Search Documents

By W. G. McBride

INTRODUCTION Preparation of this article, at the request of the Committee on papers, has been undertaken in the hope that it may stir up helpful discussion and constructive criticism. The Canadian mining industry is in the dumps and there is no use trying to deny the fact; nor does it help to say that other industries are in as bad or a worse condition. Let us face the situation honestly and see just how serious it is. The entire financial and industrial world is in a state of depression. The gravity of the case is no doubt exaggerated by contrast with the wave of optimism and false prosperity which pre-ceded it. The prevailing gloom and pessimism are just as irrational as was the former super-optimism. As far as we mining engineers are concerned, the causes are quite beyond our control, and it is the effect upon our own industry which interests us most. This effect is an accumulation of mineral products with consequent depression in price to a point where profits have almost, if not quite, disappeared. Whether this accumulation of stocks is the result of over-production or under-consumption is difficult to say, but it would seem likely that there is a combination of the two. The introduction of selective flotation has brought about a large increase in the production of zinc, a moderate increase in the production of lead, and a comparatively small increase in copper. It has turned relatively small mines into great producers, as in the case of the Sullivan, revived expiring mines like La Cananea, and brought-in new ones like Flin Flon

Jan 1, 1931

By P. F. Venus

In December 1977, a large pillar was removed by blasthole mining methods at lnco's Creighton No. 3 mine. Although the 2,363.000-ton blast was not a size record for a single underground blast at Inco, it did represent a significant departure from conventional blasthole mining. In terms of the application of nominal 6-inch-diameter boreholes underground, coupled with bulk slurry explosives, the magnitude of the blast is considered a first and very important development. The application of large-diameter boreholes in underground operations was first tried successfully in 1973. Since that time over 13/4 million feet have been drilled in this adaptation of an open-pit technique to underground operations. The blast, which required 708 holes, totalling 131,500 feet of drilling, was loaded in a six-week period, using special slurry handling techniques developed jointly by Inco and CIL. Inco operating and engineering personnel consider this application of large boreholes and slurry explosives for blasthole mining a very important milestone in modern mining technology.

Jan 1, 1978

By Gerald S. Cole

It used to be that a science/engineering presentation on "light weight" at a metallurgy conference, would relate to the materials science, processing, component fabrication and applications of aluminum, magnesium and titanium. Within the automotive industry, light weight now includes how to "lighten up", how to lightweight, or how to mass reduce vehicle components and systems. Increasingly stringent global emissions-reduction requirements require increasing vehicle fuel efficiency; mass reduction is an enabler to achieve this. While light metals certainly are the basis, a host of other materials can be used to optimize mass reduction while meeting vehicle performance, safety and cost requirements. New grades of ultrahigh strength steels and even nanosteels can be thinned down and save over 1/3 the mass vs conventional mild steels. A compacted graphite cast iron engine can be made lighter than an aluminum one. Aluminum components in vehicles were only castings; now aluminum stampings, forgings and extrusions are becoming more visible components of mass reduction. Lower mass high temperature polymers, and carbon fiber polymer composites now replace aluminum and steel. These materials often require specialized processing and manufacturing techniques to produce a component, including superplastically formed twin roll cast sheet aluminum and magnesium, and hot stamped/in-mold quenched steels. The assembly of hybrid structures requires unique joining/bonding, and corrosion-inhibiting techniques that might include sophisticated structural adhesives. This thinking "light" presentation, will conclude with a discussion of U.S. and Canadian government engineering and research support for mass reduction, including the proposed $148 M American Lightweight Materials Manufacturing Innovation Institute.

Jan 1, 2014

By G. A. Vissac

In this paper we intend to deal particularly with the economic side of coal washing as it applies to our mines. We will then discuss why the dry-cleaning process has been selected, and give a brief description of our plant, dwelling only on its specific features and referring the reader to the numerous papers published on the subject for any details on the principles and machinery used in dry cleaning. ECONOMIC DISCUSSION The washery introduces an extra cost for depreciation, operation, and loss in treatment. A certain proportion of the coal, now being sold, and which the miners have been paid for. will have to be wasted. As a whole, the total increase in cost would be approximately 60 cents per ton. On the possibility of recovering this amount depends the success of the washery. There are two advantages to be expected from the washery, the first, which occurs at the mine and which will be certain; the second, more difficult to estimate, because it depends upon convincing our customers that they should pay more for a better product.

Jan 1, 1924

By E. Laatio, W. McKay

"History of Tara Mines Ltd.Tara Exploration and Development Company Ltd. was formed in Canada by Irishmen in 1953. The discovery of an orebody approximately six miles from the historically famous Hill of Tara in County Meath was a wild dream . Nevertheless this dream became a reality. Tara Mines Ltd. was formed, and the mine developed some 35 miles northwest of the City of Dublin in the Irish Republic.Tara's original drilling program indicated a zinc-lead orebody of approximately 60 million tonnes grading at 10.1% Zn and 2.6% Pb. The terms of the mining lease stipulated that the Irish government would acquire 25% equity interest in the operation. The mine was thus owned 75% by Tara Exploration and Development Company Ltd. of which the principal shareholders were Noranda and Northgate, together with 25% being held by the Irish government. The mine was purchased in March 1986 by Outokumpu Oy, a Finnish mining and metallurgical company, and together with the 25% government stake are the current owners. Outokumpu Analysis on Tara Mines Ltd.Upon ownership Outokumpu carried out a comprehensive analysis on the operation and came to the following conclusions :1. Tara had a good orebody;2. Tara had a skilled, capable, stable workforce;3. Tara's concentrator and processing equipment was adequate to meet requirements;4. Tara's mobile equipment fleet was too old and too numerousin numbers; and5. Tara had too many employees, both staff and hourly paid .With ore reserves of approximately 50 million tonnes and at a planned extraction rate of 2.6 million tonnes it meant that the mine had a lifespan of approximately 20 years. To be a viable operation into the future, the mine had to become more efficient. Operating costs and manpower levels had to be dramatically reduced."

Jan 1, 1989

By B. C. Legg, G. L. Tiley

"Many of the ore bodies presently being developed are in remote locations and are, or will be, served by electrical power supply systems of limited capacity.The largest single components of the electrical systems of an underground mine are usually the production hoist drives; the power demands of these drives vary continuously throughout each hoisting cycle.Before 1970mine hoists were driven by either wound rotor induction motors or DC motors in conjunction with motor generator sets.Static Power conversion equipment now costs less to purchase and install and is claimed to be more efficient than motor generator sets. On the debit side, however, it can adversely affect the hoist motors, it operates at relatively low power factors, and it produces harmonic currents.This pa per discusses the effects of static equipment on both DC motors and AC power systems, and evaluates the relative consumption of the three classes of drives."

Jan 1, 1993

By R. Lovat, J. A. Hunter

"The design, development, and verification of the Lovat 7.6metre diameter full-face tunnel-boring machine is reviewed. Programmatic and technical challenges are outlined with a review of the specifications and the design to meet these requirements. Subsystem designs are presented for the waste material removal, ventilation, cutter head, structural support, advance technique, water removal, and interfaces with the Donkin-Morien Mine. The techniques used to verify that the design meets the requirements is by testing in the Lovat factory and in the field. Certification of the machine for use in a methane environment is discussed.IntroductionStudies have concluded that the average annual worldwide tunnel construction is 500 kilometres at an estimated average co st of $3,400 U.S . per linear metre. The total market value of the tunnelling industry is estimated as approximately $1.7 billion U.S. per annum. Of this, the current market for tunnelboring machine excavation is approximately $270 million U.S. per annum worldwide with a further potential of $250 million if more contractors are convinced that Tunnel-Boring Machines (TBM) are more suitable than conventional techniques. The worldwide civil tunnelling market has the potential to double each year in the next 5 to 15 years. Growth has been identified in the energy and mineral resources sectors of the economies of many nations and a significant volume of machine tunnelling studies and trials are presently underway for the extraction of coal, uranium , heavy oil or oil sand fuels, metallic and non-metallic industrial minerals and base metal or rare earth ores. Further tunnel projects for regional transportation, waterpower, irrigation , high density urban transportation, storm water sewers and water supply purposes are continually being implemented with new concepts like military security facilities and underground storage schemes being considered.Lo vat Tunnel Equipment of Rexdale, Ontario, the only Canadian manufacturer of TBMs was incorporated in 1973 to manufacture so ft ground tunnel-boring machines to satisfy this growing market demand. Lovat has produced an average of 5 machines per annum during the period 1972 - 1982 and has established an international reputation for competitive costs, quality of construction, after-sales service, and reliability. As of June 1982 Lovat TBM's have been used to tunnel over 240 km in projects throughout the world."

Jan 1, 1984

By A. S. Romaniuk

More than a decade ago, CANMET management recognized the need to make better use of existing technological information in mining and extractive metallurgy-two fields basic to the economic well-being of Canada. There were at that time no indexes or files dedicated to disseminating technical information for the many minerals mined and processed in Canada, including coal. CANMET, with the nation's largest research and library resources in the minerals field, was in a unique position to fill this need. Initial efforts were concentrated on building a mining file, beginning with identification of world sources of published information, development of a special thesaurus of terms for language control and adoption of a manual indexing/retrieval system. By early 1973, this file held 8,300 references, with source, abstract and keywords given for each reference. In mid-1973, operations were computerized. Software for indexing and retrieval by batch mode was written by CANMET staff to utilize the hardware facilities of EMR's Computer Science Centre. The resulting MINTEC file-one of the few files of technological information produced in Canada-is the basis for the national literature search service in mining offered by CANMET. Attention is now focussed on building a sister-file in extractive metallurgy using the system already developed. Published information sources have been identified and a thesaurus of terms is being compiled and tested. The software developed for CANMET's file-building operations has several features, including the selective dissemination of information and production from magnetic tape of photo ready copy for publication, as in a bi-monthly abstracts journal.

Jan 1, 1979

By J. H. Crocket, J. Andy Fyon

"All gold deposits within the Tisdale Group are spatially associated with carbonate alteration zones; however, not all carbonate alteration zones are host to gold mineralization.Within the komatiitic and magnesium tholeiitic volcanic rocks at the base of the Tisdale Group, discordant and stratabound carbonate alteration zones occur throughout. The alteration zones consist of a ferroan dolomite - quartz inner assemblage which is enveloped by calcite-quartz and an outer chlorite-rich subzone. Factors which control the distribution of carbonate alteration include joint systems, flow contacts, synvolcanic faults and bulk composition of the host rock.Two environments of carbonate alteration can be recognized: 1) The subsea-floor alteration zones developed within the volcanic rock succession where hydrothermal fluids did not discharge directly onto the sea floor. Insignificant gold production has come from this alteration environment. 2) Seafloor zones, which represent points of hydrothermal fluid discharge into the hydrosphere, are spatially associated with felsic volcanic rock complexes and are host to syngenetic, auriferous cherty dolomite.Carbonatized, magnesium tholeiitic basalts, which are host to the auriferous, cherty dolomite, are enriched in antimony (>0.35 ppm), boron (>30 ppm), gold (>5 ppb) and lithium (> 35 ppm), but are depleted in copper ( < 70 ppm), with respect to carbonatized basalts not associated with gold. Orerelated, altered komatiitic flows can be screened using gold (>5 ppb), lead(> 10 ppm), arsenic(> 70 ppm) and antimony (>1 ppm).The habit, petrographic characteristics and certain geochemical characteristics of the altered volcanic rocks suggest that the hydrothermal fluid was of sea-water origin."

Jan 1, 1982

By A. Zorkovská, S. Castro, P. Baláž, Z. Bujnáková

Enargite (Cu3AsS4) belongs among refractory copper minerals with very low hydrometallurgical extractability of copper. An application of enargite leaching in acid solutions leads to simultaneous dissolution of copper and arsenic and the final leach solutions have to be treated for the separation of both elements. However, the alkaline leaching of enargite is selective. Arsenic passes into leach while produced copper sulphide represents the raw material suitable for pyrometallurgy. The hydrometallurgical processing of mineral can be influenced positively by mechanochemical route. We have shown that more than 80 % of arsenic can be extracted from enargite concentrate by atmospheric alkaline leaching at 95 °C when mechanical activation in an attritor is applied. The produced Cu2S can be further treated with elemental iron where mechanochemical intervention is applied in the second stage of enargite processing. The final product forms Cu/FeS nanocomposite from which copper nanoparticles can be easily separated. The illustrated concept of copper obtaining from copper sulphide is an example of so-called “dry” processing, as reactions in gas and liquid phases are excluded. This concept of environmentally friendly metallurgical processing can be classified as an impetus for novel technology to produce copper from enargite concentrates.

Jan 1, 2012

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals.The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. It is shown here that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. However, the theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are unlikely to experience growth in crystal particle size through heterogeneous nucleation and are more likely to grow through aggregation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process."

Jan 1, 2016

By B. K. Mishra, Avijit Biswal, B. C. Tripathy, Abhijeet Singh, K. Sanjay, T. Subbaiah

We studied theeffect of anode substrates such as pure lead (Pb), lead antimony (Pb-Sb), and lead-silver (Pb-Ag) on the structural and electrochemical properties of electrolytic manganese dioxide (EMD). X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and chemical analyses were used to determine the structural and chemical characteristics of the EMD samples. The charge-discharge profile was studied in 9 M KOH using a galvanostatic charge-discharge unit. In all the substrates the current efficiencies were more than 99% except with Pb-Sb where it was 90%. Results revealed the nature of the substrate strongly affected the morphology of the deposited material which in turn affected the electrochemical properties of the EMD samples. XRD analyses revealed that the nature of the anode did not affect the crystal structure of the deposited EMD and all the samples were predominantly ?-MnO2, which is electrochemically active for energy storage applications. The EMD deposited on lead substrate showed superior discharge capacity of 245 mAhg-1 when compared with other substrates.

Jan 1, 2014

By M. J. Marinigh

Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable. In converting furnaces which have tuyeres such as the Noranda Reactor and the Teniente, Peirce Smith and Hoboken converters, efficient tuyere line management is critical to optimizing blowing rates, increasing refractory life, and improving safety. This paper will describe recent improvements made to equipment used for tuyere punching, tuyere silencing, tuyere pyrometry and refractory drilling of tuyeres and how the proper application of the equipment can lead to operational and safety improvements.

Jan 1, 2007

By C. Samson, R. S. Smith, S. W. Hefford

"Abstract - Time-domain electromagnetic systems are most sensitive to highly conductive targets during the transmitter on-time. Data collected during the on-time is highly influenced by the geometric relationship between the transmitter and the receiver. Unless corrections can be applied for these geometric variations, the ability to correctly detect and identify highly conductive targets can not be fully realized. Variables affecting the relative position between the transmitter and receiver include changes in the position of the receiver with respect to the transmitter, variations in transmitter attitude, and transmitter loop deformation. The level of accuracy in the determination of the relative geometry required to permit complete removal of the effects due to geometric variations is different for each of the variables and is dependent on the depth of the target. The most influential geometric variation involves changes in the relative position of the receiver with respect to the transmitter along the direction of flight; this variable, therefore, requires the highest degree of accuracy. The accuracy required for receiver motions along the vertical direction is roughly one order of magnitude less, and in the lateral direction, several orders of magnitude less. The objective of this paper is to relate the sensitivity of the response to transmitter-receiver geometry to the ability of an airborne, time-domain electromagnetic system to resolve a highly conductive vertical target. This is achieved by a detailed analysis of the effect of the individual x, y, and z distances between the transmitter and the receiver, the transmitter attitude (roll, pitch, and yaw), and transmitter deformation.Sommaire - Les systèmes électromagnétiques en domaine temporel sont particulièrement sensibles aux cibles à forte conductivité durant le temps d’excitation. Les données collectées durant l’émission du transmetteur sont fortement affectées par les relations géométriques entre le transmetteur et le récepteur. Si un facteur de correction n’est pas introduit pour tenir compte de ces variations géométriques, la capacité de ces systèmes à détecter et identifier correctement les cibles fortement conductrices ne peut pas être pleinement réalisée. Les facteurs affectant les positions relatives du transmetteur et du récepteur comprennent les changements de position du récepteur relativement au transmetteur, les changements d’altitude du transmetteur et la déformation de la boucle du transmetteur. Le degré de précision requis pour déterminer la configuration nécesaire pour compenser complètement l‘effet des changements géométriques est différent pour chacune des variables et dépend de la profondeur de la cible. Les changements géométriques qui ont le plus d’influence sont ceux qui font varier la position du récepteur relativement au transmetteur dans l’axe de la ligne de vol; c’est donc cette variable qu’il faut contrôler avec le plus de précision. La précision requise pour le suivi des mouvements du récepteur le long de l’axe vertical est moindre d’environ un ordre de grandeur, tandis que selon l’axe latéral elle est diminuée de plusieurs ordres de grandeur. Le but du présent article est d’établir comment la susceptibilité de la réponse à la géométrie transmetteur-récepteur affecte la capacité d’un système électromagnétique en domaine temporel aéroporté à reconnaître une cible verticale fortement conductrice. Cet objectif est atteint par l’analyse détaillée de l’effet individuel des distances x, y, et z entre le transmetteur et le récepteur, l’attitude du transmetteur (lacet, roulis, tangage) et la déformation du transmetteur."

Jan 1, 2006

By Norman R. Paterson

"Under certain conditions useful gravity information of a reconnaissance nature can be obtained with-out measuring elevations by spirit level surveys on the ground. Gravity surveys can become part of a practical exploration program where high cost and slow progress previously hindered their utility. The advantages of the new elevation procedures are realized mainly in remote areas, in areas where ground transportation is slow and difficult and on surveys where the station spacing is large in comparison with the distance of the average optimum level shot. To utilize the advantages, transportation by helicopter or light plane is usually necessary. Methods of obtaining elevation control without leveling include: barometric altimeter survey; photogram-metric -APR spot determinations; methods involving the measurement of gravity gradients. The accuracies of these methods have been tested and compared with the normal accuracy of level surveys. It is felt that each method has its place in reconnaissance gravity work, particularly in the open areas of Northern Canada."

Jan 1, 1960

By H. C. W. Bosman

"Over the past five years, contributions from geologists and mining engineers were instrumental in the successful development of MEPS. It is a system of FORTRAN programs specifically designed to be used by mining personnel to solve geological and mining problems. MEPS is a flexible keyword-driven system. Extensive error editing procedures significantly reduce the time required to proceed from problem recognition to solution. Possibly the most attractive feature of MEPS is that computer solutions may be guided or selectively modified to obtain desired solutions. Some highlights of MEPS are:1. Vocabulary that is familiar to mining people.2. Geological data storage and retrieval.3. Statistical analysis and variograms.4. Contour maps of assays and geological horizons.5. Trend surface analysis with residual evaluation.6. Ore reserve calculations.7. Open-pit mine design.8. Marginal profitability calculations on pit walls.9. Production scheduling.10. Vertical cross-section plots indicating pit outlines, ore grade contours and selected geological horizons."

Jan 1, 1973

By W. J. Pearson

"""POTASH"" is a term applied to the compounds of the element potassium (K) and when used in agriculture and industry is ex-pressed in terms of potassium oxide (K2O), regardless of the actual com-position of the compound. When a chemical analysis is made of a fertilizer, the amount of K is deter-mined and then calculated to the equivalent amount of K2O. However, the compound K2O does not exist in nature. Most of the world's potash supply is derived from mineral deposits similar to those in Saskatchewan and New Mexico. However, there is some production from concentrated surface brines such as occur in Searles Lake, California; Salduro Marsh, Utah; the Dead Sea; and from well brines in Micl1igan."

Jan 1, 1960

By D. Haraguchi, S. Izawa, C. Tokoro, S. Owada

"Arsenic is widely known as a toxic element for humans, animals and plants. Because of more stringent wastewater standards not only in Japan but also around the world, research for appropriate and efficient treatment method for arsenic is becoming increasingly important. Coprecipitation or adsorption process using ferrihydrite is widely implemented for dilute As(V) removal from wastewater. In this study, the sorption mechanism of dilute As(V) with ferrihydrite in coprecipitation or adsorption process was investigated. To accomplish this, we conducted batch experiments of coprecipitation or adsorption and compared these results for sorption isotherm and zeta potential. These experimental results showed that sorption mechanism in coprecipitation process depends on the initial As/Fe molar ratio; simple twodimensional adsorption onto the surface of ferrihydrite when the initial As/Fe molar ratio was < 0.4, and some three-dimensional uptake with ferrihydrite when it was = 0.4. We also evaluated the sorption mechanim by analysis of X-ray diffraction (XRD) and X-ray Absorption Fine Structure (XAFS). XRD or XAFS spectra showed that surface precipitation of amorphous ferric arsenate was formed when the initial as/Fe molar ratio was = 0.4, beyond the thermodynamic bulk precipitation range for ferric arsenate.INTRODUCTIONArsenic is toxic to animals, including humans, and long-term exposure to arsenic via drinkingwater causes cancer of the skin, lungs, urinary bladder, and kidneys, as well as other effects on the skin such as changes in pigmentation and thickening (Ghosha et al., 2008). Elevated levels of arsenic are often present in the environment as a result of the weathering and dissolution of minerals as well as in response to numerous anthropogenic sources including the discharge of mine wastes, coal fly ash and the use of pesticides that contain arsenic (Nriagu, 1994; Singh et al., 2007). Indeed, the potential for arsenic exposure affects many people, as evidenced by several million people in Bangladesh and India being at risk of exposure via drinking water obtained from contaminated groundwater sources (Ahmed, 2001).Acid mine drainage (AMD) containing arsenic is a global environmental problem (Dold, 2008; Liang and Thomson, 2008) that also affects Japan, which has many abandoned or closed mines that have been generating AMD for the last few decades (Masuda et al., 2008). Several such facilities in Japan produce AMD containing dilute concentrations of arsenic that exceed Japanese effluent standards (0.1 mg/dm3) (METI, 2006). For example, AMD from the abandoned Horobetsu sulfur mine, the largest AMD source in Japan, contains approximately 10 mg/dm3 arsenic."

Jan 1, 2012

By L. R. Bower

"This paper describes a highly versatile variable speed unit with a torque multiplication feature as a direct replacement for a fluid coupling .The unit is comprised of a modulating clutch with torque converter and lock-up options.The UCD does not start or stop the motor. This is carried out in the normal manner.The UCD continually monitors and rapidly regulates the output speed to the requirement of a set point demand from input signals or a pre-set program with full manual override.The pre-set program can include start and stop ramps, top speed and minimum speed regulation and also mid-speed set point with security for man-riding, etc. Speed variation is from zero to 100% on a constant duty basis.The input signals can be from any source, e.g. belt weigher. load profile bunker probes, mine monitoring system, etc.The UCD when fitted with a torque converter has a torque multiplication feature which automatically provides a starting torque up to two and a half times greater than the full load torque without exceeding the normal motor power levels.IntroductionIt is common practice in the mining industry to drive conveyors, whether they be belt or chain, through a transmission system incorporating a fluid coupling between the driving motor and gear-box .However, there are drawbacks and in an effort to attain a better degree of drive and control, two-speed motors - inverters cycle- converters - hydrostatic drives, etc ., have been introduced."

Jan 1, 1986

By Marc Symbaluk

Core Programs Current ? Aboriginal Involvement Program ? Adaptive Forest Management / Forest History Program ? Grizzly Bear Research Program ? Natural Disturbance Program ? Foothills Growth and Yield Association ? Foothills Stream Crossing Program ? Fish and Watershed Program ? Caribou Landscape Management Association ? Social Science Program ? Local Level Indicators Program ? Communications and Extension Program ? Geographic Information Systems Program ? Mountain Pine Beetle Ecology Program In Development ? Climate Change Program ? Forest Community Program ? Water, Quantity and Quality Program (Water for Life) ? Circumboreal Initiative ? Yellowhead Ecosystem Management Group

May 1, 2008