Search Documents

By E. Czech

Hydrogen generated through aluminum-assisted water split reaction is a novel, efficient and environmentally friendly method. It has been found previously that the passivation of aluminum can be prevented in neutral (pH=7) or near neutral pH conditions in water by grinding aluminum with a catalyst, such as A12O3, SiO2 or SiC. Recently, the best results have been obtained by using water-soluble inorganic salts (WIS), ground with aluminum. The massive, rapid corrosion reaction of the Al-WIS system which takes place in regular tap (or marine, or ground) water can be utilized to produce hydrogen by aluminum-assisted water split reaction, in-situ, on-demand. The reaction offers clean, low-cost, environmentally benign and entirely recyclable technology for on-board on-demand hydrogen generation. Besides pure gaseous hydrogen, only pure solid aluminum hydroxides AlOOH or Al(OH)3 are formed as the reaction products. The hydrogen yield and Al-WIS reaction efficiency are high. From 1 g of mechanically alloyed aluminum powder, up to 1.25 liters of hydrogen were generated, i.e. efficiency up to 92% was achieved. The amount of hydrogen and hydrogen generation rate depend on various reaction parameters. The effect of chemistry and concentration of additives, water temperature, powder particle size and milling conditions on the reaction kinetics will be presented and the possible process mechanism will be discussed.

Jan 1, 2005

By J. R. Foster

Investigations into the effect of a variety of acid digestions on common rock-forming minerals demonstrated a considerable variation in the proportion of the total metal extracted. A similar situation applies to the analysis of a number of common rock types. In addition, grain-size variation has an effect on the amount extracted by certain digestions. This work indicates that considerable care needs to be given to selecting an appropriate acid digestion capable of determining metal held in particular components of a sample. By using partial extraction techniques, the identification of certain patterns of metal distribution, undetectable by normal methods involving total metal analysis, may be achieved.

Jan 1, 1973

By K. Horikawa, S. Kitahata, H. Kobayashi

"It has been clarified that the Al-5%Mg alloys containing 200 mass ppm of sodium showed grain boundary (GB) fracture, even when tested at room temperature, as well as at high temperatures (~500°C). SEM/EDX study revealed that the GB fracture was associated with the segregation of sodium on grain boundaries of the Al-Mg base alloys. Differential scanning calorimetry (DSC) revealed that the GB fracture at room temperature of Al-Mg alloys was caused by sodium segregation in the solid state. It was also shown that the tendency of the GB fracture strongly depended on the heat treatment; the alloys after the solution heat treatment showed severe GB fracture compared with the alloys after the homogenizing treatment. Moreover, it was shown that the GB fracture at room temperature by sodium segregation was suppressed by the addition of bismuth or indium. The suppression of the GB fracture by the additional elements was believed to be the scavenging effects by forming the sodium bearing compounds in grains.INTRODUCTIONIt is widely known that Al-Mg base alloys containing high amount of magnesium(~5 mass%)show better workability at room temperature, while that the alloys show grain boundary (GB) embrittlement at higher temperatures ranging from 200 to 500°C, depending on grain size(Otsuka, 1984), sodium impurity level(Ransley, 1959, Okada, 1997, Horikawa, 2001)and testing strain rate(Yamada, 2012). In the case of coarse-grained Al-5%Mg alloys (~300 ?m), 2 mass ppm of sodium causes severe GB fracture around 300°C, however, the Al-5%Mg-2ppm alloy does not show GB fracture at room temperature. It has also been shown that the GB embrittlement caused by 2ppm of sodium was suppressed by the additional elements, such as bismuth (Talbot, 1995), antimony (Ueda, 1997) and indium (Horikawa, 2012). Basedon these facts, we have concluded that the GB embrittlement at higher temperatures of Al-Mg alloys is attributed to the synergy effects of GB segregation of atomic sodium and GB sliding. For the GB embrittlement mechanism of Al-Mg alloys, involvement of low melting point metallic phases has been pointed out (Lynch, 2002),since the GB embrittlement appeared only at high temperatures. Up to date, the effects of high amount of sodium addition more than 2 ppm on GB fracture were not fully investigated in Al-Mg alloys. In the present study, the effect of 100 ppm ordered sodium impurity on GB fracture of Al-5%Mg alloys was examined, together with the effect of another additional elements."

Jan 1, 2017

By James Tuer, John R. Goode, Jim Cambon

"Hudson Resources Inc. (Hudson) has defined a major resource of high purity anorthosite (calcium feldspar) assaying about 30% Al2O3 at the White Mountain (Naajat) deposit in Western Greenland. Extensive beneficiation and evaluation testwork has shown that the material can be simply beneficiated to produce a feed material ideal for the production of low-alkali E-glass used for making glass fibre. An offtake agreement is in place with a major US fibreglass manufacturer and, subject to the mine construction schedule, shipments are scheduled for late 2016 or early 2017. In parallel with the E-glass program, Hudson has completed an initial program of metallurgical testwork which shows that the White Mountain anorthosite can be processed by hydro- and pyro-metallurgical processes to yield either smelter-grade alumina (SGA), suitable for conversion to aluminium metal, or a high purity, chemical/specialty-grade alpha-alumina (CGA) commanding a premium price. The process includes dissolution of the anorthosite in hydrochloric acid, HCl sparging to precipitate aluminium chloride hexahydrate (ACH), recycle of the ACH filtrate to leaching with a bleed stream processed for HCl regeneration from CaCl2, and two-stage calcination of the ACH to regenerate HCl and produce SGA and/or CGA. Calcium silicate and amorphous silica are marketable by-products. This paper discusses the White Mountain anorthosite deposit; the process testwork completed to develop production processes for SGA and CGA; production plans, and indicative economics.INTRODUCTIONHudson Resources Inc. (Hudson) holds a 100% interest in the Naajat Exploitation Licence in Western Greenland that cover the White Mountain high-calcic anorthosite deposit. Anorthosite is a calcium aluminosilicate of slightly variable composition but generally containing about 30% Al2O3. The alumina content is similar to that in bauxite and anorthosite has long been studied as a feedstock for the production of alumina. Other potential uses include feedstock for the high-end fiberglass (E-glass) industry and as a filler for use in paint and plastics."

Jan 1, 2016

By Grazyna Zakrzewska-Trznadel

The paper outlines the main objectives of the project that concern the evaluation of the possibility of uranium production from indigenous resources since Poland enters the nuclear program. The best available technologies are considered for uranium extraction and obtaining the yellow cake - U3O8. Liquid-liquid extraction with novel extracting agents, as well as membrane processes for separation of by-products will be tested in course of the project. The technological part will be completed with techno-economical analysis. Acknowledgement The studies were supported by the POIG project, No 01.01.02-14-094-09-00 ?Analysis of the possibility of uranium supply from domestic resources?.

Aug 1, 2010

By K. Bachmann, M. Rudolph, U. A. Peuker, H. H. Duong, T. Heinig, T. Leißner, H. Schubert, Helmholtz-Institute Freiberg for Resource Technology, Technische Universität Bergakademie Freiberg

"Minerals can be liberated by random fracture of particles into smaller fragments or by detachment along phase boundaries. These two mechanisms represent borderline cases. When ores get comminuted the liberation of minerals is achieved to some extent by both mechanisms. This article describes a method to determine the extent of transgranular and intergranular fracture on surface exposure of minerals based on 2-dimensional liberation analysis.The approach uses the non-biased surface information like phase specific surface area (PSSA), phase specific free surface (PSFS) and phase specific locked surface (PSLS) of minerals and their change with comminution. The amount of transgranular and intergranular fracture on surface exposure can be calculated using the phase specific surface parameters.A sedimentary rock (apatite ore), an igneous rock (nepheline-syenite) and an artificial material (copper slags) were ground to different fineness. Based on the mineral liberation analysis (MLA) of feed and products, the extent of phase boundary fracture on the surface exposure of the minerals is studied.INTRODUCTIONMinerals can be liberated ether by comminution or by detachment (Gaudin, 1939). Liberation by comminution is a random fracture mechanism, which is not being influenced by ore texture, grain boundaries and mineral features (transgranular fracture). Liberation by detachment represents a fracture along grain boundaries (intergranular fracture). Random fracture often is named as the dominating mechanism for the liberation of ore minerals. This has been the basis to simplify models for liberation modelling (Barbery, 1991; King, 1979; Meloy, 1984) assuming that the probability of cracks moving along grain boundaries is zero. Thus, no interfacial area is lost during comminution."

Jan 1, 2016

By J E. McMynn

The development of the Granduc mine presents a number of problems which are peculiar to its location and surrounding terrain. Because the development tunnels portal onto an area which is covered by an extensive glacier, and the mountain-side is subjected to dangerous snow slides, it was decided to construct an underground powerhouse to supply the necessary electric power and compressed air. This paper deals with the special problems inherent in the design and -construction of an underground plant. It involves the installation of diesel-electric generating equipment having an aggregate capacity of 1,050 kw.,and of air compressors with a total capacity of 2,400 cfm. Items dis-cussed include the selection of equipment to meet site conditions, the ventilation and cooling of the underground room, and the protection of personnel and equipment from explosions and fire. A short discussion on the automatic supervisory and alarm installation is also included. THE Granduc mine is located 135 miles north of Prince Rupert and 25 miles north of Stew-art. This seems quite accessible, mileage-wise, but, due to mountains,

Jan 1, 1963

By M. A. Hardie

"CASES and mixtures of them are so common and so much a part of everyday existence that they become so taken for granted that their individual characteristics and idiosyncrasies rarely become of curiosity to others than those involved in tl1eir production, processing, treatment, transportation, and for utilization. The use of the most common and universal mixture of gases -air -is begun at birth by ail living creatures and their discontinuation of its use terminates existence. Modern man rides on air in his tires, rides through it for high-speed transportation, and uses it for his comfort in the heating and air conditioning of his domicile. It is neither the aim nor the in-tent, in the next few moments, to provide a panacea for even a portion of the problems inherent in the gas industry nor to delve deeply into any particular facet of its diversities. The purpose is primarily to touch upon some of the peculiarities and generally to consider approaches to employ in the pursuit of solutions."

Jan 1, 1959

By John C. Luck Jr.

"DEVELOPMENT of oil emulsion mud dates back to the early days of rotary drilling when oil was added to the drilling mud solely for the purpose of freeing stuck drill pipe. After the drill pipe was freed, and drilling resumed, this oil was considered a contaminant. Efforts were made to remove the oil but some of it remained and was emulsified with the drilling mud, thus forming a mechanical emulsion.During the late 1930's, operators found that adding crude oil to drilling muds seemed to alleviate 'sticky-hole' problems and so oil was allowed to remain in the mud. This practice was adopted when it was found that faster drilling rates and longer bit life were obtained. These observations led to the development of emulsion drilling muds. During the past five years their application has become more widespread because of the lower fluid losses obtained, greater lubrication qualities, faster penetration rates, and generally better hole conditions.An emulsion may be defined as a two-phase system consisting of a mixture of either finely divided oil droplets in water or of finely divided water droplets in oil. The surrounding liquid is known as the continuous phase. The emulsifiers reduce the interfacial tension, making the droplets tend to repel each other so that they remain dispersed and stabilized. These emulsions are classified as oil-in-water or as water-in-oil, depending upon whether water or oil, respectively, is the continuous phase. Briefly, close inspection shows that they consist essentially of globules of• the one liquid suspended in a continuous mass of the other liquid. Oil emulsion muds are usually of the oil-in-water type. Two basic types of emulsifiers •commonly used in Canadian muds are soaps and lignites."

Jan 1, 1954

By J. B. Mawdsley

"AbstractThe uraninite-bearing deposits in the Charlebois Lake area of northeastern Saskatchewan are unusual and important concentrations of uranium. They were first discovered in 1949 and preliminary development work to the end of the 1951 field season indicates the probability that this will become •another uranium producing district. The deposits are in zones bordering granite masses. These zones are of migmatite (mixed rocks) composed of calcium-rich meta-sediments intruded and replaced by a fine-grained white pegmatite. Locally this pegmatite is replaced by an end fraction which is relatively rich in fine-grained disseminated uraninite; it is these occurrences that constitute the bodies of economic interest.The fine-grained white pegmatite contains plagioclase feldspar more lime-rich than that in the granites of which it is an end differentiate. This extra lime, evidently derived from the intruded sediments, would result in the raising of the temperature of crystallization of the pegmatite-forming magma, thus consolidating it rapidly near the granite contacts as a fine-grained pegmatite. The end liquor containing uranium was evidently locally concentrated in minor fracture zones in these pegmatites. Where no lime sediments were present. the coarse-grained alkaline pegmatites were formed. Their crystallization would not be accelerated and the uranium would tend not to be localized in the pegmatite but to migrate and consolidate at lower temperatures with the end products, possibly in some instances as pitchblende veins."

Jan 1, 1952

By Gae On Kim, Ki Baik Kim, Suk Hoon Kang, Tae Kyu Kim, Sanghoon Noh

"Advanced radiation resistant oxide dispersion strengthened steel (ARROS) is being developed as a fuel cladding tube material for future nuclear reactor system applications. The research activities consist of advanced radiation resistant ODS steel development and fabrication technology development of ODS steel structural components. One candidate material with a chemical composition of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3and was selected as representative materials, and this material was named as the advanced radiation resistant ODS steel (ARROSTM).On the basis of this ODS steel composition, an optimized fabrication process of structural components such as plates, sheets and tubes has been established through various process conditions in mechanical alloying, hot/cold working, and heat treatment processes. These R&D activities are expected to contribute to the realization of ODS materials in the future.INTRODUCTIONA sodium-cooled fast reactor (SFR) is being developed at the Korea Atomic Energy Research Institute (KAERI) with a view to economics, safety, reliability, and sustainability. The prototype Gen-IV SFR with a capacity of 150 MWe is under design, and this prototype reactor is scheduled to operate from 2028. For a commercial SFR system application, it is necessary to develop an advanced structural material having both high creep strength and irradiation resistance at high temperatures (Jeong, 2014). Oxide dispersion strengthened (ODS)steel is one of the most promising structural materials because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density, which is extremely stable at high temperatures under a neutron irradiation environment for a prolonged operating period(Kim, 2016). As the first step, several batches of ODS steel were designed and the candidate samples with a 2 kg scale each were fabricated by mechanical alloying, hot isostatic pressing and hot rolling processes. The mechanical properties of these samples were evaluated. Up to now, two candidate materials with chemical compositions of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3 was selected as representative materials, and these materials were named as the advanced radiation resistant ODS steel (ARROSTM).The next step was to optimize the fabrication process of the ARROS compositions for in-core structural components such as the fuel cladding tubes of a SFR. An optimized fabrication process of fuel cladding tube with a composition of ARROS has been established through various process conditions in mechanical alloying, hot consolidation, hot/cold working and heat treatment processes. Joining technologies of the ODS steel tubes is being developed using solid-state welding such as magnetic pulse welding, friction stir welding and diffusion boding. It is expected that the development of ARROS will contribute to the realization of a commercial SFR with high economics and sufficient safety in the future. In this paper, the study of fabrication process of ARROS structural components is introduced."

Jan 1, 2017

By N. Afrin

The microstructure and tensile properties of AZ31B-H24 magnesium (Mg) alloy after friction stir welding (FSW) were evaluated. The grain size was observed to increase from approximately 5 µm to about 9 µm after FSW. The obtained Hall-Petch type relationship showed a strong grain size dependence of the hardness values. While the FSW led to about half of the yield strength of the base magnesium alloy, the ultimate tensile strength after FSW could reach about two thirds of that of the base alloy. The hardening capacity of the FSWed samples was about twice of that of the base alloy. The strain hardening exponent of the base alloy was found to be about 0.1 whereas it became larger than 0.3 for the FSWed samples. After yielding the base alloy showed a high initial and almost constant work hardening rate, corresponding to linear hardening stage II, followed by stage III with a decreasing hardening rate. Stage II linear hardening was observed to be absent in the FSWed samples.

Jan 1, 2007

By A P. Powell

This paper deals with the power plant at Cassiar Asbestos Corporation Ltd., Cassiar, B.C. It discusses the units installed in the plant, the distribution of power and the costs involved. The efficiencies and economics of this power plant are considered to be somewhat better than average. Introduction C ASSIAR Asbestos Corporation's power plant had its inception in 1952 with a 15-by 15-ft. log cabin containing two International Harvester diesel generator sets of 50 kw. total generating capacity. Over the years, it has grown to its present size -an 80 by 82 ft. by 35-ft.-high rigid-frame Butler building housing eight 2,300-volt diesel generating sets, a 2,300-volt distributing switchboard, a 550-volt auxiliary panel, three air compressors, six heat exchangers and other related equipment. The units in the power plant, numbered according to their order of placement, are rated as shown in Table I. The total generating capacity of the plant is 3,673 kw. All of the generators are of the open vertical design except that on No. 7 engine,

Jan 1, 1965

By G. A. Gross

Nearly 90 per cent of the iron ore produced in Canada is derived from iron-formation or bedded iron deposits. About 70 per cent of this consists of concentrates obtained fom iron-formation; another 20 per cent was formed by natural enrichment processes. Four principal varieties of iron-formation are recognized -the Algoma, Superior, Clinton and Minette types. Differences in their geology, mineralogy, chemical composition and environment of deposition are of special significance in their evaluation as ore.

Feb 1, 1966

By D. A. Barr

"The Galore Creek copper deposits are situated in the Stikine River district, 640 miles northwest of Vancouver, British Columbia. The deposits are primary cupriferous replacements localized in highly fractured zones lying in altered sedimentary, extrusive and intrusive rocks near the contacts of a potash-rich syenite porphyry complex which forms the core of a structural dome in Upper Triassic volcanic and sedimentary rocks. Ten deposits are distributed over an area of 3.5 by 2 miles and through an elevation range of 4,000 feet. The deposits share many of the characteristic features common to both the porphyry copper type of mineralization and pyrometasomatic deposits.Primary mineralization includes chalcopyrite and bornite, and is associated principally with pyrite and magnetite. The daminant alteration products are hydrothermal biotite and potash feldspar. Gypsum, anhydrite, garnet, chlorite and carbonate are commonly associated with sulphide minerals. Copper oxides, al-though present, are quantitatively of minor importance. The distribution of certain of the primary minerals reveals hypogene zoning characteristics.The results of stream sediment surveys, and airborne magnetic, ground magnetic and induced polarization surveys show important relationships to geologic structure and mineral deposits."

Jan 1, 1966

By David J. T. Carson

"The metalliferous deposits of Vancouver Island have generally been assigned to the Mesozoic ""Coast Range Orogeny."" However, a metallogenic study by the writer has revealed that several important classes are early or middle Tertiary. Included are porphyry coppers, and gold-quartz, arsenic and copper-arsenic veins.The porphyry coppers and many gold-quartz veins are within and adjacent to Oligocene-Eocene quartz diorite intrusive complexes. Arsenic and copper-arsenic veins have a close spatial relationship to sills and laccoliths of Oligocene dacite porphyry which intrude the late Cretaceous Nanaimo Group.Other deposits of demonstrable Tertiary age include a molybdenum stockwork related to a relatively potassic Eocene plug and a few small copper-skarn occurrences. Some copper stockworks and a mercury deposit are probably also Tertiary.The copper deposits of previously recognized Tertiary age are those of the Sooke area that occur in Eocene basalts and Oligocene gabbros."

Jan 1, 1969

By Randy Billing, J. Fraser Wilson

"IntroductionThe job of designing and implementing effective environmental management sounds like what one executive, assuming responsibility for a very sick organization with lots of potential described as, ""an insurmountable opportunity"".Effective environmental management is an opportunity, no doubt. Its an unusual, if not unique opportunity. Insurmountable? Maybe not! Indeed, in the authors' experience, the keys to unlocking this opportunity are not in new or complicated technicalities; they are in the existing strengths and successful experience that one has in managing other complex and exacting management issues.To begin, it is necessary to understand what these issues of sustainable development mean to business. What is the nature of this opportunity? What makes it look unsurmountable?New Games: New RulesLawyers have described some of the new rules companies are facing and there is a new game being played; a game characterized by unique challenges.Take two, for example: • The ecological problems to be faced are Mother Nature's business, the political solutions required are our business. This combination of natural problems and political solutions requires the development of new management mechanisms, to bridge the gaps among us, as individuals, as professions, as interest groups and so on; indeed, even as countries;• and gaps there are : about as many gaps as the people involved : many of them with new and changing expectations, often mutually exclusive and not negotiable.The challenge of these relationships and communications among so many different interests is one of the keys to effective environmental management.Like any game, this one has rules and they are new, too. These rules are evident not just in new legislation - tough legislation with draconian penalties; they are also evident in new and exacting business policies, value driven and just as unforgiving of poor performance. Senior management of many companies are speaking about the role of enlightened corporate policies and how important it is for everyone involved that these policies drive and reflect business practices. Absence of day to- day behaviour which evidences the words in action, the policy on the wall of a corporate office or published in an Annual Report is first evidence for the prosecution , not the defence.The challenge of practical policies is another key to effective environmental management.This is a new game, with new rules: the challenge of change."

Jan 1, 1991

By X. Xe, B. Myhre, N. Zhou, B. Sandberg, Z. Chen

Effects of microsilica and reactive alumina type on flowability, flow decay and working time of Al2O3-SiC-C castables for blast furnace trough were investigated. The results show that at a targeted self flow values of (80 ± 10)%, water demand markedly decreases with increased microsilica addition. The nature of reactive alumina has a strong influence on flowability of the castables. Higher microsilica content contributes to a longer working time. The flow decays gradually until the working time and then drops abruptly. In addition, microsilica have positive effect on both cold strength and hot strength.

Jan 1, 2004

By John B. Riddell

"AN EXCELLENT review of the status of applied geochemistry was given by Warren (1959) at last year's General Meeting of the C.I.M. The purpose of this paper is to present recent developments and trends. Several important books were announced during 1958: Ginzburg, I. I. Principles of geo-chemical prospecting. (In process of translation from the Russian by V. Sokoloff).Vinogradov, A. P. The geochemistry of rare and zvidely scattered chemical elements in soils. Consultants Bureau, N.Y. Korzhinskii, D. S. Physicochemical basis of the analysis of the paragenesis of minerals. Consultants Bureau, N.Y.In addition to these translations Mason's Geochemistry' has been revised, and Hawkes and Webb (personal communication) are publishing a book on geochemical exploration. A Symposium on Geochemistry was head in Paris in July, 1957, in conjunction with the XVIth International Congress of Pure and Al-lied Geochemistry. The abstracts of the papers presented at this Symposium were published in Geochimica et Cosmocl1imica Acta, 1958, Vol. 14, pp. 150-167."

Jan 1, 1960

By G. A. Gross

DURING the past 5 years a large amount of money and effort has been expended in exploration of iron-formations and in testing their suitability for beneficiation. Beds of ferruginous material are numerous and widely distributed in the Precambrian rocks of Canada and practically all of the known iron ranges or belts have been examined to a limited degree at least in an effort to evaluate their potential as sources of iron ore. A number of favorable beds have been selected for mining on completion of surface sampling, diamond drilling, extensive metallurgical testing and economic studies, and many other ranges are being studied. There are still a great many iron-formations that have not been evaluated by modern concentration methods and their regional extent is not fully known. The iron-formations are easily located by airborne or ground magnetic surveys but the main task in finding a mineable ore-body of this type amounts to locating a bed sufficiently large for mining which consists of material that can be concentrated economically by modern beneficiating methods. The ease with which an iron-formation can be concentrated to give a marketable ore depends primarily

Jan 1, 1961