Search Documents

By P Waters, S Miller

BHPBilliton operates the Mt Whaleback Mine located in the semi-arid Pilbara Region of Western Australia. Approximately 200 Mt of net acid generating (NAG) material still remains to be mined. Acid Rock Drainage (ARD) was first identified at the site in 1995 following cyclonic storms. This resulted in the development of strategies that have allowed the mine to successfully manage ARD whilst continuing to operate. BHPBilliton Iron Ore is working toward prevention of ARD in its operations, however, historical practices have left residual areas that must be considered. Three significant sources of ARD have been identified that must be managed: stormwater run-off from exposed pyritic shales in pit surfaces; basal flows beneath overburden storage areas following rainfall events; and contaminated water from pit dewatering. The mine contains all ARD water onsite. This is achieved by: storage of all affected water in the ARD dam; evaporation of affected water from the ARD dam and the adjacent evaporation ponds; pumping from upstream dams to prevent stormwater from being affected; and emergency storage and treatment in-pit as a contingency. The site ARD management strategy is approved by senior management and endorsed by State Government regulatory authorities and relevant external stakeholders. Additional strategies are also under evaluation to effect long-term closure of the operation. Record rainfalls from 1998 - 2001 have tested the capabilities of the ARD strategy and management plan. Learnings from these events, coupled with recommendations from an extensive technical audit in 2000, have been incorporated into the strategy for ARD management. This paper presents the strategy and an overview of the ARD management plan that can be considered and applied by other affected sites in the management of ARD.

Jan 1, 2003

Epicentres of recent shallow earthquakes in the region (3-12¦S, 126-150`E) were plotted to identify the various plate boundaries in the region, in particular the southernmost one marking the northern edge of the Australian plate. New and published fault plane solutions were examined to determine the style of faulting and state of stress along the Australian plate boundary. From east to west the boundary is first a subduction zone along the Solomon Islands, then a spreading centre across the Solomon Sea, a zone of compression and left lateral strike slip along the Papua Peninsula, almost pure thrusting across the centre of New Guinea and lastly left lateral strike silo through Irian Taya to the outer Banda Arc. The principal stress is very consistent, trending NW to NNW in a near horizontal plane, from the triple junction of the Pacific, Solomon Sea and Australian plates in the east to the Banda Sea in the west. Only along southern Solomon Sea plate margin which is a divergent boundary, is the stress different in type and direction.

Jan 1, 1987

Leadership challenges for mine management over the next decade will be primarily about doing more with less labour. This will require a greater focus on people leadership and management, reducing uncertainty by evening out employment peaks and troughs, understanding and addressing our demographic destiny and its implications whilst identifying and holding onto our mission critical employees, managing creativity and accepting diversity whilst providing flexibility in employment for work-life balance. Greater emphasis will also be required on the non-technical social skills of complex interactions with community and education providers and finally a greater emphasis on forecasting and planning for the provision of future skills needs. Skills needs will become an ever increasing priority in risk management as retention starts with attraction and remember: SATISFACTION = REALITY                                EXPECTATIONS These are the challenges and opportunities for leadership and mine management of the 21st century to assist in better meeting and maintaining our human resources needs and thus contributing to the sustainability of the sector in Australasia.

Jan 1, 2006

Studies of the minor element content of sphalerite and pyrite have generally been concerned with individual deposits or localised groups of deposits. However, a small number of more regional investigations have been reported (e.g. Davidson, 1962; Groves and Loftus-Hills, 1968; Loftus-Hills and Solomon, 1967; Price, 1972; Bralia et al., 1979) which have used the minor element abundances to evaluate the petrogenesis and geological affinities of diverse ore types and to fingerprint metallogenic provinces (e.g. Ivanov, 1964). While generally held to be valid, some doubts have nevertheless been cast on the reliability of minor element abundances in petrogenetic deliberations (e.g. Mercer, This paper reports on the distribution of he. Cpl and Mn in sphalerite, and Co, Ni and Mn in pyrite, from sulphide mineral occurrences within the "eugeosynclinal" prism comprising the New England Region of north-eastern New South Wales and south- eastern Queensland (Fig. 1). The occurrences examined are representative of two well-defined styles of mineralisation (Stanton et al., 1974) within which clear patterns of ore-rock distribution give rise to specific metal associations (Herbert. 1977).

Jan 1, 1987

By Shihui L, Lianfu Z, Llanming J

The paper considers the essence of the multi-objective decision-making issues for selecting an optimal mining plan, and analyses the advantages and disadvantages of the multi-objective decision-making techniques commonly used for selecting an optimal mining plan. It presents the principle and practice of using a group-AHD with mixed factors to select an optimal plan.

Jan 1, 1995

As part of a prefeasibility study being undertaken by Newcrest Mining Limited, the Cadia East Implementation Team has developed an access decline to the proposed underground operation. This paper describes new technologies that have been employed in this development, which include: high frequency drifters that have penetration rates one and a half times that of competitors, ensuring minimal increase in drill time, despite rounds greater than 5.5 m;automated drilling used in conjunction with laser navigation and face pattern design software, which facilitates exact positioning of hole collars, lengths and lookouts for accuracy and repeatability; andemulsion charging that reduces manual handling; has variable string loading capabilities, via its hose retraction system, for perimeter control and reduced fume characteristics. A Six Sigma improvement process was used to support the system change undertaken and demonstrated that development rates improved 60 per cent above the comparable single heading benchmark.

Jan 1, 2008

By G W. Wilson, C Panidis

Potentially acid forming (PAF) waste rock contained in dumps formed as a result of open cut mining of metalliferous orebodies are conventionally sealed or covered using a near-saturated, low permeability compacted clay layer, protected with a mulch layer and/or vegetated growth medium. The purpose of the compacted clay layer is to limit oxygen diffusion and the infiltration of rainfall into the dump. Where the aerial extent of the PAF waste rock dump is large, or where suitable clayey material is in short supply, it may be difficult to source sufficient suitable clayey material to form the cover. The paper describes a laboratory-based investigation of combining inert waste rock and tailings to form an alternative seal or cover material. The inert waste rock was sourced from the trafficked surface of a non-acid forming (NAF) waste rock dump, with a maximum particle size of about 100 mm. This was combined with NAF thickener underflow tailings slurry in various mass ratios, and the resulting mixtures tested for their particle size distribution, compaction characteristics, soil water characteristics (relationship between suction and volumetric moisture content), and saturated hydraulic conductivity. The mixtures tested ranged in consistency from those dry enough to be compactable, to those with the consistency of wet concrete that lend themselves to placement without the need for compaction. The laboratory test results showed that the suitability of the mixtures as seal or cover materials is very dependent on the particle size distribution of the mixture, with well-graded mixtures having substantial fines performing best.

Jan 1, 2003

By Onton W

During the latter part of 1936, conditions encountered in sinking the Main Ore shaft made it impractical and uneconomical to continue deepening it to serve haulage levels below the present No. 5 level. Plans were therefore made for an interior shaft, to serve new lower levels, that terminated above No. 5 level so that ore hoisted could be drawn off on this level and transported to the Main Ore shaft for final conveyance to the mill crude ore bin. The No. 2 interior ore shaft was only developed below No. 4 level and borehole ropeways with a winder located on the surface were installed in preference to an underground winder installation. No. 2 ore shaft with borehole ropeways commenced lead ore hoisting operations in September 1938. Apart from the copper ore hoisted in the war years of 1943-46, lead ore was hoisted to No. 5 level until September, 1951.

Jan 1, 1988

By Dunne R, Defilippi J

Dump leaching began at Teller in late-1988 at a rate of 4 MTPA and has been progressively expanded to the present rate of 10 MTPA. Teller's on-going commitment to dump leaching is driven by the amenability of gold ores to the process and the availability of large tonnages of low grade gold ore. The sequence of evaluating ores for dump leaching involves rolling bottle tests on coarsely ground ore, followed by small and large column leaching and finally trial heaps. Trial heap tests are very expensive and an alternative approach to this is large diameter column leaching.A four-column permanent facility was built at Teller to specifically evaluate the leaching characteristics of new dump leach ores. Details of construction, operation and dismantling are discussed in the paper. Capital cost for the four column facility was some $45 940, while operating costs are about $24 800 per column.

Jan 1, 1992

A Master of Applied Science degree course in Mining Geomechanics commenced in 1983 at The University of New South Wales, taught by extern- al (correspondence) studies. The course is aimed at graduates employed in the mining indust- ry, and especially people involved in geomechan- ics projects on a routine basis in remote locations. This kind of course is unique in Australia and is one of only two correspondence programmes available at this University. The author designed the course and nursed it through the early years, and was Director until 1986. The paper describes the teaching and assess- ment methods and also discusses aspects of admin- istration and coordination of such a course. It is concluded that an important need of the mining industry is being catered for and it appears that similar correspondence course for- mats would also be useful in other areas of the minerals industry.

Jan 1, 1986

By Sibson RH

The gold province of Otago occupies an area of upwarped basement, the Otago Schist, comprising predominantly quartzofeldspathic and volcanogenic metasediments. This assemblage is the product of collisional tectonic deformation and associated metamorphism, mainly to lower greenschist facies, during the Rangitata Orogeny (200-100 Ma). Historically this region has produced 240 tonnes of gold, 4% (10 t.) of which was from the mining of Cretaceous gold- quartz mineralised vein systems. Auriferous vein systems in the Otago Schist are mainly hosted within NW trending normal fault-fracture arrays, however NW trending reverse fault-hosted vein systems also occur. We propose that the Late Cretaceous-mid Tertiary Otago Schist structure represents a regional anticlinorium containing flexural folds of at least two wavelengths. The anticlinorium structure has been quantified by determining variations in angular discordance between schistosity and the Otago Peneplain, a Late Cretaceous-mid Tertiary erosion surface covering most of the Otago district. A structural model for the evolution of the post-collisional anticlinorium requires the cooling surficial zone (carapace) of a retrograding metamorphic belt to behave as an elastic lid. Erosion of topographic load on the carapace drove isostatic uplift, which was greatest in the tectonically thickened core of the orogen. In this way differential uplift produced flexural deformation in the elastic carapace, expressed as a large scale arching of the orogenic belt. Flexure created tangential longitudinal strains in the outer-arc, leading to extension and the formation of mineralised normal faults. These structures are separated by a neutral surface from shortening and associated mineralised reverse faults in the inner-arc. Our structural model predicts that the distribution of auriferous lodes should be localised about zones of maximum flexural curvature, where the tangential longitudinal strains are highest. As a result, NW-SE hinge regions separating schistosity dip domains in the Otago gold province may have new found significance as potential exploration targets.

Jan 1, 1995

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

The Yilgarn Block of Western Australia presents (figure 1) a number of problems for conventional diamond exploration based on heavy indicator mineral sampling. These problems are due to the geology and unique geomorphological development of the Yilgarn Block.Essentially the Yilgarn Block is a pene- plain developed on a craton composed of Archaean intrusive granitoid rocks with meta- morphosed greenstone; which, apart from regional uplift, has not been tectonically disturbed since planation by glaciation in the Permian. Therefore since the early Plesozoic the Yilgarn Block has been subjected to terres- trial weathering conditions. Bettany et al., (1984) identify two phases of particular importance in the development of the present landforms: 1. Periods of lateritization during the Tertiary which result in the ~lassi~al laterite profile (figure 2). Duricrust indurated : Fe and Al oxides Mottled zone : Clay and Fe oxides Saprolite or pallid zone : leached clay grading into fresh rock. 2. Subsequent periods of aridity and semi- aridity during which laterite development was truncated and reworking of laterite Occurred.

Jan 1, 1988

The Drummond Basin is a large intracratonic basin which developed in central Queensland during Late Devonian to Early Carboniferous times. It is postulated that the Drummond Basin developed as a foreland basin, to the west of a probable west dipping continental margin volcanic arc and subduction zone. The Drummond Basin sequence has been s,ibdivided into three tectono-sedirnentary cycles. Cycle I forms the base of the sequence and comprises thick sequences of intermediate to felsic volcanics and proximal volcanolithic sediments. The volcanics, particularly in the northeast of the basin, occur in separate sub-basins around what were probably isolated eruptive centres. In contrast, the rocks of Cycle 2 and Cycle 3 have been deposited during episodes of broad, basin wide subsidence. Five major igneous episodes, some of which may be co-magmatic, are recorded in the eastern Drummond Basin and environs between the Late Devonian and the Early Permian. The first and second episodes occurred during the Late Devonian to Early Carboniferous and are represented by the volcanics in Cycle 1 and Cycle 3. The third episode involves the intrusion of granitoids of Early Carboniferous age into the Drummond Basin sequence. These occur in the Ukalunda area and are related to gold mineralisation at Ukalunda and Valhalla. Episode four includes the felsic volcanics of the Bulgonunna Volcanics. This episode does not appear to he broadly auriferous but gold mineralisation does occur in possible basal Bulgonunna Volcanics at Mount Coolon. The final episode includes a suite of granitic intrusives which intrude the Bulgonunna Volcanics and which are considered to be co-magmatic with them. These intrusives do not appear to be generally associated with gold mineralisation. Gold mineralisation is widespread in the north- eastern Drummond Basin and environs. It is probable that the gold mineralisation is concentrated in epithermal cells during the Late Devonian to Early Carboniferous volcanic cycles. This style of mineralisation appears to be related to tectonic setting in modern analogues.

Jan 1, 1989

By Clarke DS, Sporli KB

Structure is an important control in the localisation of gold mineralisation in epithermal systems. There has been, however, only limited investigation of the structural elements involved; such a study is currently directed at the gold deposits of the Coromandel Volcanic Zone (CVZ). Here, mineralised veining and brecciation ranges up to tens of metres in thickness. Dips of veins are mostly steep, but not vertical, and there is a significant number of low angle veins.The structural control of epithermal deposits may be considered on four scales. At the mega-tectonic scale, pre-volcanism fault patterns mostly relate to separation of the New Zealand micro-continent from Gondwana. The major structural controls on mineralisation at this scale, however, are associated with the volcanic arc processes responsible for the CVZ. Post-mineralisation faulting are linked to the Hauraki Rift and the Colville Ridge-Havre Trough system. Regional scale faults controlling the distribution of gold deposits are the product of these tectonic events; much of the faulting may relate to rifting and calderas, but further work is required to demonstrate this. Detailed study is also needed on vein systems at the prospect scale to validate models of brittle deformation responsible for such systems. Evidence that a variety of structural mechanisms dominated in different deposits is found at the vein scale, with Coromandel gold deposits being classified according to their different styles of vein-fill texture.

Jan 1, 1990

Oceana Gold CorporationÆs (OGC) Frasers underground (FRUG) transitioned into production in early 2008. The mine uses a relatively unique yielding pillars mining method that takes its lessons from empirical coal mining practices more so than hard rock techniques. Being a low-grade, flat-dipping resource hosted in the highly structured relatively weak Otago schist in central South Island in New Zealand, meant a number of iterations were undertaken to find the right mix of mining cost and resource extraction. Mining is on the down dip extension of the active Frasers open pit at the Macraes site (that extracts the full shear zone package at a head grade of 1.5 g/t). The challenges for the FRUG feasibility study team was to deliver an net present value (NPV) positive operation that would exist as a coproduct with OGCÆs other New Zealand operations, allowing it to make use of the high throughput low cost refractory ore treatment facility.Key factors in the successful project design were: Net capital costs kept to less than NZ$30 M by realising significant gold revenues from mine development from month four onwards. Virtually eliminating waste development by putting all key capital infrastructure in the low-grade ore adjacent to panels and maintaining the option of extracting this resource on retreat from the mine. Targeting a specific higher grade halo ore package within the entire mineralised shear zone. Applying a mining method that accepted a higher degree of dilution, ore loss and resource loss (in yielding and non-yielding pillars) to the flat-dipping resource. Thus providing an acceptable margin per tonne and resource tonnes mix, as the resource could not support a conventional low-cost caving operation, nor a higher cost room and pillar or open stope and backfill operation. 2008 has seen increasing tonnes and grade performance with a corresponding decrease in cost per tonne and cost per ounce as the mine has reached nominal capacity and is producing an operating surplus. The challenge will be to maintain and improve.

Jan 1, 2009

Samples weighing 0·5 g are fused with sodium hydrogen sulphate, leached with 5 ml. of 4 M nitric acid and diluted to 10 ml. with water. An aliquot of the clear solution is boiled with concentrated nitric acid and then 2 ml. of a phosphotungstate solution are added. After dilution to 10 ml. with water, the solution is heated in a boiling water-bath for not less than 10 min. When cold, the solution is extracted with 2 ml. of iso-amyl alcohol and the yellow phosphotungstovanadate complex is compared with a standard series. Concentrations down to 4 p.p.m. may be analysed at a rate of 100 samples per man-day of 8 hr.

Jan 1, 1971

By Mousset-Jones P, McPherson M. J

This paper explains and discusses a computer program developed to deter- mine the optimum combination of fan pressures that will give a required distribution of airflows in a mine ven- tilation system. The program is based on an existing simulator, VNETPC and two experimentally developed relationships: (1) linearity between fan pressures and added regulator resistances and (2) a non- linear convex function relating the system air power and the fan operating Pressures.

Jan 1, 1988

Misima Mines Pty Ltd (MMPL) operates a large open cut gold mine on Misima Island in the Louisiade Archipelago in Papua New Guinea. Misima Island lies approximately 600 km east-south-east of Port Moresby. The island is 40 km long by 10 km

Jan 1, 1994

The paper discusses how automation is steadily proceeding throughout all areas of the electrolytic zinc industry. Fluid bed roasters with integral sulphuric acid plants are now on -computer control. Highly efficient, continuous leaching and purification stages, with feed-forward predictive and optimisation computer control, precede electrolytic cells with on-stream solution analysers and automatic stripping of deposited zinc. Controlled electric induction furnaces feed continuous casting lines, equipped with automatic stacking and strapping, machines, after computer based metal analysis has confirmed metal purity or alloy composition. The paper also discusses the use of computer models tied to process control systems, and the equipment and solution measurements that could be automated with advantage, using modern micro-based controllers and analysers.

Jan 1, 1985