Search Documents

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are the most common steel-based ground reinforcement used in underground mines in Western Australia. As with any other steel-based product used in underground mines they are susceptible to corrosion, particularly under aggressive minewater and mineral conditions. Because of their thin-wall tubular construction and large surface area, the potential damage resulting from corrosion is considered to be more severe for this type of reinforcement than for other forms of reinforcement made of solid steel bars. Because of the obvious safety problems which may result from corrosion, both mine operators and regulators have raised concerns regarding the long-term effectiveness of FRS installed in underground mines in Western Australia. Although corrosion has been recognised as an important safety issue, the controls of corrosion in varied underground mining environments has not been well understood. To improve the understanding of the corrosion behaviour of FRS, the Department of Minerals and Energy has initiated a research project focused on the mechanisms and extent of corrosion attacks, and their influence on the effectiveness of the reinforcement. This paper describes the research project and presents the interim results achieved To-date.

Jan 1, 1995

Shear-flocculation is one of a munber of potential processes for upgrading deposits of finely-grained minerals and, more generally, for separating different types of particles suspended in a fluid.The smaller the particle the more likely it is to follow the fluid streamlines, or be entrained within turbulent eddies, and the less likely it is to deviate from the streamline and attach to bubbles (froth flotation), other particles (selective flocculation) or magnetic poles (wet magnetic separation). As shown in Figure I, a number of ingenious ideas have been proposed to overcome this effect. The suspended particles are assumed to be 1 - 10 µm.Thus, the efficiency of attaching ultrafme particles of the valuable component (solid circles) to air bubbles, as in process A, is poor. The efficiency may be improved by attaching the particles to oil droplets (Ralston, Kart and Newcombe, 1984) to form agglomerates that rise or sink (B), to magnetic particles (C) (Parsonage, 1988) to allow recovery in a magnetic separator (D), to other particles to form aggregates (E) that are then either attached to bubbles (F) or recovered by sedimentation (G) (Warren, 1992), and to pieces of polyethylene (Rubio and Baltar, 1991) that rise or sink (H).In A, C, E, F and H, the forces that are generally used to ensure collisions result in adhesion are hydrophobic forces, hydrodynamic forces and inertial forces (Warren, 1992). These drag particles from the streamlines to allow particle-particle adhesion. In B and E, soluble polymeric molecules have been added to bridge between particles as they approach closely during a collision.The second major consideration is selectivity. Selective adsorption of the hydrophobe or polymer onto the valuable particles is the key. Many subtle effects of surface chemistry are involved in obtaining adequate selectivity. A complication in real systems is that the initial suspension is often naturally coagulated and needs to be dispersed before being selectively flocculated.

Jan 1, 1993

By R Farnf, M Pegden, S Hosein, T White

A number of theoretical papers have been published outlining the use of electronic detonators to limit peak particle vibrations levels, but few empirical studies have been undertaken and even fewer examples have been published of the use of such technology in the aggregates industry. This paper gives a summary of the research work carried out at two limestone quarries in the North of England, where a series of blasts were used to compare and contrast the use of electronic and non-electric detonators. The majority of blasts were carried out using the same burden, spacing and decked charge weight loadings. A methodology was established that could be used to reduce the peak particle velocities (PPVs) at two or more specific locations by using single-hole blast vibration signatures in conjunction with specific electronic detonator timing intervals. The initial study concluded that this was only possible if single-hole signature blasts were periodically recorded to establish the shape of the correct vibration envelopes as properties were approached. These wave envelopes could then be used as the basis for choosing the specific electronic detonator timing intervals to give the lowest PPV for the properties or locations concerned. This methodology was then used in the second study to access a large volume of aggregates adjacent to a working railway tunnel. The financial benefit for the company was to convert these additional tonnages of rock from being a resource to an exploitable reserve. The project involved careful blast design and the instrumentation of a number of boreholes to enable the results of blast monitoring exercises to be compared with predicted PPV results. The iterative process involved the vibration results being uploaded into æBlast LogÆ (an expert blasting database system developed by the Blasting and Environmental Research Group at the University of Leeds) and analysed to produce predictions ready for the next blast.

Jan 1, 2007

By T C. Souza Pinto, M Safari, F S. Hoseinian, D Deglon, L Leal Filhoc

In this study, the effect of hydrodynamic parameters on the iron ore reverse was investigated in a mechanical flotation cell. The work carries out using the case study of Iron ore from Vale in Brazil. The influence of hydrodynamic factors such as froth height, impeller speed, superficial gas velocity and solids percentage were evaluated on the quartz flotation. The results showed that the hydrodynamic conditions have a great effect on the flotation performance, especially on the fine and coarse quartz. The size-by-size analysis of the froth products showed that froth height, impeller speed, superficial gas velocity and solids percentage have a significant effect on true flotation quartz particles. The increase in the froth height decreased the recovery of quartz particles. The increase in the impeller speed increases the recovery of quartz particles to an optimum. The increase in the superficial gas velocity improved the flotation of coarse quartz particles. The increase in the solids percentage increases the recovery of quartz particles.

Sep 18, 2023

By Will D. P

A 328 m, 2.4 m diameter raise-bored shaft has been equipped with a modular ladderway system to provide a second means of egress from Aberfoyle's Hellyer Mine in Tasmania. The modular ladderway consists of platforms, ladders and service pipes assembled at the surface and progressively lowered down the shaft. This system provides a rapid, safe and economical non-entry approach to equipping a shaft. The modular construction and single suspension allows for future extension or for reuse in another shaft.

Jan 1, 1988

By Henderson N, Schaap H

In large companies with mining operations spread over multiple sites, it is essential that consistency between sites is maintained in preparing and classifying resource and reserve estimates. The endorsement by The AusLMM and AMIC of the "Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves" and the subsequent incorporation of reference to the code into the ASX listing rules for mining companies has provided a basis for the consistent classification of resources and reserves. However, compliance with other criteria more or less stringent than the Australasian Code can present some reporting difficulties. Examples include listing requirements for foreign stock exchanges, particular Acts of Parliament that may apply to individual leases, constraints imposed by individual companies on their own leases, and ultimately, reserves for short, medium and long term planning. Confusion can arise when any two or more sets of reserves for the same lease are compared.. To alleviate this confusion, a standardised procedure was developed for the calculation and classification of coal resources and reserves. The procedure which is geostatistically based incorporates a technique called "Irregular Block Kriging" where specific mining blocks are directly kriged. The procedure has enabled those engineers and geologists with only a basic understanding of geostatistics to apply the technique and not feel hampered by some of the complex mathematics which in the past has tended to inhibit and overcomplicate the use of geostatistics. The procedure has resulted in "cleaner" data bases and hence more reliable reserve estimates.

Jan 1, 1990

Magnetic Separators have a wide application in dry separation processes, frequently in conjunction with High Tension Separation. Dry processes can frequently be superior to established processes in more commonplace mineral associations. A system of dynamics is postulated and the forces operating ar'e examined, together with a method of evaluating the effect of operating variables. Practical applications of these theories to obtain optimum results on an individual separator, and various separations using a laboratoryroll type separator are described.Practical Flowsheets are of two main types, the first consisting of a series of scalping operations, the second for rougher, cleaner, and scavenger operations with middling recirculation. Some common separation problems with certain mineral associations illustrate the need for different approaches for different mineral associations. A table of mineral separation characteristics is appended, from which amenability may be tentatively estimated.INTRODUCTIONMagnetic separators are widely used, either alone or in conjunction with other wet and dry concentration devices, for the upgrading of a variety of minerals. The high standards of efficiency attainable in dry mills, together with reduced operating and labour costs, are slowly becoming apparent in a wide variety of plants. The combination of wet and dry concentration plant familiar in beach sand mining is finding application for such processes as upgrading a crushed chromite product, and production of clean scheelite,cassiterite, and other concentrates. Other dry beneficiation processes (such as the high tension beneficiation of iron ore, and the benefiGiation of asbestos) avoid the use of wet processes completely.Dry separation processes are likely to be applied more widely as their possibilities become more generally known.

Jan 1, 1958

Whilst decisions to commit projects have traditionally been heavily influenced by hurdle rates for d.c.f. analysis, it is suggested that evaluation of competitors' costs may be a desirable additional tool.The MICAS system developed over the past four years is described. This computer system uses standard costs modified by District and Mine factors to allow estimation of individual mine costs. The data base contains more than 15,000 items of data and more than 6000 costs are calculated.Recent applications include use for competitive analysis, predictive analysis, statistical analysis, and comparative assessments with scopes ranging from a few mines to the whole Australian export industry. Some areas where care is necessary are outlined and potential further uses are discussed.

Jan 1, 1985

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008

After the minim operation, most raw materials that occur in the earth's crust require some form of processing or refining before they can be converted into a final end product. In the mineral industry these remarks apply to materials such as iron ore, bauxite, limestone, copper ore and many others that are found in Australia in large quantities. Processing plants for these raw materials operate more efficiently, however, if the feed to them is consistent in both physical and chemical characteristics. Such uniformity rarely occurs in nature so that some form of homogenisation, or blending, is required ahead of the processing plant. Bending also assists the mining operation itself by reducing; the need for selective mining and, by combining high and low grade materials, a more uniformly graded, commercially acceptable product can be obtained, thereby increasing the commercial life of a mine or quarry. Bed blending is the most efficient of the processes available, and following its development in the United States in 1905, over 100 plants have been installed, or are under construction, all over the world. The original process, the Robins--Nessiter system, has been the subject of continued improvements and refinements, so that economical capacities are possible from less than 100 l.t.p.h. up to 10,000 l.t.p,h. and beyond.

Jan 1, 1969

By R Williams, P Godwin

In a time of changing rainfall patterns and in the light of recent tailings dam failures, there is closer environmental scrutiny for proposed tailings dam construction or expansion. Therefore the elimination of the traditional tailings dam could provide both environmental and cost benefits to an operation. One method to dewater tails is using pressure filtration to achieve lower moistures than what is currently available using other dewatering technologies. Further benefits include a higher rate of filtrate recovery, reuse of waste material and the potential for dry stacking of the filtered tailings cake, thereby minimising both risk and cost. This paper chronicles the replacement of two existing belt filter presses with a single McLanahan recessed plate filter press to dewater a tailings stream at a Bacchus Marsh site. It covers the slurry testing, equipment selection, installation, commissioning and operation of the filter press to achieve the following objectives:• removing the current tailings dam and slimes cells from the existing process to minimise failure risk and reduce the cost of a dam upgrade, as well as operational and maintenance costs• free up the surface area which was previously occupied by tailings dams and slimes cells• recover additional water to be returned to the process• reduce flocculent usage• reduce truck movements and handling.The project’s owner also expects to reduce carbon emissions by over 3000 t over the lifetime of operation as well as substantially reducing operating expenditure. By recognising the carbon reduction benefits, the project owner was able to successfully achieve partial funding through the Voluntary Waste Industry Protocol.An unanticipated, but as yet unquantifiable, bonus for the project was to seek an offtake agreement for the tailings thereby allowing the tailings to be considered a valuable source of beneficiated clay suitable for the construction industry.CITATION:Godwin, P and Williams, R, 2017. Pressure filtered tailings – environmental and cost benefits, in Proceedings MetPlant 2017, pp 324–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

A numerical model of the spontaneous combustion of coal has been developed and is being used to investigate the nature of self-heating in underground coal mines. Results to date confirm the complexity of the self-heating reaction in coal and illustrate the impact of the factors such as the coal reactivity, mass and airflow through the coal pile. Subtle differences in the chemical, physical and environmental conditions and make a significant difference in the development of a high temperature self-heating or a low temperature benign condition, the subtlety escaping normal underground observations. Additional work is planned to investigate the thresholds for such factors in the development of spontaneous combustion and it the implications for detection by gaseous Products.

Jan 1, 1998

The paper is aimed at mining engineers and other mining practitioners in the metalliferous mining industry who are considering the use of roadheaders and wish to understand the basic geomechanical and operational principles controlling their performance. The paper aims to address metalliferous minersÆ general unfamiliarity with roadheader technology, which is one of the factors which has limited the application of these machines in such mines. The historical development of drag tool mechanical excavation machines is briefly discussed, and factors affecting the application of roadheaders are mentioned. The mechanics of cutting with drag tools is then reviewed as are the effects of these and tool wear on tool performance. The implications of tool performance to roadheader performance are mentioned, the potential benefits of high pressure waterjet assistance are discussed and the relative performances of different tool types and materials are compared. Roadheader performance factors including productivity and utilisation are mentioned, and the state-of-the-art of conventional roadheaders is discussed in the context of machine weight, power and cutting head configuration. The influence of these and rock strength on machine productivity is analysed. Alternative, developing technologies are discussed which may extend the effective use of mechanical excavation into stronger rock masses which are beyond the range of conventional roadheaders. Finally, conclusions on these discussions are presented, along with recommendations for continuing research and development.

Jan 1, 1997

The purpose of the Lower Lea Valley Cable Tunnel project is to relocate the overhead power lines circuits, which currently cross the proposed site for the 2012 London Olympics in East London. This was the first contract to be awarded as an Olympic project and is on the critical path for the proposed Olympic Park as the construction of the Olympic village, stadium and other venues cannot begin until the tunnels are complete, the cables installed and the overhead power lines removed. The tunnelling works for the scheme include two parallel tunnels between Hackney and West Ham. Each tunnel is approximately 6 km in length. One tunnel is 4.15 m ID and connects the National Grid substations. The other is 2.82 m ID and connects the EDF Energy substations. The tunnels were constructed through mixed ground using four earth pressure balance tunnel boring machines. These were driven simultaneously from two drive shafts within a single site. The 12 km of main tunnels were constructed within a year from start to finish, with completion in June 2007. The shafts range between 6 m and 15 m ID. These were constructed using a combination of caisson sinking and underpinning techniques. Dewatering was adopted to suit the groundwater conditions.Other works include the design and construction of the head house buildings, cable and ventilation culverts, mechanical and electrical (M&E) installations and all associated works. In addition to the above, a further 1 km of tunnel and two shafts were added to the project scope connecting the EDF Energy tunnel to the substation at Bow. These additional works provided further challenges to the project to ensure that these works were constructed within the program constraints for the 2012 London Olympics. This involved refurbishing one of the tunnel boring machines from the main EDF Energy tunnel drives and relaunching the machine to construct the Bow tunnel. The Bow tunnel was constructed within two and a half months, with the tunnel boring machine breaking through in August, ahead of schedule. The main challenge presented by this project is the program constraints. This project outlines the requirement for team work between the client, stakeholders, contractor and designer in order to provide program certainty. A close working relationship between the contractor and the designer is required to provide value engineered, time-saving solutions to mitigate the risks associated with the design and construction program.

Jan 1, 2008

The mining and resources industry in general has relied on macro separation technologies (greater than 1 micron) through processes which include: ò sedimentation ò flocculation and coagulation screening and filtration ò absorption ò magnetic separation ò chemical leaching and precipitation Essentially, these processes and technologies provide the industry with an effective arsenal to handle most separation requirements to date. Dewatering of solutions is one of the most significant requirements of the resources industry, as practically all mining endeavours use water in their process for leaching, extraction, cooling, dilution or for potable drinking water.

Jan 1, 1989

By Higuchi K

For the mechanisation or automation of mining, recognition of the shape of mined cavities is basic information. A three dimensional shape measuring system, developed and tested, includes an ultrasonic range finder which is attached to the tip of a serial link manipulator. The range finder can be moved to any position and direction in the operational space of the manipulator. The position of a point on the surface of the object is obtained from the position of the range finder, the direction of the beam of the ultrasonic waves and the measuring distance of the range finder.To avoid collision between the sensor and the object, the manipulator is controlled to trace the surface of the object For the tracing control, another ultrasonic range finder is employed. The test results show that the developed system has high performance.

Jan 1, 1991

Broken Hill South Limited's discovery of phosphate deposits in the northwest of Queensland in 1966 prompted intensive exploration which has proved phosphate rock in excess of 2,000 million tons at ten separate deposits. Systematic exploration for phosphate in Australia was initiated by the Company in 1964. Early in 1966, an investigation of oil wells in the Georgina Basin in the Northern Territory and Queensland revealed widespread anomalous phosphate in early Middle Cambrian Beetle Creek Formation and Thorntonia Lime- stone. Phosphorites recognised in oil wells in the southeastern part of the Basin, Queensland, led to the discovery of the Duchess deposits, Exploration of the Beetle Creek Formation since 1966 has disclosed nine other sizeable deposits north of Duchess around the eastern margin of the Basin. The Lady Annie and the adjoining Lady Jane deposits, by reason of their location, 160 miles south of the Gulf of Carpentaria, are expected to be the first to be brought into production. Beneficiation testing and engineering investigations commenced in 1967. Transport between the deposits and various port sites in the Gulf of Carpentaria has been extensively studied and a slurry pipeline as a means of transport to a deep water island port, is now being investigated.

Jan 1, 1971

By T C. McCuaig, D B. Mapleson

The Wannaway Deposit is a structurally modified komatiite-hosted nickel-sulfide deposit. Until recently, nickel sulfide accumulations surrounding the Widgiemooltha Dome had been studied with a focus on understanding volcanological aspects of komatiite flow regimes and nickel-sulfide accumulation. Although volcanological features can be observed at Wannaway they are overprinted by several generations of structures associated with multi-phase deformation of the Dome. On the mine scale, two significant deformational events can be distinguished that control ore distribution. The first deformational event is represented by the formation of a layer parallel foliation within the footwall metabasalt and boudinaging of the ore into two distinct orebodies (mega boudins) during a north-south compressional event. Evidence of a second compressional event (east-northeast-south-southwest) is defined by reverse > dextral thrust-folding of the ore zone. The latter deformational event focussed the sulfide ore into thrust front positions where folded ore sequences are mined with stope widths up to nine metres wide. Later stage compressional and extensional deformation phases are observed but have minor, localised effects on the geometry of the ore zone. Four orders of control on the geometry and distribution of ore are interpreted through a combination of primary and secondary features observed at Wannaway. Extending the structural aspects of the secondary overprint features into areas of potential mineralisation has not only defined targets for extensions to the Wannaway Deposit, but has also aided to delineate high grade mineralisation and aid mining decisions. Obtaining an understanding of the volcanological conditions of formation, and more importantly, the structural evolution of the Wannaway region has been an integral part in optimising production.

Jan 1, 2003

By McPherson M. J

This paper describes a major ventilation study for the expansion of the El Teniente mine operated by Codelco, Chile. El Teniente is one of the world's largest under- ground mines. The design effort was under- taken in three stages and involved a partial mine ventilation survey with network simula- tion, detailed stope ventilation investiga- tions, and design of the entire mine ventila- tion circuit based on production plans to achieve 112,000 tons per day by 1995. The partial ventilation survey provided values of representative friction factors and resistances for typical ventilation raises and airways. These values were used to conduct detailed modeling of the block caving levels to investigate the most cost effective and practical means of providing the required ventilation. The results of these analyses were extrapolated to the proposed expanded mechanized zones.

Jan 1, 1988

By G Senanayake, J Andreazza

The general experience in gold cyanidation research activities and plant practice is that high oxygen and cyanide concentrations improve gold leaching kinetics which in turn reduce residence time and increase throughput. This paper shows how the improved pre-oxidation method for the pyrrhotite rich gold ore of Bounty Gold Mine has increased gold recoveries at lower reagent consumption rates. The installation of a pipe reactor, in conjunction with a Multi Mix Systems oxygen injector, has lowered the amount of oxygen required to achieve a dissolved oxygen level target of 20 mg/L. The improvement of the pre-oxidation stage and lead nitrate solution addition has led to a reduction in the free cyanide concentration required for leaching, resulting in a decrease in cyanide consumption rate by 36 per cent to achieve a one to two per cent improvement in the gold recovery.

Jan 1, 2002