Search Documents

By Philip J. Bangerter, Chris Twigge-Molecey

Design for safety is critical to metallurgical plants, due to the inherently dangerous nature of their processes. Two significant areas of concern are: 1. preventing catastrophic process failures that cause damage or injury; and 2. operational safety that directly affects those working in or living near the plant. Process safety involves human behaviour, but the designer can eliminate or control hazards by engineering approaches, and control impacts through the design of the operating procedures. The tools available to guide safe facility design include bowtie analysis, hazard analysis, and hazard and operability studies. Clean plant design principles can guide the design process to address in-plant occupational health and safety issues. Auditing and review is a key part of the overall design process.

Jan 1, 2015

By K. Kawagishi, K. Matsumoto, Y Koizumi, H. Harada

A new burner rig for cyclic and hot corrosion testing of Ni-base superalloys and high-temperature coatings has been developed at the National Institute for Materials Science (NIMS) in Japan. The concepts of the rig design include: use of kerosene as fuel, easy operation for materials research and multi-specimen testing capability per test run. The burner rig consists of six blocks including combustion block, corrosion-solution injection block, furnace block, specimen block, controller block and outdoor facility block. During verification testing, it was confirmed that the rig had accurate specimen temperature control within ±1? from 600 to 1100? and automated easy operation. Cyclic testing of several Ni-base superalloys was conducted. The results from 50 cycle testing indicated that a new NIMS alloy developed for 1700? class gas turbine had higher oxidation resistance than CMSX-4. This new burner rig testing capability at NIMS can be very useful for future oxidation, hot corrosion and coating durability studies.

Jan 1, 2010

By Kevin C. Milne

"The solution of problems associated with development of a sour gas reserve will be of increasing importance in tl1e next few years if gas export is approved •by the National Energy Board. The purpose of this paper is to review briefly the history of the Carstairs gas field, and tCI describe in a general manner the reservoir, and the producing and processing facilities.HISTORYThe Carstairs gas field was discovered in April 1958 when the discovery well, Home Carstairs 10-17, was successfully completed as a gas well in the Elkton member of the Turner Valley formation. Geo-graphic location of the field is shown in Figure No. 1. Note that the field is about five miles west of the town of Carstairs, Alberta, which in turn is about 40 miles north of Calgary. Drilling subsequent to the discovery well resulted in three addition-al producing wells and one dry hole during I.958; two producing wells during 1959; and one producing well and one dry hole during 1960. Thus, seven producing wells and two dry holes have been drilled in the Carstairs field to date.In November 1959 a 12-section block in the Carstairs field was unitized on a surface acre basis. Mean-while, in June 1959, operators in the field executed an ""Interim Plant Agreement"" that provided the money needed to start construction of a joint venture processing plant and gathering system. Construction of the plant and gathering system was completed in February 1960."

Jan 1, 1960

By Douglas A. Sloan

"Shutdowns and breakdowns that halt the process-flow of mine production are costly. Skilled maintenance tradesmen are scarce and expensive. The cost of maintenance or of production Joss from Jack of maintenance is significant and warrants considerable managerial attention.The most appropriate maintenance policy is dependent on an economic calculation. At one end of the spectrum is the policy of avoiding all breakdowns by replacement and preventive routines before failure, such as the airlines policy. At the other end of the spectrum is the policy of minimal routines and the acceptance of a breakdown as a prelude to a repair.The complexity and cost of maintenance warrants the appointment of a maintenance manager of senior status. Within the origination, there are a number of activities that can be specialized to improve effectiveness. Among these are the inspectors' activity, the establishment of improvement routines, the planning of repair tasks, maintenance engineering research and value analysis.The maintenance system is the mechanical aid to assist the staff in the implementation of the policy. It is designed to facilitate planning to make the best use of the resources. It provides information to identify areas where managerial action is required to make improvements. The job ticket is the basis of most systems."

Jan 1, 1970

By L. Chunpongtong

ABSTRACT The mining limit in oil sands is regulated by the ratio of total mining volume (ore, interburden, and overburden) one has to mine per volume of bitumen in place (TV/BIP). This paper presents a mathematical solution for creating the most economical pit outline where the TV/BIP ratio upper limit is 12, by combining mining economic theory and the Lerchs-Grossmann (LG) algorithm.

Jan 1, 2014

By S. Komar Kawatra, Youlian Zhou, Joseph A. Halt

"Bentonite clay has been the most common binder for iron ore pellets. Although bentonite increases pellet strength and durability, it has several disadvantages. For example, its use increases the cost of pellets and decreases pellet purity due to its composition and the higher levels of flux required to meet basicity limits. Several new types of binders have been proposed to replace clay. The binders include starch, modified humic acid (MHA), and dispersants. These binders were used to pelletize a magnetite concentrate from the United States. Typical doses of each binder type were 0.05-0.1 % starch, 0.5-0.75 % MHA, and 0.05 % dispersant. At these doses, the pellets exceeded the minimum recommended values for wet drop, dry compression strength, and fired compression strength. Pellets made with the MHA and dispersants had the lowest abrasion rates of the new binders, and were comparable to pellets made with bentonite clay. In this paper, we compare the new binders, considering pellet quality and the advantages and disadvantages of each binder type.INTRODUCTIONIron ore pelletizers need binders in order to make good quality iron ore pellets. The typical binder is bentonite clay, an alumino-silicate material. Bentonite increases the ballability and strength of iron ore concentrates, but reduces pellet iron grade and reducibility. As high quality bentonites can be expensive to ship, low quality bentonites are often used at significantly higher doses – this reduces iron grade and reducibility even further. Thus, several new types of binders have been proposed to replace bentonite clay.In this paper, we present several new binders for iron ore pellets: starch and modified humic acid (MHA). These have been tested alone and in mixtures with dispersants, or else with bentonite clay. Starch, MHA and their mixtures are briefly described below."

Jan 1, 2016

By M. Santaluce

"The revamp of critical process assets that require a significant plant outage (shutdown) presents a unique and demanding set of challenges for plant operators. They are executed in a more complex Brownfield environment, typically with limited working space and often involve unknown conditions or scope. For plant operators, such a project is often a high cost event both in terms of opportunity cost of lost production and the resource cost of labor and materials. It can also be a high risk event in terms safety, environment, and future plant reliability/availability. This impacts current and future performance or Overall Equipment Effectiveness (OEE). In our experience, the sequential nature of the EPCM approach does not provide the proper framework to facilitate the level of coordination, stakeholder cooperation and detailed planning required to adequately address the construction and shutdown complexity of a critical asset revamp projects. This paper proposes a more integrated approach to handling shutdown revamps of critical assets. Its main thesis is to involve the key performing stakeholder groups early in the project lifecycle (engineering team, procurement team, construction team and plant operations) to form an integrated shutdown management team that is focused on ensuring delivered results are aligned with project objectives. In this model, the construction team executing the shutdown/construction is preparing the detailed shutdown/construction planning concurrently with detailed engineering and procurement planning. This allows construction/shutdown requirements to influence engineering and procurement, with the desire to optimize safety, speed, quality and cost. The paper also discusses how to overcome the procurement hurdle in applying such an approach. The outcome of this integrated approach is better planning, coordination, communication and alignment between the project stakeholders, a shutdown/construction driven planning approach that more fully addresses the challenges of these projects and delivered results that are aligned with project objectives."

Jan 1, 2015

By T. C. Holmes

"Dome mine, in the Porcupine mining camp of northern Ontario, is one of the important gold mines of Canada, its production of gold from the commencement in 1910 to the end of 1946 having a value of $149,000,000.GENERAL GEOLOGYThe oldest rocks in the mine are greenstones of Keewatin age(l). Those to the south are known as the southern greenstones, but little is known of their structure. Those in the northwest part of Fig. 1 and the north part of Fig. 2 are known as the northern greenstones or greenstone 'nose'. They face north, dip steeply north, and end to the east against an unconformity which pitches northeast about 20°. The volcanics are overlain unconformably by Timiskaming .conglomerate and slate. All these rocks are cut by porphyry. Closely associated with the porphyry is a group of rocks that have suffered extreme alteration. Diabase dykes intrude all the other rocks and the ore. The principal massive rocks in the mine are two adjacent flows known asthe andesite (south) and dacite (Fig. 1). They are composed chiefly ofmassive, medium-grained lava. Pillows, flow lines, and other typically volcanicfeatures are found along the tops of both flows and at other places in theandesite. These parts nearly everywhere show a slight schistosity panllelwith the flows except in the orebodies, where they are massive."

Jan 1, 1954

TIPS FOR SUCCESSFUL WASTE MANAGEMENT ? WASTE MANAGEMENT PLANS ? Define the question to be asked in waste characterization studies ? Calibrate assessments and designs with field conditions ? Ensure consistent with short, medium and long-term mine plans ? Design robust plans - goalposts and expectations will change ? Fully assess and integrate costs into economic models ? Integrate waste specialists into the feasibility and design teams ? Keep it simple and when you can?t, communicate it in simple terms ? PLAN EXECUTION ? Integrate the waste management plan into daily mine operations ? Identify the critical KPI?s , track them and set clear action triggers ? Know the difference between knowledge and data ?make sure you retain knowledge and document the important Maintain management, engineering and operational focus through the mine life

May 1, 2010

By L. Mercier, R. Narendrula, F. Desmarais, L. Amaratunga, A. Aledresse

Thiosulfate is recognized as a promising alternative lixiviant to cyanide for the extraction of gold from ore bodies. Gold thiosulfate ([Au(S2O3)2]2), however, is not well-adsorbed by activated charcoal, making industrial scale use of thiosulfate for gold leaching impractical at present. Because of their high specific surface areas (500-1000 m2g-1) and uniform open-framework nanoporosity (pore channel diameters in the range 3-10 nm), functionalized mesoporous silicas are widely recognized as highly effective materials for the selective, rapid and high capacity uptake of mercury, gold and platinum group ions. In the present work, the efficient and rapid adsorption of gold thiosulfate by thiol-functionalized mesoporous silica (hereafter designated MP-HMS) is demonstrated, whereby the thiol groups in the materials bind with the gold complexes by ligand displacement. The adsorbed gold could be leached out using cyanide, regenerating the adsorbent for further uptake cycles. Functionalized mesoporous silica is thus a promising candidate for the preconcentration of gold from thiosulfate leachate solutions.

Jan 1, 2011

By G. Itoh, S. Fukasawa

The Al-Zn-Mg alloys have been known to be susceptible to stress corrosion cracking (SCC), which is based on intergranular cracking arisen from hydrogen embrittlement (HE). The mechanism of HE has not been fully understood yet. In order to elucidate the mechanism of HE, we need to investigate the behavior of hydrogen in the alloys. In this paper, behavior of hydrogen in an Al-5.8%Zn-2.4Mg alloy was investigated by means of hydrogen microprint technique, a method to visualize location of hydrogen emission from specimen surface as silver particles. One side of the tensile test pieces was electrolytically polished and then covered with photographic emulsion. Hydrogen was pre-introduced into the test pieces from opposite side by cathodic electrolytic charging for 30min. Then, the test pieces were stretched with continuing the charging. After that, the specimen was fixed, rinsed, dried and observed with a scanning electron microscope. As a result, silver particles were observed on some grain boundaries.

Jan 1, 2015

By R. Kamguem

The surface of a mechanical part plays an important role in determining performance in service. The presence of scratches left by the cutting or tearing of the material on the surface of the workpiece supports the concentration of stress and strain. This article presents the experimental study for high speed milling of the aluminum alloy 7075-T6, using cutting tools different by the nose radius and coatings (TiCN, TiAIN, TiCN + A12O3 + TiN). A multi levels factorial design of experiment (DOE) and statistical analysis was used. The roughness parameters investigated are Ra, Ra, Rv, Rc, Rsm, and Rk. The results show that the feed rate, the types of coatings and the geometry of the cutting tools have the most significant impact on the surface roughness profil. Surface finish charts according to feeds and cutting speeds were established for each tool tested.

Jan 1, 2011

By G. R. Davidge

"Falconbridge Mine has a history of significant microseismic activity dating back to 1955. Since mid-1981, a microseismic monitoring system has been operating in the area around the No .9 Shaft hoist room located 25 m from the are zone at a depth of 1200m. Several mine wide faults dissect this area and have been shown to be microseismic-active due to mining. The microseismic monitor has been interfaced with a small dedicated personal computer and a communications device to perform routine data evaluation and to produce graphical output. The programs are described and selected result s from the monitoring program are presented.IntroductionFalconbridge Mine is located on the southeast rim of the Sudbury Basin. The nickel-copper sulphide ore zone is essentially a tabular orebody striking approximately east-west and dipping at 80 degrees north near surface and rolling to 75 degrees to 80 degree s south by the 1000 level. (Mine level number s represent the approximate depth in feet below ground surface .) This dip is maintained down to the 6000 level. The north wall is comprised of jointed norite and a faulted contact up to 1 m thick exists between the ore zone and the norite. The south wall rock is a greenstone with highly siliceous lenses and often has a faulted contact with the ore zone. No less than five mine wide faults exist, as shown in Fig. I.Mining ha s been carried out from virtually the bedrock contact to depths of 1830 m although the majority of current activity is between 900 and 1500 m below surface. A winze provides access below the 4025 level and the cage hoist room is located on the 3850 level in the north wall 25 m from the contact. Because of concern for the stability of this hoist room, there has been no mining activity within 60 m of the hoist room and by 1980 this block of ore was one of the major blocks of high-grade ore remaining in the mine . Mining of this block was originally scheduled for very late in the decade.Prior to a six-month shutdown in 1982, this mine produced approximately 450,000 tonnes of ore annually, mainly by cut and- fill techniques. Following the shutdown, annual production has been reduced to approximately 200,000 tonnes and production is now mainly by undercut and fill techniques .Mining-induced seismicity has occurred at Falconbridge Mine since at least 1955 and reviews of the microseismic problems for the periods from 1965 - 1970 and from 1971 to 1979 were made by Singh (1971) and Vongpaisal et al. (1980), respectively. The need for instrumentation was addressed by these authors. Following several large events during the spring of 1980, a decision was made to investigate existing microseismic monitors and to apply micro seismic monitoring techniques in Falconbridge Mine. Application of microseismic monitoring to Falconbridge Mine was to concentrate on the No . 9 Shaft hoist room area of the mine, particularly around the 4025 level where a large mechanized cut-and- fill stope was approaching this level. By mid - 1981, the microseismic monitor was fully installed and with in a year , a short-period seismograph and a personal computer had been added to the system."

Jan 1, 1984

By Y. Thibault, L. Morin, R. Cameron, D. Gould

"There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite tailings in the Sudbury area alone, with an average nickel grade ~0.8% (plus cobalt). Pyrrhotite is a highly reactive sulphide mineral that has the potential to generate acidity; consequently, it is stored in large tailings ponds that require perpetual treatment to avoid the production of acidic drainage. Re-processing this material using bioleaching technologies has the potential to recover valuable metals, while reducing the toxicity, reactivity, and acid generating potential of the remaining residues. CanmetMINING is currently developing a stirred-tank bioleaching process to recovery nickel and cobalt from pyrrhotite-rich tailings. Stirred-tank experiments have been conducted with one tailings sample over a range of pH and temperature conditions, resulting in 80 to 90% and 70 to 80% leaching of nickel and cobalt respectively in 10 days.INTRODUCTION Sulphide tailings may represent a significant financial liability for mining companies as these wastes may produce acidic drainage under some disposal conditions. As a result, the companies must post financial bonds large enough to ensure there are sufficient funds for perpetual management of these wastes. At the same time, there are billions of dollars in metals incorporated into these mining wastes waiting to become valorized. Many sulphide tailings are amendable to bacterial oxidation for metal extraction. Re-processing of tailings using bacterial leaching has the potential to recover valuable metals from waste; and reduce the toxicity, the reactivity, and the acid generating potential of the remaining residue. By reprocessing these wastes there is an opportunity to significantly reduce liabilities and financial assurance bonds, while recovering metal values. There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite-rich tailings in the Sudbury area alone with an average nickel grade ~0.8% (Peek et al., 2011) plus cobalt and copper. Pyrrhotite is separated from pentlandite concentrates by magnetic separation and flotation. It is already finely ground and has often been segregated from other tailings material, making „mining? relatively inexpensive. This represents roughly (> $100/ton) in contained value, with negligible mining costs. This paper reports on the development of a stirred-tank bioleaching process for recovering nickel and cobalt from pyrrhoitite-rich tailings, which is currently underway at Canmet MINING."

Jan 1, 2017

By Finley A. Campbell

"Nickel-copper sulphide deposits associated with basic rocks in the Quill Greek area and the White River area in the Yukon Territory have been studied and compared from the view-point of their general geology, structural geology, and the mineralogy of the ores. The relative amounts of the major constituents, magnesium, iron and calcium, and the minor constituents, nickel, cobalt and chromium have been determined spectrographically for two cross sections of the basic rocks at Quill Creek and one at White River. These data, along with petrologic and field evidence, were used to determine the sill and dyke-like character and nature of the basic intrusions. Loss on ignition is employed as a measure of the degree of serpentinization. The distribution determined shows that the serpentinization does not appear to have greatly influenced the inferred original distribution and lithophile associations of magnesium and nickel. The cobalt content may have been altered.The nickel content of the serpentinized peridotites ranges from an average of 0.36 per cent in one section to an average of 0.24 per cent in each of the other two sections studied. The cobalt averages 0.0038 per cent in the samples from the two Quill Creek sections and averages 0.0042 per cent at White River. These results have been compared with other available data.The sulphide ores are later than both the peridotite and gabbroic rocks and may be co-magmatic with them. There is no evidence in these areas to support an origin by lateral secretion; on the contrary, the alteration associated with the ores, the mineralogy and spatial relationship to basic and ultrabasic rocks, indicate the ores are derived from a basic magma."

Jan 1, 1960

By A. Gourlie

"This paper describes the performance properties of a new 95 ksi minimum yield strength, oil well casing grade designed specifically to resist hydrogen sulphide stress corrosion cracking, SSCc. The new grade, Soo-95SS, demonstrates NACE Tensile threshold values greater than 90% specified minimum yield strength, SMYS, and NACE Bent Beam values in excess of 12.7 x 1()4 psi. The new Soo-9588 grade also exhibits superior collapse and notch toughness values. IntroductionIn recent years, a trend toward casing grade specialization has resulted in the introduction of numerous proprietary grades designed specifically for particular production environments, In response, Algoma Steel has developed, as part of a "" grade for service"" philosophy, two new 95 ksi minimum yield grades. The two grades are Soo-95, High Collapse (HC), and Sour Service (SS). This paper describes the development of Soo-95 Sour Service.Four main objectives were established:1. Definition of the steelmaking and continuous cast processing practices2. Determination of the acceptable maximum and minimum levels for all chemical elements3. Definition of special processing requirements4. Definition of the physical characteristics and ranges of the product properties.This paper provides a description of the experimental approach, followed by a presentation and discussion of the trial results . Finally, a number of conclusions are given."

Jan 1, 1988

By Henrik Saxén, Mikko Helle

The operation of hot stoves used for preheating the blast in the ironmaking blast furnace has a strong effect on the consumption of reductants, economic performance of and CO2 emissions from the steelmaking site. Generally, it is recommended to maintain as high blast temperature as possible, because this minimizes the rate of reductants in the blast furnace. The blast temperature is affected in a complex way by the time periods of heating and cooling of the stoves, and by the amount of gas combusted in the stoves. Furthermore, as the hot stoves show degraded performance with age, it is a non-trivial task to select optimal operation parameters for the stoves. The paper addresses this computationally by applying a one-dimensional heat-transfer model of the hot stoves for optimization of the performance of the system. The complexity and strong coupling of the decision variables is demonstrated by numerical examples, where the blast temperature is maximized under different constraints.

Jan 1, 2015

By Y. Rama Murthy, Amit Ranjan, Pankaj Satija, Sunil K. Tripathy

"Chromite ore is one of the essential raw materials for ferroalloy and steel industry. Boula-Nuasahi belt of Sukinda region, Odisha, is the only resource of chrome ore in India. The Indian deposits are typically characterized as ferruginous and siliceous type ores. Chrome ore is generally mined by open cast mechanized mining method in these areas. The run-off-mine (ROM) ore from the various mines is sent to beneficiation plant via stack yard for further up gradation. The chrome ore beneficiation plant (COB) has two major circuits: comminution (feed preparation) circuit and beneficiation circuit. In the comminution circuit, the ore is reduced to <1 mm size ( for complete liberation of chromite) from -220 mm size in stage wise crushing (primary and secondary crusher) followed by screening and single stage grinding in a ball mill. Fraction having size <1 mm is further upgraded in the beneficiation circuit to produce three different concentrates having specific chemical composition and Cr: Fe ratio. The beneficiation plant is a complex circuit comprising of combination of unit operations (spiral concentrator, Floatex density separator, hydrocyclone, wet shaking tables). In the recent years the overall performance efficiency (grade and recovery) of the beneficiation circuit got affected with numerous changes in the run-off-mine ore quality (physical and chemical), mineralogical composition, etc.In this article, attempts made for improving the performance of chrome ore beneficiation circuit is discussed. The approach adopted and practical problems encountered while the process were also highlighted. The results of the trials has shown an improvement in the performance of the cyclone (d50 : 56 µm – 40 µm) and chromite losses into tailing to <12%.INTRODUCTIONChromite has a wide range of application, from refractories to metallurgical industries, and from chemical to non-ferrous alloy industries. Chromium ore (Fe2+, Mg) [Cr, Al, Fe3+]2O4) occurs exclusively in rocks formed by the intrusion and solidification of molten lava or magma which is very rich in the heavy, iron containing minerals such as pyroxene and olivine. With the richness of silica and iron, the chrome ores are broadly classified as siliceous type and ferruginous type. Pure chromite with composition FeCr2O4 is rare because magnesium usually substitutes for ferrous ion and aluminum and ferrous ion substitutes for chromium. Generally the associated gangue minerals are talc, quartz, hematite, goethite, limonite, gabro, serpentine, anorthosite, dunite, pyroxinite, etc. Around 96% of the chromite ore production is consumed for metallurgical applications of which 94% is converted into different grades of ferrochrome i.e., high carbon ferrochrome and charge chrome as shown in Figure 1. Stainless steel being the leading consumer of ferrochrome, any change in the dynamics of the stainless steel industry impacts overall chrome ore demands significantly."

Jan 1, 2016

By WENDY MARTIN

The Eastern Townships and Asbestos Hill areas are the current asbestos-producing districts of Quebec. Mining in the two areas began in the /are 1870s and 1972 respectively. Production from the Eastern Townships is derived from rhe Serpentine Zone of ulrramafic rocks, specifically from basal serpentinized peridotite members of what are now considered to be allochrhonous ophiolitic material that was abducted onto the Early Ordovician continental margin. From south west to northeast, the rhree allochthonous asbestos-producing sections of the Serpentine Zone are designated the Asbestos Ophiolite Complex, the Thetford Mines Ophiolite Complex and the Pennington Dyke; the Pennington Dyke is considered to represent a segment of serpentinized Alpine peridotire that was fragmenred from a larger, more complete ophiolire complex. The Asbesros Hill deposir on the Ungava Peninsula lies in what apparenrly is an inrrusive sill found wirhin rhe Chukorar Group, the uppermosr group of Precambrian-aged Cape SmithWakeham Bay Belr of volcanic-sedimentary rocks.

Jan 1, 1984

By Vic Briccardi

Energy Management Challenges The Holistic Standard to Energy Management Energy Management Information System (EMIS) "Best Practices?: Energy Management Maturity Curve De Beers Canada Profile & Mine Locations Significant ROI Driven by Real-Time Energy Visibility Mining Energy KPI?s Summary: What Does EMIS Deliver? Q&A Session

May 1, 2013