Search Documents

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A Williamson

The New South Wales Department of Mineral Resources objective is to use data and information to undertake a detailed analysis of incidents and accidents to identify risks so that the predictable can be foreseen and avoided. The Department of Mineral Resources has established a computerised database called COMET (COmmon Mines EnvironmenT) to capture information on accidents incidents, inspections, audits and accreditation in improving safety and environment performance. This data together with data from Coal Mines Insurance and WorkCover NSW is being used to provide trend and comparison information. The NSW Injury Risk Management Research Centre at the University of NSW has been engaged by the Department to collate and prepare a detailed analysis of the data. Through this process, five areas have been identified for further research. These being: electrical energy, mechanical equipment, work environment, hours of work, and contractors involvement accident and incidents. The paper covers: the establishment of a mix of performance measures for the industry to indicate whether the safety performance is improving; the provision of data to provide useful comparisons and benchmarks against which companies can compare performance; the development of positive performance measures; the findings and outcomes of the detailed analysis of electrical energy; shocks; the provision of information to industry; an outline how the data is being used to determine departmental; operational priorities; and future plans to undertake research into the other areas identified.

Jan 1, 2003

By K Le Bron

Fatalities that occurred because of rock falls in off-reef excavations (excluding shafts) over the last three years range between ten per cent and 20 per cent of the total number of fatalities that have occurred due to rock falls in the South African mining industry. These rock falls, mostly exacerbated by blasting practices, occur because of failure on discontinuities within the rock mass. Among other reasons of their occurrence is insufficient support installation or the incorrect assessment of rock mass conditions. This report presents qualitative analysis intended to outline rock stability conditions in tunnels subjected to dynamic loading. Seismic waves including those created by firing an explosive charge in tunnel rocks are considered. The rock behaviour is monitored using geophones and extensometers variably installed to record the near and far effects of roof bolt support units on a dynamically loaded rock. The paper discusses the results of field investigations.

Jan 1, 1999

By J Manuel, N Ware

Ideal iron ore sinter is produced by optimising the balance between coarse (+2 mm), stable ore nuclei and a reactive matrix consisting largely of fluxed -1 mm fines. The authors have previously published work evaluating the matrix melting behaviour of a number of fine ores, using techniques developed by CSIRO. The focus of that work was to demonstrate the contribution of the matrix to overall sinter quality, with the results showing a direct correlation between melting point, matrix porosity and strength. CSIRO has also developed a complementary test to study the behaviour of coarse ore nucleus particles in contact with the sinter matrix and provide an evaluation of their reaction and assimilation properties. This test provides valuable fundamental information that can be used to better understand the role of specific ore types and optimise blend composition.The CSIRO laboratory-scale assimilation test is carried out by embedding particles of ores of specific sizes into a fluxed matrix of known sinter blend composition, using real ores and fluxes, in a laboratory test that directly relates to pot-grate and plant sintering conditions. Samples are fired under controlled conditions in a tube furnace using a standard heating profile and a constant, low-oxygen potential atmosphere. These conditions simulate the actual sintering process while removing the effects of the many locally-variable parameters (eg temperature, oxidation potential and localised chemistry) that exist in the actual process, meaning that trends in behaviour can be more clearly seen. Designed as a compromise between the industry-standard pot-grate sintering test and a more fundamental test using chemical reagents, the aim is to isolate and evaluate the nucleus behaviour of an individual blend component to allow an improved understanding of the role that an individual ore plays in a specific blend. Measured cross-sections of the resulting fired samples provide a semi-quantitative measure of reactivity, while accompanying photomicrographs allow a qualitative assessment of assimilation properties (eg volume and distribution of secondary porosity generated during reaction).In this paper, to complement the previous work published on melting behaviour, nucleus particles were selected from hematite, hematite-goethite and goethite ores and embedded in a simulated plant sinter matrix. Drilled core particles of two sizes were tested at fixed temperatures simulating low- (<1300°C) and high-temperature (>1300°C) sintering conditions. The resulting assimilation properties are compared and discussed as a function of particle size, temperature and ore/sinter mineralogy. The implications for the contribution of each component to the prediction of blend sinter quality are also discussed.CITATION:Ware, N and Manuel, J, 2015. Fundamental nucleus assimilation behaviour of hematite- and goethite-containing ores in iron ore sintering, in Proceedings Iron Ore 2015, pp 77–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By N C. Steenkamp

The Northern Cape Province of South Africa is host to the Kalahari Manganese Field (KMF). The northern portion of the KMF hosts high-grade manganese referred to as Wessels’ type ore and is mined mostly from underground operations. WorleyParsons TWP is currently involved with the development of a ventilation shaft for one of these mines. The main challenge is to develop through the unconsolidated Kalahari material and weathered portion of the Karoo formation. These formations are preserved very erratically over short distances. A lack of understanding of the unique challenges presented for developing shafts in this area has resulted in the failed development of a shaft on an adjacent property and over-expended budgets on others.The renowned red sand of the Kalahari forms the top several tens of metres and overlies a horizon of gravels and calcrete that pose seasonally variable water ingress problems. A very stiff red clay horizon is then intersected. The Red Clay is prone to swellling during excavation and has been the main stumbling block on previous constructions. The standard approach has been to develop non-stop through this layer. The red clay is underlain by another horizon of calcrete, gravel and conglomerate that marks the bottom of the formation. The top of the Dwyka Tillite (Karoo Formation) is usually highly weathered and has a distinctive yellow colour. The weathered tillite is highly susceptible to drying and becomes friable. At reef-intersection, the combination of subhorizontal bedding and joints with the dominant subvertical faulting results in potential wedge failures in the manganese and ironstone units.This paper describes the geotechnical issues identified during the planning of the ventilation shaft and the risks associated with development through the Kalahari and weathered Karoo Formations. A new approach to developing ventilation shafts in overcoming these challenges is recommended.CITATION:Steenkamp, N C, 2014. Challenges of developing a ventilation shaft in Kalahari and Karoo formations, Northern Cape, South Africa, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 81–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Vanderberg B

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras. Todays common approach of utilizing only a single camera system can, in some cases, lead to great errors and erroneous conclusions when motion is assumed to be in a predefined plane of motion. CMe phrase, "What you see is what you get, it no longer true in 3D."). This is especially true in blasting environments which exhibit complex and/or predominant structural geology. The 3D system eliminates this problem, and includes automatic corrections for vertical and horizontal camera optic axis orientation, dimensional controls, lens distortion, field set-ups, projection imaging and digitized inputs. The only information required is the surveyed or known coordinates of at least six non coplanar points in the field of view. Motitn from each camera view is then digitized, transformed through a direct linear transformation, and processed with the 3D software, which also automatically time matches the data, even when the high-speed cameras are operated at different speeds. Eleven calibration constants are generated using an overdetermined system of linear equations to output the true 3D coordinates of motion in the time domain. Applications for this 3D approach are not restricted to just analyzing the kinetics of a blast. The system is sufficiently flexible to allow an accurate, quick and economical method of bench face profile analysis, generate muck pile profiles and estimate volumetric calculations. The recording systems for these applications can be common 35mm still photography and/or video equipment. It is envisioned that this system will soon replace expensive laser surveying systems at a fraction of the cost in the near future. It is also an excellent system to accurately quantify drill pattern layouts and the spatial locations of each blasthole. This information is required for generating single hole based synthetic seismograms to accurately predict the vibrational outputs of full scale blasts. In terms of litigation concerning claims resulting from blast induced ground vibrations to structures, the system is proving to be an excellent and economical method of performing pre-blast surveys where differential settlement is suspect.

Jan 1, 1990

Late Cretaceous and early Tertiary coals in the Greymouth, Ohai and Kaitangata coalfields represent a major national energy resource comprising-up to 2500 x 106 tonnes of coal in ground. The three coalfields are closely related in terms of age and sedimentary and structural character. The most striking feature common to all is the complexity of the geology which has severely restricted exploration and mining of these coal resources. This complexity is manifest in the irregular lensoid nature of coal seams and by the incidence of unpredictable medium and small scale faulting and folding. There are many geological similarities between these coalfields which are considered to arise from a common origin which can be related to the plate tectonic evolution of the southwest Pacific region. In order to efficiently assess and exploit these coal resources it will be necessary to know their geology in great detail. This can he achieved by increasing the understanding of the sedimentary and structural evolution of the coal bearing basins. This knowledge may be gained by the application of traditional (ie drilling, field mapping) and innovative techniques (ie high resolution seismic, in seam seismic) with on going research-oriented studies (ie basin analysis, coal petrography).

Jan 1, 1987

By S Azam

Coal is a vital energy source and source of carbon for metallurgical applications, contributing significantly to the world economy. Coal mining and processing involve multiple processes that generate Respirable Coal Mine Dust (RCMD), one of the primary sources of health hazards for coal workers. Since 2000, the rate of Coal Workers’ Pneumoconiosis (CWP) has continually increased in the U.S, with severity of the cases also worsening. Increasing evidence shows that exposure to RCMD in coal workers is a high-risk factor for lung cancer, which causes more deaths than the following three major cancers combined in the US Recent observations show an increased incidenceof CWP or other lung diseases, particularly among young miners in the Appalachian basin. The CWP prevalence in Appalachia is four times higher than the national average. Although various regulations are in place, the resurgence of such disease among coalminers demands additional efforts to better understand all the possible facets of coal dust toxicity, taking insights from current interdisciplinaryresearch efforts. One such important field is the interaction of coal dust with moisture in underground mines. Although moisture is prevalent and dynamic in an underground mining environment, it has never been evaluated for its impact on modifying the toxicity of coal dust and transport or flow behaviour. However, research conducted in atmospheric sciences in the past decade makes it clear that moisture in the atmosphere can significantly alter the behaviour of mineral dust. This paper is a part of research aimed at understanding how moisture interacts and alters the characteristics of coal dust. Such insight is crucial in understanding the potential toxicity of coal dust and developing mitigation technologies.

Oct 12, 2022

By Haslam C. O, Taylor S

Four historical periods of Australian lead-zinc-silver exploration and development are identified.In the first period, 1841-1900, Australia's deeply weathered surface yielded bonanza deposits. The outcrops of easily worked secondary ores, enriched in silver and lead, were discovered by prospectors with the incentive of production at times of high silver price. Districts discovered in this period still contributed, in 1982, 60 per cent of Australia's lead-zinc production, mainly from Broken Hill.The second period 1901-1944, was one of strong mine development but stagnant lead-zinc-silver exploration. Mount Isa was discovered and developed, but otherwise effort was devoted mainly to the mining of deposit extensions and to the metallurgical flotation of zinc. The deposit discovery rate was low but the discovery of Mount Isa was so significant that discoveries of this period contributed, in 1982, 30 per cent of Australia's lead-zinc production.The third period 1945-1972 was one of re-invigorated exploration.New geological and geophysical surveys, developing concepts of ore genesis, and worldwide comparisons of orebody settings improved target area selection. Evolving remote sensing methods, and rapid analytical techniques, assisted detection of lead-zinc deposits. Initiation of exploration led to discovery:1. in regions of previously unsuspected lead-zinc-silver potential (Sorby Hills, Mons Cupri, Golden Grove).2. of poorly exposed deposits in recognized mineral districts (Hilton, H.Y.C., Woodlawn, Elura, Que River).3. during active exploration for another commodity (Brown's, Woodcutters, Mary River, Beltana, Lady Loretla and Pegmont).The period saw a sustained growth in lead-zinc-silver production mainly from established operations. Mines discovered during the third period contributed, in 1982, 7 per cent of Australia's lead-zinc production.In the fourth period from 1973 to the present, exploration initiatives became fewer but resulted in continued discovery of poorly exposed deposits at Teutonic Bore, Thalanga, Benambra, Scuddles, Hellyer, and Jillawarra. Development initiatives strengthened in the period and production commenced at Woodlawn, Teutonic Bore, Que River and Elura; pre-feasibility work commenced at Scuddles, Hilton, Lady Loretta and Thalanga.

Jan 1, 1984

Full aerodynamic design development of the proposed fans for the enlarged primary ventilation system at Mount Isa Mines Limited was initiated before tender specifications were prepared. Theoretical and analytical design studies were made of many possibilities to determine the optimum proposal. Major considerations were efficiency, simplicity, standardization, and mechanical feasibility. Model testing and experimental work covered blading design, inlet shape, diffuser and tail fairing dimensions, instrumentation requirements, ancl noise studies.Theoretical and predicted performance estimates were prepared for the three 20 ft diameter vertically mounted axial flow fans.

Jan 1, 1967

By Nye P. B, Fisher N. H

At the second Empire Mining and Metallurgical Congress held in 1927, the Empire Council of Mining and Metallurgical Institutions was formed and it was proposed that the Council take steps to prepare a "Review of the Mineral Resources and Industries of the Empire." At the third congress in 1930, it was resolved that the proposal to institute the review should be submitted to the Imperial Conference held in 1930. This was done, and the Minerals Committee, of the Imperial Economic Committee compiled, an interimreport which was based on statistics of imports and exports, and did not consider resources and consumption.In 1942 the Institution of Mining and Metallurgy, London, wrote to the Empire Council and stated that it was desirable that the Council should be in a position to take part in decisions affecting the future of the mining and metallurgical industries. The Council communicated with the constituent Institutions regarding the nominations of two members then in England. Subsequently the Mining, Geological and Metallurgical ,Institute of India prepared a review of the mineral resources and industries of India and their post-war development, and the Empire Council forwarded a copy to the Australasian Institute of Mining and Metallurgy and asked if that Institute would submit a review on simjIar lines for Australia. The Australasian Institute arranged that the Australian review should be prepared by...

Jan 1, 1946

By Rais SA

In June, 1986, Freeport Indonesia, Inc., in conjunction with Out- okumpu USA, laboratory tested the Flash flotation concept on Primary ball mill underflow. These laboratory results indicated a possible 10% increase in precious metal recovery and 0.6% increase in copper recov- ery were available over conventional methods. By October of the same year two Outokumpu Skim Air SK-240 units were operational on one mill circuit and were achieving 5 to 10% increased recovery in precious metals with equal copper recovery at one percent higher final concentrate grade. Two more cells were purchased and installed on the remaining grinding circuit in July, 1987. As part of the installation of the Skim Air cells, an existing cluster of six 508mm Krebs cyclones were replaced by four 660mm Krebs cyclones. To reduce high circulating loads, these new cyclones were made horizontal at 45 degrees. This arrangement succeeded in reducing the mill circulat- ing load by 100% and has allowed for a 10% increase in throughput at the same grind.

Jan 1, 1988

By M Kizil

Mining Engineering Degree programs have traditionally had a practical emphasis and have been highly vocational in nature. However, over the years, there has been an increasing attention to the more scientific aspects of the discipline. More recently, the professional institutions, the industry and the community at large have placed increasing emphasis on the broader aspects of the professions: management, finance, humanity, environment and social issues. Notwithstanding this, there has been a continuing emphasis on the practicalities, and most Mining Engineering programs are still strongly vocational in nature. But employers of new graduates complain about the graduatesÆ lack of practicality and readiness for employment æat the sharp endÆ on the mine site.This paper briefly describes some of the more recent developments in the Mining Engineering Degree program at the University of Queensland that attempt to address the problem. Particular attention is paid to alternative learning programs, including applications of virtual reality, practical experience at the University Experimental Mine (UQEM), and the Undergraduate Site Learning Program (USLP).

Jan 1, 2002

By Sneddon NW

Aberdare North Colliery is situated on the eastern boundary of the City of Cessnock in the Hunter Valley, New South Wales. Although the area is now noted for its wines and vineyards, the district has a long history based on coal mining. The richest coal seam in the Cessnock district is the Greta Seam, a low ash, high volatile steaming or gas making coal. The seam, up to 10 metres thick, extends over a large area surrounding the city of Cessnock and neighbouring townships such as Bellbird, Aber- dare, Kearsley, Neath, Ellalong, Kurri Kurri and Stanford Merthyr. The Aberdare Colliery, leases, which extend under Aberdare and Cessnock townships, were first worked in 1905 and continued developing pillar panels until the mine closed on 11 Nov- ember, 1960. Coal mining to this time consisted mainly of developing pillars to the 2.4 metre parting and, in some areas, dropping the top coal to the 6 metre parting, thus leaving the pillars intact, the top 1.8 metr-es of coal be- ing left untouched due to the high sulphur content. Aberdare North Colliery was opened in 1956 in order to recover and extract the pillar coal and tops left standing for over 40 years. During the pillar extraction phase the occurr

Jan 1, 1981

By Bevilacqua P, Preti U

The basic separation phenomena taking place in film concentration processes are studied through a kinetic-probabilistic approach. This approach is based on the fact that the particle velocity in the film separation phenomena is a random variable and may be defined by frequency distributions and probability laws. The approach requires: 1. development of probabilistic models for describing the behaviour of particles having different specific gravity and size along selected trajectories in the separating devices; 2. setting up an experimental procedure for determining the relevant frequency distribution curves at the exit of the separators for the particles mentioned above; 3. estimation of model parameters and model validation. In the paper, the model equations are given for the mass distribution of particles on the surface of separators, the mass distribution at the exits of shaking tables and the residence time distribution in channel type devices. The relation between residence time distribution and particle velocity distribution is derived. The test procedure has been defined and results are reported for the exit or residence time distribution in channels. A comparison between experimental and calculated frequency distributions is reported.

Jan 1, 1993

By Y Mita, T Iwama, R Inoue, S Ueda

In the iron and steel manufacturing industries, efforts are being made to achieve carbon neutrality by 2050, and the transition from a coal-based steelmaking process to that utilising renewable energy is being pursued. An alternative process in which directly hydrogen-reduced iron is melted in an electric furnace is being investigated. It is known that foaming slag reduces heat loss from the steel bath in electric arc furnace, but iron loss due to the suspension of steel particles in the slag is indispensable. To improve the separation of steel particles from the slag, the control of the slag viscosity is important. Although the slag viscosity has been extensively studied, in those studies the slag was considered to be a simple liquid. However, in actual operations, slag is a multiphase fluid consisting of solid, gas and liquid phases. Therefore, in this study, by measuring the sedimentation velocity of titanium, stainless steel and glass spheres in an aqueous glycerin solution containing bubbles generated by the reaction between NaHCO3 and C2H2O4, the apparent viscosity of the gas-liquid fluid was evaluated based on Stoke’s law. It was found that the apparent viscosity of the gas-liquid fluid is larger than the viscosity of liquid phase and depends on both the bubble volume ratio in solution and the density of the falling solid sphere, and the apparent viscosity was different from that previously obtained by the rotation method. The apparent viscosity derived from the sedimentation velocity of solid spheres changed depending on the specific gravity of the ball. This is because the apparent viscosity is derived from the velocity of a ball falling in a static bubble in this method, whereas that is derived from the force applied by a stationary flow in the rotational method.

Aug 21, 2024

By S D. Dessureault

The largest surface coal mine in North America requires complex materials handling infrastructure to fulfil the highly variable quality specifications of its contracts. These diverse demands, reflected in the arrival of numerous customer trains every day, necessitate the integration of information in every stage of production. To meet this goal, quality measurement, train line-up and mine planning processes are being integrated into local and remote control rooms. The effectiveness of such a system can only be measured by comparing decisions that are made with, and without, each of the individual integrated control systems. Traditionally, mine controllers use their experience, intuition or a variety of trial-and-error spreadsheets to determine the ideal materials handling flows needed to achieve the correct quality. These balanced decisions are complex since many factors must be considered such as the mine plan, fleet costs, quality variability and others; consequently mine controllers usually have widely varying success between crews.An evaluation model was developed to assess the impact of a decision support system (DSS) integrated in a control room for controlling the coal blending process. To this end, an ARENA-based simulator representing the whole production process can be used to pull performance and current materials handling settings directly either from the real-time systems in the mine, or from historical data. In this way, the same shift (breakdowns, cycle rates, etc) can be simulated and performance compared. Different settings of the DSS, in terms of what information is displayed and the methods for doing so, can be tested for effectiveness. The historical data are extracted directly from a corporate data warehouse, without altering the everyday working databases. At the same time, the simulator writes its results back into the same data warehouse structure, allowing the same KPI reports to be used to measure simulated shifts.

Sep 26, 2011

By Hinton A. T

Three, and possibly four, distinct types of quartz-vein associated gold mineralisation are recognised in New Zealand. They are: epithermal, schist-hosted, metagreywacke-hosted and metamorphic core complex associated types. Each has a unique geological environment and structural regime which has provided the gold source, scavenging mechanism, emplacing mechanism and geometry. Each has a characteristic suite of associated metals and trace elements. The first three types form economically important gold deposits while the fourth type have been historically worked for gold and base metals. Intense exploration is currently being focussed on all four types.The epithermal type is typified by the extensive vein systems of Martha Hill, Karangahake and Golden Cross and numerous smaller examples. The veins were deposited in a near surface active volcanic environment from deeply circulating hot water. Their structure is tensional, veins are vertical-to sub-vertical and have limited depth. Their geochemistry is identical to that in active felsic hydrothermal centres in the central North Island. Major minerals are gold, pyrite, arsenopyrite, galena, chalcopyrite, sphalerite and argentite.

Jan 1, 1990

By Weller KR, Lim IL

The high pressure grinding rolls is one of the few new comminution devices that offer substantial savings when compared with traditional crushing and grinding circuits and with SAG milling. The machine has been well accepted in the cement industry, but mining companies have been more cautious in adopting this technology, partly because of wear and availability problems, and partly because of uncertainties in designing circuits which will deliver the power savings without complicating downstream processing. This paper addresses the latter problem by providing a model structure for predicting power draft and throughput from measurements made with small pilot scale high pressure rolls. Three existing models for predicting product size distributions are assessed and suggestions made for future work. The model structure comprises a power equation, incorporating measurements of torque and rolls speed previously used by the authors. Transport through the mill is assumed to be plug flow. Throughput is governed by the equilibrium gap between the rolls, which is determined both by machine settings and the physical properties of the feed material, including its size distribution. Therefore some form of physical testing in a model machine is required to determine throughput parameters. Results from copper and nickel ore experiments covering a wide range of machine conditions are presented and compared with model predictions. Model assumptions are discussed and directions for future work Suggested.

Jan 1, 1993

McLeod: Without getting into the argument as to how well we can know our resource levels specifically in the immediate short term, I would like to make one or two points about the future, and perhaps try and persuade people that they are not really facing a doomsday. It is fair to say that over the last few years the rate at which we have increased our resources has far exceeded the rate at which we have used them, and this is likely to continue for quite a few years yet. As people are now looking for a substitute for petroleum, later on we will be looking for a substitute for coal, should the position get serious. After all man is pretty versatile, has plenty of initiative-and makes allowances for experience. It has been demonstrated here by the way people are looking at use of low quality coals and better use of the coals that are available. It would be fair to say that what now we regard as economically submarginal deposits will, by the time we need them, become economic. I think that there is quite a lot in front of us in exploration and finding new reserves. I would like to have comment from yourself sir, because I recall reading a report of a meeting, here in Wollongong I think it was, in which you addressed the local branch on the future of coal in Australia, and you said that the coal basins of Australia had been well explored and there was not much chance of new discoveries. Since that time we have seen some thousands of millions of tonnes turned up in the Galilee Basin of Queensland, we have seen five hundred million tonnes turned up in Lake Phillipson in South Australia. Do your previous comments still apply? I would like to hear from some of the exploration people, who are operating on an Australia-wide basis, as to how they regard our chances of discovering significant new deposits and significant extensions of known deposits. H,artnell: Mr. McLeod has asked me to comment on what he has just said. I think that the important thing is that our knowledge of the main coal basins in Eastern Australia is increasing in detail but for the most part the extent of coal basins is not being increased in respect of their superficial areas. There are additions but they are not substantially changing our expectation of what the main coal basins will be. I believe that our task is essentially to intensify our knowledge of the main coal basins that we know about. This is important for example for the various reasons that Mr. Roach was talking about, that is the problem of surface alienation, jeopardising the chance of recovery when you go to underground operations. My approach to this whole problem is predicated on the belief that coal has a special destiny to perform in the next fifty years. I believe that it is going to take up to fifty years and maybe a little longer before the enormously demanding technology for nuclear power recovery is in fact achieved. When it is achieved the supply of energy to the world will be enormous, much beyond what we have ever even dreamed about. The mind boggles at what the people of the middle of next century, of two thousand and fifty, will command in the way of physical resources. It is going to be, I believe, tremendous, but the technology involved is very demanding. I mentioned to Mr. McLeod the other day that according to the information that I got in November last, 60% of the nuclear power stations in the United States were out of action, by automatic cut offs because of safety requirements. The technology of breeder reactors seems each year to be a bit further off. In the meantime coal I am sure is going to be called on to supply power directly to fluidised bed and other technologies for power generation. It is going to be called upon in the near future, I believe, to supply liquid fuel on a vast scale and the only thing in my view that we should be thinking about is whether the coal producing countries of the world will succeed in producing as much coal as is going to be demanded. I believe the real challenge to the coal mining industries of the world is that they may fail to do what is going to be demanded of them. This is a challenge I believe to mining technology. I think that we should be working deliberately and energetically finding ways and means where underground recoveries, instead of averaging 50%, can average 50% plus, plus, plus, and this is the first requirement. We should be spending many millions every year, here and overseas, on increasing our means of winning coal because every tonne of coal that is alienated and left irrecoverable in the earth is going to weaken the capacity of the coal mining industry to fulfil, what I believe to be its destiny in the next 50 years.

Jan 1, 1975