Search Documents

By I Brunton

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to MillTM optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions û compressive and tensile. In the first region, compressive stress waves form a æcrushed zoneÆ directly adjacent to the blast hole. The second region, termed the æcracked zoneÆ, occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to MillTM project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the fine to intermediate section (1 mm to 100 mm) of the fragmentation curve. This region of the distribution is important for Mine to MillTM optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split. Following this work, an improved fragmentation model will be developed in response to these findings.

Jan 1, 2001

By G W. Croft, L E. Krause

The current copper ore handling systems in use at Xstrata CopperÆs Mount Isa Copper Operations are up to 33 years old and have hoisted over 160 Mt at a rate of around 6 Mtpa. The mineÆs production profile is increasing in line with the optimum life of mine plan to over 6.6 Mtpa, which requires a system utilisation and reliability above that previously achieved. Copper ore is hoisted up the U62 shaft, which forms the central part of the U62 ore handling system. In theory this system can cope with the duty planned if the bottleneck is only the U62 winder. To achieve the planned production rate will require increased focus on reliability of each component in the ore handling system so that ore is available at the shaft for hoisting whenever the shaft is available, and the shaft is available for the maximum practical time. Increased availability will be achieved through the outcomes of the study of each component in the U62 system, and the internal ore handling systems that deliver ore from as far as 2 km laterally and 700 m vertically from the U62 shaft. The true capacity of each component is being determined and current performance is being measured with the aim of improving performance through root cause analysis and engineering out the causes of delays. The program began in March 2004 and this paper describes the progress achieved as of April 2005.

Jan 1, 2005

By R Loweth

The application of discreet event simulation has matured in modelling manufacturing systems for production analysis. This simulation tool was used in studying a number of mining operations, especially material handling processes. The study of truck-shovel operation including equipment matching, selection, and production estimation utilised the discrete event simulation for providing valuable decision-making information. The sophistication of the available simulation tools grew over times, and simulation driven animation was used to facilitate the validation and visualisation of the simulated system. This form of visualisation enhanced the simulation use greatly. First of all, it provided a communication medium to transfer information to the non-technical managerial personnel as a better decision-making tool. Moreover, the animated visualisation provided a validation tool to check the working of the simulated system and interaction among its components.

Jan 1, 2003

By Shining Z

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The rheological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

By G R. Ballantyne, M S. Powell, M Tiang

This paper reviews the proportion of energy attributable to comminution within the Australian gold and copper mining sector. The need for this is motivated by inconsistencies in the quoted energy usage data and the lack of a common basis for reporting the fraction of energy in mining that is attributable to comminution. This study should form a reliable basis from which to assess both demand and opportunities to reduce energy consumption.The proportion of milling energy was calculated for the major producers in the Australian gold and copper sector. A sampling methodology created by Powell et al (2003 - 2010) was initially used to provide an accurate and meaningful measure of the energy used in the comminution process. However, no useful method for grouping similar mines was found. Fortunately, a surprisingly large amount of high quality data was found from a number of different sources, allowing the development of robust relationships to be used to estimate a high proportion of the unknown values. The fraction of energy attributable to comminution was found to be dependent on how the total energy consumption was defined. For instance, comminution accounted for 52 per cent of the electrical energy, but only 21 per cent of the total energy publicly reported by the mines because a substantial proportion of energy used on a mine is in the form of transportation fuel (mostly diesel). Critically, the measured electrical energy consumption does not account for transmission and generation losses, while diesel energy usage is typically quoted according to its calorific value. This review proposes that diesel should instead be converted via the mechanical efficiency factor for diesel engines. Using this conversion, comminution was found to account for 36 per cent of the available energy on average. This approach allows a useful basis of comparison for mines regardless of whether milling energy is obtained from electrical or diesel generation. A summary of the results are shown in Figure 7 with other values obtained from literature. The total comminution energy assessed in this study accounts for 1.3 per cent of AustraliaÆs electricity consumption, this figure will increase as the other mineral commodities are added to the study.CITATION:Ballantyne, G R, Powell, M S and Tiang, M, 2012. Proportion of energy attributable to comminution, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 25-30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

By P Waters

BHP Billiton Iron Ore initiated a program in January 1995 at the Mt Whaleback operation in Newman, Western Australia to develop a closure plan for the overburden storage areas (OSA), which have the potential to generate acid rock drainage. The primary research program includes the development of technology for the long-term performance of OSAs with respect to slope stability, surface run-off, erosion, water infiltration and vegetation. The objective is to control acid rock drainage by preventing moisture movement into and through the OSA material. Infiltration to the underlying OSA material and closure costs are minimised due to the presence of the run-of-mine (ROM) cover material. A summary of the field data is presented to illustrate low percolation rates to the underlying OSA and key performance characteristics of the moisture store and release cover system design. Field data collected to date demonstrates that a moisture store and release cover system constructed with suitable ROM material has good potential as a final cover system at the Mt Whaleback site. The performance of the cover system on a sloped surface was significantly different as compared to placing the cover system on a horizontal surface.

Jan 1, 2003

By M A. Gontalves, A F. D C Varajpo

The Rio Capim kaolin district, located in the north-east of Parß State, Brazil, constitutes one of the worldÆs largest high-whiteness kaolin reserves for the paper coating industry. It contains, at the base of the main ore, a soft kaolin that gradually changes at the top into a ferruginous duricrust followed by a flint kaolin. The flint kaolin is completely discarded during the exploitation of the soft kaolin. With the view of a more complete beneficiation, aiming at a sustainable development of the minerals industry, the use of this residual flint kaolin has been considered for the manufacturing of zeolites. Zeolites were synthesised from the flint kaolin through a reaction between metakaolinite with soda at 80¦C, for durations of 24 to 144 hours. The transformation into metakaolinite was carried out at 800¦C and was not affected by the titanium oxides. For a synthesis time of only 24 hours, a zeolite 4A very close to its theoretical definition was obtained, whereas for synthesis times longer than 96 hours, a slight formation of hydro-sodalite was also observed. The synthesised zeolites were tested as cationic adsorbents on 0.5 molar solutions of Cu, Pb, Cd and Zn. The adsorption was measured for contact durations of one and three days. It was noted that the exchange kinetics were slow and that the retention was significantly greater after three days than after one day. The retention was greater than 50 per cent of the theoretical exchange capacity for Pb, Cd and Zn, which was different to Cu, where the retention exceeded its theoretical exchange capacity.

Jan 1, 2008

The paper describes the reasons for developing, specifically in South Africa, dense medium processes to allow baths to operate at low (about 1,35) and high (about 2,0) cut points. Low density processing was developed to meet the demand for low ash coals; high density processing was developed to enable heavily contaminated raw coals, destined to be burned in captive power stations, to be de-shaled without loss of combustibles. The anticipated and actual technical difficulties of operating baths at such density extremes are described, and the results from operating plants outlined.

Jan 1, 1987

By Tucker A. J

An overburden blast utilising horizontal blast holes was successfully attempted at the Ulan Coal Mines during December 1991. The blast reduced operational problems and costs and improved dragline productivity in an area of that contains poorly consolidated sands and clays overlying very hard Permian strata.The fan shaped shot consisted of seven 250 mm diameter holes between 80 and 95 metres long drilled into the highwall face. The holes were loaded with ICI Powergel Gold 25606 bulk Emulsion explosive. The design powder factor was 0.15 kg/bcm for the total shot of 180 000 bcros and 0.44 kg/bcm for the competent Permian strata into which the holes were drilled. Fragmentation from the horizontal blast was comparable to areas conventual blasted. Following the success of this shot further shots are planned for this area.

Jan 1, 1992

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

By G W. Wilson, P Ritchie, N A. Currey

The design and rehabilitation of potentially acid forming (PAF) waste rock dumps is site specific, being a function, among other factors, of the rock types, the dumping and storage method employed, and the climatic setting. The æstore and releaseÆ cover system developed to manage acid rock drainage (ARD) from mineralised waste rock dumps at Kidston Gold MinesÆ open pit operations in the semi-arid climate of North Queensland, Australia, has been monitored for seven years. The paper describes the philosophy behind the design of the PAF dump and æstore and releaseÆ cover system and the adaptation of the cover system over time to suit KidstonÆs conditions. The results of monitoring over the seven years since the first cover was constructed are presented, and the approach being taken at Kidston to ensure that the risk of impacts from any residual ARD is accommodated and to facilitate lease surrender are described. The Kidston story is a valuable case study of a successful approach to remediating an identified source of ARD in a semi-arid climate, which has actively engaged all Stakeholders.

Jan 1, 2003

By Ward S. C, Gardner J. H

In 1990, Alcoa of Australia Limited was elected to the Global 500 Roll of Honour of the United Nations Environment Program for the environmental management and rehabilitation of the bauxite mines in Western Australia. This award placed Alcoa in the international best practice category. The story of constant improvement spans more than 20 years from a 'trial and error' start to a strategically focussed and research driven program today. The main driving force has come from within the company, against a set of strong corporate values and a well publicised Vision based on 'excellence through quality'. Along the way public opinion, action group protests, increased legislative controls together with the professional competence of internal and external environmental resources have all played a part in arriving at the level of current environmental management and mine rehabilitation performance. There were numerous lessons learned here during the evolution and maintenance of best practice. These included: I . To work diligently in obtaining a vision or strategic intent on mine site rehabilitation and environmental management - don't be easily dissuaded.

Jan 1, 1995

By D Nourry

Optimising the blast is a major issue in the blasting business. It generally means acting on the blasting pattern (drilling, charging, detonating) in order to get a given æresultÆ. This result may either be related to economic reasons, such as the fragmentation influencing productivity, or technical reasons, for example vibrations and projections. Within the frame of the EEC funded Brite-Euram project entitled æBlast-ControlÆ, involving academic research and applied expertise, a general methodology was developed to approach such a problem and currently applied to the industrial partners of the project and final end-users of the generated results. These partners are the limestone ALZO quarry of the CALCINOR group in the north of Spain and the dolomite DMD (Dolomies-de-Marche-les-Dames) quarry of the LHOIST group in the east of Belgium. A first part of the project, over 18 months, was dedicated to establishing a clear relationship between productivity of operations from drilling to primary crushing and the fragmentation resulting from the blast. Extensive monitoring of blasting, production performance and fragmentation data was carried out and automatically collected into a database on both quarries. As expected, it appeared that excessive amounts of fines or boulders were substantially reducing productivity and thus profitability of the operation. Furthermore, an æoptimalÆ fragmentation was assessed for the quarries to run at the best (high throughput, low cost). The second and last part, for the remaining 18 months, was then dedicated to adapting the blasting practice in order to orientate the fragmentation towards a æbetterÆ one. A very common problem normally addressed by any consultant. Nevertheless, the target was not limited to solving the problem for these two quarries, but also to develop a generic method to address this blasting adaptation process and to implement it into a computerised tool. At this stage, it is then obvious that portability of the method and the system are major qualities to be looked for. This paper is aimed to present how this method was developed, how the system was implemented and how it was finally used.

Jan 1, 2001

By Bensley C. N

In June 1995, BHP announced that it would build a Hot Briquetted Iron (HBI) plant and associated beneficiation, materials handling and infrastructure facilities at Port Hedland, Western Australia. This plant, the first direct reduction plant in Australia, will convert beneficiated iron ore fines into metallic iron for briquetting into HBI. The reduction plant will be based on the FINMET fluid bed technology jointly developed by Fior de Venezuela and Voest-Alpine Industrienlagenbau. Electric Arc Furnace steelmakers in the Asia Pacific region will be the principal customers for the product. This paper presents an overview of the facilities to be constructed by the project as well as discussing some particular technology and design engineering issues associated with the project.

Jan 1, 1996

By Segnit ER, Jensen G

The decoppering of soft and hard leads was investigated by stirring in an open pot, using sulfur or sulfur plus pyrites, or sulfur plus pyrrhotite, as reagents. Lead samples taken during the process were analysed for copper. Dross samples were examined by optical micro- scope, SEM and XRD. Soft lead containing silver can be decoppered satisfactorily by stirring with 0.1% S at low temperatures - close to 330¦C. Soft lead, whether containing silver or not, can be decoppered satisfactorily at higher temperatures by stirring with 0.1% S plus 0.4% pyrites. Then CuFeS2, Cu5FeS4 and PbS are formed, instead of Cu2S, CuS and PbS when using S alone. Hard lead containing tin can be decoppered satisfactorily by stirring with 0.1% S at temperatures from 320-400¦C. When stirring with 0.1% S plus 0.4% pyrites, reversion of copper from dross to lead on prolonged stirring does not occur. Hard lead without tin can be decoppered with S plus pyrites better than with S alone, but the presence of antimony hinders the decoppering, which is less effective on lead with 5.5% Sb than with 2.3% Sb.

Jan 1, 1980

By Fermino R

Reduction of waste oxides from steel plant operations was investigated in a laboratory tube furnace at different temperatures and furnace atmospheres. The results have shown that the waste oxide pellets are reduced rapidly to very high degrees of metallization irrespective of the furnace atmosphere and that the reduction is simultaneously accompanied by significant low- ering of the original impurities. It is shown, for example, that treatment at 1000¦C for 30 min. can reduce the Zn content from 0.98% to 0.0065% and K and Na contents from 0.19% and 0.76% respectively, to less than 0.01%. However, pellet strength at 1000¦C was low but this, as shown in the paper, can be very significantly improved by treatment at 1250¦C. The results indicate that the reduction of the waste oxide pellets of this investigation proceeds almost certainly by a chain reaction mechanism and that this principle could be advantageously extended to the reduction of iron ores and other oxides in general.

Jan 1, 1984

By Juniper LA

ERM Consultants Pty Ltd was established in 1980 for the purpose of introducing a disciplined coal technology and power station planning service, to support Australia's efforts in establishing a major export steaming coal industry. At that time, major coal exploration programs were mounted on more than 50 potential export coal deposits with proven open-cut reserves to export 200 Mt/a of coal. The fact that Australia achieved an export trade of only 30 Mt/a, equivalent to the energy requirements for a population of around 5 million people, illustrates the very small achievement to date. The main reasons for this small export steaming coal growth have been: 1. Failure to convince potential overseas coal buyers of the benefits of coal-fired power generation, and the ability of proper power station design to overcome environmental problems, and achieve reliable operation and long life when burning Australian coals. 2. Failure to promote Australian power engineers to advise on the use of Australian coals, resulting in Northern Hemisphere power station experience dominating in market countries. 3. Failure of governments to draw on privately practising Australian power engineers and coal technologists in technical workshops, presentations and assistance to overseas countries, to ensure that personnel whose business it was to serve the follow-on needs of countries were readily available. The result of these failures has been that: 1. Only a fraction of prospective overseas coal-fired power projects have proceeded. 2. Australia has had no influence in the design of overseas power stations to ensure that potential customers would be confident that Australian coals could be reliably burnt in their boilers.

Jan 1, 1987

IA )W cli',hla cn1cnt fault 7011(-s 0 11Cn cOrnprise a nrc,II of inrcIIinkc(I faults, cvtcnqonal shear and In]rck cxtcnsir>nal vein- fractures. Hydrothermal mineralisation localised around such structures testifies to their importance as conduits for fluid flow. Mesh structures are most commonly developed in situations approximating bulk pure shear but predominantly simple shear meshes also occur. They appear to develop through the infiltration of pressurised fluids into a heterogeneous rock mass with varying material properties. In some circumstances, mesh formation appears to be a precursor to the development of major throughgoing faults. Mesh formation generally involves hydrofracturing (Pf> a3, at least locally) and the condition Pf - 63 to be maintained for the mesh to remain a high permeability conduit, requiring fluid overpressuring at other than shallow depths in extensional-transtensional regimes. The volumetric character of earthquake swarm activity appears to result from the passage of hydrothermal fluids through mesh structures, representing a form of distributed fault-valve action along suprahydrostatic hydraulic gradients arising from magmatic intrusion, compaction overpressuring, metamorphic dewatering, etc.

Jan 1, 1995

By Dunlop G. A, Cantrell R. A

The metallurgical and engineering requirements that form the basis for planning column flotation Pilot Plant testwork are reviewed. Pilot plant operating issues are discussed and a basis for the testwork program formulated. The application of the testwork results to engineering design and scale-up is briefly reviewed.

Jan 1, 1992