Search Documents

By G. W. Govier

Measurements of the settling rates and the rheological behaviour of heavy media formed of fine suspensions in water of each of magnetite, ferrosilicon, and galena have been made. For media ranging from 1.6 to 2.8 specific gravity the settling measurements gave initial settling rates of from 0.5 to 0.01 ?cm. 'Per minute for magnetite; from 4.0 to 0.8 cm. per minute for galena; and from 35 to 1.6 cm. 'Per minute for ferrosilicon. These measurements indicate the ?relative stability of the suspensions and should be helpful in establishing the useful specific gravity range for each medium. Measurements of the consistency of the media were made with a Fann Model 35 rotational viscometer. Aibnormal or non-Newtonian behaviour was observed in the case of each media, the apparent viscosity being dependent upon the rate of shear or the intensity of motion. Measurements were made over the rate of shear range of 10? to 1,000 reciprocal seconds. The apparent viscosities of the magnetite media ranged from 450 down to 4?0 centipoise at 2.30 specific gravity, and from 2,450 down to 700 centipoise at 2.80 specific gravity. In the case of the galena media, the variation was from 40, through a minimum of 6, to 10 centipoise at 2.20 specific gravity, and from 950, through a minimum of 180, to 450 centipoise at 3.6 specific gravity. The ferrosilicon suspensions exhibited apparent viscosities ranging from 42, through a minimum of 5.6, to 9 centipoise at 1.9 specific gravity, and from 160, though a minimum of 35, to 85 centipoise at 2.8 specific gravity. The dependency of apparent viscosity or consistency upon intensity of motion is considered to be of particular significance in applications of heavy media where the medium is in rapid motion.

Jan 1, 1957

By R. W. Boyle

"PREFACEThis paper comprises two parts. The first part discusses lithochemical surveys based on major, minor and trace elements in whole-rock samples from primary enveloping halos. The second part continues with discussions of surveys based on leakage halos, zonation of elements, stable and radioactive isotopic distributions, geothermometric, geobarometric, thermolumin escent, pedochemical, hydrochemical, atmochemical and biogeochemical methods. A selected bibliography follows the second part of the paper.ABSTRACTAreal (two-dimensional) geochemical surveys, based mainly on secondary dispersion halos and trains in media such as surface waters, soils and drainage sediments, have proven particularly successful in recent years and have greatly assisted in the discovery of a large number of varied mineral deposits. Three-dimensional surveys based on primary halos and leakage halos have received relatively little attention by research organizations and the mineral industry. Such surveys offer many novel approaches for discovering blind mineral deposits deeply buried below overburden or within their host bedrocks. This paper reviews detailed methods for the discovery of blind mineral deposits based on sampling rocks (lithochemical methods), soils and other types of overburden (pedochemical methods), waters (hydrochemical methods), gases (atmochemical methods) and biological materials (biogeochemical methods) . All are applicable to the discovery of blind deposits; the efficacy of each or in combination depends essentially on the type of mineralization, the extent of the development of the primary and secondary dispersion halos, and the finances available for sampling techniques employing overburden drilling, bedrock drilling, and sophisticated water, gas and vegetation collection."

Jan 1, 1982

Abstract - A method to extract certain types of error variance information from paired data is presented, which constitutes an important tool for the calibration of Gy’s formula for variance predictions in the sampling of broken ores. The research summarized here complements publications by others on geochemical precision. The model and method proposed for treating duplicate data provide a practical means of deriving separate estimates of the purely analytical and aliquot sampling variances, from a unique set of duplicate assays, and, hence, proposes a new avenue for estimating effective mineral grain size.

Jan 1, 1998

By F. Vahdatikhaki

Simulation techniques have offered significant boosts toward a cost-and-time-optimized planning of construction projects by enabling project managers to effectively comprehend the behavior of projects. Using historic data from projects of like nature, simulation considers uncertainties involved in a project through accommodating the stochastic modeling parameters. However, the heavy reliance on the statistical data and not taking into account the context-specific features of the project cause the degradation in the realism and accuracy of the simulation models. Similarly, the extent to which a historic pattern could be retrofitted to new projects will decrease in line with the growing uniqueness of the projects and the novelty of construction methods. Furthermore, the existing real-time simulation frameworks are not capable of distinguishing the transient environmental changes, with minimal long-term impacts on the productivity, from the influential changes that will greatly impact an operation. In addition, existing simulation tools are devoid of location awareness, resulting in the inability to consider safety threats in their representation of the project. To address these issues, this research proposes a framework based on the integration of new tracking technologies used in Automated Machine Guidance (AMG) with simulation-driven 4D modeling methods. The proposed framework automates the adjustment of the simulation model based on the updated data from the site, and thus transforms simulation from a predictive tool used at the planning phase to a proactive monitoring platform usable throughout the planning and construction phases. A prototype is developed to test and demonstrate the effectiveness of the proposed approach.

Aug 1, 2013

By D. F. Kidd

Introduction In a companion article, Surveys at Great Bear Lake, 1931, R. C. McDonald has described the general character, topography, and climate of the Great Bear Lake-Coppermine River area and the main means of access (l). The present paper will largely be confined to the geological features of the district. In the last two years, the rocks of the region have received considerable attention, and papers including references to .the geological succession have been written by Knight(2), Duncan(3), Norris( 4), Reid(5), Cameron(6),and Kidd(7). The writer confined his field-work during the 1931 season to the district between LaBine point and Hunter bay and northwest to the head of McTavish arm. Brief trips were made down the Sloan river from McLaren lake, 25 miles northeast of Hunter bay, to that place, to Dowdell (Sixty-six) point, the south point of Echo bay, and to the region north of the Dismal lakes and west of the Coppermine river. The inner part of Echo bay, which is the area discussed by Reid and Cameron, has not been seen by the writer and the geology there will not be discussed.

Jan 1, 1932

By C. Gosselin, M. Rheault, M. Benoit, Y. Bouroubi, V. Sarago

The last three decades have seen significant mining development in northern regions of Canada, where the freeze and thaw cycle of permafrost and the corresponding surface subsidence and heave represent a significant challenge to the design and maintenance of infrastructures. Identifying areas at risk is of great assistance to reduce the impact of this issue. Over the past ten years, Synthetic Aperture Radar Interferometry (InSAR) has been widely used to monitor ground surface deformation. With this technique, changes in phase between two SAR acquisitions are used to detect centimeter to millimeter surface displacements over a large area and with high spatial resolution. InSAR can be used as a tool to assist the siting and design of new infrastructure as well as highlighting the risk to existing structures in areas of unstable terrain. This paper presents the results of a project carried out by Effigis, which made use of SAR interferometry in the context of monitoring terrain and infrastructure stability in a northern mining environment that is affected by permafrost seasonal and long term changes. TerraSAR-X images acquired during two periods, August to November 2012 and March to October 2013, were used to measure the deformations and/or movement of ground surface, infrastructure and stockpiles caused by seasonal changes in permafrost extent in and around a mining site located in Nunavik, Quebec. The results showed that spatial and temporal distributions of surface displacements are in accordance with scientific and terrain knowledge. Some displacements were observed in loose soil areas while, as expected, none were detected in bedrock and rock outcrop areas. The areas most affected by active layer changes showed surface subsidence in the thaw settlement period. This study confirms that SAR interferometry has a great potential for operational applications related to risks induced by surface deformation in mining environments. It shows that this technique can be used to produce reliable maps of surface movement and monitor the vertical displacement of important infrastructure.

Jan 1, 2015

By G. D. Mcdowell, L. B. Cochrane, B. D. Thompson

"Abstract - Exploration for deep underground copper and nickel sulfide deposits in the Sudbury mining camp is carried out with surface drilling. More detailed drilling, with an advanced underground exploration program, may be necessary to establish an accurate interpretation of the deposit geology and upgrade the resource estimate to the measured category for reserve estimation and feasibility assessment. Resource evaluation is a lengthy and costly process that could result in a decision not to proceed with the project. For projects that proceed to production, significant reductions in the operating and capital costs could be achieved with a more accurate interpretative model of the deposit geology and mineralization. Quality control procedures to ensure the integrity of the drilling data and interpretation guidelines are essential steps in the development of a deposit model. The use of block modeling techniques and the application of geostatistics for resource estimation further improve the quality of the resource model.Significant improvements to the interpretive models can also be achieved by incorporating additional information from geophysical measurements to validate and constrain the geological interpretation. The geophysical models must be consistent with known geological environments and oreforming processes, which has required the concurrent development of comparative models from exploited deposits. These geophysical techniques can also provide key geotechnical information required for the optimum design of the mining method and mining sequence. The objective of this program is to improve the accuracy of the deposit model and the quality of the resource and reserve estimates in order to optimize capital investments and reduce the development and operating costs of underground mining projects. Several of these techniques are currently being tested at INCO Limited’s Sudbury operations. The results from those tests are presented and their applications are discussed within the framework of resource/reserve classification systems and project evaluation objectives."

Jan 1, 1998

By A. Ignatieff

This is the first in a series of Coal Technology Reviews being prepared in accordance with a recommendation voted by the Coal Division in session at the Jubilee Meeting, Vancouver, April, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review' of Coal Technology, for distribution among those concerned in the production and use of coal in Canada. This recommendation was subsequently endorsed both by the Council of the Institute and by the Dominion Coal Board. Further reviews (or digests) will appear at intervals in the Bulletin, or will be published and distributed by the Board which, meanwhile, has undertaken to distribute reprints of Mr. Ignatieff's review.-En. * * * The fields in coal mining technology which are considered to demand most attention and study at the present time are reviewed under the headings appearing below. Mechanization In the light of the growing shortage of skilled miners and the necessity of mitigating constantly increasing mining costs, interest continues to centre in mining methods and applications of mechanization chat will produce the maximum reduction of man power. The growth of strip or open-cut mining, also, is a consequence of this trend. Mechanization at the face attracts most attention and the trend is toward developing and adopting machines capable of cutting and loading the coal in one operation instead of having the separate operations of cutting, drilling, blasting, and loading. In Great Britain, where longwall mining is? the general practice, the A.B. Meco-Moore machine still receives much attention, and accounts describing its performance over reasonably long periods have appeared in the technical press.

Jan 1, 1948

By Charles B. Newmarch

Abstract In the course of coal studies undertaken by the B.C. Department of Mines in southeastern British Columbia, special attention was directed to problems of coal seam correlation. Methods that had been used successfully in other coalfields were found, in the Crowsnest area, to have a restricted use or furnished only additional evidence that might prove helpful when used in conjunction with other criteria. A correlation technique involving semi-quantitative spectrographic analyses of coal ashes was developed. Elements detected in the ash include Si, B, P, Fe, Mg, Mn, Pb, Ti, Cr, Ga, Ca, Al, Ge, Ba, Mo, V, Ag, ?y;b, Na, Zn, Zr, Ni, Sr, Cu, K. Of these, the elements found to be most useful in correlation were Na, Ba, Si, V, and Mg. The element Na was invariably detected in the ash from one of the seams but was not found in samples taken from any of the others. In all of the four seams sampled statistically, significant differences in the amount of certain trace elements were noted. When the values obtained for these trace elements were portrayed in the form of histograms, the resulting diagrams had a characteristic shape for each seam. The diagrams provided a basis for seam identification within the limited area (8,000 feet by 4,000 feet) that was investigated. Introduction During the field seasons of 1946, 1947, and 1948 the British Columbia Department of Mines undertook a geological investigation of the coal measures of southeastern B.C. As field work progressed in the Crowsnest area it was found that, within the Kootenay formation, which contains all the commercial seams of the region, the coal beds are the most persistent stratigraphic units. Because of relatively rapid changes in ?both the thickness of the seams and the interval between seams, difficulty has invariably been experienced in attempts at correlation. Even short-range correlati0ns by able geologists who have worked in the Crowsnest coal basin have been questioned by the operating companies. It was apparent, therefore, that a more dependable correlation technique was needed so that stratigraphic and structural studies could be of greatest value. This paper presents, firstly, a summary of the results obtained in attempted correlations using methods that have been found effective in other coalfields. Secondly, a method based on semi-quantitative spectrographic analysis of coal ash is described and the apparently promising results are discussed.

Jan 1, 1950

By W. J. Mcgaughey, M. A. Vallée

"Abstract -The application of geophysical technology to resource delineation aims to improve the quality of resource/reserve estimates by integrating high-resolution survey methods, geophysical modeling and inversion with three-dimensional representations of geological and mineral deposit data. The use of geophysics can cost-effectively improve a geological interpretation based only on geological and sampling data. Success depends upon the ability to use geological visualization and modeling software, first to develop a three-dimensional geological model and then to modify it interactively by integrating geophysical data with the geological and sampling data.The high resolution required for mineral delineation geophysics results in a focus on borehole seismic and high-frequency electromagnetic methods. Borehole wireline logging is used to develop an understanding of the relationship between physical properties and geological description. Data from core samples and borehole wireline logs allow the construction of a three-dimensional physical property distribution, consistent with the existing geological interpretation. The three-dimensional physical property distribution is used for both geophysical forward modeling (to compare to field data) and as a starting model in iterative inversions.Advanced visualization techniques allow the simultaneous viewing of the three-dimensional physical property model, the geological information and data from which it is derived, and the geological interpretation and the geophysical results. Geophysical results may be simulated responses from a forward model or the output from a numerical inversion in the form of an updated physical property distribution. Iterative refinement of the geological interpretation is required to ensure consistency with the geological and geophysical data. The key to success with this approach is that all relevant geological, geophysical, and rock property data reside in a common, visual model of the earth.Examples from massive sulfide deposits illustrate the benefits obtained by the integration of geophysical and geological data."

Jan 1, 1998

By L Tafaghodi Khajavi, M. Barati

The distribution of phosphorus between solid silicon and iron-silicon melt was determined to investigate the degree of phosphorus removal from silicon by solvent refining with iron-silicon alloys. The distribution coefficient which is the ratio of the mole fraction of phosphorus in solid to that of liquid is as follows: 0.22±0.02 (1310°C), 0.29±0.02 (1260°C) and 0.33±0.02 (1210°C). The removal percentage of phosphorus is: 84.2% (1310°C), 72.5% (1260°C), and 63.7% (1210°C). The average phosphorus content of produced silicon in the proposed solvent refining process would be over two times less than that of the conventional directional solidification. The values of interaction coefficient of phosphorus on iron at different temperatures were obtained as -3460±155 (1310°C), -3595±159 (1260°C) and -3694±119 (1210°C). Self interaction parameter of phosphorus at different temperatures are as follows: 68±4 (1310 ?C), 78±10 (1260 ?C) and 103±19 (1210 ?C). The calculated values for distribution coefficient of phosphorus at infinite dilution are: 0.22±0.00 (1310°C), 0.30±0.00 (1260°C) and 0.34±0.00 (1210 °C).

Jan 1, 2015

By van der Meer. F. P.

High Pressure Grinding Roll (?HPGR?) technology is applied in a broadening range of minerals processing applications for relatively wet or moist materials. HPGR grinding of dry material or involving drying and air classification is more common, for example in cement manufacturing. A number of minerals processing plants are also operating with dry material, either due to process reasons, such as considerations of preceding or subsequent process stages, or as dictated by local conditions of arid areas and scarcity of water. The present world-wide expectation of decreasing availability of water supply urges us to look for alternatives that minimize water consumption. Recently established and envisaged future HPGR applications with dry ores have indicated that the technology of dry crushing and classification as practiced in cement and limestone grinding can be applied in minerals processing. Moreover, dry technology could very well be applied for generating a final fine product at sizes near or below 100 microns, as may be required for beneficiation by, for instance, flotation, magnetic separation or tank leaching. Dry HPGR grinding requires special attention in maintaining suitable process economics, when considering power input in grinding, drying and classification. In some cases, HPGR capacity and roll surface wear life may be negatively affected by a lack of moisture in the feed. This publication summarizes some of the features of, and experiences in dry HPGR applications. This includes design aspects of the classification system and discussion of the wear protection of the roll surfaces. The paper also includes examples of operational experiences of dry practices in minerals processing and cement plants.

Jan 1, 2012

By G. V. Theja, V. B. Maji

Large infrastructure projects like tunnel excavations, underground constructions face innumerable risks. For successful completion of these projects, it is essential that we foresee and understand risks that could occur during different phases of the project. One of the risks affecting underground excavation projects is the inaccurate performance prediction of TBMs. As this could severely affect the project, resulting in lower advance rates and could also result in changing the excavation machine or method, due to difficulties in excavation, thereby increasing the overall cost of tunnelling. This makes performance prediction of the TBMs as one of the crucial aspects in tunnelling, as a precise estimation of its performance is required for planning and estimation of time and cost of the tunnelling projects. This performance prediction of TBM is a challenging geotechnical problem that is intricate and complex in nature, this is possibly due to the fact that TBM performance prediction involves understanding the rock fragmentation process in wide range from micro-scale (i.e. the interaction of surface of rock material and cutter tip) to macro-scale (including the interaction of rock mass and TBM). Thus in order for the performance prediction model to be efficient, parameters of both TBM specifications and ground conditions have to be considered. Various models have been proposed by researchers since the early phases of TBM application, these studies resulted in the development and improvement of numerous penetration prediction models. Most of these models consider the geotechnical parameters that are input to the model to be consistent along the TBM drive and neglect the uncertainties in parameters that occur. And so to improve the predictive capability of these models and to incorporate the above uncertainties, the penetration rate is modeled as a stochastic variable depending on the geotechnical and TBM parameters, its statistical distribution is determined and is used to characterize the penetration rate instead.

Jan 1, 2015

By A. Shakoor, T. P. Gautam

The long-term slaking behavior of clay-bearing rocks in the field can be quite different than the short-term slaking behavior in the laboratory. To assess this difference, 12 replicate samples of each of 20 clay-bearing rocks, including 5 claystones, 5 mudstones, 5 siltstones, and 5 shales, were exposed to natural climatic conditions for 12 months. After each month of exposure, one replicate sample of each rock was removed from natural exposure and its grain size distribution was determined. Disintegration ratio (DR), defined as the ratio of the area under the grain size distribution curve of the slaked material for a given rock to the total area encompassing all grain size distribution curves of the tested samples, was used to quantify the amount of disintegration under natural climatic conditions. DR values of naturally exposed samples were then compared with the corresponding values of second-cycle slake durability index (Id2) determined in the laboratory. The relationship between Id2 and DR after, 1 month of exposure, exhibits an R2 value of 0.65 but the relationship deteriorates when DR values for 6 and 12 months of exposure are used, with R2 values of 0.63 and 0.25, respectively. However, when DR values for laboratory samples, computed from grain size distributions of slaked material after second cycle, are compared with DR values of naturally exposed samples for the three periods of exposure, the relationship improves with the corresponding R2 values being 0.61, 0.71, and 0.41. These results suggest that DR may be a better parameter for assessing the long-term disintegration behavior of clay-bearing rocks than Id2.

Jan 1, 2015

By P. Zhang, K. Liu, L. Ou

"The strength and mechanism of Portland cement prepared from stone coal vanadium slag were studied in this paper. Initially, the slag was used as silicon raw materials to prepare clinker. By blending the prepared clinker with gypsum, waste, and fly ash, a series of different grades cement got well prepared. All of performances of the cement were up to the requirements of China’s national standard. The hydration products and microstructure of cement were identified and analyzed by X-ray diffraction and scanning electron microscopy. With the comparison of cement hydration characteristics at different ages, the strength formation mechanism of cement was clarified. The experimental results suggested that adding the fine materials (mainly waste and fly ash) to replace part of clinker would accelerate cement hydration, as it provided additional surfaces for the nucleation and growth of hydration products. And the hydration products were similar to ordinary Portland cement, mainly containing the amorphous calcium silicate hydrates (C-S-H), acicular ettringite (AFt) and portlandite (CH). With hydration time increasing, the hydration products continuously covered the cement particles, resulting in a thicker surface layer. As a result, it gradually condensed into a dense structure block with small pores and smooth surfaces, which led to higher strength. In conclusion, using the vanadium slag to prepare Portland cement can realize the utilization of solid mineral wastes, which will bring huge ecological and economic benefits.INTRODUCTIONWith the development of China’s mining industry, more and more mineral waste residue is discharged every year. These solid wastes cause varieties of resources and environmental problems on people’s living area. While at the same time, the demands of cement are increasing with the remarkable development of the construction industry. Thus, in recent years, utilization of proper solid waste to prepare cement has become an efficient way to deal with the solid mineral wastes problems (Boncukcuoglu, Kocakeri?M, & Tosunoglu, 2002; Simatupang, Hanafi, Purwasasmita, Imran, & Pane, 2012; Tsakiridis, Papadimitriou, Tsivilis, & Koroneos, 2008; Yun, Yong, Choi, Lee, & Lachemi, 2009)."

Jan 1, 2016

By X. L. Song, G. W. Zhang, F. Y. He, X. Xiao, L. L. Huang

This paper presents the design of a model and process simulation of a vertical mill based on a population balance model. The simulator, Simulink, which is a systematic modeling tool within MATLAB, was used for the simulation. The model will simulate the real time variation trend of each size fraction in the feed material to the vertical mill, as well as, the size distribution of the batch grinding products. Breakage distribution and selection functions are calculated based on batch grinding laboratory experiments using Back-calculation method. The simulated size distributions correspond with those in the actual mill operation having a relative error of less than 0.50%. This work lays the foundation for future research on modelling and simulation of a closed circuit grinding operation consisting of a vertical mill with hydrocyclone classifier.

Jan 1, 2016

By J. O. Yeboah, V. Boakye, P. A. Bepswa, M. Lombard, G. Nutor

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013

By Charles Kingsley

THE PRESIDENT (DR. C. B. KINGSTON, member C.l.M.M.) expressed regret that neither of the authors of the paper was able to be present to submit the paper in person. In their absence, it would be introduced formally from the Chair. It was a clear, straightforward account of a fine piece of shaft sinking, cleverly conceived and boldly executed. He referred briefly to the distribution and nature of the Dome ore-bodies and stated that, for both the miner and the metallurgist, the mine had provided a wide range of problems of unusual interest. Discussion on the paper was then invited. MR. THOMAS PRYOR said the paper was most opportune, because the subject of internal shafts did not appear to be fully treated in current mining literature. Many members were not familiar with Canadian gold deposits and it would be of interest if the authors could give a brief description of the location of the ere deposits of the Dome mine. This information would doubtless explain why a new internal shaft was needed in a position which required such an exceptionally long cross-cut to connect it to the main hoisting shaft to surface. It would also add to the value of the paper if the authors would give some idea of the duty expected of the new shaft in terms of tons of rock hoisted and of trips engaged in the transport of men and materials, and it would be helpful if figures could be given of the total capital cost of the hoists and subsidiary excavations at the shaft top, and of the cost per foot for sinking and lining the shaft below the collar. Turning to details of the paper, one was favourably impressed by the care given to the provision of a good travelling way for men in the main cross-cut, as shown in Figure 1. It was by no means always that one could walk in comfort and safety in a working where there was a 20-in. ventilating pipe in the roof.

Jan 1, 1939

By T. E. W. Nind

"A short description of the chamber lift method for producing oil wells is followed by some comments on compressor requirements and gas utilization. A quantitative analysis of the process is presented and, based on this analysis, criteria are suggested for selecting wells for which this type of lift might be suitable. The analysis leads to the conclusions that chamber lift is an efficient producing mechanism for wells having very low productivity indices (say about 0.05 bbl/d/ p.s.i. or less), but that for such wells optimum utilization of injection gas cannot be attained. It is suggested that the gas injection time per cycle should be kept as low as possible, compatible with a small oil fallback volume, and that the cycle frequency should be in the range of 20-40 cycles/ day. For wells with productivity indices of 0.2 bbl/d/p.s.i. or higher, chamber lift is relatively inefficient; how-ever, if well allowables are low it may offer an attractive, low cost, alternative to gas lift or pumping."

Jan 1, 1960