Search Documents

By Lars Osen

Both fragmentation and safety can be improved by following proper procedures in loading boreholes. Proper loading procedures such as primer location, borehole sealing, decking, and stemming along with the hazards of dropping on primers are presented. Discussions follow on the reason for the use of each procedure along with the possible consequences such as hazards, misfires, or poor fragmentation.

Jan 1, 1985

By C. Heiss, A. Hofmann

Due to an explosion in an Austrian steel works during the basic oxygen process, the Chair of Mining Engineering and Mineral Economics at the Montanuniversitaet Leoben was assigned with the set-up of a test arrangement to study the effects of large-scale particle emissions on the plant´s installations and the testing of various structures and structure-combinations to be applied as explosive-proof enclosure.

Jan 1, 2012

By R R. Singh, U K. Dey, S K. Roy

"Commercial explosives being a heterogeneous mixture of many chemical compounds in prefixed proportion, their velocity of detonation (VOD) may vary from batch to batch, due to variations in the proportion of the chemical composition and process parameters even within their tolerance limits. Inherent limitations of measuring methods and human variations during measurement also add to the variation in VOD values determined practically. Therefore, it is customary to define a range of VOD values rather than a fixed value of VOD for a particular explosive.Variations in VOD values of four commercial permitted explosives in India were evaluated under open unconfined condition using Dautriche method and a resistance wire method based continuous VOD meter. Comparative evaluation of VOD values of selected explosives were aimed to check the relative effectiveness of continuous VOD measurement of small diameter cartridged permitted explosives using cheaper co-axial wire instead of recommended costly VOD rods along with the continuous VOD meter. Results of evaluation revealed that continuous VOD of commercial small diameter cartridged explosives could be determined using cheaper co-axial resistance cable with comparatively better accuracy than the most commonly used Dautriche method."

Jan 1, 2007

By Alton Dunaway, Kevin Sullivan, Charles Gray, Doug Hall, Kevin Grant, Kelly Thiel, John Paulson, Bruce Leland, Cole Boyd

Beaver (Castor canadensis) are responsible for economic losses exceeding $4 billion over the last 4 decades in the southeastern United States alone. A large portion of these damages occurs to public roads and highways, forests, agricultural resources, and other property from flooding caused by beaver dams. The United States Department of agriculture, Animal Plant Health Inspection Service, Wildlife Services (WS) program is a non-regulatory Federal program directed by Congress to assist resource owners with managing damage caused by wildlife.

Jan 1, 2007

By Jaco van den Berg, Dr. Todor Petrov, Dr. Josh Calnan, Dr. Jhon Silva

This paper shows and reviews the similitudes and differences in explosions generated by high explosives and gas explosions, the reasons why gas explosions are difficult to replicate using high explosives, and the considerations when performing explosive testing using methane gases and coal dust.

Feb 1, 2020

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In-hole detonation pressure measurements are unusual in the production environment of a mining operation, partly owing to the hostile conditions to which recording equipment and pertinent probes must be subjected and, partly by the constraints of the production cycle. In recent decades, detonation pressure measurement techniques have been developed using low carbon resistors (LCR)-based gauges. They are cheap, relatively easy-to-operate, robust and with a high percentage of success in both open-pit and underground mining. Detonation pressure measurements are extremely important when carrying out numerical modelling to simulate explosive induced vibrations, since simulation results are highly dependent on the pressure-time history applied on the blasthole wall. Analytical equations have typically been used to model the pressure-time history; however, they usually do not adequately represent the behaviour of the explosive in terms of: peak pressure reached, rise time, mean frequency, decay and shape of the signal. Experimental records may be directly used instead of utilizing synthetic signals if they are available. In this work, (LCR)-based gauges are used to measure detonation pressure inside a production blasthole. The operation principle of the gauges utilized and the instrumentation layout is described in detail. A flexible resolution USB oscilloscope with high sampling rate has been used to catch the elusive pressure peak event. Measurements were carried out in production blasts fired with ANFO (0.86 g/cm3) in an underground mine––this also includes velocity of detonation (VOD) records––. A procedure based on the shock impedance matching has been developed to calculate the detonation pressure due to the characteristics of the gauges prevent its direct measurement. Detonation pressures obtained range from 1.71 to 2.97 GPa (248.01 to 430.76 ksi) which are in line with pressures calculated from the VOD records. Mean frequency and rise time analysis shows that 2 of 3 signals cannot be described using typical analytical equations.

Feb 6, 2023

By Tony Francelj, D. Scott Scovira, Remi Proulx

The Meikle Mine is a high-grade, underground gold mine that utilizes a primary and secondary stoping method with delayed backfill. The newly developed Rodeo Mine will start production using similar mining methods in late 2001. The combined production for the mines will be 4100 stpd of ore in 2002. Dilution of the secondary stopes resulting from blast induced overbreak of the backfill placed in the primary stopes was an issue identified as being a major contributor to the total mining cost at the Meikle Mine. To address the overbreak issue, a low-density, polystyrene enhanced bulk emulsion was developed and introduced to the mine. The density and energy of the emulsion was varied until an optimal level was reached. The use of a low-density bulk emulsion has greatly reduced the overbreak of the primary stope backfill when blasting the secondary stopes. Benefits to the mines include reduced secondary stope dilution, lowered total mining cost, and increased revenues.1

Jan 1, 2002

By Bruce R. Leland, Steven H. Smith, John D. Paulson

The USDA - Wildlife Services has been removing beaver dams with explosives for over 30 years. This paper will discuss the history of the explosives program, summarize how we've evolved, and highlight our work removing beaver dams in unique locations.

Feb 1, 2020

By Travis Davidsavor, Stanley: Dong Vitton

Concrete is a common construction material used throughout the world, and with increasing demand of fast-track construction, blasting and concrete casting are occurring simultaneously at many sites where rock is being excavated for concrete placement. However, there has been significant disagreement in the construction industry as to what intensity of shock vibrations green, or fresh concrete can tolerate. Peak particle velocities are often arbitrarily chosen, or are simply based on materials such as plaster and drywall that have been more thoroughly studied in relation to damage. Previous research on green concrete has used the concrete’s static strength subjected to shockwaves at different ages as the primary damage criteria. In addition, the static strength tests have been based on curing time. However, changes in temperature or humidity can dramatically alter the hydration rate, which affects strength development of different cements. To account for temperature changes and humidity the concept of concrete maturity is commonly used and allows the researcher to see where the concrete was in terms of hydration progress. In general, static testing determines the failure stress that the concrete’s macrostructure can handle, and often failure occurs in the natural materials first or along large defects in casting techniques. Dynamic testing or high strain rate testing, on the other hand, loads materials at such a high rate that larger defects do not have time to react and instead the microstructure is more highly stressed leading to higher strength and stiffness values. This is known as the material’s strain rate sensitivity. Since dynamic testing better tests the microstructural strength, it is believed that it may provide a better way to assess damage to green concrete. Testing includes both static and dynamic compression as well as static and dynamic splitting tensile strength to assess whether damaged has occurred to the concrete. No significant statistical evidence was discovered that damage to the concrete occurred at five different “green” maturities from peak resultant velocities ranging from 10.66 in/s (271mm/s) to 4.40 in/s (112 mm/s) with average intensity of 6.7 in/s (170mm/s).

Jan 1, 2003

By Daniel Scott

Mines have used explosives for economical fragmentation for many years. It can therefore be expected that the mining industry has thoroughly researched how to achieve the most efficient blast. However, there is still a large amount of iteration that must be undertaken before blasting at a mine site can be refined enough to allow for consecutively successful blast results. And then the geology changes. This paper will present an approach to blast design that considers production goals, geology, budget, and safety, and will contrast the proposed method with well established blasting theory.

Jan 1, 2012

By Alexander Hauck, Dimitri Jung, Uli Leiste

This paper describes results from small scale tests conducted to determine the distribution of impulse on target plates when subjected to loading due to the detonation of a buried mine. The tests were conducted with saturated sand, dry sand, and water as the loading media. Tests were conducted for flat plates and for plates with angled bottoms. Previous testing has shown that angled bottoms can reduce the total vertical impulse delivered to the vehicle significantly. Different stand off distances were investigated as well as loading of the targets both on center and off center. It is very important to know not only the total impulse delivered by a detonating charge but also how this impulse is distributed over the bottom of the vehicle. A complete understanding of specific impulse will permit those parts of the vehicle, taking the greatest amount of loading, to be sized properly. Experimental results were compared to analytical expressions provided by Westine and Tremblay.

Jan 1, 2010

By C E. Johnson, S Hosein

Previous researchers have put forward two different theories as to the origin of air overpressure from quarry blasting. In 1980, Siskind et al postulated that the initial face movement gave rise to the displacement of air and that this resulted in the air overpressure pulse. However in 1990 McKenzie et al carried out research that indicated that the air overpressure pulse came into being as a consequence of the shock wave created by the detention of the explosive charge in a blast hole. In an attempt to evaluate these hypotheses, an investigation was undertaken over a 4-year period with the aim of determining the precise origin of air overpressure. The research was carried out at a chalk quarry in the North of England.

Jan 1, 2017

By Ashlin Pillay, Osamu Iwata

Hong Kong is ranked as the world’s third most important international financial hub and attracts significant growth and development annually. The city is also known as the world's most vertical city, the most common view from your window in Hong Kong city centre is probably the window of another 30 storey skyscraper. The increasing demand for real estate in this bustling Metropolis has placed immense pressures on its transportation infrastructure because whilst the construction continuously grows upward with larger and larger skyscrapers, it leaves the transportation planners with very little choice but to go underground. As a first world city, interrupting daily business operations is simply not an option; however, of even greater concern is the safety of these 8 million residents. Blasting Regulations are under the strict control of the Mines Division showing zero tolerance to the breaching of safety standards. The Ho Man Tin Station (HOM) excavation, a part of the Kwun Tong Line Extension (KTE) project situated in Hong Kong began in June 2012 and is one such project that is under strict regulations from the Mines Division. The HOM project is a cross cut interchange station between the Kwun Tong Line Extension (KTE) and Shatin Central Link (SCL).

Jan 1, 2015

By David Scutt, David Noon

Blast crews are exposed to a number of major hazards including explosives and chemicals, ground conditions, machinery, unique work environments and specific blasting hazards such as fly rock and misfires. Unfortunately, injuries caused by sudden and/or unexpected movement of ground are continuing to occur. Blast crews are not equipped with the knowledge or tools to understand whether a high wall that they are planning to work under is safe.

Jan 1, 2011

By Bin Feng, Xiang Fang, Tao Guo, Fandong Lu

Abstract: Rough set theory (RS) can find useful information from a large number of data and generate decision rules without prior knowledge. Support vector machines (SVM) have good classification performances and good capabilities of fault-tolerance and generalization. To effectively control blasting vibration effect, prediction model of blasting vibration parameters based on rough sets and support vector machines are established. Particle swarm algorithm (PS) is used to dynamically discretize attributes. Then, according to the optimal particle calculated by the PS algorithm, the decision table is established. After eliminating less importance attributes and data, then SVM is trained and established for prediction. The model can deal with both quantitative and qualitative factors such as aperture and cast direction, and analyze their importance to peak vibration acceleration value. The improvement of prediction accuracy is verified by testing data.

Jan 1, 2014

By Doss Brittain

The term ground breaking is taken to include the process of so loosening the ground as to enable it to be readily loaded into buckets or cars and hoisted from the shaft or drift. In the Joplin district are encountered two varieties of ground, the hard and the soft. Hard ground consists of massively bedded rock requiring heavy blasting to loosen it. Such ground is to be found throughout the district in the same localities as the soft ground but more extensively, even to the exclusion of the appearance of soft ground in the sheet formation in the vicinity of Webb City. The Yellow Dog Mine at Webb City and the Grace mine on the Granby land at Joplin furnish well known examples of hardground mining which has become the most extensive in the district.

Jan 1, 2008

By N. Rouse

Underground raises and slots are a vital part of underground blasting operations. Raises and slots are vertical shafts or openings used for ventilation, ore passes, or creating voids in stopes. In the author’s experience, raise and slot designs can vary significantly from operation to operation or even within a single operation, sometimes for reasons unknown. The results of the various designs can differ depending on drilling accuracy, geology, and the explosives used in the design. The purpose of this paper is to summarize the recommendations found in published literature on raise and slot design in one document, while incorporating some of the author’s own experience with optimizing raise and slot designs in underground operations. Some inspiration is also included from burn round designs; small versions of raises drilled horizontally in development blasting rounds. This document includes discussion points on drillhole diameter and depth, pattern design and relief requirements, explosive types and loading recommendations, and timing. Ultimately, this document can be useful to those looking to design a raise or slot blast for the first time or for those looking to improve on the results from the raise and slot blasts used at their operations.

Jan 1, 2024

By Wendell W. Harris, Stanley J. Vitton

In the United States each year it has been estimated that expansive soils cause approximately $9.0 billion in damage to buildings, roads, airports, and other facilities. This figure alone exceeds the damage estimate for earthquakes, floods, tornadoes, and hurricanes combined. Unfortunately, some cases of expansive soil damage (swelling) are blamed on rock blasting operations if the blasting operations are located within the immediate area. While simple tests, such as the Atterberg limits test, can characterize a soil as expansive, it does not necessarily answer the question whether the foundation soils are causing distresses to a structure. In particular, it appears that once a soil has been labeled as nonexpansive it is no longer considered as a problem soil, in which case blast vibrations become the prime suspect.

Jan 1, 1996

By Calvin J. Konya

For proper blast design, one must make the assumption that all blastholes release nearly ideal energy. In many types of blasting operations, blastholes release very little useful energy. These blastholes are called malfunctioning blastholes. Recent studies indicate that as many as 30 percent of all blastholes are malfunctioning. These malfunctioning blastholes are not an unusual occurrence.

Jan 1, 1988

By Gerald G. Schmitt, Richard D. Dick

Continuous Reflectometry for Radius vs Time Experiments (CORRTEX) was used to monitor several conditions of blasts such as the detonation velocity of the explosive column, the functioning of different types of initiators and initiation schemes, and the behavior of the stemming column confining the explosive. The CORRTEX data were also used to deduce the occurrence of dead pressing of ANFO slurry. Measurements of propagation speeds of shock waves in the stem column with various cables allowed some conclusions concerning bridging, stem failure, and stress levels in the stem.

Jan 1, 1985