tentatively framed to explain the coking quality; and (d) to forecast the probabilities of successfully treating a large number of coals so as to render them amenable, in a softened condition, to satisfactory study under the microscope. Although the hypothesis as to coking quality finds but partial support in the chemical analyses, its consideration has led to a method of predicting from an analysis with a fair degree of certainty whether any given coal will coke by the ordinary process. The unbroken transition between coals originally similar but now classed in widely different groups, whether of the same age or of different ages, as a result of dynamochemical action, appears demonstrated by the analyses as well as by field observation. This subject will not be

Jan 1, 1911

By W. M. Deaton

The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but mere limited study of this type was conducted by engineers of the Bureau of Mines a number of yours ago.4/ A summary of the earlier findings was included in a general report by the Bureau on the flew of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines.

Jan 1, 1941

By Franklin D. Cooper

This Bureau of Mines report reviews in detail the foundry coke situation in the United States in 1975. It discusses intrinsic production problems and identifies opportunities for modifying operating practices so that the quality and yield of foundry coke can be enhanced without unnecessary investment in new equipment. Major topics include operating data and attendant practices and problems, the relationship of carbonization phenomena to coke quality and yield, environ- mental impacts of foundry coke plant operations, suggested research and development opportunities, and data on components of oven charges and on foundry coke production and shipments.

Jan 1, 1977

By Miyuki Morioka, Michael J. Griffin

Discomfort, annoyance, or interference with activities due to exposure to vibration is only expected if the vibration exceeds the threshold for the perception of vibration. When there is more than one vibration input to the body (e.g. at the hands, seat and feet), the sensation is first experienced at the location with greatest sensitivity. Knowledge of differences in the thresholds of perception for vibration at the hand, seat, and feet should assist the identification of sources of discomfort caused by vibration. Perception thresholds for vibration have been determined in several studies, but only a few studies have investigated perception thresholds in the horizontal direction for hand-transmitted vibration 1, 6 or whole-body vibration 4-5, and there has been little consideration of perception thresholds for the foot resting on a vibrating surface. This study determines absolute thresholds for the perception of sinusoidal lateral vibration, examining the effect of vibration frequency (8 to 315 Hz for the hand and foot; 2 to 315 Hz for the seat) and the effect of input location (the hand, the seat and the foot). Methods Three groups of twelve males aged between 20 and 29 years participated in the experiment. Subjects in each group attended an experiment to determine perception thresholds for lateral vibration via either a rigid handlebar (30 mm diameter) at the left hand (left hand), or a rigid contoured seat (250 mm x 150 mm), or a footrest at the left foot (30.5 mm x 10.5 mm with 10-degree inclination). For the non-exposed hand (right hand) or foot (right foot), a stationary handle and footrest with the same dimensions as the vibrating handle and footrest were provided so that the same body posture was adopted among the three groups of subjects. An up-down (staircase) algorithm was employed to determine thresholds in conjunction with a three-down one-up rule. A single test stimulus (2.0 seconds) was presented with a cue light illuminated during this period. The task of the subjects was to indicate whether they perceived the vibration stimulus or not. The threshold was calculated from the mean of the last two peaks and the last two troughs, omitting the first two reversals. Results The median absolute thresholds of the 12 subjects determined at each frequency for the hand, seat and foot are shown in Figure 1. A frequency dependence of the threshold contours within the investigated frequency range is evident, with similar shape to the threshold contours

Jan 6, 2006