Search Documents

By Shinnosuke U, Zhang HE, Qian X

In this paper it is recommended that pyrite is to be separated as froth from arsenopyrite by selective depression of arsenopyrite in strong alkaline medium (1), by oxidation with chlorinated lime (II), by co-use of chlorinated lime with sodium carbonate (III), and by modification with `L' reagent (know-how) without filtering to get rid of residual copper ions after Cu activation (IV). The corresponding principles of these (new) effective methods were briefly discussed. The artificial mixture (1:1) of pyrite and arsenopyrite could be successfully separated, and concentrates of pyrite containing 2.12 per cent (I), 7.00 per cent (II), 2.60 per cent (III) and 3.16 per cent (IV) arsenic with recovery of 90.9 per cent (1), 89.5 per cent (II), 89.0 per cent (III) and 81.4 per cent (IV) respectively can be obtained by only one flotation. Some effective precautions were suggested to improve the separation of arsenopyrite and pyrite (or other sulphides) by flotation.

Jan 1, 1993

The introduction of many new hydraulic ally and pneumatically powered impact breakers over the past few years demonstrates the growing interest in this technique of breaking rocklike material. The most practical method yet devised to increase the blow energy range of hammer type impactors without incurring weight penalities, is to cushion the impact of the hammer on the tool. This has been achieved in one impact breaker by means of replenisible fluid cushions between the tool and the hammer, and blow energies up to 27,000 joule (20,000 ft. lbs.) have been achieved. Impact rock breaking is becoming an important alternative to the use of explosives in the mining and the construction industry. The design of impactors is discussed and manufacturers data is presented for most of the machines now available. A review of the research and mechanics of breaking rocks with impactors is presented and the benefits of high energy impactors are discussed. The relative merits of three impactor design types are explored with regard to achieving high blow energy.

Jan 1, 1978

By D J. A Van Zyl, J C. Cunning

Technological advances associated with the expanded application of paste technology in underground mine backfilling are now stimulating an interest in the disposal of process tailings as paste in the surface environment. Concurrent with the development of alternative surface tailings disposal practices is the requirement to fully understand the consolidation behaviour of tailings in paste form, and to relate this understanding to the significant body of data and operating experience from decades of study of the performance of hydraulically placed tailings. One effective method for demonstrating the benefits derived from handling and placement of tailings as paste is to review tailings slurry consolidation theory from the perspective of the changes which take place in the material as it makes its transition from a loose slurry to a dense, stable deposit resulting from managed thin-layer deposition. For a typical process tailings, an example is provided which illustrates the effect which mechanical dewatering has in accelerating the consolidation process and thereby providing a range of benefits from the perspective of surface disposal. Increased rates of filling (rise), expanded use of upstream embankment construction methods and elimination of impounded surface solutions are some quantifiable benefits which can be assembled on a site-specific basis to allow for valid comparisons with more traditional approaches to tailings disposal.

Jan 1, 1998

By D Alexander

For nearly 100 years, the flotation plant metallurgist has often wondered what is happening æbeneath the frothÆ. To assist in unravelling this mystery, new technology has been developed as part of the Australian Mineral Industries Research Association (AMIRA) P9 project, to measure gas dispersion characteristics (such as gas hold-up, superficial gas velocity and bubble size) in industrial flotation cells. These measurements have been conducted in a large number of cells of different types and sizes by researchers from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. A large database has been developed and the contents of this database are described in this paper. Typical cell characterisation measurements show a wide spread in values, even in the same cell types and sizes performing similar duties. In conventional flotation cells, the typical gas hold-up values range from 3 - 20 per cent, bubble sizes range between 1 and 2 mm, and superficial gas velocity ranges from 1 to 2.5 cm/s. The ranges of cell characterisation measurements given in this paper will enable plant personnel to compare their operation to other similar types of operations from around Australia and the rest of the world, giving opportunities for further improvement to flotation plant operations.

Jan 1, 2005

o Resource production is essential for society. o Demand for resources will increase as population grows.o Resource industries are the main consumer of trained geologists.o The lead time from(1) training to productivity(2) research to resource production is measured in years.o An adequate supply of well trained geologists and successful geological research is an important agent in ensuring cost effective, adequate supply of mineral resources for society. Therefore the main beneficiary of geological education is society itself.o Society is paradoxically apathetic or antagonistic to the resource industry because (1) it represents change(2) lobby groups working for other causes have successfully moulded a bogey man image for the resource industry in the public eye.Professional training and research for resource industries consequently lack popular support. Funding is at an absurdly low level in comparison with the economic importance of resource supply.

Jan 1, 1990

By A McEwan, J Masters, C A. Jackson, A Catanzano, V Sharp, M Millen, S Rainey, S J. Spencer, G Roberts

A passive acoustic emission (AE) monitoring system has been developed and trialled on two M10000 IsaMillsTM. The analyser detects AE stress waves generated by grinding media impacts with the mill liner during mill operation. Locally propagating stress waves can be detected on the exterior liner surface using strategically mounted broadband accelerometers.The analyser has been developed into a robust commercial prototype system, and has been designed, installed and commissioned with Xstrata Technology at two mineral processing plants.A six-month field trial showed large-scale variation in AE power signature with process conditions. Analysis of the enveloped AE power output demonstrated a strong correlation with mill process conditions – more specifically grinding media relative loading, feed pulp density, feed volumetric flow rate and feed type.Placement of accelerometers along the length of the mill body provided key information on the grinding media relative deportment. The enveloped AE power detected by the mill body, discharge pipe and bearing housing sensors all captured information strongly correlated with mill operating parameters and process state.The prototype analyser demonstrates suitability as a long-term online tool for stirred mill performance monitoring, and potentially for optimisation and control, in beneficiation plants.CITATION:Jackson, C A, Spencer, S J, Masters, J, Sharp, V, McEwan, A, Rainey, S, Catanzano, A, Roberts, G and Millen, M, 2014. Monitoring of M10000 IsaMill™ process performance by passive acoustic emissions, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 241–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Zhu, J Safarian

Understanding the slag composition-structure-property relationship remains challenging due to the amorphous nature of slag melts and the difficulty of high-temperature experimental investigations. Since the CaO-Al2O3-SiO2 slag system is maybe the most important slag system for various hightemperature metallurgical process, the present research employed high-throughput molecular dynamics (MD) simulations on the entire composition region of the CaO-Al2O3-SiO2 slag system to determine physical properties like molar volume, density and diffusivity, structural properties such as distribution of different oxygen types for each simulated slag melt. The obtained slag properties result from the simulations displayed good consistency with experimental data, underscoring the reliability of the MD simulation as a novel tool to predict reasonable slag properties and to study slag behaviour from atomistic insight. The simulated results demonstrate a near-linear relationship between molar volume changes and composition, highlighting the predominant role of oxygen atoms, which is attributed to the significantly larger size of oxygen compared to other cations in the slag melts. This disparity in size leads to oxygen ions occupying most of the space in slags, thereby playing a major role in determining the overall molar volume. The simulation results of slag density revealed a decreasing trend with increased SiO2 content and identified a local minimum at constant SiO2 when Al2O3 content increases, also consistent with established slag density models. Furthermore, the simulated oxygen self-diffusion coefficients reveal a strong composition-structureproperty relationship, where an increase in CaO content enhances slag diffusivity, while a minimum in diffusivity is observed near a CaO/Al2O3 ratio of unity. The diffusivity minimum also corresponding to the local viscosity maxima, indicating effective simulation of charge compensation effects and dynamic characteristics of slag melts. The simulated distribution of oxygen types in slag — bridging oxygen (BOs), non-bridging oxygen (NBOs), free oxygen (FOs) and tricluster oxygen (TOs) — reveals a composition-dependent pattern: BOs peak near CaO/Al2O3 = 1, NBOs and FOs are abundant in CaO-rich areas with NBOs peaking near the Ca3SiO5 composition, FOs in the CaO corner, and TOs predominantly in the Al2O3 corner, highlighting the complex interplay of network formers and modifiers for the charge compensation effects on the slag’s structural properties. The successful application of MD simulations in this study paves the way for a powerful approach to explore the complex relationships in multicomponent slag systems and bridges the gap between mathematics modelling and experimental observations in high-temperature metallurgical processes.

Aug 21, 2024

By Smith CB, Boxer GL

The Argyle diamond deposits in the East Kimberley were found as a result of a long term exploration programme, begun in 1972 by the Kalumburu Joint Venture (KJV), to search for diamonds on the Kimberley craton. When CRA Exploration Pty. Limited joined the KJV in 1976, it was re-named the Ashton Joint Venture (AJV). The Kimberley craton was considered prospective by analogy with structural settings of diamondiferous kimberlites in Africa. Diamonds were found during regional drainage sampling in Smoke Creek in late 1979, which led directly to the discovery of the rich Argyle lamproite diatreme (AK1) and associated alluvial deposits of Smoke and Limestone Creeks. The diatreme intruded into quartzites, sandstones and shales of Adelaidean age, and consists predominantly of lapilli ash tuff, with minor coarse and fine ash tuffs, 'non-sandy tuff' and olivine lamproite dykes. Erosion of the diatreme has produced the alluvial deposits of Smoke Creek and Limestone Creek to the north and east. Argyle diamonds are of predominately industrial quality, and the typical diamond is a brown, irregularly shaped, frosted, heavily resorbed form with abundant graphite inclusions, well developed etch channels and prominent hexagonal surface depressions. The pre-feasibility evaluation of AK1 comprised diamond drilling, surface and underground sampling, metallurgical sampling, marketing studies and ore reserve estimation. The proven AK1 ore reserve is 61Mtonne at 6.8ct/tonne. Evaluation of the alluvial deposits gave results of Upper Smoke Creek, 580 000 tonne at 4.6ct/tonne and Limestone Creek, 1.7Mtonne at 3.5ct/tonne. Commercial production from the two alluvial deposits began in 1983 with production for the year reaching 6.2 Mct. Mining of the alluvial deposits at three to five Mct/year is proposed to continue until the start of mining of the AK1 deposit in late 1985 or early 1986 at which time a new processing plant and associated infra- structure will have been constructed adjacent to the AKl deposit in the Limestone Creek area. Production is planned at three Mtonne/year, producing 25Mct/year, which will make Western Australia the largest producer of natural diamond (by weight) in the world.

Jan 1, 1984

At Yucca Mountain, USA, a tunnel is being built according to nuclear quality standards. It has proved possible to meet very high quality demands while at the same time achieving high advance rates. To be able to do this, routines on how to record and store quality related information have been established. This has meant that a new philosophy has entered the tunnelling industry. Especially for nuclear waste projects, of which Yucca Mountain is one of the first ones to be built, the experiences made and the quality assurance program established will be of great importance for future projects. The paper gives examples of what the Nuclear Quality Assurance system has meant in practice for the tunnelling at Yucca Mountain. And, it also explains why a non-grouted bolt, Super Swellex-, was chosen for long-term reinforcement in the tunnels which might host nuclear waste for thousands of years.

Jan 1, 1999

By Hikosaka A, Chiba A

In a fundamental study of the physical chemistry of steelmaking slag, equilibra bet- ween hydrogen-water vapour gas mixtures and liquid slags contained in solid iron crucibles have been measured for four binary slags, FetO-CaO, FetO-Si02, FetO-TiO2 and FetO-Al203 at 14000C. From the data, the activity of iron oxide and the ratio of ferrous and ferric ions (A = Fe3+/Fe2+) were calculated for the slag composition. The best ionic model is found to be that based on regular solution of cations. The oxygen distribution between slag and metal is quantitatively expressed by this model over a wide range of slag composition.

Jan 1, 1980

The Coal Section of the Geological Survey of Queensland was formed in 1950 to plan and supervise systematic diamond drilling programmes to investigate the State's coal resources. For the first 15 years these programmes were con- fined to the established coalfields to prove reserves of coal suitable for steam raising for power generation. Adequate reserves were del- ineated during this period to provide coal for the operating lives of new power stations at Ipswich and Collinsville. Later exploration was aimed at a regional appraisal of coal mea- sure stratigraphy, particularly in the Bowen and Galilee Basins. This was followed, in some areas, by drilling to prove reserves to indic- ated status. Parameters were developed to allow a uniform approach to the estimation of reserves. Coal quality is evaluated in terms of potential utilization of coal. Reserves defined by exploration companies are assessed, and combined with reserves from Departmental drilling into a general table. Total reserves in situ amount to 9 962 million tonnes of coking coal and 7 333 million tonnes of non-coking coal. Approximately 20 per cent of coking and 40 per cent of non-coking coal were proved as a direct result of Geological Survey drilling programmes. Further explor- ation is planned for the Bowen and Galilee Bas- ins and may extend to the Surat Basin.

Jan 1, 1977

The Middleback Ranges are a series of parallel northsouth ridges on the eastern side of the Eyre Peninsula, South Australia, about 20 miles inland from the Spencer Gulf, as shown in Fig. 1. They extend for some 20 miles across the centre of the County of York. North of them, on the same line of strike, in, the County of Manchester, is a disconnected series of lesser which ends in the Iron Monarch-Iron Knob ridge, the principal iron ore locality. These ridges are referred to in the following pages as an integral part of the Middleback Ranges.The deposits of hematite which outcrop in these ranges (Fig. 1) form the most important group of iron ore bodies in Australia, and are exploited by the Broken Hill Proprietary Company. The largest of them is the Iron Monarch (Fig. 6) .H: The next largest are the Iron Duke, the Iron Prince and Iron Baron. The Iron Knob, Iron Duchess, the North and South Iron Knights, Iron Queen, and the small body south of it, the Kimba Lease, and the deposits in the Cook's and Ash Leases, are all smaller.Numerous small lens-like bodies of hematite occur throughout the ridges, but are not of sufficient size to be of commercial use. At present only the Iron Monarch and the Iron Prince bodies are being worked. The Iron Knob was quarried previously, but its remaining supply is held in reserve.*Published by permission of the Council for Scientific and Industrial Research.

Jan 1, 1936

By L C. P J Fonteneau, B Godel, E R. Ramanaidou

The Hamersley Province in Western Australia hosts large iron ore deposits. Each deposit displays various iron ore types that were defined on their metallurgical properties, especially in terms of porosity and mineralogy. Conventional porosity and mineralogy information on iron ore types are provided on 2D thin sections using automated image analysis with scanning electron microscopy (SEM)-based techniques combined with chemical analyses. However these techniques cannot accurately quantify the 3D porosity. High-resolution X-ray computed tomography (HRXCT) is a non-destructive technique providing a 3D image of the sample with a resolution close to 0.5 - 0.7 ¦m for samples size of up to few centimetres in length. 3D image analysis using customised algorithms now provide accurate quantitative porosity and mineralogy of iron ore types.CITATION:Fonteneau, L C P J, Godel, B and Ramanaidou, E R, 2013. Application of high-resolution x-ray computed tomography to iron ore characterisation, in Proceedings Iron Ore 2013 , pp 243-250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Shugen T

Due to the increase of passenger traffic, a new station is proposed which is about 6.8km from south station. An underground connection line is under feasibility study for connecting these two stations in order to avoid the in- terference with surface traffic. In this paper the traffic condi- tion and the geological formation along the planned route will be described and analysed. Different methods of con struction have been proposed and dis- cussed such as shield method, slurry wall method etc. In this paper compari- sons are made among these methods and advantages and disadvantages given. The authors proposal to construct this connection line by NATM raise wide

Jan 1, 1987

By S Jeon, K Haga, A Shibayama, L Godirilwe, C B. Tabelin, I Park, A Buronov

Open pit/underground mining and mineral processing can generate large amounts of waste that contains sulfide-type minerals such as pyrite (FeS2), and it can produce acid mine drainage (AMD) when exposed to oxygen and water. This highly acidic wastewater contains heavy metals and this is one of the most serious environmental issues after mining operations taking several decades to completely remediate with high costs. For green mining, the present study focused on the development of a recovery technique for gold from an eco-friendly solvent, thiosulfate, by utilising mine wastes, tailings. First, gold recovery experiments in ammonium thiosulfate system were carried out using model samples representatively present in tailings (ie SiO2, Al2O3, FeS2, Fe2O3, and Fe3O4). The results showed that gold recoveries were negligible when using Al2O3, SiO2, Fe2O3, and Fe3O4 while pyrite shows a recovery efficiency three-fold as high as the maximum recovery efficiency when using others. Subsequently, the study also addressed the identification of the recovery mechanisms and post-recover process. The results indicate that tailings can be sufficiently utilised for gold recovery in the hydrometallurgy process and a further sustainable process can be established.

Sep 1, 2024

By R Castroviejo, F Segundo, C Brea, J-C Catalina, H-J Bernhardt

Optical microscopy is a basic but still indispensable tool for examining mineral parageneses in ores. The design and concepts behind the reflected light ore microscope have obviously not been subject to spectacular technical evolutions in the last decades. However, digital imaging capabilities have opened new and stimulating perspectives for automated mineral identification. Recent works in developing multispectral image analysis (Pirard, 2004) have demonstrated its superior potential with respect to conventional colour imaging, but at the same time reconciliation with spectroscopic databases such as the Quantitative Data File III (Criddle and Stanley, 1993) still needs a more in-depth investigation as well as the possibility to extend both imaging and spectroscopy into the near infrared domain. In this paper, the authors present results gained from multispectral imaging in the range between 400 and 1000 nm together with spectrophotometric data from the QDFIII database, with an emphasis on minerals that cannot be easily distinguished in the visible spectrum.

Jan 1, 2008

By Vidalinc, Raffoux

Longwall faces producing in the order of 20,000 tons per day of raw coal are presently running in the Houilleres du Bassin de Lorraine of Charbonnages de France. Production levels of twice that level pose some technical and economic problems of coal cutting, ventilation, coal and equipment transportation in the.face and from the face to the sur- face. The peak productions of the equipment in use today, the results of trials with new equipment, the utili- sation of forecasting models (some in the form of software), allow us to fo- resee feasable technical solutions to these problems. They will first be considered in the best possible context (thick- ness, dip, non gassy, soft coal, good strata, no faults). This will give. the necessary conditions to reach daily output'of that level. A sensitivity analysis of these- figures to the effective natural con- ditions will then be undertaken and the implication of such a project on health and safety (dust, climate ...) will be carefully considered. A concise technical and econo- mical approach will permit us to fore- cast the economical interferences of such production units and specially the consequences of sudden variations of the output (downtimes, failures, etc). From this investigation, goals for technological development and re- search areas will be outlined to be able to reach this production target in the XXIst century.

Jan 1, 1988

By L Smith, R Beckie

Controls on environmental loading from acid rock drainage (ARD) are not well understood in waste rock material. In particular, relationships between subsurface flow and the timing, duration, and intensity of leaching of metals and acidity from waste rock dumps remain ill defined. This study investigates field-scale relationships between subsurface flow processes and geochemical processes in unsaturated waste rock. A 12-metre tall, unsaturated waste rock pile, constructed in 1994, was deconstructed and sampled at Key Lake, Saskatchewan, Canada, during the summer of 2000. A detailed sampling methodology was developed to characterise physical and chemical properties of waste rock material within the waste rock pile. Physical properties were characterised by measuring soil-water suction, volumetric water content, and grain-size distribution at 60 random locations within the pile and grain-size distribution at 20 grid locations within the pile. Attempts to develop a field-based soil water characteristic curve from physical field-data failed due to spatial variability and hysteresis of waste rock properties. As a result, grain-size distribution was used as a relative measure of subsurface flow. Paste pH, pore-water geochemistry, mineralogy, and water-soluble extraction results were used to characterise geochemical processes and sulfide oxidation at each of the 20 grid locations. Geochemical characterisation results demonstrated the preferential weathering of marcasite relative to pyrite and chalcopyrite. Dolomite was the main buffering carbonate mineral. Gyspum, jarosite and iron oxyhydroxides were the main secondary minerals. Pore-waters contained up to 800, 11.7, and 6 mMolar (78 000, 690, 1400 mg/L, respectively) of sulfate, nickel, and uranium, respectively, suggesting significant weathering has occurred. Measures of weathering indicators show no discernable correlation with grain-size distribution nor do they show any spatial relationship within the sampled grid. Reasons for this may include limited duration of waste rock exposure to weathering and development of fluid flow-paths, and limitations of characterisation methods used. Indeed, six years may not be long enough for weathering patterns to develop due to fluid flow-paths in this unsaturated waste rock pile.

Jan 1, 2003

By C J. Unger, A M. Lechner, A Walton, V Glenn, M Edraki, D R. Mulligan

In Australia, responsibility for abandoned mines can be unclear. With a few exceptions, state and territory governments have become responsible for abandoned mines on Crown land and private landholders are responsible for abandoned mines on freehold land. Abandoned mines pose risks and opportunities across the full suite of sustainability themes (environmental, human health and safety, socio-economic and community development) after mining ceases.Across Australia, there are more than 50 000 abandoned mines recorded, ranging in size from individual shafts to large polluting open cut mines. Addressing the safety and environmental impacts of these sites, as well as the socio-economic development opportunities of significant rehabilitation projects, requires the implementation of effective policies and programs. Qualitatively defined graded scales or ‘rubrics’ have been used for many years in student assessment and increasingly in the performance assessment of other sectors (Davidson, 2005). While risk-based maturity models have been used for safety prioritisation (Westrum, 1993; Hudson, 2007; DRET, 2008; Hancock, 2010) and evaluation of organisational development (Esteves et al, 2010), this paper is the first to adapt maturity models for the evaluation of abandoned mine rehabilitation programs in Australia.In this paper, we used indicators based on the national policy for abandoned mines to assess the maturity of abandoned mine programs. Fourteen elements of maturity were identified (Unger et al, 2012) under the five chapters of the national policy for abandoned mines (MCMPR and MCA, 2010). Jurisdictions were then evaluated and ranked on their maturity on the basis of information that was web-accessible. Information transparency of abandoned mines policies and programs is in itself one element of the maturity chart. Each jurisdiction in Australia was compared with one another and with a Canadian jurisdiction; the British Columbia (BC) Crown Contaminated Sites Program (CCSP), which represents leading practice (Unger, 2009; Unger et al, 2012).Our research found that in some jurisdictions in Australia there is little or no information on abandoned mine programs or individual abandoned mine sites on government websites, while other jurisdictions provided very detailed program information on planning, funding and implementation. Each jurisdiction in Australia, for which web-based information was available, had some elements where they were more mature than other Australian jurisdictions. For some elements, maturity ranked equivalent to the BC CCSP, but most Australian jurisdictions were less mature. There was only one element where a single Australian jurisdiction ranked higher than the BC program in maturity. Legacy mine policies, programs, priorities and funding information via departmental websites are easier to find in some jurisdictions, indicating progression toward greater transparency and more mature programs. A systematic approach to monitoring and evaluating abandoned mines programs is essential for accountability as it can demonstrate liability reduction over time and continual improvement. The maturity model approach can provide both a measure of progress over time as well as a tool to support the implementation of the national policy for abandoned mines (MCMPR and MCA, 2010).CITATION:Unger, C J, Lechner, A M, Walton, A, Glenn, V, Edraki, M and Mulligan, D R, 2014. Maturity of jurisdictional abandoned mine programs in Australia based on web-accessible information, in Proceedings Life-of-Mine 2014 , pp 467–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Kruse JW, Kjar AR

Recently there has been increased recognition o'f the cost savings that can be achieved by the greater use of offsite preassembly for the construction of industrial plants. Preassembly is a method of construction which involves considerable offsite assembly of complete sections of an industrial plant in established fabrication shops. The preassemblies are transported to the plant site, often by large and oversize transport systems where they are set on prepared foundations, finished and interconnected to other sections of the plant as required. The concept of preassembly is not new, but widespread interest has been shown because site construction costs in all parts of the world have increased rapidly and often at a greater rate than in established fabrication areas. Particular interest has be focused on remote, isolated and inhospitable plant site locations. These areas require the import of skilled labour, the payment of high labour rate premiums and the development of infrastructure to support the workforce for the duration of the construction period.

Jan 1, 1983