Search Documents

By A Havenga, F, J Hough, R Grobbelaar

After the closure of mines they naturally start to fill up with water. As a result, hydraulic gradients develop between adjacent mines and different hydraulic water pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The geometry of the collieries in the central Witbank Coalfield make intermine flow possible in several areas. Since the Department of Water Affairs and Forestry declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon has been undertaken. The importance of the quantification lies in the DepartmentÆs goal of sustainable water management, and the possible long-term financial implications these flows could have for individual mines. The challenges of determining intermine flow are numerous, and attention is focused on the identification of areas where these flows can take place. Detailed mining plans on a regional scale are required, and detailed coal-seam floor data are combined to provide targets for possible interaction between these mines. The quantification of these flows is problematic due to the uncertainties regarding geometrical configurations and the variation in site-specific hydraulic characteristics of the coal and overlying lithilogical layers. To this end, use has been made of several analytic solutions and numerical flow modelling. Stage curves (volume versus elevation curves) for the opencast and underground workings have been calculated and first-order estimates for intermine flow or decant from these areas have been determined. The numerical modelling methodology entailed a down-scaling approach, starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines and finally looking in detail at the major areas of interaction. By considering different scenarios within the context of these flows, possible management options for intermine flow can be evaluated in terms of volumes and qualities that might emanate in the post-closure phases. Challenges for the future include obtaining site-specific information on the groundwater hydraulics and acceptable ranges for model parameters, and verifying model results over time.

Jan 1, 2003

By S Pigram, G J. Jameson

This paper is concerned with the tracking of particles in the froth phase of an aerated water/glycerol mixture. Experiments have been carried out in a specially designed laboratory flotation cell that allows formation of a deep froth. Phosphorescent tracer particles of various sizes were injected into the centre of a froth column where they were excited by ultraviolet lights, positioned at the back and front of the column. The motion of particles was captured on a digital camera with a green filter. The images from the digital camera were then transferred to a computer and an image analysis program was used to convert the colour intensity to the concentration of particles at each location within the froth. The tracer technique was used to determine the dispersion of hydrophilic particles and the variation of the concentration of solids with axial and radial positions.

Jan 1, 2005

By O Dahl, I M. Platten, E J. Sides

Many narrow-vein gold deposits are characterised by a high to extreme nugget effect and the presence of coarse gold. They rank amongst the most difficult of deposits to produce an accurate and precise resource estimate. This contribution presents a case study from the Nalunaq Gold Mine in Southern Greenland. The mine commenced operation in May 2004 and is currently operating at a rate of 400 tonnes per day, to produce about 100 000 oz gold per annum from a total resource base of 1.2 Moz. Mineralisation is characterised by quartz veins that are hosted within a shear zone that is continuous over about 1000 m. The principal orebody is the Main Vein structure, which ranges up to 3 m in width, maintains an average dip of 35¦SE, and contains significant gold grades (1000s g/t Au). Gold particles are often visible, with 25 per cent being greater than 250 microns in size. Variography using underground development samples indicates a nugget effect of about 75 per cent. For the 2005 resource estimate, a 2D metal accumulation ordinary kriged block model was used to produce a global grade for the Target and South Blocks of the Main Vein. Grade control chip-channel samples are collected from æshantyÆ drive footwalls, and used as the basis for both the kriged block model and to determine the grade of individual stope blocks by peripheral weighted averages. Geology plays a key role in mining efficiency, given the locally variable nature of the ore zone.

Jan 1, 2006

By Mutmansky J. M, Organiscak J, Qin J, Bhaskar R

The results of a two-year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the analysis results and conclusions of the study are discussed.

Jan 1, 1988

Mining is a high risk, high capital and potentially high reward undertaking. A large proportion of the risk comes from a lack of definition of the orebody (which also provides some of the potential) and the unpredictable nature of the market. This makes the planning process difficult but encourages the development of a robust yet flexible mining system. The system should be capable of absorbing some deviation from the anticipated concept without a significant impact on profitability. The mine planning process tends to consist of a series of related but discrete stages. For instance, the pit shells are designed, a schedule for the pit shells is created, a plant fleet is chosen to achieve the schedule and a financial analysis is carried out on that scenario. It is likely a few iterations are carried out using various mill throughputs to produce a favoured financial result. The problem is that handing results from stage æBÆ for use in æCÆ doesnÆt encourage a flexible system. æCÆ is likely to be built for exactly æBÆ. Unfortunately, in mining, æAÆ (the orebody) has the highest potential for variability and impacts everything else downstream. æDÆ the market also has high potential for unplanned variability. These variations can spread and æreverberateÆ through the whole mine process. For example an unexpected increase in ore oversize impacts all downstream mine processes to the primary crusher which may in turn create problems back æupstreamÆ by restricting throughput rate. Also an unexpected drop in demand or price could require modifications to the planned production rates. This paper looks at how mining process simulation can be used to support the development of strategies to counteract unforseen circumstances or alter production to match fluctuations in demand and price.

Jan 1, 2003

By V Ser, I Smit, C Robertson

Anglo American has been researching the potential benefits of inter-particle comminution techniques for several years. Inter-particle comminution has additional benefits in terms of milling circuit performance such as energy consumption and stability. This paper focuses on the flotation benefits. Inter-particle comminution leads to selective breakage, mineralogical analysis has shown that this leads to improved liberation of the valuable minerals. In addition to selective breakage, the relatively short residence time experienced in typical inter-particle comminution machines allows more efficient classification which contributes to a æsharperÆ product size distribution. The effect of particle size in flotation has been well documented in literature. In general, it is has been shown that there is an optimal particle size range for flotation, and that both above and below this range, flotation recovery is adversely affected. Results show that the narrow size distribution which results from inter-particle comminution improves flotation recovery. Furthermore, the absence of excessive fine gangue material which typically results from conventional fine (-75 ¦m) milling of talcaceous ores, can lead to 100 per cent savings in depressant consumption when such ores are subjected to inter-particle comminution. To-date, this technology has been evaluated on more than ten ores. This paper will focus on one set of results which demonstrates a number of common differences that exist between material that has been milled conventionally and using inter-particle comminution technologies, with emphasis on what the impact of these differences is on flotation performance. A pilot scale (200 kg/h) vertical roller mill (VRM) was used to produce the material, and the results shown will describe conventional laboratory batch, locked cycle and pilot plant flotation testwork.

Jan 1, 2005

The current quantity of rejects from coal beneficiation in Australia represents 20 to 25% of raw black coal production. Approximately 80% of the rejects are derived from coarse processing for particles in the 200mm to 0.5mm size range. The safe and enviornmentally acceptable storage of coarse coal rejects is of interest to coal mining companies. Additional public benefit would be derived from the utilisation of a waste product as a source of fill material for civil and mining engineering applications. BHP Engineering has taken a leading role in the design for storage and utilisation of coarse rejects from two mines associated with the Broken Hill Proprietary Conipany Ltd. The tailings dam at Stockton Borehole Colliery (N.S.W.) is to be raised and a study by BHP Engineering has shown that coarse rejects are suitable for the formation of the supporting embankment surrounding a compacted clay core. Transportation and storage of coarse rejects at the Thiess Dampier Mitsui Riverside Mine (Moranbah, Qld) is achieved by a conveyor leading directly from the coal preparation plant to a discharge stacker on the crest of the rejects stockpile. Production of coarse rejects was higher than anticipated for the initial dump design. BHP Engineering has completed a review of dump design with emphasis on safe operating conditions for the conveyors and stacker system. Data on the geotechnical properties of coarse rejects from Australian coal mines are presented. Coarse coal rejects are a material which should not be considered as waste, but as a potentially valuable resource for many future applications. Appropriate engineering design for the storage and utilisation of coarse rejects would result in an improved environment and economic benefits for the Community.

Jan 1, 1987

By J Moncrieff, P Bellairs

The Black Star Open Cut is located immediately adjacent to the township of Mt Isa and is situated in the middle of extensive pre-existing infrastructure including two concentrators, two smelters, a wet fill plant and two shafts. At any one time there are in excess of 500 people working on the surface within an industry-accepted 600 m exclusion zone from Black Star blasts. Apart from the surface operations there are also the underground operations including the lead mine (closed in December 2005) and the Enterprise and X-41 mines that must clear for all Black Star blasts. The application of industry standard blasting exclusion zones (600 m) was risk assessed as imposing operationally prohibitive constraints which could cause significant business interruption due to the logistical challenges required to ensure that all personnel from surface plants were evacuated for each blast and potential for lost production whilst these personnel were not operating the plant. In was therefore an imperative for the blast exclusion zone to be reduced. This was achieved by the: use of a QA/QC team to ensure that relevant drill and blast implementation is within an acceptable tolerance (KPIs) from design; use of high-quality stemming material called HMR, which is a by- product of the concentrating process and is generally sized at -14 mm with very little fines; implementation of appropriate training and support to Black StarÆs own blast crews, reinforcing the need to achieve the designed amount of stemming in every hole; and provision of appropriate support from Black StarÆs management for additional resources to ensure that every blast achieves design within the KPIs but especially in high-risk areas. The blast exclusion zone was successfully reduced after monitoring the flyrock results from more than 176 blasts. Black Star Open Cut now maintains a minimum blast exclusion of 200 m in critical areas; however, general blasting currently uses a 250 m exclusion as this provides additional risk management whilst still minimising the logistics associated with clearing and securing the slightly increased area.

Jan 1, 2007

By Lynce AJ

A method has been developed for the prediction 'of 'the- . performance of a multi-stage grinding=cyclone classification circuit of any degree of complexity on any ore for a wide range `of operating conditions, The-.method involves ;the. s` inu ation b'f the circuit on a digital computer by means of. matheinatical' models ":bf the"' individual units:, the. development of which is- also discussed'., At present, in order to establish 'the!'" charac'teristtics of they ¦ore- and the machines. in mathematical terms;. it is necessary to know'the performance of a , simpl,.e. ; system on tri.e ore - for! one known ,,feed rate and.fe.ed s,l-zing, analysis. ' ,Fiiither work on :the- separate identification 'of the terms defining the characteristics of the ore and the machines may permit the method to be, applied directly to the cj.4ta,derived from small scale tests on ores,

Jan 1, 1964

By Marton A

The Readymix Group have a Quarry Improvement Program - 'Building in Quality (BIQ) which has many parallels to the ICI Explosives' total quality management - 'Quality Improvement Program' (QIP). Both companies have for some time recognised that the 'do it right first time' principle means less wasted effort and materials, that efficiency breeds profitability and so actively promote the quality culture. To install the principles and generate the culture requires considerable commitment and effort from the top down and invariably spreads to the suppliers and sub-contractors. Understanding the component processes involved with the quarry operation, analysis of those processes and gaining a breakdown of the cost of non conformance then allows the astute quarry operator to make the necessary changes to improve the process to realise profits. This paper outlines the steps in such a process and the profitable outcomes of the commitment to continuous improvement at the Nickol Bay Quarry.

Jan 1, 1994

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D Thomas, B Gallagher

Valuable data for geotechnical interpretation and integration into effective Australian underground mine planning may often be available, yet is not always fully appreciated or utilised, particularly in the early stages of mine planning or in due diligence studies. There may be considerable benefits associated with early prioritisation of geotechnical evaluation and impact on mine planning. Unidentified, misinterpreted, or ill-defined adverse geological and related geotechnical resource characteristics can pose significant business risk to underground coal projects and operations. Preliminary resource definition in the early conceptual mine planning stages attributes significant focus (entirely warranted) on resource quality and structural geology constraints. Yet detailed geotechnical data analysis and interpretation, which may have a substantial down stream impact and sensitivity with respect to future mine planning strategies, at times is given lower priority, or scoped and resourced in the later stages of a bankable feasibility study. Through extensive mine planning experience and observation of downstream process impacts, it has been found there is often data available for geotechnical analysis that does not readily stand out or is not adequately understood or utilised, available at the early (conceptual) stages of mine planning. Part of the issue may be that exploration geologists are not necessarily experienced geotechnical engineers and do not necessarily recognise or understand all important parameters. Subject to appropriate application of experienced professionals data can be manipulated to provide key geotechnical hazard assessment at minimal cost, and provide a framework for understanding and optimising the mine planning process. Although there is no single prescribed strategy for resource evaluation from a geotechnical perspective, potential business risks and mitigation approaches can and should be adopted at the conceptual mine planning stage. There has been a recent focus in the metals industry to provide a reporting framework for geotechnical classification of mining projects. This paper outlines the strategies and gives examples of key analyses adopted in mine planning and discusses the relative merits of adopting a reporting framework as a tool for geotechnical classification in mine planning.

Jan 1, 2005

By J Ralston, G B. N Kaggwa, L Huynh

Three polymers of varying chemistries and molecular weights have been used to depress talc in a model sulfide ore consisting of talc, pentlandite, and chalcopyrite. Flotation testing revealed a distinct hierarchy of effectiveness of the polymers in the depression of talc (HP Starch > Polymer-H > Dextrin WY) but a different order of effectiveness for depression selectivity (Dextrin WY > Polymer-H > HP Starch). Adsorption isotherm determinations for the gangue and valuable mineral phases indicate that the differences in selectivity are partially due to adsorbed amount variations, with Dextrin WY adsorbing marginally less on the sulfides than Polymer-H. Contact angle measurements on packed particle beds have revealed that the polymers have differing abilities to reduce the contact angle of talc and the sulfide minerals. An explanation of the observed trends is given in terms of the binding mechanisms of the polymers on the talc and the sulfide mineral phases. Order of addition effects between collector and depressant were also investigated using adsorption isotherm determinations for the polymers in the presence of a pre-adsorbed layer of collector and vice versa. Adsorption of the polymers was not affected by the presence of the collector. Similar results were obtained for the adsorption of collector in the presence of pre-adsorbed layers of polymer.

Jan 1, 2005

By B Dunstan, F Wirfiyata

PT Newmont Nusa Tenggara (PTNNT) operates the Batu Hijau copper and gold mine and process plant on the island of Sumbawa, Nusa Tenggara (Barat)  NTB, Indonesia. The plant consists of a nominal capacity 120 000 t/d conventional semi-autogenous ball milling crushing (SABC) circuit followed by sulfide flotation to produce a bulk copper concentrate for sale. Process control is effected by a plant wide distributed control system that overlays an extensive integrated programable logic controller (PLC) framework. The system is enhanced by a supervisory expert control system.Since plant commissioning in September 1999, over US$4 million has been expended as part of a systematic continuous improvement approach to optimise plant control performance. Works completed to date include: redesign and upgrade of architecture of the control system to ensure long-term system reliability, security and upgradeability and to provide a suitable platform for advanced control; integration of supervisory and advanced control tools, techniques and instrumentation; and implementation of sound network communication and plant data reporting tools. This paper outlines the evolution of process control and associated systems and tools that contribute to successful operation and ongoing performance optimisation at Batu Hijau.

Jan 1, 2009

By H Bartosiewi, M Kuruppu, F Mashiri

Wire ropes are one of the most heavily used components in a dragline. They are subjected to harsh conditions during the regular usage of a dragline in a mining operation. Hoist ropes are subjected to fatigue due to the cyclic nature of load handling as well as due to rope bending over the sheaves and the drum under load. This leads to wire breaks due to fatigue. Accumulation of a number of wire breaks close to each other can have a detrimental effect on the rope. Furthermore, to allow for the increasing demand for higher load capacity coupled with the inconvenience of having very large ropes, the factor of safety is often compromised, which increases the wear rate. Drag ropes are also subjected to heavy loads. More importantly, they are allowed to drag along the rough mine surface subjecting them to external physical abrasion. This makes the life of drag ropes one of the lowest among those used in a dragline. Suspension and IBS ropes are relatively uniformly loaded during their regular usage although they need to withstand dynamic load cycles as well as bending. Hence they tend to last for a number of years on average. The paper analyses the wear types and their severity of each of these rope applications, and suggests methods to determine rope wear rates and the resulting rope life. The paper further gives suggestions for good operating and maintenance practice that can extend the rope life and help reduce the large expenditure associated with every major rope change in a dragline.

Jan 1, 2005

By J Hadjigeorgiou

The stability of open stopes in underground hard rock mines is influenced by several factors including the shape and size of the excavation, surrounding stresses as well as the degree of jointing. This paper presents a design methodology for stope analysis in jointed rock masses. The proposed approach relies on geological structural data to construct realistic three-dimensional joint network models. The stability of an open stope is determined based on a limit equilibrium analysis.

Jan 1, 2000

Strata bolting/dowelling reinforcement techniques are being reintroduced into the mines of the National Coal Board. There are strong reasons for the selection of the full hole anchorage principle of bolting and for the development of the wood/resin dowel. There are strong reasons also for the measurement of strata bed separation as the method of assessing the effectiveness of a roof bolting system. There are several designs of bolts. Instruments have been developed for investigation and control purposes. Different drilling and bolting machines have been employed in trial sites. In addition comparative laboratory model work has been conducted on simple non-bolted and bolted systems.

Jan 1, 1971

By Rolfe PR, Ellis BA, Clements RJ

Associated Minerals Consolidated Limited (AMC) is constructing a 112,500 tonne/yr synthetic rutile plant at Narngulu, near Geraldton in Western Australia. Design of the plant is based on the technology developed by AMC and utilised in its two existing plants at Capel in Western Australia. Ilmenite Feedstock for the plant will be sourced from AMC's mine at Eneabba and coal obtained from the Collie deposits. The plant is scheduled to come on stream in the second quarter of calendar 1987. The rationale of the decision to construct the Narngulu plant is examined against the background of the world market for high-Ti02 content feedstocks. Also provided is a detailed description of the plant and an examination of the technology used in process Design.

Jan 1, 1986

By L McCarthy, B W. Cuffley, O K. Thomas an

The Central Victorian Goldfield is a world-class field located in Victoria, Australia. It is currently undergoing a revival through activities in the Bendigo, Ballarat, Tarnagulla, Maldon, Castlemaine and other fields. Sediment-hosted auriferous gold-quartz reefs that are structurally and geometrically complex dominate the region. To date, no remote methods have been developed to assist in the targeting of the discrete high-grade oreshoots that characterise the mineralisation. An understanding of the structural setting and controls, and thus likely frequency of repetition of oreshoots remains the main exploration tool. Gold within the reefs is generally characterised by both its coarse nature (>100 up to 10 000 microns) and erratic distribution; as a result, most of the Victorian deposits are classed as high- to extreme-nugget effect systems. This characteristic ensures that mineralisation is very challenging to explore, evaluate and exploit. The key issues facing the explorer and miner are related to effective sampling, and definition of geological and grade continuity, and ultimately grade and tonnage. Tonnage can often be estimated to a reasonable level of confidence, whereas the grade estimate generally carries a medium- to high-level of uncertainty. In these deposits, surface diamond drilling alone is generally only able to define an Inferred Mineral Resource, with underground development, closely spaced in-fill drilling and bulk sampling/trial mining required to define Ore Reserves. The extraction of gold from ores is relatively simple, based on the coarse nature and hence amenability to gravity recovery. Ground conditions and the need for in-stope grade control (eg mapping, sampling etc), generally point toward mechanised cut-and-fill as the primary stoping method in the region. To potential investors this style of mineralisation has been viewed as high risk, because of the associated low confidence in the grade estimate, general paucity of Ore Reserves at mining start-up and need for underground development at the Feasibility Stage.

Jan 1, 2004

By Revy T

A testwork program aimed to improve the assaying of underground face samples established that for an Accelerated Cyanidation Extraction using the LeachWELLTM 60X catalyst, followed by an Aqua Regia finish (to quantify non-cyanide-extractable gold): ò Assay results (including the aqua regia finish) from a full set of samples from one underground face can be returned within four hours. ò The reagent dose to make the method simple and 'bullet-proof' is 8 gm LeachWELLTM 60X and 20 gm NaCN per 200 gm sample (30 per cent solids). Pulverising is to 90 per cent passing 75 micron (compared to the standard of 90 per cent passing 150 micron), and cyanidation is completed within one hour - however both might be further optimised. ò The LeachWELLTM/Aqua Regia results demonstrate that Fire Assays suffer from a significant nugget effect which makes the Fire Assay data relatively unreliable. ò Original costs, specific to Bannockburn (viz including an Aqua Regia finish), handling approximately 20 000 to 25 000 per annum is estimated to be $5.40, ie about one-third less than fire assaying. Optimising is further reducing these costs. It is estimated that the LeachWELLT"'/Aqua Regia assay procedure has reduced the probable error limits of any given assay of this ore from the range 0.74x to 1.36x for Fire Assay, to an appreciably smaller range of 0.90x to 1.11x. Thus for a cut-off grade of 1.60 g Au/t, samples with Fire Assays ranging up to 2.18 g Au/t have 25 per cent chance of being below cut-off, while samples with Fire Assays as low as 1.18 g Au/t have an equal chance of actually exceeding cut-off grade. This 1 g Au/t range in uncertainty is generally unacceptable for many practicalgrade/tonnage relationships. By contrast, using LeachWELLTM + Aqua Regia assays, the estimated corresponding limits are 1.44 g Au/t and 1.78 g Auk respectively - a far more tolerable 0.34 g Au/t range of uncertainty. Subsequent data has demonstrated that sufficient accuracy for grade control is achieved by Accelerated Cyanidation alone, further halving the cost of assays.

Jan 1, 1994