Search Documents

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By E. C. Sanford

A laboratory-scale batch extraction unit and operating procedure for studying the hot-water separation of bitumen from Athabasca tar sands are described. The extractor evolved from earlier units and has been in use by Syncrude Research for the past 10 years. By using a unit such as this, it is possible to study tar sand feed quality and the effects of chemicals on the hot-water extraction process, while process variables are held constant. Data are presented to demonstrate the importance of surfactants to the process and the interrelated role of inorganic bases and surfactants.

Jan 1, 1979

By J. Grant Spratt

THE Turner Valley gas-field, situated some thirty miles southwest of Calgary, Alberta, has been the topic of much discussion, particularly from a geological viewpoint. Several papers (1, 2, 3, 4, and 7) dealing with the structural and stratigraphical geology have already been published and are available for reference(l). In this article, the geological conditions will be treated only as they directly refer to the crude-oil prospects along the west flank of the anticline. HISTORY During the past twelve years, Turner Valley has been known mainly as a field which has produced a high-gravity naphtha from relatively large quantities of gas. For about ten years prior to the discovery of this naphtha-bearing gas, which is produced within the upper 450 feet of a dolomitic limestone of Carboniferous age, a minor production of light crude-oil was obtained from overlying sands of Cretaceous age. Up to June 1st of the present year, the field had produced 9,473,582 barrels of naphtha from approximately 829,000,000 M.c.f. of gas. For the past four years, the total daily production of 80 to 90 wells has averaged about 3,200 barrels of naphtha from 250,000 M.c.f. of gas. This is an average of 13 barrels per million cubic feet. The naphtha is extracted from the gas by ordinary gas-oil separators and absorption plants. After the naphtha has been recovered, about ten per cent of the gas is marketed for fuel to supply the cities of Calgary and lethbridge and intermediate cowns. The remaining ninety per cent is burned to the atmosphere, with the exception of some four to five million cubic feet per day which the Calgary Gas Company score in the depleted Bow Island gas-field.

Jan 1, 1936

By D. Laguitton

The basic chemistry of a1•senic related to its dissolution and subsequent precipitation in gold-mine waste waters is discussed. The lime addition methods provides the most economic treatment of arsenical slurries, but requires a careful control of the oxidation of Asm into Asv, of the pH (>12) and the filtration of the precipitate. If arsenic levels below 0.5 mg/ l are required, a modification of the method by phosphate addition must be considered.

Jan 1, 1976

By J. Stumper

The control of the distribution and movement of liquid water is crucial for increased reliability and durability of PEM fuel cells: whereas the proton exchange membrane requires a minimum amount of liquid water for optimum operation, water excess in the GDL will impede reactant gas access to the catalyst layer thereby reducing performance. In order to understand the relationships between water management on one hand and fuel cell performance and durability on the other, Ballard has been developing a number of minimally invasive techniques that can throw light on the role of liquid water for both cell performance and durability. This paper introduces a novel measurement method that can provide information about the amount and distribution of liquid water under operation. It is shown how the MEA Resistance and Electrode Diffusivity (MRED) method can be used to determine i) the amount of liquid water in the fuel cell, ii) the pure ohmic cell resistance and iii) the O2 -diffusivity of the cathode. Furthermore, through a combination of the MRED method with current mapping it is possible to determine spatially resolved MEA resistance profiles.

Jan 1, 2005

By D. B. Dreisinger, M. R. Tavakoli

Vanadium has been produced from both primary and secondary sources having various compositions. Vanadium pentoxide and vanadium trioxide are the most available and known sources of vanadium oxides. In this paper, an overview of leaching both oxides has been reported. The problem of vanadium pentoxide leaching under acid conditions is the low solubility of the dissolved vanadium. This was investigated and then supplemented with further studies of leaching at mildly basic pH’s as well as under acid reductive leaching conditions (to form vanadium (IV)). Atmospheric oxidative leaching of vanadium trioxide was investigated using oxygen and ferric ion as the oxidant. It was shown that the leaching of vanadium trioxide using oxygen is very slow; however, ferric ion can dramatically increase the kinetics and leach efficiency.

Jan 1, 2014

By Alexander Burns, David Dreisinger

The kinetics of the oxidation of uranium(IV) by oxygen gas in aqueous systems is dependent on acid concentration, oxygen partial pressure, and temperature. In order to better understand the relationship between these variables and the speed of oxidation, a series of experiments have been conducted where each parameter has been varied in turn. Data were collected continuously using UVVis spectroscopy, allowing for a detailed examination of the reaction rate over the course of each experiment. The data fit an overall apparent rate law that is 1.5order in uranium(IV), -2order in H+, first order in oxygen, and unaffected by uranium(VI). This relationship does not appear to hold for solutions with <0.2 mol/L initial acid, where a different kinetic mechanism appears to be dominant.

Jan 1, 2014

By E. M. Yates, H. M. Hamilton

"For the assent of any new mining project it is essential to determine a realistic value of revenue from the sale of concentrates.A description of the market factors influencing the concentrate terms will be presented along with a detailed review of historical terms of a smelter contract for zinc concentrates. OverviewFor the assessment of any new mining project it is essential todetermine a realistic value of revenue from the sale of concentrates.This applies at all stages of assessment through to the final feasibilitystudy. In forecasting revenue for a zinc mine the followingfactors must be considered:(a) mill recovery and zinc concentrate grade;(b) metal price forecast for all payable metals;(c) smelter terms; and(d) other selling costs.Normally, data from test work are used to determine mill recovery and concentrate grade.Market forecasting, and indeed all economic prediction is an inexact science and probably will always remain so. We have our econometric models our input/output models and a lot of other tools. But they are of no help in predicting the unpredictable. OPEC&apos;s huge increase in the price of oil was certainly the most dramatic example of this. It had a tremendous effect on the cost of producing most products world wide and on the price of these products. Any forecasts made prior to the OPEC action were obviously proven wrong."

Jan 1, 1994

By A. M. Simons

Cyanide destruction by Caro’s acid is one process commonly employed by gold operations to meet regulatory requirements and/or the International Cyanide Management Code compliance for weak acid dissociable (WAD) cyanide in cyanidation tails or waste water from such operations. Typically smallscale bench tests to evaluate and assess the suitability of the Caro’s acid destruction process are conducted. Additionally, the experimental procedure used during these preliminary investigations may also differ from that implemented at the full-scale. This paper presents the results from a fundamental investigation of the Caro’s acid process to establish a more detailed understanding of the impact that the experimental procedure has on the destruction of cyanide. In particular, it was found that the control of pH was important to avoid copper(I) cyanide precipitation at low pH and maximise WAD cyanide destruction. Residual peroxide in the preparation of Caro’s acid has the potential for subsequent cyanide destruction and could be exploited.

Jan 1, 2014

By R. P. Kofluk

The nickel-cobalt sulphides produced from limonitic laterite ores by Moa Nickel S.A. in Cuba are refined at the Corefco nickel-cobalt refinery in Canada. Significant economic implications are associated with the refining of precipitated sulphides containing elevated iron contents. The Moa Nickel S.A. operations encompass laterite mining, high pressure acid leaching (H PAL), and ultimately, precipitation of a mixed sulphide product. These processes are reviewed as they pertain to the control of iron and the formation of a mixed sulphide containing nominally 55% Ni, 5% Co and 1% Fe. The contributors to the iron content of the mixed sulphide product are reviewed; the major contributors are the HPAL operation and sulphide precipitation. The precipitation of iron during sulphide precipitation is influenced by the solution acidity, the iron and copper concentrations in the feed solution, and the presence of laterite leach solids. The significance of the copper concentration of the sulphide precipitation solutions is manifested by both physical and chemical modifications of the sulphide precipitates, presumably through the formation of fine copper sulfide seed particles.

Jan 1, 2006

By Étienne Yvenou, Martin Désilets

Le procédé d’électroaffinage du Cu est nécessaire pour atteindre les niveaux de pureté requis pour les applications les plus courantes telles que son utilisation comme conducteur électrique ou thermique.

May 2, 2024

By B. A. Watters, G. A. Parslow, F. H. Mcdougall

Carbonate-rich rocks occur at several localities within the Flin Flon volcanic sequence of the eastern Amisk Lake area. The rocks occur in two areas: as a group of small occurrences on islands within Amisk Lake and as two much larger linear belts running parallel to the regional structure east of Amisk Lake. Mineralogically, the rocks consist of talc and Ca-poor ankerite with occasional graphite. Segregation of these minerals and colour variation impart a well-defined planar fabric to the rocks and where the units are fairly continuous (e.g. Mosher Lake), their trend and attitude suggests a concordant relationship to the volcanics. Major and trace analysis of22 samples confirms the presence of two types, with one type being represented in each of the two areas. Most of the elements studied can be used to characterize the two groups, but three elements in particular give a clear separation: Mg, AI and Ni. Recalculation of the major element analyses, on a water and carbonate-f ree basis, indicates that one group (large concordant bodies with high MgO, high Ni and low AI20.J is altered ultrabasic material of peridotitic or dunitic composition. Because no relict igneous material is observed, and the contacts are apparently very sharp, it is possible that the hydration-carbonization process occurred simultaneously with intrusion, .in a closed system. The other group (small occurrences with relatively low MgO, low Ni and high AI203J represents alteration of basaltic rocks. AIthough some analyses suggest the introduction of calcium, as carbonate, along with the volatiles, the major oxides have remained remarkably stable during the alteration process(es).

Jan 1, 1981

By H. J. Chalmers

"Since the advent of large volume flotation machines, Cominco Ltd. has actively studied possible application of such machines to their various milling operations. A number of installations have been made and more are on the drawing board. This paper gives a description of these units, information as to choice of equipment, and information as to operating experience. Mechanical and operating details of six installations are summarized. Three different types of machines are discussed.Pine PointThe original Pine Point zinc flotation circuit comprised conventional roughing with two stages of cleaning. Over the years with increase in feed tonnage there have developed two adverse conditions; namely, a reduction in zinc concentrate grade coupled with an increase in MgO in the concentrate. This resulted in higher freight payments along with more severe smelter penalties. An intensive test program, in 1971, showed that the concentrate grade could be raised by 1.5 units of zinc along with a reduction in MgO from 0.8% to 0.47.. Subsequently this was done by adding two additional stages of cleaning using 16 cells of Denver 200-V's. The project was completed in January 1973 at a cost of $510,000 to give an estimated annual savings of about $390,000.Selection of the Denver Model 200-V was based on minimum floor space requirement, availability, and favourable operational and maintenance experience with Denver 100’s. As it happens it was possible to ""shoe-horn"" the 16 cells into place with a minimum of plant alteration. Some problems have been encountered with a tendency to ""sand up"" at high pH, particularly at the corners. Otherwise operational service has been very good."

Jan 1, 1974

By MAX VOS

Lithium is the lightest and electrochemically most reactive of all metals. Renewed interest in lithium coincides with research in lithium batteries and power generation by atomic fusion. Ontario lithium resources are contained in spodumene pegmatites that can form where medium- to high-grade metamorphic volcanic-sedimentary formations are intruded by pegmatite and porphyritic granitic rocks. Spodumene pegmatites occur in at least twelve locales throughout northern Ontario, all of which are in the Superior Province of the Precambrian Shield. Tantalum, cesium, rubidium, beryllium, niobium and tin also were noted with lithium in spodumene pegmatites. Considerable potential remains for discovery of additional lithium and rare-element pegmatites in northern Ontario.

Jan 1, 1984

By Louis Frost

The coal-mining industry of Nova Scotia, particularly of the island of Cape Breton, today faced as no other industry with economic problems calling for progressive engineering with production on an economic basis, must soon enter upon a phase of reorganization wherein all factors conducive to the cost of producing coal relative to the prolongation of the life of the collieries with the ultimate winning of the maximum submarine area must be closely reviewed. Bearing this in mind and applying the process of elimination to coal-mining costs generally, we are left with only three channels through which we may approach the problem of cost reduction in producing coal: (a) intensive mechanization (b) reduction in the cost of labour (c) reduction in the cost of materials. Assuming that mechanization has reached an economic stage and that labour costs have reached an economic limit, we must turn our attention to the general material costs, which may be classified as &apos;live&apos; and &apos;dead&apos; costs. The former take in all things which can be accredited with a fractional depreciation and written off the balance sheet over a period of years. On the other hand, the ?dead&apos;costs-of which the cost of supporting the underground workings form part must be completely written off: for these, no return may be expected, other than the economic return in the reduction of the cost per ton of coal produced.

Jan 1, 1928

This paper discusses three case studies conducted at Highland Valley Copper mine (HVC) that illustrate operational improvements and insights which resulted from using the McGill University gas dispersion sensors. In the first study, the superficial gas velocity (Jg) sensor was used to implement a gas profiling control strategy for the rougher, scavenger and first cleaner cells in the Cu/Mo separation circuit. The data showed a 40% reduction of down-the-bank Cu recovery at constant Mo recovery which resulted from operating the cells at the target profiles. In the second study, the bubble size analyzer was used to better understand two mechanisms of bubble formation in the two flotation columns that make up the final Mo cleaning stage: the conventional rubber-sleeve sparger and the Microcel(TM) system. The data showed a considerable reduction of bubble size in the Microcel column which resulted in a significant increase in concentrate quality (1-2% Mo absolute) and a dramatic (4-5 fold) increase in concentrate production rate compared to the typical operation. The estimated economic benefit resulting from the improved column flotation operation was an overall 4% increase in Mo circuit recovery. In the third study, real-time measurements obtained from the gas holdup and bulk density sensors were used to infer the pulp density (% solids) in a rougher cell of the bulk flotation circuit. Validation tests demonstrated that this approach provides reliable pulp density measurements. Although promising, more work is required before implementing this approach at HVC.

Jan 1, 2009

By P. Wanjara, M. Xiao

During fusion welding of aluminium alloys, the avoidance of defects (such as porosity, oxides, hot cracking, undercutting) as well as the ability to optimize the microstructure-property characteristics in the assembly are critical for the stringent manufacturing specifications in the aerospace industry. In this work, aluminium alloy (AA) 2024 was electron beam welded autogenously as part of a study to determine the influence of parametric conditions on the characteristics of the heat affected and fusion zones to obtain optimal welding conditions. In particular the evolution in the weld geometry, microstructure and mechanical properties were examined as function of the processing conditions, including beam current, beam focus, beam oscillation, linear heat input and welding speed. For optimized parametric conditions, microstructural examination of the joints revealed narrow fusion and heat-affected zones comprising of dendritic structures without the occurrence of defects that enabled a maximized joint efficiency.

Jan 1, 2006

Superconductivity, New Mexico and Mining? ? High Temperature Superconducting cables made from ?nickel tape? ? Testing on U.S. power grid ? 25 year time horizon Purpose Create awareness about the successful application of energy management systems at a Northern Ontario mine site.

May 1, 2008

By Y. Buro

The Bachelor Lake gold deposit occupies an ESE-trending, SW-dipping, silicified shear zone with hematitic alteration. It transects NE-trending, steeply dipping Archean volcanic formations and the O'Brien granite. Major W-SW and N- NE-trending faults have affected the ore zone and the emplacement of the granite intrusions. Movements along the WSW set may have opened the fractures filled by the mineralization. Gold is generally associated with pyrite. Its source, whether a granitic pluton or a volcanic sequence, is undetermined, but the granite probably provided the concentrating mechanisms through heat and hydrothermal solutions.

Jan 1, 1984

By T. A. Postolski, A. J. Sinclair

"Abstract- Two examples are used to describe how geological features impact on the development of semi-variogram models to be used for geostatistical resource/reserve estimation of porphyry-type deposits. In the Main zone of the Huckleberry porphyry copper deposit, mineralization is concentrated in fracture zones localized in volcanic rocks, along the eastern and southern margins of a granitic stock. Mineralized volcanic rocks can be subdivided into three separate domains, each with its own preferred direction of mineralization that is reflected in contoured Cu diagrams and semivariograms.The East zone at Huckleberry deposit, spatially distinct from the Main zone, is controlled by a fracture zone elongate roughly east-westerly and bounded on the south by a major fault (easterly striking and steeply dipping) across which there is a dramatic drop in grades. The eastern part of the East zone appears to be coaxial with a large intrusive body; the western part contains a small, elongate dike-like intrusion. Contoured Cu values for many levels suggest that the principal direction of geological elongation of the east and west domains of the East zone differs significantly. Independently derived semi-variogram models for each domain are different and reflect this difference in trend.In both Main and East zones of the Huckleberry deposit, block estimates by ordinary kriging are significantly different using a domain-specific semi-variogram model than using a deposit-general semi-variogram model. The domain-specific estimates are deemed better because they are based on local controls of mineralization and have less conditional bias than those generated by the depositgeneral semi-variogram model."

Jan 1, 1998