Search Documents

By Y Xu, J Hacker, D J. Williams

Shear strength parameters of compacted clay liners are needed to analyse the stability of mine waste dumps containing compacted clay liners as sealing layers for potentially acid forming waste rock. A representative clay sample was supplied by McArthur River Mine from the mine site in the Northern Territory, Australia, with an average as-supplied gravimetric moisture content of about 13.6%. The clay was compacted in a 100 mm by 100 mm direct shear box at the as-supplied moisture content to a dry density of 1.85 t/m3, representing the field compaction specification adopted by the mine. To determine the peak and ultimate shear strengths of the compacted clay, single-stage direct shear testing was carried out at nominal initial normal stresses of 50 kPa, 100 kPa and 200 kPa, representing shallow depths of burial in the North Overburden Emplacement Facility of about 2.8 m, 5.6 m and 11.1 m, respectively (assuming a waste rock wet unit weight of 18 kN/m3). Three shearing rates of 1 mm/min (rapid), 0.1 mm/min (intermediate) and 0.01 mm/min (slow) were applied to study the influence of shearing rate on shear strength. In addition, the development of a residual shear plane was tested by reversal and re-shearing in the direct shear box. In the first shearing, the peak and ultimate shear strengths are determined. The normal load was then removed and the box rewound to its starting position. The normal load was then re-applied and the specimen re-sheared. Two reversals were applied to each specimen, and it was found that there was no significant reduction in shear strength. Finally, based on a range of shear strengths obtained in the laboratory for McArthur River Mine clay and other materials by various laboratories over time, shear strength parameters for the compacted clay were recommended for use by the mine.CITATION:Xu, Y, Williams, D J and Hacker, J, 2018. Shear strength of compacted clay liner at McArthur River Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 208–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

PIP is regularly engaged in businesses where Greenfield Capital Projects are under- delivering on the expected business case. In most of these projects, we can identify that rigorous review has been carried out on the design and financial cost elements and substantial reporting is maintained to Boards on progress versus plan of project completion and cost. However, in all sites of this nature that we have worked at, the planning, design and execution of the operational elements or æwiringÆ of the organisation have fallen short and resulted in significant extra cost or opportunity cost (lost tonnage or quality) during start-up. When compared to the amount of planning and resources that have been poured into the capital side, the ledger on the æwiringÆ side is typically fairly sparse. This presentation outlines the importance of running a disciplined, rigorous process to prepare the human and wiring side of a start-up to ensure rapid start-ups and put the site on the pathway to high performance. It gives an outline of the rigorous process PIP has used with projects to ensure excellent start-ups.

Jan 1, 2006

Gekko Systems Pty Ltd have developed the Python Underground Processing Plant for the concentration of gold and sulfide ores. The Python plant has an established flow sheet including fine crushing, screening, gravity separation and flotation which aims to concentrate the valuable minerals (gold/sulfides). The aim of the plant is to achieve high valuable recovery into a mass yield of 10 - 30 per cent to reduce the amount of material that is needed to be taken to downstream processing. This paper examines the test work protocol for testing an ore to assess its suitability for the Python flow sheet. This paper will discuss the test methods employed to determine crushing requirements, continuous gravity recovery and flotation performance and how the results relate to Python design for the comminution, gravity and flotation circuits. Results from past test work will be discussed.

Aug 1, 2010

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By H Austrheim, A K. Engvik, A Putnis

How aqueous fluids move through rocks and minerals is a question of possible pathways and mechanisms. Existing pathways such as fractures and grain or mineral boundaries provide obvious channels for fluid movement. We show how minerals reactive in the presence of an interfacial fluid can be replaced by new product phases through a process of interface-coupled dissolution-reprecipitation. A resulting porosity in the new phase provides a new pathway for fluid movement and therefore mass transport through the mineral, which progressively reacts at a moving interface. Eventually fluids of new and changing composition can pass through originally solid minerals and move on further, taking remobilised elements with them, to be reprecipitated whenever the chemical and/or physical conditions allow. One such example is albitisation of rocks associated with mineralisation.

Jan 1, 2008

Batch centrifugal gravity concentrators have become standard equipment in gold grinding circuits for recovery of gravity recoverable gold (GRG). The downstream benefits of installing a gravity circuit are well understood, and in general, if there is a reasonable amount of GRG in the ore, a gravity circuit is usually installed. The benefits of gold gravity recovery have also been well documented, with a large database of successful case studies. As well, predicting production scale gravity recovery results ahead of installing gravity has become a common practice. The missing link between lab and full scale has always been the ability to predict the recovery benefit of installing gravity ahead of actually doing so. Being able to predict the recovery benefit in advance would help an operation in assessing the economic benefit and help justify the capital costs of the gravity circuit with much less uncertainty.

Aug 1, 2010

By O V. Vasyukova

Formation of porphyry-style ore deposits starts with the metal extraction from magmas at so-called magmatic-hydrothermal transition (MHT). The processes and compositions at MHT are difficult to study as the record of them is poorly preserved. As the MHT is characterised by massive crystallisation of quartz, including quartz æeyesÆ and veins, their study can elucidate questions related to metal transport and deposition. Quartz grains from the porphyry deposits all over the world (Antapaccay, Peru; Batu Hijao, Indonesia; Climax, USA; Panguna, PNG; Far Southeast porphyry, Philippines; Rio Blanco, Chile; Omsukchan, Russia) were studied by optical, SEM-CL and BSE microscopy, electron microprobe and LA ICPMS. Quartz grains, even within each sample, have different shapes (rounded, egg-shaped, amoeboid or euhedral) and cathodoluminesence (CL) patterns (shape, number and width of bands in CL images). The outer layers of quartz are markedly different, which is unexpected if the grains had formed in the same conditions. Inflections and blurring of CL bands are often structurally associated with fractures that are commonly healed with secondary quartz and associated fluid inclusions. Our results show that quartz æeyesÆ could not crystallise from a silicate melt as normal phenocrysts. It is likely that in situ segregation of residual SiO2- and H2O-rich liquid and its solidification followed by coagulation (eg formation of silica-gel globules) took place in the magma (crystal mush) during MHT. Such globules could remain in a plastic state for a long time even at rather low temperatures. The solidification of globules occurred after bands of different composition had formed and led to fracturing of solidified and inflection of unconsolidated layers. All fluids (liquid and vapour) released from the original silicagel during solidification were trapped as inclusions (aqueous, salt-rich and sulfide). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

'Industrial Minerals - their mining and use in New Zealand' is the theme of the 1978 Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy. This paper describes the use of phosphate rock, sulphur and potassium chloride (potash) - three industrial minerals which have enabled the farmers of New Zealand to increase production to current levels. The growth of imports of these raw materials for the New Zealand fertiliser industry is well documented in NZ Fertiliser Statistics 1977. This is the most recent of the Ministry of Agriculture and Fisheries annual publications on this Subject prepared from the detailed returns of fertiliser manufacture and sales from each fertiliser works. There are now 12 of these works in New Zealand one of the most recently established being in Whangarie where this conference is being held. Its capacity to manufacture superphosphate will shortly be 300 000 tonnes twice that when it opened late in 1964. New grinding and manufacturing equipment comes on stream early in 1979. This paper illustrates the interdependence of two primary industries, agriculture and mining. New Zealand's economy in the foreseeable future will be based on agriculture so that our standard of living is dependent on the overseas prices and freight costs of the bulk raw materials from which our fertilisers are made. For the year ended 31 March 1978 New Zealand's total exports were $3395 million, of this total $2413 million (71%) came from the products of pastoral agriculture (wheat, wool, dairy and other animal products), $291 million from forest products and $501 (15%) from manufactured exports. Approximately half of the pastoral receipts can be attributed to the fertilisers applied at a total cost of about $200 million including subsidy.

Jan 1, 1978

By W Ludlow, C Harrington

This paper presents an overview of the design and construction challenges to implement capping systems on Tailings Storage Facility’s (TSF) based on recent projects in Australia. Key aspects discussed include the cover design and barrier system to encapsulate the tailings, designing for a service life of 1,000 years, water management considerations. construction on tailings, vegetation selection and agronomy of the available capping soils plus the Health, Safety and Enivornmental challenges faced in working on tailings. Lessons learned from experience in capping TSFs are also presented. CITATION:Ludlow, W and Harrington, C, 2018. Experience with Capping of Tailings Storage Facilities for Decommissioning Projects in Australia, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 157–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By M Olsson, I Bergqvist

A Swedish table of blast damage depths has, in one form or other, been in use since the late-1970s. Its history and the underlying theory are described. New experimental and theoretical findings that point out a number of shortcomings in the table and the underlying theory are presented and discussed. A revised version of the blast damage table was recently introduced in conjunction with new but incomplete recommendations for cautious perimeter blasting. The new table leaves the difficult task of taking into account factors like decoupling, water in the borehole, the rock properties, type of initiation, charge length and the actual bit diameter to the user. This paper discusses different ways of doing this, based on the experimental findings and a recent formula for the prediction of the lengths of radial cracks behind the half-casts. The material presented in this paper is meant to supplement and extend the new Swedish recommendations for cautious perimeter blasting of tunnels, shafts, pits and road cuts.

Jan 1, 2001

By S MacKinnon, J Kok

Potential areas for improvement in flotation performance were identified during JKTech model development surveys in October 2003. Subsequent implementation of the JKTech recommendations in consultation with flotation cell manufacturer Outokumpu have resulted in gold flotation recovery increases of more than four per cent over a two-year period. One of these recommendations was the installation of High Shear Stators in the Cleaner and Recleaner flotation cells. The High Shear Stator installation project was justified based on simulations completed using JKSimFloat. Bubble size measurements completed before and after installation of High Shear Stators showed a reduction in mean bubble size of approximately 50 per cent in the Cleaner cells. Both Cleaner and Recleaner banks showed a significant narrowing of the bubble size distributions following the installation. Plant gold recovery increase resulting from the installation of High Shear Stators was 1.1 per cent, with a 1.9 per cent increase in flotation gold recovery and 5.4 per cent increase in flotation sulfur recovery. Based on the 1.1 per cent recovery increase and total project cost of less than $200 000, the High Shear Stator Project NPV was $8 200 000 with a 0.25 year payback period.

Jan 1, 2006

By Hannan JC

Consent to develop and operate a new coal mine in New South Wales (NSW) will be conditional upon a number of environmental controls. In NSW, applications for any new major development associated with coal mining are determined by the Minister for Planning and Environment. The environ- mental conditions placed on the development consent, the coal mining lease and the approvals, and licences under the pollution control legislation amount to a substantial component of any new project's commissioning considerations. The nature, scale and location of projects and the principles of pollution control on which conditions of State Pollution Control Commission (SPCC) approvals are based have a considerable influence on project planning. The design, construction and operation of coal mines in NSW has been progressively modified over the past 15 years, to incorporate increasingly stringent requirements for environmental management. These requirements are in turn, a reflection of a greater community demand for environmental protection.

Jan 1, 1986

By F Grobler

Many projects fail because project performance in unfavourable economic conditions was not anticipated at the investment decision stage. This type of failure may have been avoided through the selection of a strategy that enables the project to perform well under a range of possible future economic conditions (a ærobustÆ strategy); rather than an æoptimalÆ strategy for expected future conditions that will never eventuate. This paper describes a method of rapidly generating mine plans for a number of project strategies, and then evaluating it against a representative range of equally likely economic conditions. The key performance indicators derived for each strategy are the mean value and the distribution of values (variance). A prudent investor will identify prospective strategies not only on the merit of highest mean values (as a proxy for economic reward), but also on the probability of not meeting specified investment hurdles (a proxy for risk). A robust strategy will achieve its financial objective even under adverse economic variations. This paper focuses on the effect of commodity price uncertainty; particularly around the choice of mining and processing capacity levels. Results from enumerating 2000 prices scenarios against 63 strategy combinations show how processing and mining capacity can be manipulated to manage the risk-reward trade-off.

Sep 26, 2011

By Salmon P. T, Gilmour R

Commercial production of zinc started at the Pasminco Metals - EZ Plant, Hobart, Tasmania, in 1921. Since that time the capacity of the plant has been steadily increased to its present level of almost 220 000 tpa. Major areas of the plant have been successively upgraded over a number of years, (Roasters, 1969, 1975; Acid Plants, 1981; Casting, 1972; Residue Treatment Plant, 1971), but, until recently, the leach/purification area remained virtually unchanged from the time the plant was built. The major redevelopment of the hydrometallurgical plant began with fully integrated pilot plant testing of the proposed new circuit in 1981. The pilot plant incorporated the Low-contaminant Jarosite Process, and a new two-stage zinc dust purification procedure. In 1985, approval was granted for a major modemisation program which involved the complete replacement of most of the leaching and purification plants, and substantial improvements to the residue treatment plant. Construction of the first of the new plant sections, Strong Acid Leaching, commenced in 1986. This paper describes briefly the modernisation program itself, and the current method of zinc production at the PMEZ plant. The new plant sections comprise a Strong Acid Leach stage to improve lead residue grade; a Preneutralisation stage to reduce metal losses in jarosite; new filtration stages for both jarosite and lead residue; new Neutral Leach and Weak Acid Leach stages to replace old equipment; a new Solution Purification stage to replace the use of organic reagents to remove cobalt; and a new Gypsum Removal stage to cool the solution before electrolysis. At the completion of the modernisation program, only the electrolytic cellhouse remains of the early plant sections.

Jan 1, 1993

Adsorption isotherms, zeta potential and coagulation techniques have been used to exa- mine the mechanism of metal activation on SiO2 and ZnS surfaces. The importance of surface nucleation or precipitation of metal hydroxide coatings is'established and identified-by characteristic charge reversal patterns. The significance of surface coatings in sulphide and non-sulphide flotation is discussed.

Jan 1, 1973

The theme at this yearÆs AusIMM New Leaders Conference in Ballarat was æThe Minerals Industry û Future Directions for New LeadersÆ. There was a strong focus on the recruitment and retention of trained and skilled graduates and new professionals into the mining profession. This paper highlights some of the key findings and discussion points from the New Leaders Conference. While some of the main causes of the decline in attracting new geoscientists to the mining industry have been identified, there still remains a lack of accountability among a number of Australian mining companies. Some of the factors identified that are driving new graduates away from the industry include; the social and geographical isolation, the long hours in challenging conditions and a difficulty in obtaining work straight out of University. Often there appears to be no clear opportunities within companies for career development and advancement. The opinion also still persists that the mining industry is lagging behind in both environmental and technical developments, which makes entry to the industry unattractive. Solutions that some of the large players in the Australian mining industry are implementing to help reverse the trend include targeted marketing of the lifestyle, money, freedom and travel offered in the mining industry, the development of graduate recruitment programmes and much more emphasis on the quality and reputation of the companies themselves. Incentives to attract families have also been significant in attracting and retaining employees whom otherwise would have left the workforce. However, more still needs to be done to completely reverse this trend and the mining industry needs to continue to be proactive in marketing itself as a desirable employer and career choice option for students and new professionals.

Jan 1, 2004

This paper refers to the open cut mining practice developed at Western Mining Corporation's Kalgoorlie Gold Operations (K.G.O.). Mining activity was centred attwo areas, namely W.M.C.'s Siberia "Sand King" and"Missouri" open cuts plus W.M.C.'s "Great Boulder" and K.M.A.'s "Horshoe" and "Morrison -Hannan's Star" open cuts in Fimiston.Kalgoorlie Gold Operations was set up initially to look after W.M.C.'s open cut interests in and about the Kalgoorlie area. The first mine commenced was, the Sand King open cut, approx 75 km NW of Kalgoorlie. it was here that the requirement for a highly selective form of mining first became apparent.

Jan 1, 1984

This paper describes modern long-term mine scheduling and gives an example of its application. It then discusses the obstacles to the implementation of such schedules.

Sep 26, 2011

By Ono K, Oishi T

Electrochemical determination of the oxy- gen partial pressure in the Fe-0-SiO 2 ternary systems saturated with solid silica was done by measuring the activity of oxygen in a silver bath in equilibrium with the molten slags using zirconia solid electrolyte galvanic cells. From the data obtained, the activity ~Faii.st composition relations were calculated

Jan 1, 1980

By J Pan, B-J Shi, X-B Li

The granulation behavior of specularite fines which possess poor ballability was studied with limonite fines as a function of nuclei particles and adhering fines. The results show that the permeability of granules deteriorated as the ratio of specularite fines increased in the mixture, and the optimal granulation moisture content also decreased. The granulation kinetics results demonstrate that the adhering load of specularite fines increases rapidly within three minutes and then levels off. With increasing specularite fines ratio, the adhering speed is accelerated but the granulation duration needs to be longer to reach adhering balance. The microstructure of granule quasi-particles indicates that the fine limonite particles act as binders to bond together the specularite particles which are dispersed in the adhering layers. This can improve the adhering strength of the granules. Hence, the granulation behaviour of specularite fines can be improved by blending them with fine limonite ores which have high adhering capabilities.CITATION:Zhu, D-Q, Li, X-B, Pan, J and Shi, B-J, 2015. Granulation behaviour of specularite fines in ferrous sinter mixtures, in Proceedings Iron Ore 2015, pp 91–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015