Search Documents

By K. Thuro, B. Sellmeier, M. Krautblatter

"Recent rockfall events, like the Tramin rockfall at January 21st, 2014, underline the significance of a comprehensive hazard assessment. A common way of estimating the hazard along infrastructure is the performance of run-out modelling using 3D rockfall codes like Rockyfor3D or RAMMS::Rockfall (Dorren, 2010, Bartelt et al., 2013). The potential block volumes are often roughly estimated from talus material and an overview of the source area, where the magnitude assessment is usually physically and intellectually demanding. Nevertheless especially for increased magnitudes, the volume estimation is crucial in terms of hazard analysis. Mid-Magnitude-Events exceed the load capacity of the most mitigation measures and their date of failure is hard to predict. Here we define the term Mid-Magnitude-Events as block volumes between boulder falls (10-100 m³) and block falls (100-10,000 m³) (Whalley, 1984).The current contribution provides an approach of integral process analysis for a 200 m3 carbonate block above the federal road B 305 near the city of Salzburg in the Bavarian Alps, Germany. We performed detailed analysis of the critical carbonate block exposed to planar failure. The block volume and the dimensions of the failure surface were mapped in detail, due to the unique occasion of an accessible failure surface. The discontinuity persistence was recorded to assess a minimal degree of fragmentation for a potential failure scenario. A maximum degree of fragmentation was estimated due to recording of block dimensions at the talus slope resulting from frequent rockfalls.We performed parameter studies in terms of run-out modelling using the code RAMMS::Rockfall (Bartelt et al., 2013), taking the recorded data for block fragmentation into account. In our contribution, we aim to demonstrate a comprehensive approach for hazard assessment of mid magnitude rockfalls, taking detachment processes, fragmentation and run-out analysis into account."

Jan 1, 2015

By F. Filzwieser, K. Gamweger

The process of gas purging in molten aluminium has been an industrial practice in Europe for many years. The advantages are a reduction in the hydrogen content and impurities in the melt, as well as a homogenisation of the temperature and chemical analysis in the molten metal. Formerly used lances or impellers are being replaced by porous plugs which are installed at the bottom of the furnace. This special product of RHI Refractories has proven its efficiency in primary melting as well as in die cast, sheet and extrusion plants.

Jan 1, 2004

The steam-filtration process for dewatering solids involves the application of slightly superheated steam to a filter cake during filtration. The mechanism by which the technique promotes water removal has been deduced from bench-scale experiments on coal and on granular iron ore concentrates. The mechanism, along with some of the applications and limitations of the process, is presented. Introduction I N the steam-filtration process, slightly super-heated steam is applied to the filter cake during filtration to remove more water than can be extracted by conventional filtration. Although this process was developed by Burton for coal filtration (1), it should have far wider applicability; certainly, it could be used to treat any mineral product, because only low-temperature steam is needed and most conventional filtration equipment can be easily adapted to it. As few restrictions apply to this process, however, it is important that its more obvious advantages and disadvantages be appreciated and, especially, that the criteria on which economic evaluations can be based are understood.

Jan 1, 1965

By W. T. Gotheridge

The principal sources of coal-dust underground are, of course, coal, and the working of coal. Coal-dust is most dangerous when it is in the finest state of division. This class of dust is found mostly on the roads, being blown or shaken off the loaded trams in transit, or carried in suspension by air currents. The air current passing from the working faces may also carry dust in suspension into the return airway, and the air current from the surface may carry dust from the shakerscreens into the intake airways. The mosl dangerous dust we have to contend with is, (a) that which is most finely divided, and (b) that which contains the most volatile matter, including the inflammable occluded gases, and also oxygen absorbed from the air. According to experiments, coal-dust in a fine and dry state would intensify an explosion, in air free from fire-damp carrying in excess of 3 ozs. of fine dust or 6 ozs. of coarse dust per cubic yard. The volatile matter in the dust must be between 12 and 31 per cent. in the ash-free coal, the latter percentage giving the highest flame velocity. It is vary difficult to propagate flame where coal-dust contains a large percentage of stone-dust, (say 50 per cent.). Shale-dust or other incombustible dust containing no volatile hydro-carbons or carbonaceous matter will prevent the extension of an explosion if mixed with coal-dust in proportion of say 70 per cent., and if the dust is finely divided and dry.

Jan 1, 1924

By G. R. Webber, P. J. Whittaker

"A multielement (Au, Cu, Pb, Zn, Ni, c-, Ag, As, Hg, Co, and S) geochemical rock sampling survey was carried out in 1977 in the Munro Township area of Ontario to assess the application of rock geochemistry for gold exploration in the region. Detailed sampling with analysis for gold and arsenic was done in 1986 in the immediate vicinity of the Croesus Mine.Samples of quartz veins and rock formations were taken in regional traverses and in more detail near old showings, prospect pits, and trenches. Quartz, graywacke, carbonate rock, and rhyolite contain the highest concentrations of gold for samples taken away from the old workings. Ultramafic rocks and gabbro have uniformly low gold. Basalt samples have slightly higher geometric means, but individual samples contain high gold concentrations. Multielement highs are mostly in mineralized quartz samples. Gold distribution is independent of other elements in most other rock types. Samples near old showings possess elevated concentrations of gold indicating that prospecting for individual mineral deposits by bedrock sampling is feasible. Concentrations of gold greater than 100 ppb are mostly within 30 m of old workings. Those samples which contain greater than 1000 ppb Au were obtained from quartz veins, basalt, graywacke, and rhyolite.High concentrations of gold were not notably concentrated near the Contact Fault although some anomalous samples came from near and on both sides of the fault. Arsenic concentrations are elevated near the Contact Fault. Detailed sampling near the Croesus Mine suggests that gold was introduced with faulting, alteration and quartz veining. Gold and arsenic have been added to the wallrock in the vicinity of the main veins."

Jan 1, 1989

By Lee Nichols

The Oil Sand Industry in northern Alberta, Canada, disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called Consolidated Tailings or Composite Tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities. Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are long-term stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface. The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process.

May 1, 2004

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016

By A. J. Hyett, N. Hedrick, J. Blackall

The Garford bulb anchor is a modified cable geometry developed and patented by Garford Ply Ltd. of Australia, and which has recently become widely available in Canada. It is produced by deforming the seven wires (including the central kingwire) of a standard cable into a bulb" (Fig. 1). Laboratory cable pull tests indicate that the bond capacity of the 25 mm Garford bulb anchor is comparable to the nutcase cable, in excess of the birdcage cable, and significantly higher than standard 7-wire strand. Its comparative advantage over the latter is most significant for tests at low radial confinement and high water:cement ratio grout, which corresponds to operational conditions of low quality rock (i.e. weak, highly fractured rock masses, foliated hanging walls, failed ground, etc.) and poor installation quality control (perhaps the most common explanation for cable bolt failures). It is under such conditions that cable bolting is often ineffective. The most impressive result is that for a reduction of the effective rock mass modulus by a factor of five, the Garford bulb cable capacity remains virtually unchanged.

Jan 1, 1995

By John Eggert, Paul Benford

"Since 1982, Placer Dome Inc. -Dome Mine has steadily increased mill throughput. Tonnage has increased from a nominal design capacity of 3000 short tons per day, attained in 1985, to 4130 stpd by the end of 1992. Many minor and major circuit adjustments were tried to maximize tonnage.Having utilized most conventional means of increasing tonnage, further increases required a newer approach. This paper discusses the Dome experience in the development and implementation of an expert system.The Comdale/C system was chosen for a controlled trial. The criteria for acceptance were: increased tonnage had to be sufficient to pay for the system; the increase had to be visibly sustainable and the mill operators had to be willing to accept the system.The criteria for purchase were met during the trial and the system was purchased. The system continues to perform well. The tonnage throughput increase has been sustained while operator acceptance remains high.IntroductionPlacer Dome Inc. -Dome Mine is Canada's oldest operating gold mine. The mine was among the first established in the Porcupine camp in what is now Timmins, Ontario. The City of Timmins is located approximately 500 miles or 800 kilometres north of Toronto. Figure 1 shows a map of the province of Ontario and the mine location.In 1912, milling began at a rate of 350 short tons per day. With two minor exceptions, milling has been continuous since this time. The first of these shut downs was in 1918 during the first world war. The war created labour shortages which forced the mine to stop production for more than a year. The second was in 1930 when fire destroyed the mill."

Jan 1, 1994

By M. K. Kim

This study presents a framework for quality inspection of precast concrete components using the 3D laser scanning technique. As precast concrete-based rapid bridge construction is getting standardized, quality assessment of the precast concrete becomes critical for preventing any failures during the construction process. Moreover, as Building Information Modeling (BIM) gains popularity in the construction industry, autonomous and intelligent inspection systems are needed. Current method for quality control of precast concrete components, however, heavily relies on visual inspection and contacttype measurements, which are time and labor demanding. Also, storage and delivery systems of inspection information such as the procedures and results of quality inspection are lacking. To overcome these limitations of the current quality assessment technique for precast concrete, this study aims to develop a BIM-based framework for efficient quality inspection of precast concrete with the use of a 3D laser scanner. First, we formulate practical guidelines including detailed inspection procedure, selection of optimized scanner and scan location, inspection criteria, and data storage and delivery system. Second, to investigate the applicability of 3D laser scanning to precast concrete quality inspection based on the proposed framework, a case study inspecting quality of a lab-scale object assumed as precast concrete component is presented for detecting defects.

Aug 1, 2013

By Y. Nishida, Y. Nara, T. Ishida

Understanding time-dependent deformation and fracturing in rock is essential, because the information of the long-term stability of rock is required for many sub-surface structures excavated in a rock mass. Time-dependent fracture propagation has been invoked as a potential key mechanism responsible for the increase in seismicity preceding earthquake ruptures. In engineering projects and in preventing natural hazards, the study of time-dependent fracturing is necessary. Subcritical crack growth is one of the main causes of time-dependent fracturing in rock. For silicate rocks, subcritical crack growth has been investigated by various researchers. It has been clarified that surrounding environmental conditions (temperature, humidity, and existence of water) have strong influence on subcritical crack growth in silicate rocks. Therefore, the information of subcritical crack growth in silicate rocks has already been enough. On the other hand, information of subcritical crack growth in carbonate rocks is not enough. Especially, the influence of surrounding environment on subcritical crack growth in carbonate rock has not been clarified yet. In this study, we investigate subcritical crack growth in carbonate rock experimentally using a fracture mechanics testing method. Marble obtained in Skopje in Macedonia is used as a carbonate rock sample. The Double Torsion method is used to measure the crack velocity and stress intensity factor. Especially, influence of water on subcritical crack growth in Macedonian marble is investigated. It was shown that the crack velocity in water is much higher than that in air at the same temperature. Based on the results of subcritical crack growth measurements, the long-term strength is evaluated for marble. It was clarified that the long-term strength in water is lower than that in air in marble. It is concluded that water has a remarkable influence on subcritical crack growth in marble. It is also considered that the long-term stability of carbonate rock masses should be ensured in a dry environment.

Jan 1, 2015

By C. Larsen, R. A. Walker, A. Voth, C. Daoust

"The 3000 t/d mill at Hernia Gold Mines Inc. was commissioned in March, 1985. By Canadian standards the concentrator is highly automated, however, unlike the retrofit systems in many other plants, the Hernia process control system was installed during plant construction. This paper describes the Hernia control system beginning with system development (justification, architecture, start up, etc.), proceeding to current applications (crushing, grinding, leaching, etc.) and finally discusses some of the short term objectives for system improvement.INTRODUCTIONThe Hernia Gold Mines Inc. operation is located in the Marathon area of Northwestern Ontario. Controlled by Noranda Minerals Inc. (50.1 %), the cost of bringing the mine into production was nearly $300 million. A unique feature of the mine development was the extraordinarily short elapsed time of three years from Noranda's initial involvement to the start of milling operations. Additional background information on this project can be found in the trade literature (e.g. Tinter (1986). Scales (1987).)The Hernia concentrator is designed to process 3000 tpd of ore and commenced operation in March, 1985. Figure 1 provides a general plant flowsheet indicating the major circuits. Typical annual production statistics are included on the figure and these have been extrapolated from the available 1987 year-to-date data. Larsen and Tessier (1986) have previously described the operational aspects of the mill.In a metaphorical sense, the Hernia concentrator is like the traditional bride, ""wearing something old (e.g. the cyanide leach process), something new (e.g. a plant wide digital control system installed during construction), something borrowed (e.g. crushers from Gaspe) and something blue (e.g. the cladding on the surface buildings). While the prospect of fully undressing this bride is of considerable interest, here we choose to focus on something new. In particular, we choose to examine the process control system in some detail since Hernia is one of Canada's more highly autcmated gold mills. The control system is of interest because it has received suostantial credit for maximizing metal production and minimizing operating costs. With reference to the latter, it is worthy of note that Hem lo reports recent operating costs of less than $100 U.S./oz."

Jan 1, 1988

By P. J. van Staden

Several differences exist between the columns used for laboratory simulations of heap leaching and commercial heaps. Column walls support part of the weight of the ore and restrict the particle packing arrangements. Columns are typically of a diameter that is smaller than the dripper spacing to be used on the commercial heaps. The stacking practices that cause segregation and stratification on heaps are absent from columns. Intuitively, these physical differences would be expected to be the reasons behind the observed differences between column and heap leaching performance. But how can they be quantified, and what is the magnitude of the differences? Could some of these differences be built into column leaching experiments in order to better simulate commercial-scale heap leaching performance to ease the scale-up calculations from column leaching data? Alternatively, could heap construction practices be improved so that the ideal performance obtained in columns could be emulated on heaps? Data from a few heap leaching cases studies that permit direct comparisons between column and heap leaching performance is analysed, to reveal the extent of the differences in resistance to mass transfer. Discussion is provided on the implications for column and heap leaching practice, and for scale-up design procedures. INTRODUCTION Differences have been known to exist between leaching performance observed in laboratory columns and that of commercial-scale heaps. Both the heap leaching kinetics and finally achievable extent of extraction are generally found to be inferior in heaps compared to that achieved in columns. Heap leaching design engineers extrapolate the anticipated heap leaching performance by multiplying the time-axis of a column-leaching curve by a factor of about 2 and the extraction-axis by a factor of about 0.8, as explained by Jansen and Taylor (2002), Scheffel (2002), John (2011) and Scheffel, Guzmán, and Dreier (2016). The procedure is illustrated in Figure 1 by means of a hypothetical example. The solid line represents the leaching performance observed in a laboratory column, and the dashed line represents the anticipated leaching performance of a heap, extrapolated from the column leaching data using these empirical scale-up factors.

Jan 1, 2019

By N. W. Xu, C. Sha, F. Dai, Y. G. Zhu, B. Li

Underground caverns stability and excavatability of rock masses are of significance in geotechnical engineering, in both design and construction stages. Risks associated with underground group caverns of Houziyan hydropower station in southwestern China are growing as a result of continuous excavation-induced unloading. To improve our understanding of the underground caverns instability and resolve the complex subsurface conditions of the highly fractured rock mass, a high resolution microseismic monitoring system was established in the deep underground caverns, pursuing the relationship between the measured data about microseismic activity and excavation damage zones of surrounding rock mass. Through analyzing the tempo-spatial distribution of microseismic activity, excavation damage zones and potential risk regions in underground caverns were identified. Furthermore, the correlation between microseismic activity and pre-existing geological structures, as well as traditional monitoring was analyzed. In order to validate the correlation between seismicity and potential slip surface of underground caverns, a model was implemented into numerical code to further evaluate the deformation and stability of surrounding rock mass. The monitoring results demonstrate that microseismic events mainly occur at high stress concentration regions, which coincides with the results obtained from numerical analysis. Therefore, the comprehensive method incorporating microseismic monitoring and numerical analysis, as well as traditional monitoring and filed observation has been proven to be very promising in deformation and even instability prediction of surrounding rock mass in underground caverns subject to delineation of potential slip surfaces and excavation damage zones.

Jan 1, 2015

By V. I. Lakshmanan

Rare earth elements and yttrium (REEs+Y) are being used in the making of hybrid electric cars, catalytic converters, wind power generators, LEDs, hard disc drives, flat panel displays, and portable electronics. Currently China produces more than 95% of REEs+Y, which has made REEs+Y a critical strategic resource. Process Research ORTECH Inc. (PRO) has developed the innovative mixed-chloride (HCl+MgCl2) solvent extraction processes for recovery of REEs+Y from their ores. The HCl leaching system provides the opportunity to regenerate the acid, while the presence of MgCl2 in the lixiviant enhances the activity of the hydrogen ion by orders of magnitude, making the lixiviant very aggressive and resulting in high recoveries of REEs+Y. Solvent extraction steps are used for separation and purification of REEs+Y from other value metals or impurities including iron, zirconium, hafnium, uranium, thorium, niobium, tantalum and titanium. Direct individual separation of REEs+Y in a mixed chloride system allows avoiding the additional process steps of precipitation and dissolution in HCl. The resulting process has a simplified flow sheet that is closed-loop and environmentally friendly.

Jan 1, 2014

By H. A. Kishawy, S. Kannan, M. Balazinski

Metal Matrix Composites (MMCs) are new generation engineering materials that possess superior physical and mechanical properties compared to nonreinforced alloys. However, the presence of abrasive ceramic reinforcements in the ductile matrix causes severe tool wear and premature tool failure. Flank wear was found to be the dominant wear mode while the main wear mechanism was abrasion. Analysis of the cutting tools using scanning electron microscopy has shown that both two body and three body abrasion are operational during machining MMCs. A methodology for predicting the tool flank wear progression during bar turning ofMMCs was presented in an earlier paper [1]. In the proposed model, the wear volume due to two body and three body abrasion mechanisms was formulated. Then, the flank wear rate was quantified by considering the tool geometry in 3D turning. The main objective of this paper is to investigate the contribution of two body and three body abrasion towards the tool wear volume during cutting MMCs.

Jan 1, 2006

"This paper discusses the use of risk assessment and risk management techniques within the Australian underground coal mining industry, within the context of geotechnical risk. The industry works within a pro-active, “enabling” legislative framework, where companies and management apply a range of risk assessment tools as part of their everyday management processes. Different geotechnical risk factors and approaches are reviewed, together with application examples – ranging from mine planning and design, operations, and accident investigations.A particularly powerful resource in each of the above stages of geotechnical management is the RISKGATE system. RISKGATE is an assembled “body of knowledge” structured under different topics across the Australian coal industry, of which three topic areas address rock mechanics issues for both the underground and surface mining sector. This paper will provide an overview of RISKGATE in the context of risk-based rock mechanics applications in underground coal mining."

Jan 1, 2015

By M. Silva, G. Olivares

In a leach pile, the drainage layer or commonly known as the cover layer has been a matter of discussion due to the multiple phenomena or events that occur within it which impacts negatively the leaching process. All these events are directly related to the loss of draining capacity and irregular flow net due to an excessive compaction and entrapment of fines reducing the flow velocity which in turn cause more fines to get trapped. Over time the problem will continue to worsen rapidly and accelerating continuously like a geometric progression. When the cover layer gets to a certain level of deterioration, the only alternative to continue operating safely is to replace the entire cover material, a huge cost for any mining operation. TESRA has developed a solution to counteract the accelerated advance of the deterioration of the drainage layer. The solution consists of using large agricultural tractors coupled to a proprietary design of a heavy- duty subsoiler-ripper for deep tillage for loosening and breaking up the ground at various depth and with different legs spacing from 0.4 m or above. Also, if the ground still requires additional breaking, TESRA proposes the use of a rototiller that breaks any lumps to homogenize the ground to a certain particle size. With the subsoiler-ripper/rototiller combination equipment a layer of 0.5 m deep is properly treated to match closely the original conditions of the ground thus regaining the flow net as close as to the original seepage condition. Once the ripping is completed the subsoiler-ripper tool is replaced with another that is similar to a plow and thus continue with the installation of drainage pipes. The tool digs a Y-type profile trench allowing the pipe to sit precisely at the bottom of the trench, contributing additional lateral and lower support. This tool controls the installation depth of the drainage pipe at different inclination grades and also eliminating any irregularities that may block the flow of the leaching solution. Sometimes the obstructions block completely the flow of the solution. The main result of this methodology is the reduction of groundwater levels and at least 2% less humidity in the leaching gravel due to an increase in the draining capacity of cover. The methodology developed by TESRA applied during a couple of cycles of a dynamic leach pile has proven to be a real alternative to remedy and recuperate the cover close to its original conditions. The methodology requires only one large tractor and two accessories operated in different stages while replacing the more traditional and less efficient machinery such as the Bulldozer, Motor-grader, and backhoes.

Jan 1, 2019

By K. G. Wheeland, K. G. Byberg

The occurrence of a secondary, dust-fuelled explosion following blasting of sulphide ores has been reported in mines in many countries, including canada, the USA, Australia and South Africa. However there has been little effort to document the events and develop effective control technology. Following a detailed investigation of an incident at the Geco Di vision of Noranda Minerals Inc. , the company held a conference of interested parties in October 1986 to review the state-of-the-art and to agree on action. '!his paper outlines the causes and effects of such explosions, the key conference points and conclusions, and subsequent information-exchange and teclmology-developrnent activities.

May 11, 1988

By Z. Q. Yue

Many large rock avalanches and/or landslides have occurred in mountainous regions around the world. Their occurrences are normally rapid and unexpected, which can cause disasters. They have been investigated extensively by many researchers and engineers since the 1903 Frank Slide on Turtle Mountain, Alberta, Canada. They are one of the most peculiar phenomena because the rock debris of more than one million m3 can move over the horizontal distances exceeding those expected from conventional friction physics. This paper presents a gas cause hypothesis responsible for the large rock avalanches. It is the migration and expansion of a certain amount of highly pressurized and dense natural gas mass from deep geological grounds into the mountainous rock mass slopes. The natural gas with high pressure and density can escape from the deep geological ground and flow through faults, weak zones and/or porous channels into the rock mass forming a mountainous slope. The rock mass forming the slope has the high tensile and compressive strength and can resist the initial loading of the gas mass migrated into and stored in their voids, pores, holes, gaps, openings, apertures and cavities. With time, more and more gas mass from deep ground can migrate into and stored in the slope rock mass. Eventually, the peak equilibrium of forces and deformation reaches. The expanding power of the gas in the slope rock mass would instantly and rapidly break, erupt and/or explode them. The compressed and dense gas mass would mix, flow and expand together with the broken rock debris mass and continue offering their remaining expanding powers to the moving and sliding debris mass. As a result, the rock debris of large volume can reach the runout distances exceeding those expected from the conventional friction physics. The gas would escape into the sky and the solid rock debris would remain on the ground spreading over large ground area. The 1903 Frank Slide is examined to show this gas cause and mechanism in mountainous regions.

Jan 1, 2015