Search Documents

By Gandhi

Piled raft foundation under uniformly distributed vertical loads has been analyzed using Finite Element Method. The soil is considered to be linear elastic, isotropic, homogeneous. The raft,pile and the soil have been idealized with eight noded brick elements. Parametric study have been carried out varying pile length, soil modulus, raft thickness, and pile spacing. Design charts have been produced to achieve 50% load sharing between pile and raft for optimum design. Data available in literature is compared with the design chart results and found satisfactory.

Jan 1, 1996

By P. Bermingham

A new approach to load testing of high capacity piles is presented. The method is mobile, inexpensive, repeatable and non-destructive allowing for multiple pile testing at a single site. A reaction mass is placed over a pressure chamber situated atop the pile to be tested. The test method is significant in that it can produce linearly increasing forces of high magnitude (over 5.0 MN) with durations of up to 80 milliseconds. This represents pulse durations an order of magnitude longer than achieved using a drop hammer. The accelerations the pile undergoes are less than one g, (conventional dynamic methods = 50 to 100 g). These effects combine to produce pile behaviour no longer dominated by the action of stress wave, instead the pile is under high levels of stress through its length during the force input. This is representative of the situation when static loads are applied, thus the method may be considered quasi-static. Further advances introduced with this method are that pile deflection and transmitted force are measured directly by means of a laser beam and load cell. This allows accurate correlation of event load displacement histories without the error associated with zero shift (acceleration integration) or non-homogeneous materials (strain measurement). The load displacement histories emulate those obtained for static load testing.

Jan 1, 1989

By Peng Jiahong

With ultrasonics application during checking the large diameter cast-in-situ pile body, it is usualy applied the statistical method of probability and PSD. This paper presents a converse probabilistic-analytical method which can identify important anomalies, both strong and weak, during interfered situation. So the inhomogeneity in concrete pile may be ellectively distinguished. In order to ensure the capacity of bed rock support layer under large diameter pile, a test-in-situ is conducted to determine the compresive strength and shear force inserting rock of the support layer, so the compresive strength and modulus value of elasticity of bed rock tested will closely tally with the actual situation.

Jan 1, 1991

By A. J. Partos

The figures and tables referred to herein are presented in the Proceedings; Volume I, Pages 309 through 316. The 61-story One Liberty Place, at 315 m., is the tallest building 1n Philadelphia and was in 1987 the ninth tallest building in the world. One Liberty Place is supported on drilled piers socketed in heterogeneous metamorphic rock. Design load distribution was 40% on the base and 60% by shaft resistance. Drilled Pier G-10 supporting a T13-A type outrigger column was instrumented. There 1s no uplift load on the exterior outrigger columns. This column supports a 53,850 kN compressive load which includes a 13,440 kN windload. Table 4 presents experimental parameters from straight line interpolation of Mohr failure envelopes for the Wissahickon schist. Lowest values of cohesion (12,200 kN/m2) and angle of internal friction (19°) are at a 50° - 59° angle of foliation. Figure 3 presents a typical pier supported by shaft resistance 1n decomposed (D) and coreable (C) rock and by end bearing (B).

Jan 1, 1991

By Z. Y. Ding

This paper emphasize two points in piled wharf design which are important than structure calculation. First, during design of piled wharf on soft stratum, the bank slope stability is the first important item. Second, the live load, the backfill and the original ground's settlement will influence the wharf structure causes cracks. Two practical examples were illustrated.

Jan 1, 1991

By K. Viking

This article deals with some of the civil engineering related problems to be encountered when offshore wind energy projects transform from prototype offshore wind energy converter farms, developed and installed during the 1990's, to commercial farms that's currently planned to be built. The offshore wind energy converter (OWEC) installations encounter a wide range of problems, only partial of these are geotechnical. In Europe both onshore and offshore wind farms have, from a historical point of view, usually been founded by using the monopole technique, installed with traditional impact hammers, or by using gravitational foundations. However, the rapid development of bigger turbines and larger wind farms, together with increasing considerations of fatigue aspects, has lead to financial benefits of developing and exploring other foundation techniques. This paper reviews some Scandinavian experiences regarding critical components of the design phase in relation to connecting the superstructure to the ground, and some of the main considerations of how the loads applied to the structure are transferred to the surrounding soil. Keywords: Offshore Wind Turbines, Wind Farms, Foundation, Pile, Gravity Structures

Jan 1, 2005

By Joanna Bzówka

Nowadays, there are some new requirements for the supermarket floors. The floors are loaded by high point- and moving-loads. In spite of this fact, it is necessary to ensure the stiffness of the floor and the stiffness of its support. When pile foundations are designed in the case of weak soil, the piles are recommended under the foundations of the supermarket and also under the floor layers. The example of foundation of a typical supermarket located on long­standing municipal dumping ground is presented. Indirect foundation - CFA piles, 0.5 m in diameter and 4.5 to 20.0 m long, was de­signed. Fifteen trial loading tests were carried out.

Jan 1, 2006

By Wu Jie Mei, Li Yao Liang, Franz-Werner Gerressen, Arthur Bi

Diaphragm walls (D-walls) are known as underground structural elements commonly used for retention systems and permanent foundation elements. In addition, they are also quite often used as deep groundwater barriers, called Cut-Off-Walls (COW). Shanghai ranks third among the most densely populated metropolises in the world. In 1990, only eight million people lived there. Today, Shanghai has about25 million inhabitants. The increasing demand to accommodate the infrastructure of growing megacities like Shanghai pushes the required depth for subway, sewage and foundation projects to the limit. Future projects will demand excavation depths of more than 100 m (328 ft) on a regular basis. Already carried out reference projects will be described and a general outlook for upcoming projects will be given. The paper also explains the installation process in general focusing on the use of trench cutter technology. INTRODUCTION D- walls are known as underground structural elements, commonly used as retention systems for excavation pits and shafts as well as permanent foundation walls or elements. It is anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions and with increasing depth. The trench cutter is the most important tool for performing this work. The hydraulic grab, a well-known and valuable excavation tool for d-walls reaches its limits in terms of depth and when cutting rock. Therefore the trench cutter technology will be in the focus of this paper. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around the horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter wheels is continuously broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the suction box of the pump? A centrifugal pump located right above the cutter wheels conveys the slurry via a hose system up to a desanding plant. There the slurry loaded with soil and rock particles is cleaned and returned into the trench.

Jan 1, 2018

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By M. D. Khattar

The paper describes the salient construction features of the Pile foundation work for the Railway viaducts in Algeria. Six viaducts were constructed for execution of the Railway line between Aintemouchent and Benisaf in Algeria. The work was executed by the Indian Railway Construction Company Limited of India (IRCON) for the Algerian National Railways (S.N.T.F.). These six viaducts had multiple spans of 36M resting on hollow piers of heights upto 69M. Most of the piers were founded on piles of 1 and 1.2M dia bored piles going upto 22M deep through cal­careous rocks and were designed for Railway loading in seismically active area. The work involved 356 piles & constituted a very important aspect of the whole work. The concrete in the piles was made with sulphate resistant cement and the integrity of the concrete was tested with Sonic method so as to ensure the quality. The piles were driven with the help of a hydraulic oscillator and the concrete was laid with a tremie pipe. Problems as encountered during execution have been explained.

Jan 1, 1989

By M. Cornelius

Drilled shaft construction through caving soils has historically been an uncertain, risky and costly operation. Uncertain, because the zone of caving may or may not be known, risky because the loss of a shaft is disastrous, and costly because the Contractor, who faces these risks, must include large sums of money in his bid for shaft wall stabilization techniques. This case study will discuss the stabilization techniques that are typically used within the United States, and then present new technologies, born in Europe, that are being utilized in the States by Malcolm Drilling Company today.

Jan 1, 1999

By Steven R. Musselman

The bending strength and flexural stiffness of a micropile at its threaded connection is less than its intact strength and may fail due to thread slippage or by fracture through the pin (reduced cross-sectional area of male threads in the threaded zone of the casing). The mode of failure depends on the reduction in cross-section necessary for machining the threads, and details of the threaded connection such as the length of threaded connection, size and shape of threads, and the thread density (threads per inch). Based on data from bending tests conducted on 9-5/8 inch diameter micropile casing, a method has been developed to predict the ultimate moment capacity and initial bending stiffness of round threaded micropile connections. Two modes of failure were observed from four-point bending tests conducted at the University of Illinois on 9-5/8 inch casing with round threads. Threaded micropile casing connections with an effective thread length of 1.35 inches typically failed by slippage at the threads (jump out), while connections using an effective thread length of 1.89 inches failed by fracture of the pin. These two failure modes were described by W.O. Clinedinst in his report to the American Petroleum Institute on tension tests of threaded pipe casing. Clinedinst developed an empirical formula to determine the tensile strength of threaded connections. A method to predict moment capacity for threaded micropile connections by modeling the micropile cross-section and applying Clinedinst?s equation to determine the max tensile stress along the threaded connection while satisfying force equilibrium is proposed. The predicted moment capacity for threaded connections using this approach is within ten percent of measured for both modes of failure observed from the bending tests.

Jan 1, 2007

By J. Pei

The studies of dynamic measurements using stress wave theory has commenced in China. This paper introduces some practical experiences using "CASE method" in Shanghai showing applications of dynamic measurement to determine ultimate bearing capacity of pile, the change of capacity due to set up, determining the optimum bearing layer during pile driving, the efficiency of hammer system and integrity of pile and discussions of method concered.

Jan 1, 2010

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By A. Mazzucato

This paper presents the experimental results of driving and load tests on an instrumented pile driven into a test pit filled with fine homogeneous sand.

Jan 1, 2010

By Stefano Trevisani

Abstract The FIEC Sustainability Vision states that “risks should be identified and allocated in a fair manner across the project team from the early stages of the design phase. A partnering approach, where objectives and timescales are agreed in advance together with all relevant partners in the value chain, offers a useful solution to improve on site efficiency and reduce disputes”. An alliance or collaborative form of contract involving all parties is the best way to ensure fair contract conditions and proper risk allocation in construction projects. Collaborative contracts are particularly useful where there is uncertainty or undefined information or in the event of technical difficulties and other risks difficult to allocate among the parties involved in the project. Owners sometimes require even special output in terms of innovative technical solutions or special performance. In addition, this particular form of cooperation has been construed and developed with the intention of avoiding and mitigating another great risk associated with the construction industry (especially in complex projects): disputes and conflicts, which are often a major cause of delays, increased costs, loss of reputation and opportunities. In contrast, Alliances are a way to increase and strengthen business relationships, technical and economic innovation and effectiveness, in a worldwide global context where the waste of resources must be avoided in order to guarantee future recovery and growth. Of course, the total cost of a project is usually a key factor and the main driver for the Owner and the Contractors in deciding the type of relationship between them as well as the subsequent relationship with subcontractors and lower-tiers. This paper and presentation, will explain the main features and the principle benefits that the use of collaborative contracts can bring to all parties involved in the construction project, including the sustainable financial return that might be achieved if costly and time consuming disputes can be avoided.

Jan 1, 2014

By William M. Camp

An extensive design phase testing program in which 10 piles and 2 drilled shafts were instrumented and statically load tested to failure, was undertaken to establish relevant foundation design parameters for two bridges in Charleston, South Carolina, USA. The bearing strata at both test sites was a calcareous, overconsolidated, firm to very stiff, slightly sandy, clayey silt (locally known as Cooper Marl). Confirmation dynamic and static loading tests on production piles indicated only 50 to 60% of anticipated pile capacities; including consideration of time effects. Supplemental subsurface explorations did not reveal any significant variations in marl properties. Ultimately, 22 static and 75 dynamic tests were performed on production piles for a 2 mile section of the project. Pore water pressures in the marl were also monitored during and after pile driving. A study of unit skin friction in the marl as a function of time revealed two distinct trends: piles driven in areas with a sand overlaying the marl gained more capacity significantly faster than those driven through a clay or silt. Although the insitu marl properties are apparently similar across the site, the material immediately above the marl evidently has a large effect on pile capacity. This effect of overburden on pile capacity was verified by testing piles over a period of two years.

Jan 1, 1993

By Larry Rayburn

Design of cost effective engineered solutions to complex problems requires the team efforts of the owner, the designer and the specialty construction contractor. The basic ingredients of success required to remain competitive and still produce a quality product are creative design based on experience and sound engineering principles, plus practical aspects of constructibility. The three case histories describe creative design/construct approaches that benefited all parties. 1. Introduction The increasing demand placed on specialty contractors to provide cost effective buildable solutions to complex construction problems compels us in the industry to be highly innovative. The practice of geotechnical engineering is considered more of an "art" than perhaps the other disciplines within civil engineering largely because of the basic nature and variability of soil and rock. The geotechnical design engineer must have the knowledge of the components of his design and know the limitations of his equipment and labor force. Thus, for the design/build specialty contractor the potential for creation of unusual solutions to difficult problems is quite high.

Jan 1, 1991

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By Jesse R. Jacobson

A large casino complex in Cherokee, North Carolina recently underwent a $633 million expansion that involved substantial foundation challenges. The site is located in a valley on the southern edge of the Great Smoky Mountains National Park, where subsurface conditions typically consist of varying thicknesses of fill overlying alluvium, residuum, partially weathered rock and rock. The fill and alluvium contain cobbles and boulders as large as several feet in diameter. The residuum and partially weathered rock are very thick in some areas, and the depth at which consistently high quality rock is encountered is highly variable. To reduce the foundation costs for the expansion, continuous flight auger (CFA) piles were proposed in lieu of micropiles. CFA piles are not generally used in this geologic environment and concerns regarding their selection included: (1) an uncertainty that CFA piles could be successfully constructed given the difficult conditions and (2) a lack of regional data regarding unit resistance values and load transfer characteristics. To address these concerns, a design-phase test program was undertaken to evaluate pile constructability, develop an understanding of the load transfer behavior, and establish the required pile lengths. The program included soil test borings, shear wave velocity measurements, timed auger probes, instrumented pile load tests and observation of exhumed piles. It was demonstrated that CFA piles could be advanced through the fill, cobble/boulder-laden alluvium, residuum and into the partially weathered rock, albeit with some limitations. Under axial loading, the pile response was very stiff and relatively high unit resistance values were measured. Pile instrumentation allowed for the evaluation and use of design pile lengths shorter than that tested, and the overall reduction in pile lengths yielded a 40 percent reduction in foundation cost. In general, CFA piles were determined to be a suitable, economical foundation alternative.

Jan 1, 2011