Search Documents

By C Hunter, K Fedak, J P. Todoeschuck

"Perimeter wall control has a direct effect on the overall grade of any underground miningoperation. Mine management at INCO's Birchtree Mine in Thompson, Manitoba requiresmaximum perimeter wall control to meet high safety standards and to maximize nickel orerecovery. If footwall or hanging wall contacts are damaged by over_blasting, the ore maybe greatly diluted, mine productivity may be reduced and safety problems can arise.Excessive or poorly distributed explosive energy is a major cause of damage to the hostwall rock."

Jan 1, 1993

By Francis O. Otuonye

An application of a time series and systems analysis modeling technique to blast vibration data is discussed. The vibration data was taken from a rock support structure and the surrounding rock mass at distances close (less than 15 feet) to a blast. The analysis technique provides quantitative information on the frequencies of ground motion as well as the frequencies and damping ratios of a near-field support structure.

Jan 1, 1994

By Doug Hoy

The scope of the Cliff Avenue Reconstruction Project in Sioux Falls, South Dakota was to widen a two lane highway to five lanes, along with removing and reconstructing both above and below ground utilities located along the project limits. The objective of this paper is to present the blasting techniques used in the rock excavation phase of the Cliff Avenue Reconstruction Project.

Jan 1, 1992

By Bengt Niklasson

"A test stope at the Luossavaara Research Mine in Kiruna, Sweden,was divided into four different modules in which various hole patterns and explosives were tested in order to evaluate:1. The optimum combination of explosive and hole pattern2. The resulting fragmentation3. The damage to the surrounding rock4. The application techniques of the VCR mining method"

Jan 1, 1985

By G Alan Foster

This paper discusses the cause of air blast and modern techniques to reduce this at the source. In addition it raises the problem of their marked variability due to prevailing weather conditions and how weather data can be obtained and used in the control of air blast.

Jan 1, 1975

By R Keller, R Law

In the rush to beat the clock before the handover of Hong Kong back to China in June of 1997, an unprecedented amount of infrastructure work is being undertaken at a breakneck pace. In the middle of this construction explosion, on this island of barren granite , stands some of the most concerning and restrictive slope stability measures. So conservative, these measures impact blasting and vibration control to an extent unmatched anywhere in the world.

Jan 1, 1996

By David A. Smith, B L. Jr Lindsey

Arkansas bauxite varies enormously in its consistency and composition which makes blasting a very difficult operation. Blasting rounds have to be designed based on each particular mine's ore characteristics. The variances are so great in some mines that blasting procedures have to be changed almost daily.

Jan 1, 1979

By J S. Kuszmaul

The economic development of modified in situ oil shale retorting will benefit from the ability to design a blasting scheme that creates a rubble bed of uniform permeability. Preparing such a design depends upon successfully predicting how a given explosive will break rock. Numerical models are used to make predictions of the extent of damage caused by an explosion.

Jan 1, 1985

By Zhou Jiahan Wang Feng

This paper introduces the mechanism and the operating process of dike building by silt squeezing blasting. DBSSB (dike building by silt squeezing blasting) has the following advantages: shorter construction period (the construction period is decided only by the speed of rock materials filling)greater consolidation of the body of the dike, more structural stability, smaller settlement. Therefore by conventional standards the same dike can be designed with a smaller cross section than other construction methods, and at a reduced cost when enough rock materials can be provided in site.

Jan 1, 2006

By Stuart Brashear, Lee Schettler

"The effect of water on several ANFO/emulsion blend ratios is documented by both physicalobservations and analytical testing to demonstrate the effect even small quantities of water canhave on water resistant blends."

Jan 1, 1996

By Mark S. Stagg, Steven V. Crum

The Bureau of Mines is conducting research to develop methods to control fragmentation and improve productivity in surface mine blasting. As part of this research, PRONT02D, a two-dimensional finite element computer program developed at Sandia National Laboratories, was employed to model the fragmentation produced from RS-50, a single hole, reduced scale bench blast in a massive dolomite. The fragment size distribution obtained from the computer simulation was calculated using a submodel that utilizes the crack density and nominal flaw size values computed by PRONT02D.

Jan 1, 1989

This paper describes experience in designing and implementing casting blasts over the past fifteen years. Important design parameters such as powder factor, burden and spacing, blast pattern geometry, front row burden and toe distance, pit width versus height, blast length, explosive selection, millisecond delay timing and tie-in types are discussed.

Jan 1, 1995

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d'Or, Québec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By Ian A. Niell, Alastair C. Torrance

A joint research programme conducted by BHP Central Research Laboratories and Du Pont Wesfarmers Pty Ltd examined the effect of the size of cast primers on the run up and steady state detonation velocities of ammonium nitrate based explosives as a function of blasthole diameter. Both continuous and point to point velocity of detonation measurement techniques were used. The field trials examined a number of the Du Pont HDP series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the run up velocity of 187mm diameter ANFO charges is negligible using cast primers as small as 1509. However, emulsion and watergel explosives did exhibit run up in both 187 and 311mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blasthole diameters.

Jan 1, 1990

By J R. Brinkmann

The South African gold mining industry presently uses four different types of explosives in stope blasting. There is general agreement that the type of explosive has considerable effect on Important blasting results such as the degree of rock fragmentation, the intensity of damage to surrounding rock, and the success of break-out at the toe of the hole.

Jan 1, 1989

By B Mohanty, R Yang

Blasting vibration information is now commonly used to diagnose blast malfunctions. These range from limiting vibration levels to protect normal dwellings to determining scatter in detonator firing times, and even to rating of explosives in the borehole. Although blasting vibrations have the potential to yield reliable information in all these issues, there are key restrictions on their specific use, which are often ignored. These include all aspects of instrumentation, and sensor layout, as well as methods of analysis. This paper highlights these limitations. It emphasizes the distinction between near-field and far-field seismic recording in terms of borehole dimensions and blast geometry. Several case studies from both underground and open-pit blasting operations are discussed to illustrate and emphasize the essential characteristics of blasting vibrations and their optimal use in diagnosing blast malfunctions.

Jan 1, 1997

By Miie Shields, Ed Billington

Trail blasters for the National Park Service (NPS) live and work in remote mountain terrain throughout the western states, where any support or resupply may be sporadic and ditlicult and mountain weather affects every activity. Mechanical “aids” are the pick, shovel, rock-bar, wheelbarrow, and a Pionjar or Cobra dritl. The blaster is usually faced with an extraordinary range of work, t?om delay blasts in weathered rock using driiole depths of 18” (46cm) to as little as 4” (1 Ocm), through reducing boulders and talus fields to useable tread, blasting stumps, snags and log-jams, to the explosive disintegration and casting of animal czcasses. One day he/she might provide a 500cf (14 cu meter) anchor excavation for a suspension bridge, the next day directionally fall 60” (1.5m) diameter snags in a camp area, and the following day blast a 3-foot-wide (1 meter) tread bench across a steep bedrock slope. To be effective, the blaster must design each and every blast around desired end result, crew and public safety, maximizing effective use of limited quantities of explosive, and the minimnation of environmental effects. Since almost all drillhole blasting occurs in the weathered zone of the rock, blasting is more the art than the science of judging rock density, hardness, cohesion and prefracturing, and selecting explosives, drill and delay patterns, and loading techniques responsive to those conditions. For these reasons the NPS issues its own Blaster’s License, with a basic requirement of at least 40 hours of NPS blaster training and 3 years of supervised Blaster in-Training experience. The focus of this pre-license requirement is on safety and using explosives as a precision tool, versus just “blowing things up”.

Jan 1, 2002

By A. Lindo, M. Held

The formation of NOx fumes is an undesired occurrence and is dependent on a variety of variables. Methods for detection of such fumes with blast analysis tools are available using color schemes for grading, but no quantification tools to measure concentration and cloud totals exist today. In cooperation with DIRS (Digital Imaging and Remote Sensing Laboratory) at RIT in Rochester, NY, Austin Powder has been looking for methods and techniques to identify and quantify total amounts of NOx by capturing cloud activity via a video feed from a drone in combination with measuring NOx and subsequent cloud modeling (i.e., plume segmentation). To accurately measure fume events, Austin Powder and the RIT team have been collaborating in performing small scale blasts at an Austin test facility and then transferring knowledge learned to full scale blasts at customer sites. The collected data will allow to identify any relationships between the total amount of explosives used and the quantity of NOx produced. The analysis of the total amounts of NOx and identification of blast areas those fumes originate from will help to better understand key factors that contribute to their occurrence as well as to quantify the severity of such events. By quantifying the magnitude and concentration of fumes generated by non-ideal detonations, the blasting technique can be optimized to minimize unwanted environmental effects and improve public perception of blasting as a necessary component of societal progress

Jan 1, 2024

By R. Ranjan

Stanstead granite has been investigated with respect to its dynamic compressive strength and its strain-rate dependency. A standard Split-Hopkinson Pressure Bar (SHPB) apparatus has been employed to generate strain rates of up to ~500/s through high-velocity impact. The diameters of the test samples were 19 mm, and tested under impact velocities up to ~20m/s. It is found that even within this limited range of strain rates, the dynamic compressive strength for the granite showed nearly a 100% increase in value compared to those obtained under static loading conditions (e.g. compressive strength of 394 MPa at a strain-rate of 600/s, compared to 215 MPa obtained under static loading). The details of the test are described in terms of incident, reflected and transmitted stress pulses, along with means to achieve stress equilibrium in the test samples under dynamic loading conditions. The advantage and drawback of the use of ‘pulse shaping’ techniques to achieve dynamic stress equilibrium are also detailed.

Jan 1, 2010

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020