Search Documents

By Ovchinnikov YN, Novikov VS, Spirin NA, Babushkin NM, Mysik AF, Shcherbatskii VB, Kukarkin AS

Laboratory investigations were carried out to determine the resistance coefficient of the flow through beds irrigated with wetting and non-wetting liquids. A formula was obtained which may be used to evaluate the resistance of the irrigated packing. Quantitative investigations were also carried out on operating furnaces at Magnitogorsk. Continuous measurements of the lower pressure drops were made under different furnace conditions. Pressures were measured in the tuyere space and the bosh region. A significant transient behaviour of the pressure drop was observed in the irrigated zone as a function of the accumulation of the liquid phase in the bosh region as smelting progressed. Additionally, transient processes were also investigated in the upper furnace zones. The basic cause of the transient behaviour was shown to be the irregularity of burden descent caused by the casting cycle. It was shown that the rate of burden descent between consecutive casts reflects fairly accurately the accumulation and drainage of the liquid products as a result of which heat transfer, reduction and aerodynamic processes assume transient character. In practically all cases of casting a decrease in blast pressure and that over the furnace height of 0.2 kg/cm2 was observed. The analyses of radial gas composition at the stock line showed that compositional variations connected with the casting cycle are most pronounced in the central and peripheral regions, whilst in the intermediate regions the conditions are relatively stable. Calculations show that as casting progresses there is a decrease in the gas flow rate at the periphery and an increase in the centre of the furnace. The transient nature of the aerodynamic processes in packings revealed the existence of an appreciable reserve capacity. Elimination of transience was tested on the furnace at Magnitogorsk and improved operating and economical furnace parameters obtained.

Jan 1, 1975

By Reilly L, Worner H. K

The EnvIRONment process has been developed to treat steel works dust and organic wastes simultaneously. A pelletised feed is fed into a special DC electric furnace, the pellets becoming immersed in a molten slag above a carbon saturated bath. The iron oxide in the pellets is reduced and carburised whilst the organics are broken down to carbon monoxide, carbon dioxide, hydrogen and water vapour. Volatile metals are vapourised and collected in the baghouse. Over two years of trials in a 100 kg DC electric are furnace has brought the process to the stage where it is ready for commercialisation.

Jan 1, 1995

By L Cooper, J Sharma, M J. Hendry

Thick clay tills below potash mine tailings and brine ponds are important natural barriers protecting fresh water aquifers in Saskatchewan. Centrifuge modelling was applied to assess geochemical processes and impacts of dilute brine (0.1 M NaCl) migration through clay till core samples obtained from non saline, unoxidised clay till at a mine site. At accelerated gravity of 876 + g, during each day of centrifuge modelling, flow driven through a 52 mm length core simulated transport through a 45 m thick clay over ~2100 years. Hydraulic conductivity, monitored continuously before and during brine permeation, was low and relatively constant (8.5 + 10-12 m/s), confirming that confining stresses prevent permeability increase. Core density and porosity measurements confirmed that reactive transport occurred under realistic in situ conditions. Breakthrough (defined by C/C0 = 0.5) of non-reactive Cl- occurred at 25 days. The slight delay for Na+ breakthrough, associated with small increases in Ca2+ and Mg2+ concentrations in the effluent were attributed to ion exchange, but carbonate reactions were relatively unimportant. Cation exchange analysis of core samples was inconclusive without corrections for porewater Na+ and carbonate dissolution. Geochemical processes that were observed during centrifuge modelling were successfully simulated using the 1D geochemical transport code PHREEQC. Solute transport was dominated by diffusion with limited ion exchange to delay Na+ migration. Brine would not break through a 45 m thick clay for tens of thousands of years. Based on these findings, the thick clay till at this site, if laterally extensive and undisturbed by drilling activity, is likely to act as an effective natural barrier to vertical brine migration over the long term.

Jan 1, 2003

The operation of quarries for the production of crushed stone and aggregates, depends heavily on rock blasting efficiency, which usually represents a major share of total production costs. After investigating the causes of this situation, a series of technical aspects have been detected, and they are described for the purpose of contributing to the minimization of costs, which also reduces the effects of blasting on the environment. Utilization of empirical design methods, of inadequate explosive types, and of erroneous drilling pauems with respect to rock properties, are the main factors to be corrected, as a consequence of poor engineering criteria, with scarce use of computational methods and field instrumentation. Several concepts of blasting optimization are pointed out, and their application to industrial operations in a Portuguese limestone quarry indicated clear trends for the reduction of production costs, as well as some of the deleterious consequences of blasting on the environment.

Jan 1, 1990

By C Li, K McDonald an, T Nicholson, C Brown

The relative reactivities of chars prepared from different coal samples at temperatures in the range 500 to 1150¦C were determined by measuring the rates of metallisation of a standard ilmenite concentrate. The results have been interpreted in relation to different measured physical and chemical properties of the chars. Char reactivities were found to correlate with the maximum specific surface area (SSA) of the chars, obtained from plots of SSA versus temperature. Weathering of coal samples gave higher reactivities which correlated with higher SSAs. Experiments using recycled chars showed that the high internal SSAs developed during earlier reduction reactions provide no benefit in terms of increased metallisations. The important role of char hydrogen contents in controlling low temperature metallisation rates was demonstrated. Chars prepared from different rank coals had the same hydrogen content when prepared at the same temperature. Ilmenite metallisation rates had a linear dependence on the hydrogen content of the chars. Large differences in the slopes of the metallisation versus H2 content curves for different chars were interpreted in terms of SSA variations and catalysis of the gas reactions by dispersed metallic iron particles in the chars. A simple test based on magnetic separation of the char was shown to give an indication of enhanced reactivity due to contained metallic iron.

Jan 1, 2001

By Shrivastava P, Humphreys M, Guibal D, Deraisme J

Customer requirements concerning the final products of iron mines are extremely stringent. Because of this, there is an ever-increasing need for mine operators to monitor and strictly control the quality of their product. This quality, as measured by the stockpile grade variability, is the result of a very complex process, where natural characteristics (the orebody and its geology) are transformed through the mining technique (open pit, shovel and truck fleet, blending into stockpile). The only way to reproduce and hence to control the variability of such a system, which is composed of several interactive sub-processes, is by simulation. A complete simulation of a Hamersley Iron Pty Ltd (HI) ore deposit has been undertaken to forecast the impact and cost of various mining methods, mining schedules and product stockpile sizes on variability of chemical and physical characteristics of the products. The mining simulation was made on a conditionally simulated orebody. On a range of criteria, the simulation was considered to fulfil the objectives set and was a valuable aid to analysis of product grade variability, operating and capital costs, selection of equipment, mine scheduling and setting of product grade targets.

Jan 1, 1994

By N A. S Webster

The reaction sequences involved in the formation of iron ore sinter phases were determined using in situ synchrotron-based X-ray diffraction. Experiments were carried out using a synthetic sinter mixture containing 77.36 per cent Fe2O314.08 per cent CaO, 3.56 per cent Si.O2 and 5.00 per cent Al2O3 corresponding to a basicity of ~4. The alumina content represents the upper level of alumina concentrations measured in phases formed in industrially produced plant sinter. Data were collected during heating of the sample to 1350°C under an atmosphere of 0.5 per cent O2 in N2, equivalent to an oxygen partial pressure of 5 × 10-3 atm. This temperature was sufficientto ensure melting. Data were also collected on cooling of the sample back to room temperature to examine recrystallisation of phases from the melt.Results showed the sequence of reactions initially involved the formation of calcium ferrite phases C2F and CF. These subsequently reacted with the silica and haematite leading to the solid state formation of SFCA and SFCA-1. SFCA and SFCA-1 were the last phases to form in the system and were both stable up to ~1260°C. Above ~1260°C, melting of the SFCA phases and reduction of the remaining haematite occurred producing the assemblage magnetite + melt.During cooling, both SFCA phase types recrystallised from the melt initially coexisting with magnetite until secondary haematite formed. This is the fi rst study to demonstrate that both SFCA and SFCA-1 are precipitated from the melt during cooling of iron ore sinter. Future work will extend the range of compositions studied to examine the effect of basicity and alumina concentration on the phase assemblages as a function of temperature and oxygen partial pressure.

Jul 11, 2011

By C Preston, T Williams, D Roy

The easiest way to mine valuable orebodies is through the use of explosives and well-planned blasting layouts that produce fragmentation profiles designed specifically for conveyance equipment in underground mines. The design of blasting patterns is specific to not only the explosives being used but also the rock or ore type being fragmented. Many blasting designs are based solely on the experience of those developed for similar orebodies in terms of properties and orientation or individuals that have some blasting experience.The primary technical objective of this paper is to outline a unique methodology for determining underground blasting methodologies (developing specific blasting parameters) commensurate with explosive energies and rock/ore equations of state for a narrow-vein gold property located in Northern Quebec and for underground mines in general.The procedures developed are to define the desired fragmentation specification so that a specific thermodynamic break is generated, taking into account powder factor, energy factor, tonnages, explosive energies and distribution along with blasthole diameter and orebody orientation for a specific set of explosive and dynamic rock/ore properties. Determining dynamic modulus values for the ore using seismic sensors to measure P- and S-wave velocities, the aforementioned parameters will be utilised to set the design constraints to maximise recovery and minimise overbreak and dilution.New underground blasting software (AEGIS) will use thermodynamic break in conjunction with defined fragmentation profiles to create an array of blasting parameters used to design and plan ring layouts. This software will also allow mining planners, prior to drilling and loading a production blast, to appraise future intended blasting patterns to minimise the potential of diluting ore with host rock and the likelihood of damaging mine support structures.CITATION:Roy, D, Williams, T and Preston, C, 2015. Underground stope drill and blast designs optimisation program, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 137–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Szymanski J, Planeta S

For many hard rock mines with near surface deposits, the surface crown pillars form the first line of protection for the immediate underground workings. Underground stopes are typically contained by crown pillar, which protects the level above, rib pillars, and a sill pillar through which the ore collection system is cut. This paper discusses the mining of these pillars, with particular emphasis on the overall stability of the mined out upper part of the mine areas. An area of interest is located in the Canadian Shield, where the mining has progressed below four thousand foot level in the ultramafic high grade sulphide type of orebody.

Jan 1, 1995

By Lorenzen L

In South Africa, as in many other countries, the young engineering graduate is promoted quite soon to a management position where he uses less technical skills and more people-oriented skills. In the standard undergraduate curriculum for engineering, little attention is paid to the non-technical issues of the profession. An undergraduate course in management techniques cannot be a substitute for a MBA or Masters degree in engineering management, but can at least create an awareness of the practical problems facing the engineering manager. The aim of this paper is to provide an outline of such a course structure at the University of Stellenbosch. A survey is also presented on management training in the South African and Australian mineral industries. Feedback from students and graduates indicates that the fresh graduate does not fully appreciate the value of such a course until he/she achieves a position of responsibility after two or three years. Nevertheless, the management course appears to be successful in widening the perspectives of the engineer. As explained frequently in management journals, the technically oriented person (the engineer) has a convergent thought pattern, which could be in conflict with the more divergent thought pattern of the top, personnel or marketing manager. It becomes increasingly imperative for the young minerals engineer to be externally oriented instead of the traditional internal focus of engineering. The engineer should not only be aware of environmental issues in the technical design and operation of plants, but should also understand the inter-relationship between public relations, political pressures and environmental perceptions vis-d-vis technical facts.

Jan 1, 1993

By McAuley T. J

Computer software is an integral part of mining operations today with many sites using six or more software packages on a daily basis. However, the use of these different programs generates the need for substantial staff training. The current trend toward large integrated packages to solve this problem is counter-productive because the relatively small companies producing specialised mining software do not have the resources to develop quality software with all the required features. Software standards are being proposed by various parties but recent history indicates these will be unsuccessful. An alternative approach is suggested using the various standards which have been developed for the Windows operating system.

Jan 1, 1995

By J Rutter, E Amini, D La Rosa, N Beaton, M Scott, F Faramarz, L Keeney

Anglo American’s Los Bronces copper mine in Chile has been conducting detailed assessments investigating value adding options for their asset. The mine has conducted several detailed Mine-to- Mill and Grade Engineering studies to investigate increased throughput and head grade and to quantifying the impact of these approaches across the life of mine. CRC ORE has two key technologies namely Grade Engineering and the Integrated Extraction Simulator. These two technology suites have been combined to understand the technological landscape and associated value drivers suitable for application at Los Bronces. Detailed ore characterisation test work was conducted to:  measure and spatially model the propensity of ores to naturally deport and  develop customised blast models for Mine-to-Mill and Grade Engineering evaluation The outputs of this work were utilised to develop a block model populated with a range on new Grade Engineering and blasting parameters suitable for scenario analysis. To facilitate scenario analysis a high-fidelity value chain model of the Los Bronces operation from blasting to concentrate production was built in IES. IES was combined with sophisticated analytical tools such as Neural Networks to develop and reconcile a fully integrated value chain. The value chain model made it possible to simulate in IES all available blocks in the block model to predict throughput and grade changes for different strategic scenarios. The scenario analysis was run across 24 strategic combinations of Mine-to-Mill and Grade Engineering and comprised several million simulations. The scenarios investigated each technology independently and jointly to provide an attributed block model that can feed forward into technoeconomic modelling to determine optimal execution strategies for the mine. This paper presents the first published study combining Grade Engineering and IES to provide mass simulation capability to investigate strategic options for a mining asset.

Nov 10, 2020

By M Yvon, S Parkes, K P. Galvin, P Wang

Mineral liberation is critical to maximise the grade and recovery of nickel, however this objective is challenged considerably by the poor flotation kinetics, especially that of ultrafine particles (Kelebek and Tukel, 2018; Multani and Waters, 2019). High recoveries demand long cell residence times and hence a large flotation capital expenditure (Wills and Finch, 2016). However, this leads to excessive entrainment of gangue minerals, thus negating efforts to depress its recovery. This study aimed to investigate new hydrodynamic approaches to improve nickel flotation, focusing primarily on unrecovered nickel from a Western Australian tailings stream. Mechanical cell flotation experiments were conducted to understand the flotation kinetics, covering different size ranges. A novel Reflux Flotation Cell (RFC) was also used to improve the nickel recovery and reject the silicates. Future work aimed at applying the RFC to different size portions is also outlined.

Aug 24, 2022

By S G. Gemell

"The financial model is an integral component of any project evaluation based on mineral resources, ore reserves and (at least internally) exploration targets. Given the unity of purpose for preparing financial models for project evaluation purposes, the diversity of both format and content of the finalised models is surprising. Many models are prepared by staff or consultants who are comfortable with a particular format that may be used for other purposes, such as budget preparation or financial reporting. It is natural in these situations that the practitioner will take these models and adapt them to the purpose. The end result may or may not succeed in providing a clear, accurate and sufficiently detailed view of the project’s economic viability.When preparing a model, the practitioner should be cognisant of the interpretation and review, or audit, process. The auditor may be a consultant or employee of a bank, potential equity provider or of the project sponsor itself. Depending upon the scale of the project and the level of participation of the entity that the auditor represents, the financial model will be interrogated more or less rigorously. In any event, the end user will require the model to permit easy change of inputs and will wish to confirm that such change is appropriately and thoroughly transmitted throughout.Accordingly, there are some ‘dos and don’ts’ that can be readily applied in the creation of the financial model that will greatly assist the end user, not just in the change of inputs, but also in reviewing the model’s integrity. The less time and effort required by an auditor in this regard is reflected directly in the cost of the review process.CITATION:Gemell, S G, 2016. Financial modelling with the auditor in mind, in Proceedings Project Evaluation 2016, pp 172–180 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Johnson N. W, Quast K. B

Over the years there have been occasional references in the literature to the activating effect of cyanide in galena flotation with xanthates. These have usually been associated with the processing of lead-zinc or copper-lead-zinc ores. Bubble contact curves for the pure galena-xanthate system show a flotation edge at pH 10.4 independent of sodium cyanide concentration which was thought due to hydroxyl ion, not cyanide ion.Flotation tests were conducted on samples of Mount Isa lead-zinc ore using varying concentrations of sodium ethyl xanthate and sodium cyanide. At low collector concentrations, galena recovery kinetics improved with sodium cyanide addition, and the higher the cyanide concentration, the higher the galena recovery rate. At higher collector concentrations, galena recovery rate was independent of sodium cyanide addition.For a given collector addition, the lead grade-recovery curve shifted to an improved position with increasing sodium cyanide level. For the same recovery there was an increase in the lead grade with increased sodium cyanide addition, and this increase was most dramatic at high sodium cyanide concentrations.The presence of sodium cyanide during the grinding of Mount Isa ore caused surface passivation of the iron sulphides and possibly the sphalerite.These sulphides, therefore, reacted with less of the oxygen present in the pulp, hence more oxygen was directed to the surface of the galena. This resulted in an enhancement in the total amount of xanthate adsorbed on the galena that is reflected in the improved flotation response of that mineral.

Jan 1, 1990

Base metal skarns have provided most of South KoreaÆs Pb-Zn production since the end of the Korean War, with the bulk of production coming from the Yeonwha group of mines. Currently only the Kumho Zn-Pb mine remains in production, while magnetite skarns are mined as iron ore at the old Yomisan and Ulsan base metal deposits. Base metal skarns within Korea fall into two groups; those hosted in Cambro-Ordovician limestone sequences, situated mainly in sub-basins in the northeast of the peninsula and those hosted within carbonate volcaniclastics of the Cretaceous Gyeongsang Basin, in the southeast. Sulphide mineralisation is dominated by sphalerite, lesser galena, arsenopyrite and pyrrhotite, with subordinate chalcopyrite and molybdenite with Ag-Co credits. Skarns are composed of pyroxene-clinopyroxene-garnet-carbonate-quartz and magnetite, grading into silica-chlorite hornfels. Most of the significant deposits display both pipe-like and stratabound morphology. In the Hwanggang district, a zoned distribution of Ordovician carbonate hosted, polymetallic Mo-W and Zn-Pb-Cu-Ag base metal deposits is observed around the margin of a Cretaceous granite intrusion. Similar polymetallic zoning is recognised in the Sangdong district, where deposits include Sangdong (W), Abisan (Au-As) and Yomisan Northwest (Zn-Mo) and Yomisan Southeast (Zn-Cu-Co), hosted in Ordovician carbonates in proximity to Cretaceous quartz porphyry intrusives. The Taebaeksan district hosts the largest deposits at the Yeonwha group of mines. Although production ceased in 1993, significant resources remain, hosted in Ordovician limestone and dolomite that have been intruded by Cretaceous quartz porphyry dykes. Deposits in the Cretaceous Gyeongsang Basin consist of bedding concordant, vertically stacked base metal skarn mineralisation at several stratigraphic horizons, connected by carbonate-base metal veins with a pipe-like geometry. Evidence such as massive sulphide layers and restricted proximal carbonates suggest mineralisation was initially partly syn-depositional, with both base metals and carbonate venting onto a lake floor, being reconstituted to skarns by later magmatic activity. Skarn mineralisation is universally closely associated with the Cretaceous Bulgugsa Series acid intrusive activity. A common intrusive-structural relationship is recognised at some deposits, with bedding plane and imbricate thrust faulting, introducing felsic intrusives as sills. These intrusions probably introduced the base metals, carbonate, boron, heat and silica, which metasomatically reconstituted the carbonate lithologies to form skarn assemblages. The Korean base metal skarn deposits are regarded as Zn-Pb chimney-manto skarns and display similarities to the Mexican manto type deposits.

Jan 1, 1999

By H Askari-Nasab, E Torkamani, M M. Badiozamani, S P. Upadhyay, M Tabesh

"Decision-making in mining is a challenging task. Optimal decisions regarding shovel and truck allocations, aligned with the optimal short-term production schedules, are crucial in keeping the operations in line with the company’s long-term objectives. In this paper, we present two main modelling components as the means to achieve near-optimal operational plans: a mixed integer linear goal programming model to allocate trucks and shovels to mining faces over a shift-by-shift basis so that operating costs are minimised and resource utilisations are maximised through the planning horizon a discrete-event simulation model to investigate the behaviour of a truck-and-shovel haulage system in the presence of uncertainty within mining operations. The goals integrated into the mathematical model are to: maximise production minimise deviations from the target head grade minimise deviations in tonnage feed to the processing plants from the desired feed minimise operating cost.The mathematical model provides shovel assignments and the target productions as an input to the discrete event simulation model while meeting the desired goals and constraints of the mining operation. We illustrate the applications of the discrete event simulation model by presenting a large-scale oil sands case study. The main contribution of this work thus far is the development, implementation and verification of a simulation model with a link to optimal short-term mine schedule and extraction sequence of mining faces, which assists in achieving a high level of mine plan compliance across short-term planning and operational planning time horizons.CITATION:Askari-Nasab, H, Upadhyay, S P, Torkamani, E, Tabesh, M and Badiozamani, M M, 2014. Simulation optimisation of mine operational plans, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 299–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By J Mavrogenes, C J. Spandler, S M. Eggins, K Worden

Major occurrences of platinum group minerals (PGM) are in crustally-contaminated, huge, layered igneous complexes (Bushveld and Stillwater) and gabbroic intrusions (Norilsk); relatively minor occurrences include arc-related æzoned Alaskan ultramaficsÆ. In terms of arc-related provenances, the recognition of alluvial PGM in river and beach deposits of southern South Island (Mitchell, 1995), in situ in the Longwoods (Cowden et al, 1990), and the ultramafic-mafic layered Greenhills Complex at Bluff (Spandler et al, 2000) raise the possibility that some economically-significant PGM deposits may exist in New Zealand. The Longwoods and Greenhills are in the Brook Street Terrane which is a remnant of a primitive intra-oceanic arc system of Late Permian-Early Triassic age. The Terrane comprises volcanogenic sequences containing plagioclase- and clinopyroxenephyric basalts, high-MgO ankaramite and dolerite dikes, trondhjemite plutons, and basaltic to andesitic volcaniclastic and sedimentary rocks. The cumulate complexes contain early-formed olivine- and clinopyroxene-rich ultramafic cumulates overlain by anorthite and hornblende-bearing gabbros. Primary (isoferroplatinum) and secondary (sperrylite) platinum group minerals are preserved in chrome-rich spinel pods in basal dunite of the Greenhills Complex. Saturation during early fractionation of primitive high-MgO magmas rather than magma mixing seems likely for the primary PGM. Together with correlative terranes in Queensland and New Caledonia, the Brooks Street Terrane is an exposed cross-section of an extensive Permo-Triassic island-arc system. Most parental magmas were primitive island-arc tholeiites, but other primary magma-types include high-MgO ankaramites and trondhjemites û the latter formed by partial melting of lower crustal clinopyroxene-rich cumulates and gabbros, respectively. The parental ankaramites fractionated to form mafic-ultramafic cumulates and primitive to evolved melts of high-Al basalt to andesite compositions (Takitimus). The Brook Street Terrane is an analogue for modern intra-oceanic islandarc systems and allows detailed study of subvolcanic arc processes.

Jan 1, 2005

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Trial ore production began at the Hilton Mine in 1987 with ore being trucked into Mount Isa for treatment at the Lead/zinc Concentrator. The expansion of output from the Hilton mine required additional concentrator capacity which led to the design and construction of the Hilton Concentrator. Systematic laboratory and Pilot Plant testwork dating back to 1968 to develop a flowsheet and reagent regime suited to the varied and generally complex mineralogy of the Hilton ore was successfully concluded with a Pilot Plant trial using a sulphoxy based sphalerite depression system in early 1988.In May 1988, a decision was made to build a 750 000 t/y concentrator with some novel technological and capital-efficient features. The Hilton Concentrator commenced operations in December 1989 reaching target grinding rates and metallurgical performance by mid-1990. Current ore treatment rate is 800 000 t/y.Lead concentrates assaying 43 - 48 per cent Pb are combined with the Lead/Zinc Concentrator lead concentrates and smelted at Mount Isa. Zinc and Low Grade Middlings (LGM) concentrates are filtered in the zinc filter plant at Isa with those from the Lead/Zinc Concentrator and then railed to Townsville for export or treatment in Australia.

Jan 1, 1993