Search Documents

By Donald Lindell

Safety Share ?Dad receives fryer for Christmas 2009 and makes delicious sweet potato fries ?When the oil fryer was pushed back on the stove for cooling, the back edge comes into contact with the stove top controls, unknowingly activating the cooking element, family leaves kitchen. ?Faint smell of smoke from the melting plastic alerted the family; teenager arrives first and pulls the fryer forward causing oil to spill onto hot stove and burst into flames that reach the microwave ?Teen runs for sink to grab pan of water but is stopped by Dad ?Dad opens refrigerator, grabs baking soda and pours it on fire, extinguishing flames Lessons 1.DO NOT USE WATER ON GREASE FIRE 2.Where is the baking soda in your kitchen?

May 1, 2010

By L. Xia, B. Hart, J. Nigim, Z. Chen

"Grinding ore is an important step in the flotation process. Not only does grinding reduce particle size and liberate minerals, it also creates conditions for reactions to occur on particle surfaces that can aide or inhibit flotation. There have been numerous studies examining various grinding regiments and the effect on flotation pulp chemistry, including autogenous grinding and using media of variable composition. There have been however, few studies looking at the effect of variability in grinding media size on pulp chemistry and subsequent flotation. This study attempts to link changes in pulp chemistry in response to variations in grinding media size to flotation recovery. It uses probes mounted in the grinding chamber (pH, Eh, DO, and conductivity) to monitor pulp chemistry changes during grinding of a Cu-Zn ore. Surface chemistry analysis by ToF-SIMS was performed on sphalerite from the mill discharge. Activator and depressant species were monitored on the mineral surfaces and their presence was evaluated in the context of variability in pulp chemistry linked to differences in grinding media and its ball size.INTRODUCTIONIt has been widely recognised that not only does grinding reduce particle size and liberate minerals but the grinding environment has a large effect on the flotation of sulphide minerals. This effect is attributed to Eh change, iron hydroxide coating on surfaces, oxygen reduction, precipitation from solution and galvanic coupling (Grano, 2009). As early as 1960, it was reported that after grinding the ores in an iron mill the natural floatability of sphalerite was reduced significantly (Rey and Formanek, 1960). Kocabag and Smith (1985) studied on the industrial circuits showing that the depression of sulphides flotation in a steel mill is possibly due to the coating of iron oxidation products. Peng, Grano, Fornasiero, and Ralston (2003a, 2003b) found that iron contamination from grinding media plays a dominant role in depressing galena and chalcopyrite flotation. Huang, Grano, and Skinner (2006) reported the same observation in the flotation of arsenopyrite."

Jan 1, 2016

By M. Ghiani, P. Carbini, R. Ciccu, C. Del Fà

"This paper is concerned with the problems inherent in the efficient and economical processing of the fine fractions of a coal from the Sulcis basin (Sardinia, Italy) whose characteristics are typical of low-rank coals occurring in the Mediterranean region. Three different techniques, based upon surface properties, are examined. Flotation can be very efficient from both a technical and economic point of view, provided care is taken in the modulation of the flotation pulp. Interesting results have been obtained with oil agglomeration and this method could be economically feasible. Finally, electrical separation has proven a viable technique, although it entails preliminary drying.Besides discussing the problems encountered in the experimental research, some significant results of general validity are also given. They demonstrate that cleaned products can be obtained with fairly interesting recoveries, thus opening the way to advanced research aimed at setting up the most suitable technique for industrial application. IntroductionAs a result of the oil crisis, which caused a major upset in world energy supplies, the last ten years have seen a revolution in the energy policies adopted.In particular, the status of coal, which seemed destined to decline in view of the availability of liquid fuel, has had to be re-examined. The need to meet energy demands under improved reliability conditions and controlled prices through a broader and more flexible diversification of sources of supply has evoked, especially in highly industrialized countries, a renewed interest in coal. The result has been a consistent increase in demand and production as well as investments in new mines and the reinforcement of the infrastructure.This turn of events has also lead to a re-evaluation of young low-rank coals, hitherto considered uneconomical and thus neglected, because of their low heat value. In fact these coals, which have a high ash content, may also be relatively highly contaminated with sulphur. The above drawbacks, which still today preclude the widespread use of these coals, are bound to create even greater problems in the future as increasingly restrictive environmental control imposes, without exception, recourse to cleaner fuels."

Jan 1, 1986

By R. Sage, N. Rillette, M. D. Everell, G. Herget

"CANMET has been operating as a Government Technology Centre for two years. Many of CANMET's programs involve long-term research and require special expertise, often available at Canadian universities. CANMET's involvement with universities ranges from research grants and contracts to exchanges of scientists and joint use of research facililies. Examples of CANMET - university cooperation in mining are presented. IntroductionIn the last two years or so CANMET has undergone a significant metamorphosis, resulting in greater emphasis on applied research to enhance Canada's industrial capability. CANMET's new mandate is reflected in the types of projects undertaken and their categorization, (Fig . I). Emphasis is being placed on two project categories: strategic R&D, to enable CANMET to serve the changing technological needs of the industry; and incrernental R&D, to serve the more immediate industry needs through modifications to existing technologies and knowledge. The balance of CANMET's e ffor t is devoted to providing Mandated and Specialized Services, and to Exploratory Research.CANMET interaction with universities can involve one of several available vehicles : contracts, research grants, exchanges of scientists , student employment and nomination of professors on CANMET's advisory council. Instances of key university technical support to CANMET mining projects are highlighted."

Jan 1, 1990

By C. John Sullivan

Is there a relationship among the Sudbury nickel ores, the Cobalt deposits, and the Huronian, Athabascan and North Australian uranium provinces? All are within intracratonic basins, with ore near basal unconformities. There are similarities in the geochemical "fingerprints" pointing to basic igneous rock affiliations. Some show a time relationship to basic igneous activity and to great rift systems. Many basic dykes show radioactivity at their edges. A spatial relationship between the uranium-cobalt-nickel ore at Midwest Lake, Athabasca, and basic igneous rock is reported. These remarks are not meant to imply, necessarily, a direct genetic connection between the basic dykes, etc., and the ore. In some cases, the relationship may be similar to that noted between basic and ultrabasic intrusives and volcanic massive sulphide ore deposits. Crustal thinning in these areas, associated with graben, appears to have favoured volcanic activity, as well as basic intrusives. Probably, the potential of the Huronian should be re thought . Athabascan-type ore may be present . New data on mineralization in Turner Township, Ontario, suggest this. The mineral possibilities of other basins should be reconsidered. It is to be remembered that the Athabascan and Kombolgie basins were neglected for many years. Intracratonic sedimentary-igneous basins contain many of the greatest mineral fields of the world.

Jan 1, 1979

By P. Au, P. Patnaik, H. Saari, D. Y. Seo, S. Bulmer

Ti-48Al-2Cr-2Nb-xW (where x = 0, 0.5, and 1 at. %) powders were consolidated by hot isostatic pressing (HIP). The consolidated samples were solution heat treated above the a-transus followed by stepped cooling to room temperature. Selected samples were subsequently aged at 950 °C for up to 72 hours. The post-heat treatment microstructure was examined by optical and electron microscopy. It was found that increasing holding time above the a-transus generated a more homogenous microstructure. Utilizing the stepped cooling sequence, especially with a transition temperature of 1270 °C, massively transformed gamma (Ym) was diminished. Aging caused coarsening of the fully lamellar microstructure in the 0%W and 0.5%W samples while almost no coarsening occurred in the 1 % W sample. Precipitates began to form during aging in samples containing W. The precipitates at the lamellar interfaces are fine and have a needle like shape, while precipitates at the lamellar grain boundaries are coarse and circular in shape. The size and number of the precipitates depend on aging time and the level ofW content.

Jan 1, 2006

By K. C. Corin, M. S. Manono, J. G. Wiese

Depressants play a crucial role in the flotation of PGM bearing ores as they prevent naturally floatable gangue (NFG) from reporting to the concentrate. This action is regarded as critically important because less dilution of the concentrate means lower costs for downstream processes. However, abnormal water conditions (such as high concentrations of ions) in the flotation system can modify the selectivity of these depressants. It is well known that the existence of selected electrolytes in water can alter the behaviour of some polysaccharide depressants by enhancing their adsorption onto gangue minerals and thereby prevent naturally floatable gangue from moving into the froth phase. Concurrently these same electrolytes may enhance frothability, owing to their stabilising effect on the bubbles within the system. Plant water at various ionic strengths was investigated against depressant type and dosage in order to understand electrolyte-depressant interactive effects during the flotation of a Merensky ore, using entrainment, rate of NFG recovery, and total gangue recovery as proxies. The study showed that the rate of NFG recovery per unit mass of water decreased with increasing ionic strength at all dosages, however the total amount of gangue reporting to the concentrate increased with increasing ionic strength at all depressant dosages. Thus, this paper attempts to consider the effects of both ionic strength and depressant dosage as individual factors within flotation. It further looks to investigate whether any interactive effects exists between these two factors when considered simultaneously.

Jan 1, 2016

By Abani R. Samal

The Fe assay values from the diamond drill-holes within a magnetite deposit of magmatic origin are utilized in this study. Only assay data from the unoxidized magnetite mineralization was utilized. The data from the overlying hematite mineralization zone was not used. A threedimensional block model estimated using ordinary kriging (OK) is used for analysis purposes. To estimate the non-linear standard deviations (s) and the confidence intervals (CI) of block estimates a discrete Gaussian variogram model is used in this project. The change-of support coefficient (rv) and the block-support correction are used in the ?block-anamorphosis?. A new calculated value of rv is 0.7283, implies that its influence in the block-anamorphosis is not significant. The CIs are calculated from the block-gaussian variables; then back transformed to the raw values. At 95% probability, the CI for the kriged block estimates of Fe values are calculated using Gaussian kriged estimates of the Fe and the corresponding standard deviations (Gaussian). The results indicate that the block estimates with a high influence from relatively small amount of samples can be identified as high-risk estimates.

Oct 1, 2009

By Patty Simpson, Sarah Benson

In an effort to improve consistency across the nuclear industry, over the past 10 years the Canadian Standards Association has developed a series of standards related to environmental management at Class 1 nuclear facilities and uranium mines and mills. Canadian uranium mines have been required by the Canadian Nuclear Safety Commission to align their existing monitoring programs with these standards. Orano’s McClean Lake Operation’s monitoring program, which was originally presented in the Environmental Impact Statement in 1991, has evolved through regulatory change, new scientific understanding, additional projects, and experience into a comprehensive set of monitoring requirements for effluent, groundwater, air emissions, and the receiving environment. The exercise of aligning the existing practices with the standards provided an opportunity to review and rationalize the entire program. To document the process the original “Environmental Monitoring Program Design Document” was restructured and developed as both a repository for historical information and monitoring rationalization, and also to be a living document describing on-going studies and supplementary work that are outside of the regular environmental monitoring program and may justify future changes to the program.

Jan 1, 2020

By Claude Gosselin

En 1995, la Compagnie minière Québec Cartier a mis de l'avant un projet de recherche sur la modélisation de l'écoulement des gaz pour ses fours de frittage à l'usine de bouletage de Port-Cartier. Cette démarche s'inscrivait dans un large processus de collaboration avec l'Université Laval et le Consortium de Recherche Minérale (COREM). L'usine de bouletage possède deux fours de frittage d'une capacité moyenne de 600 tonnes/heure pour chacun des fours. Les fours de frittage sont des systèmes complexes d'échange de chaleur qui fonctionnent à contre-courant (le débit de boulettes versus les débits de gaz). Pour rencontrer les spécifications reliées aux propriétés mécaniques des boulettes, le processus de fabrication requiert des mesures et un contrôle des systèmes très précis. L'information fournie par plus de 70 capteurs (pression, température, puissance, vitesse, hauteur de lit, position de volet....) est utilisée pour manipuler une vitesse de grille, cinq ventilateurs et neuf zones de brûleurs. Malheureusement, les variables qui influencent fortement les mécanismes de frittage, c'est-à-dire les débits de gaz dans les différentes zones du four ainsi que la masse de boulettes qui circulent ne sont pas mesurées. Une méthode est donc proposée pour une estimation en ligne de ces variables. La méthode est basée sur un arrangement de 65 équations reliant pressions, températures et débits de gaz dans les conduites, les ventilateurs, les sections du lit et les fuites (Gosselin, 1998). Pour des raisons de simplification de cet article, seul un sous-système du four sera présenté. Les techniques de réconciliation des données reliées à la conservation de la matière et de l'énergie montrent que la mesure en ligne du débit de boulettes mène à l'estimation des débits de gaz et apporte des avantages intéressants pour le contrôle des variables stratégiques des fours.

May 1, 2001

By Z. Pilecki

This work concerns the identification of weak zones in the structure of a rock mass endangered by outburst of gases and rocks in the Rudna copper ore mine at greater depths (approximately 1200 m). A special methodology has been undertaken for the recognition of that threat in the wake of an outburst in the mine in 2009. No similar phenomena have been previously recorded in KGHM Polska Miedz copper ore mines. The research described in this paper was carried out in the new part of the deposit prepared for mining. Geophysical methods were used: seismic tomography and borehole ground penetrating radar (BGPR), along with particular identifications using geological engineering methods. In the researched area, Permian layers of sandstone and shale clay (Weissliegendes formation) and of Zechstein dolomite (top of Rotliegend formation) and anhydrite occur in the copper ore deposit. The rock layers are characterized by variable thickness and intensity of mineralization, varying internal structure, and local fracturing containing different gases and water. It is assumed that accumulation of gases occurs in the tectonically fractured dolomite. The study was focused on the recognition of the structure and properties of the dolomite layer lying directly within the roof of excavations. The first tests were performed with seismic tomography for the recognition of anomalous changes in the elastic properties of the rock mass. The results of these studies were used to design a control borehole for a detailed geological engineering assessment and BGPR surveys with 100MHz antennas. Seismic tomography enabled the identification of changes in Pwave and S-wave velocity, the Vp/Vs ratio, dynamic Poisson's ratio and dynamic Young's modulus. It was clear that seismic anomalies required verification by other methods. The BGPR survey was performed in a specially designed borehole, passing through the selected seismic anomalies. While the borehole was being drilled, the outflow of gases was identified, with varying amounts of CH4, CO2, and H2S detected, as well as water outflow. The results of BGPR confirmed the location of a reservoir of water and gases, about 30 m in length, found in layer of dolomite. The direct cause of the BGPR anomaly was assumed to be intensive fracturing, a greater content of clay material in the dolomite, and the presence of water in the fractured zone. The BGPR image was correlated with information on lithology, fracturing based on the RQD index and additional information acquired during drilling about water and gases surveys and other symptoms. The achieved results also showed a very strong correlation between the location of the zone containing gases and water and the anomalous S-wave velocity and field of dynamic Poisson?s ratio, and to a lesser extent other seismic parameters. It was found that the other measured seismic anomalies may be of the same nature as those identified in the control borehole and accordingly will require the implementation of detailed identification. The performed tests have also shown the usefulness of geophysical methods to identify geodynamic hazards under the geological and mining conditions of the copper ore deposit in the Rudna mine.

Aug 1, 2013

By Douglas H. Silvey

"The historical transformations in fire -resistant conveyor belt compositions in the past 20 years have been influenced by factors of material cost, changing flame and burn test requirements, material replacements, adhesion and oil resistance considerations, increased responsibility and legal liability. Specifically, this has resulted in a swing from neoprene-cotton belts to S.B.R. blends and synthetic fibre carcasses, and tighter quality control and documentation of test data.Flame dynamics are discussed and the function and performance of the multiple types of flame-resistant additives in the flame front are presented. Specific flame and burn test requirements are described. The belt manufacturers' requirements and criteria in selecting the types of flame-resistant additives are presented.The author will describe the composition of the types of flame-resistant compounds used in a practical production, the belts that are available on today's mark et and future developments in requirements that may further transform the composition of fire-resistant belts.IntroductionThe historical transformations of conveyor belt compositions in the past two decades have been based on factors common to those leading to changes in man y organic compositional products. These factors are material cost, new materials, the customer' s changing requirements, government regulation s and increased manufacturer' s liability.As a basis for understanding the product, I will provide a brief breakdown of the conveyor belt composite. Figure 1 represents a cross section of a typical belt. A skim rubber coats each fabric ply of the belt carcass and is of a different rubber composition than the outside layer of rubber which forms the cover. This outside cover layer is designed to protect the belt from environmental factors such as heat, oil and abrasion, and other factors involved in the service condition s under which the belt will operate. In the case of fire-retardant belt s, both the skim coat encapsulating the fabric plies and the outer cover must contain sufficient fire retardancy to overcome the contribution to burning of the decomosition products of the fabric."

Jan 1, 1982

By M. Loan

The Zinifex's Hobart Smelter uses the paragoethite process to remove dissolved Fe(III) from concentrated zinc leach liquors. This produces a residue consisting primarily of 6-line ferrihydrite (a hydrated Fe(III) oxyhydroxide), several insoluble components derived from the calcined zinc concentrate neutralization agent and other precipitated phases, such as jarosite and silica. The precipitation of 6-line ferrihydrite in the paragoethite process was studied using a laboratory-scale continuous crystallizer, and the conditions were selected to limit high levels of dissolved silica and jarosite. This approach allowed the reactor pH and the rate of precipitation to be correlated with residue solid-liquid separation, particle size, morphology, residual zinc and sulfate concentrations, and phase formation (e.g., goethite, jarosite, schwertmannite, and 2- and 6-line ferrihydrite). These studies delineated the mechanism of 6-line ferrihydrite precipitation in the kinetically controlled paragoethite process, and its inter-relationship with goethite and jarosite precipitation under conditions where 6-line ferrihydrite is favoured. Unexpectedly, the generation of a more crystalline goethite precipitate with larger "primary" particle size did not produce a residue of improved properties, as bulk aggregates dictate the physical properties of the residue and not the crystallinity. Furthermore, it is difficult to precipitate 2-line ferrihydrite or schwertmannite under existing paragoethite process conditions.

Jan 1, 2006

By S. I. Saif

The Key Anacon deposit lies about 6 miles northeast of the Brunswick NO.6 mine of Brunswick Mining and Smelting Corporation. Geological mapping, especially in the well-exposed Nepisiguit River section, geophysical data, and information from extensive underground and some surface drilling show that the rocks at Key Anacon are similar in many aspects of stratigraphy and structure to those of the Brunswick Mine area. They include narrow beds of fine acid volcanic material interpreted to be metatuff and volcanogenic metasediments. The massive sulphide ore body at Key Anacon lies immediately above these acidic rocks, in association with other chloritic, sideritic or magnetic iron-rich metasediments. The iron formation, which is similar to that associated with other orebodies in the district, is overlain by massive andesitic material. Four phases of structural deformation have been recognized in the Key Anacon area; they are similar in intensity and style to those of the Brunswick No. 6 mine area. The orebody lies in a zone of complex isoclinal folding along the flank of a major F2 fold (Key Anacon Syncline) and in general appears to be stratiform. The ore occurs in probable F2 parasitic folds, and this suggests a complicated structural geometry superimposed on the original beds. The general similarity of the mineralization at Key Anacon, together with its occurrence with other iron-rich metasediments between a footwall of acid volcanic material and overlying andesitic rocks, is suggestive of stratigraphic time-equivalence with the Brunswick zone . If so, the metavolcanics at Key Anacon might have been derived either from a center within the main volcanic pile to the west or from a smaller local center active at the same time. Alternatively, the Key Anacon ore could have been formed during a much older volcanic cycle. The solution to this aspect of the problem is the subject of a continuing study.

Jan 1, 1978

By S. Kelebek, Gerhard W. Heinrich, Peter F. Wells

"The review and optimization of process stages is an integral part of the program to improve the metallurgical performance of the Strathcona Mill. Improved primary grind size distributions, streamlining of rougher-scavenger circuits and increased platinum recoveries were the target of plant and laboratory scale tests. The results can be summarized as follows:• Decreasing the primary grinding cyclone vortex finder diameter for nickel/copper ore gave significant increases in overall copper recovery and improved rougher flotation selectivity.• The scavenger flotation stage in the circuit treating copper ore was found to contribute little to this circuit's copper recoveries -yet to be essential for acceptable recoveries of nickel, platinum and gold. The elimination of this stage by re-routing the tailings from the copper ore rougher into the nickel/copper ore rougher feed has lead to lower gangue recoveries to the nickel concentrate and to improved copper-nickel separation, while reducing equipment operating costs.• Surface aging effects such as oxidation are known to decrease flotation recoveries of platinum minerals such as sperrylite. The conditioning of an intermediate non-magnetic process stream with copper sulphate prior to thickening increased the platinum recoveries in the subsequent flotation stage by approximately 10%."

Jan 1, 1996

By D. M. Watson

Mineral discoveries and subsequent extraction have led to the establishment of many small communities, some major towns and a few cities . In Canada, such developments have essentially occurred without benefit of long-range regional or local planning. In the past, this was not a cause for concern. Now, however, rising expectations and reorientation of social values have placed increasing responsibility on government and industry to ensure the long-term viability of communities and regions. Such responsibility means large investments by government in infrastructure and by industry in extractive and processing plants. Uncertainty in the interpretation of ore reserve estimates becomes a critical factor. The traditional methods of reporting reserves - "proven", "probable" , "possible" - may be useful in individual mine production planning, but they are inadequate for planning industrial and public infrastructure, The need for a better information base is critical, with clear and precise definitions of what is being reported, but we are a long way from achieving it. The challenge is therefore to develop a closer professional relationship between government and industry and to tie mineral development to long-range regional strategies.

Jan 1, 1977

By T. Rahimzadeh, C. W. Trueman, S. Farzaneh, S. V. Hoa, I. Abdalla

This paper presents the shielding effectiveness (SE) of woven continuous carbon/epoxy composite materials. The theoretical and physical concepts behind the experimental results are demonstrated in details. The influence of frequency, the overlapping angle between overlapped layers and the number of overlapped layers upon the EMI shielding of composite sheets are discussed. In this work, in particular, the epoxy layers are considered as dielectric apertures of the conducting carbon fiber slab for the interpretation of the experimental results. The experimental results, using ASTM standard D4935-89, indicate that the SE can reach values greater than 90 dB above 500 MHz.

Jan 1, 2006

By J. A. Finch, R. R. Cunningham

The amount of foam volume generated in relation to the gas flowrate has long been used to define the foaminess of a solution and to characterize surfactants. The vessel geometry and gas flowrate range can affect the foam volume results. A fixed area column was tested alongside a variable area conical vessel with two surfactants. It was found that the fixed area vessel will cause foam volume to expand or contract which masks the effect of the surfactant. The conical vessel showed two regimes of foam volume production dependant on gas flowrate. The low gas flowrate regime revealed the physiochemical nature of the surfactant while a high gas flowrate revealed kinematic properties. Foaming properties of a surfactant is best determined with a variable area vessel at low gas flowrate.

Jan 1, 2009

By R. B. Smith, D. C. Brady

"A review of the major renovation of the fifty-year old C-I headframe facilities at NERCQ's Con Mine, Yellowknife, N. W.T. is provided. The project was complete with only two 3-day shutdowns of the facility .Work consisted of four major phases: structural reinforcement of the adjoining mill building prior to dismantling; relocation of virtually all mine and mill utilities which transited the headframe collar en route from the adjacent powerhouse; dismantling of the entire headframe facility and portion of the mill building, including the removal of asbestos siding; and erection of a new headframe, idler rower, collarhouse and mill wall.This paper describes the work and methods used by NERCQ, J.S. Redpath Mining Consultants Limited, Acres International Limited, and others to bring the project to a successful completion. The history of the project is discussed from the planning phase through construction, including; design, procurement, and construction scheduling. The paper discusses the unique elements of the project, the problems encountered, and the methods used to achieve success.IntroductionThe Con Mine is a 800 tpd gold operation located in Yellowknife, Northwest Territories. Originally owned and operated by Cominco Limited , the Con Mine was sold in December 1986 to NERCO Minerals Company, and officially renamed NERCO Con Mine, Ltd. The Con Mine has been in operation for over 50 years. The first gold brick ever produced in the Northwest Territories was poured at the Con Mine in 1938. The original C-1 shaft was sunk in 1937 to a depth of 235 ft. In 1941 the shaft was deepened to a depth of 950 ft, and the original timber head frame was replaced with a steel structure. Following the discovery of the Campbell Shear in 1946, the C-l shaft was again deepened to its present depth of 2443 ft. Over the years, mine production gradually moved deeper and further from the C-l shaft."

Jan 1, 1991

By W. G. Jewitt

Introduction The use of the aeroplane in prospecting is already familiar to everyone connected with the mining industry. Apart from transportation companies, three organizations, the N. A. M. E., the Dominion Explorers, and the Exploration Department of the Consolidated Mining and Smelting Company, have made the aeroplane an everyday feature in every mining district in Canada. Its use has been demonstrated successfully in the mountains of British Columbia, but perhaps its greatest field lies in the Canadian Shield, where the numerous lakes and rivers afford an almost continuous series of landing places for aeroplanes, on floats in the summer and on skis in the winter. To the man who has travelled by canoe, toiling over fly-infested portages or held for days at a time, wind-bound, on the big lakes, the ease, speed, and cheapness of aeroplane travel have marked the beginning of a new era, in which ground previously covered with difficulty in a month or more is travelled with ease in a few hours. Development of an air service in the Consolidated Mining and Smelting Company has proceeded on different lines from those of other organizations, and this paper is concerned with that development.

Jan 1, 1931