Search Documents

The Prospect to Pipehead Tunnel is a component of the Sydney Water Board's multi-million dollar Drinking Water Quality Program to improve the quality of Sydney's potable water supply to meet revised national health guidelines. The tunnel project involves the construction of seven kilometres of 3.9 metre diameter machine bored tunnel which is to be lined with a three-metre diameter steel liner. The paper describes the fully integrated planning and design approach and management technique used to enable this major project to proceed to meet the requirements of a tight construction program.

Jan 1, 1993

The Teutonic Bore deposit lies in a major greenstone belt within the Archaean Yilgarn craton of Western Australia. It occurs towards the base of a suite of tholeiitic basalts, some 100 m above a felsic volcanic pile of rhyolitic composition. Sediments comprise a minor, albeit important, percentage of the mine stratigraphy.The deposit consists of a single, steeply dipping lens of massive sulphides totalling 1.4 million tonnes grading 4.16 per cent Cu, 16.4 per cent Zn, 1.22 per cent Pb and 203 g/t Ag. In addition, cross cutting "stringer" mineralisation in the footwall contributes a further 0.75 million tonnes at 2.38 per cent Cu, 1.92 per cent Zn and 52 g/t Ag to the mining reserves. Principal primary sulphides in massive and disseminated mineralisation are sphalerite, pyrite, chalcopyrite and galena, while minor amounts of arsenopyrite and argentiferous tetrahedrite are also present. Weathering has affected the primary mineralogy down to at least 90 m, resulting in a strongly leached oxide profile to about 85 m, overlying a thin, erratic zone of chalcocite supergene enrichment.Lateral metal zoning is marked both in massive sulphide and stringer mineralisation, with Cu/Zn ratios decreasing away from the centre of the orebody. Alteration is well developed in association with footwall stringer mineralisation, changing from a central Fe-Mg carbonate, chlorite and silica alteration zone below the massive sulphides to an outer halo of sericitisation. The spatial distribution of these minerals is patchy. Geochemically, the footwall alteration zone is characterised by central Cao, Na20 and Sr depletion (with less regular enrichment of SiO2 , Fe and MgO), surrounded by a peripheral zone of K20 enrichment.Evidence supports a classic volcanic-exhalative origin, involving submarine discharge on the flanks of a rhyolitic dome and accumulation of the massive sulphides in a local palaeotopographic depression. The sulphides overlie their feeder zone as shown by alteration and stringer mineralisation. Tholeiitic wallrocks are thought to be genetically unrelated to the mineralising solutions, although their presence as a cap over the felsic volcanics may have permitted the build up of a circulating metalliferous brine system prior to sulphide deposition.

Jan 1, 1984

By Robinson B, Ham B

Outbursts have occurred irregularly in the Collinsville Coal field since 1954 when an incident claimed seven lives. Further significant outbursts occurred in 1960, 1961, 1972 and more recently in the No. 2 mine in 1978. From the information collected over 25 years a comprehensive program to minimize the hazard of outbursts has evolved. Further developments of techniques to combat outbursts are being developed.

Jan 1, 1980

The Cadjebut Mine is located 80 km southeast of Fitzroy Crossing. Cadjebut is owned 58 per cent by BHP Minerals and 42 per cent by Billiton Australia. Cadjebut is a 'Mississippi Valley Type' (MVT) deposit. Minerals present are sphalerite, galena and marcasite in a sedimentary host of dolomite and siltstone. The ore contains few deleterious impurities and no silver. The mill was commissioned in the first half of 1988 at a rate of 320 000 tonnes per annum. An expansion in the latter half of 1989 has since increased production to 550 000 tonnes per annum. The initial geological resource at the commencement of mining was 3.8 million tonnes at 13.5 per cent Zn and 4.4 per cent Pb. There is sufficient ore left to sustain operations to 1995 at a grade of 11.2 per cent Zn and 3.9 per cent Pb. The ore from underground is stockpiled on the surface via a drift conveyor and from the stockpile is fed into a grinding circuit consisting of a SAG and ball mill. Cyclone overflow at a Pgp of 90 pm gravitates to the flotation circuit. Lead and zinc are sequentially floated to produce an 80 per cent Pb grade at 90 per cent recovery and a 61 - 62 per cent Zn grade at 96 per cent recovery. The concentrates are thickened and filtered before being trucked to the port of Wyndham 600 km away. From Wyndham the concentrates are shipped to smelters in Asia, Europe and Australia.

Jan 1, 1992

By Artmont G. J, Palmer K

Alluvial gold is an ideal exploration tracer to bedrock source and indicator of bedrock mineralisation style because (i) gold occurs in a wide range of deposit types, (ii) primary composition is sensitive to style of mineralisation, and (iii) it is a heavy resistate mineral that is readily preserved and easily sampled. In regional exploration of the Central Ranges of Irian Jaya, alluvial gold mineralogy has been applied to maximise the information return from panned concentrate sampling and to focus exploration effort. Primary gold is a solid solution of Au+Ag¦Cu¦Hg, ¦ trace Pd, Te, and Sb. In general Ag¦Hg increase and Cu decreases with inferred decreasing temperature of formation, and gold from particular mineralisation styles has signature compositions that can be used as indicators of bedrock mineralisation type. Furthermore, the abundance of alluvial gold is an indicator of the economic potential of a catchment. The convergent continental-oceanic plate geology of the Central Ranges is conducive to a wide range of mineralisation styles. Mineralogy of gold in ophiolite, skarn, porphyry, mesothermal vein and possible VHMS environments is characterised from alluvial and bedrock samples, and the use of gold mineralogy in prospecting at regional scale through prospect definition to drilling is demonstrated.

Jan 1, 1995

By J Chan, T Baumgartl, A Plante, C Peltre, P D. Erskine

Mine soils are often organic matter and carbon poor due to disturbance, topsoil stockpiling and mixing with spoil. They present an opportunity to observe the accumulation of soil carbon arising from rehabilitation or ‘green carbon’ through organic matter inputs and may be considered for carbon credits. Soil carbon is known to improve multiple soil characteristics and is viewed as an indicator of soil health.When attempting to estimate soil carbon levels in the Australian coal mining regions, both coal and black carbon (BC) need to be quantified. Coalmine soils contain coal particles that are difficult to distinguish from organic matter using standard carbon analyses. BC, a material arising from the incomplete combustion of organic matter and fossil fuels, displays some similar characteristics to coal and is ubiquitous in Australian soils due to bushfires. The presence of coal and BC complicate the determination of green carbon levels in mine soils.A method to quantify coal and BC in mine soils from the Bowen Basin using thermal analysis and multivariate curve resolution is presented. By determining BC and coal contributions it is then possible to calculate green carbon levels in rehabilitated mine soils. Calculated green carbon levels are compared with bulk density as soil quality indicators.CITATION:Chan, J, Baumgartl, T, Erskine, P D, Peltre, C and Plante, A, 2014. Distinguishing carbon fractions in coalmine rehabilitated soils, in Proceedings Life-of-Mine 2014 , pp 491–498 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

With the recent increase in the number of underground secondary sulphide dust explosions in Canada, Australia and elsewhere in massive sulphide ore mining industry, establishment of quantitative and realistic methods of analyzing the mine dust is of paramount importance. This paper examines and analyses dust samples from a mine area that has very recently experienced sulphide dust explosions. Also, it attempts to evaluate the physical and chemical characteristics of the dust. Explosibility of the dust samples was determined by quantifying the oxidation reaction of the sulphide dust particles in a 1.2 L, Lindenberg open horizontal tube furnace. Percentage sulphur', % S oxidised during ignition of a dust sample of known assay, % S and dust concentration (g/m3) were determined by the quantitative chemical analysis of SO2 gas produced during the oxidation reaction. A dust sample with high sulphur content, 22.3% S (assayed) and mean particle size 9.82 pm, was found to exhibit a low degree of oxidation compared with a sample of low sulphur content, 15.44% S and mean particle size 21.7 tcm, at the same Temperature.

Jan 1, 1988

By A J. Morrison, K Demir, J Kohmuench, K Runge, C Evans

The Eriez HydroFloat® is a flotation device capable of recovering significantly coarser and lessliberated particles than is possible using a conventional mechanical flotation cell. Originally developed for industrial and bulk mineral beneficiation, the HydroFloat® is attracting increasing interest as a means of increasing the required grind size for metalliferous ore flotation. Doing so would reduce the costs of processing complex ores, either by decreasing the energy required to grind the flotation feed or by increasing the throughput achievable with a given comminution circuit. Processing coarser particles would also result in coarser waste streams, potentially improving the mechanical and hydraulic performance of the waste dams that they are sent to. Recent work at pilot – and industrial-scale has proven the potential of the HydroFloat® technology to achieve these gains in metalliferous applications. However, in order to realise the full potential of the HydroFloat® technology, it is necessary to understand not just its performance but also the drivers for that performance. Doing so will allow the design and operation of HydroFloat® devices to be optimised for different ores and applications. For this work, a HydroFloat® pilot rig was deployed to a coppergold plant in Australia and was used to investigate the effect of stream and operating conditions for treating the tailings stream of one of the plant’s rougher flotation cells. Under each set of operating conditions, samples were taken of the HydroFloat® feed, tailings and concentrate streams, and processed to yield the grade and recovery achieved by the device. At the same time, the bubble size and bed behaviour inside the device were measured. This paper presents preliminary relationships observed between the operating conditions and the performance of the HydroFloat® cell, and thus suggests a range of possible drivers for the measured coarse particle flotation performance.

Aug 24, 2022

By M Nehring, M Kizil, P Knights, A Mousavi, F Sotoudeh

A cut-off grade is used to distinguish an economically viable block of ore from non-economical ones in mining operations. In order to obtain a high Net Present Value (NPV), a strategic and precise determination of cut-off grades (mill feed/marginal, marginal/waste) is required. In recent years, the significant depletion of feed grades and increasing mining operating costs have affected the viability of new and existing mining operations. Hence, the introduction of a pre-concentration system to process ore before sending it the main processing plant has gained increasing attention for its potential improvements in resource exploitation processes, mineral processing, energy consumption and environmental impacts. The primary potential advantage of implementing a pre-concentration system is the improvement of resource utilisation and increased reserves as a result of a reduction in cut-off grade. The objective of this paper is to present a new cut-off grade method, which can be used in the presence of a pre-concentration system for underground metalliferous mining operations. The results of this study illustrate the potential economic benefits of using a pre-concertation system prior to a mineral processing operation as a result of the reduced cut-off grade and increased NPV.

Nov 10, 2020

The New Broken Hill Consolidated Airshaft is the first major undertaking in the development of New Broken Hill Consolidated Ltd's. property, which adjoins that of The Zinc Corporation Ltd. on the latter's southern boundary.The Zinc Corporation ore-body has a southerly pitch. The Zinc Corporation's New Main Shaft is 1000 ft. north of the common boundary, and the general plan of development of the New Broken Hill Consolidated property is by driving south from this shaft on the lower levels. No downcast airway from the surface was available south of the Zinc Corporation's New Main Shaft; this shaft acts as the main downcast to the bottom of the Zinc Corporation mine, the general air flow then being northward and upward to the upcast shaft at the extreme north end of the Zinc Corporation property.Rock temperature is 920 F. at 2000 ft., increasing by 10 Fahr. each 72 ft., the rock temperature at 3000 ft. being estimated at 1060 Fahr. With the general air flow northward from the Zinc Corporation's New Main Shaft, adequate ventilation under these temperature conditions would not be practicable for any great distance south of this shaft without another main airway from the surface. Accordingly the New Broken Hill Consolidated Airshaft is being sunk at a point 1000 ft. south of the common boundary, i.e., 2000 ft. south of the Zinc Corporation's New Main Shaft, to ventilate future New Broken Hill Consolidated workings and that part of the Zinc Corporation mine between the boundary and the New Main Shaft.

Jan 1, 1940

The application of methods using large diameter down holes has become an important facet in both the development and stoping operations of mines within the Aberfoyle group. Holes of up to 98 metres (vertical) and 78 metres (inclined) have been successfully used in stoping operations. A number of rises have been developed to meet ventilation, servicing and escape-way requirements. The most ambitious rise to date has been a..vertical 93 metre long by 4.50 metre square ventilation rise. Although some early problems were experienced, the ultimate successful completion of this rise has enabled the technique to be incorporated with confidence in future mining plans. This paper summarises experience in long hole rising techniques, their evolution from the original cratering concepts, and the approach to further development of these techniques.

Jan 1, 1982

By Mitchell G. W, Purvis A. H

The Lady Loretta silver-lead-zinc deposit lies north of Mount Isa in folded and faulted Proterozoic carbonate sediments. The deposit was discovered in the late 1960's as a result of a soil geochemical survey. Subsequent surface drilling outlined mineralisation folded into a synclinal structure extending to a depth of 460 m and containing exceptionally high grades within the keel of the syncline. Pancontinental Mining Limited and Outokumpu Oy of Finland acquired the property in 1985.

Jan 1, 1988

This research is about human development and socio-economic progress of the main mining areas of Chile in the period 1990 - 2007, and especially about the positive effects that mining activity has on poverty reduction and indicators related to the Millennium Development Goals of the United Nations. The analysis is doubly interesting, if one considers that the economic and social developments in Chile, recognised and prominent among the Latin American economies and developing nations, are more evident in mining areas as Tarapacß and Antofagasta (northern Chile), which concentrated than more 70 per cent of investments and mining assets in the country. Additionally, the study concludes with methodological reflections for the evaluation of socio-economic impact in the mining industry in developing countries.

Jan 1, 2009

By R L. Brathwaite

The rocks of New Zealand can be grouped into three main elements: the Early to Mid Paleozoic Western Province, Late Paleozoic to Early Cretaceous Eastern Province, and several overlying Late Cretaceous to Cenozoic sedimentary basins. The Western and Eastern provinces were formed on or near the margin of Gondwanaland, whereas the Late Cretaceous to Cenozoic sedimentary basins developed after the separation of New Zealand from Gondwanaland in the Late Cretaceous.   The Early to Mid Paleozoic Western Province rocks are exposed in Nelson, Westland and Fiordland and include metamorphosed sandstone, mudstone, limestone, and volcanic rocks, intruded by granite batholiths and maficultramafic igneous complexes. The main associated mineral deposits are gold-quartz lodes hosted by Paleozoic greywacke and argillite. Other type of deposits present include: volcanogenic massive sulphide lead-zinc; vein and greisen tungsten and tin; and magmatic nickel-copper sulphide, platinum group element, and magnetiteilmenite deposits. Granite stocks and batholiths, intruded during the Cretaceous, have associated porphyry molybdenum deposits.   The Late Paleozoic to Early Cretaceous Eastern Province includes the greywacke rocks forming the axial ranges of the North and South islands, and a belt of schists in Marlborough, the Southern Alps and Otago. The schists host many shear-zone related, gold-quartz lodes and, in the Southern Alps, lenses of serpentinite with talcmagnesite and nephrite jade. Volcanogenic massive sulphide copper deposits and volcanogenic manganesechert deposits, occur in both the schist and greywacke, and a belt of Permian age ultramafic rocks (Dun Mountain Ophiolite) has associated copper, chromite and chrysotile asbestos deposits.   The Late Cretaceous to Cenozoic rocks are found in a number of sedimentary basins onshore and offshore of the North and South Islands. Many of these basins developed during the rifting of New Zealand from Gondwanaland in the Late Cretaceous. They contain New Zealand's economic petroleum, coal and limestone deposits. Uplift and erosion of the mountain ranges shed gold into rich placer deposits in the South Island.   From the Miocene, volcanic rocks feature prominently on the eastern South Island (e.g. Banks Peninsula southeast of Christchurch and the Otago Peninsula northeast of Dunedin) and northern North Island (Northland and Hauraki), and volcanism continues today in the Taupo Volcanic Zone. The North Island volcanic rocks have associated epithermal mineralisation, mainly gold and silver, but also copper, lead, zinc, mercury, and antimony, as well as deposits of sulphur, perlite, pumice and zeolite. Porphyry copper style mineralisation is associated with subvolcanic intrusive rocks. Erosion of the volcanic rocks has shed titanomagnetite onto the west coast of the North Island forming significant coastal placer deposits. Similarly, erosion of the Alpine schists in the South Island has resulted in placer ilmenite deposits on the coast of Westland.

Jan 1, 1997

By F Palkovitz, S Wilson, F Felipe

The management of waste from mining operations is a significant aspect of bringing a mineral commodity to final market. The ore beneficiation process and transport/disposal of waste involves significant consumption of costly resources. A number of options exist to dispose of mill waste on surface and as a backfill material. These range in complexity, risk, capital cost, operating cost and ultimately business performance. This paper discusses the value delivered to a business in using dewatering systems including paste as opposed to conventional slurry tailings disposals. This is illustrated through various case studies and serves to demonstrate how paste can add value and reduce risk to a successful business.

Jan 1, 2009

By Nightingale R, Johnson B, Bensley C, Vince A, Keast-Jones R

In order to counter the massive increase in the level of near gravity material that would follow the reduction in dense-medium cyclone separation density at B.H.P. Slab and Plate Product Division's B and C coal preparation plants, "wing tank" systems to control medium density to within ¦0.005RD units have been installed. However, despite very precise density control, cyclone metallurgical performance has been less than satisfactory. The approaches taken to identify the causes of this poor performance and to justify alterations in operational and maintenance practices are presented.

Jan 1, 1987

LESLIE BRADFORD GOLDEN JUBILEE ORATION "Not only a metallurgist but a scientist of the highest order" Leslie Bradford and the Australian Metallurgical Industry

Jan 1, 1987

A new lead refinery with a. capacity of 230,000 tons per year com-menced operation at*Port'Plsie in October, 1959. This plant' superseded the refinery which had operated from 1933 with the advent of thecontinuous lead refining process. The incorporation of new equipment following local metallurgical developments, together with the overseas demand for lead of extremely low antimony content, created difficulties in operating the original plant. The new refinery project was under-taken to cover this disability and to gain the full advantage of the new processes.Desilverising and softening are carried out in units identical in size to those used previously. Metallic'zinc is now recovered from the entire output of desilverised bullion by vacuum distillation. Final refining is then carried out by batch'treatinent with caustic soda yield-ing lead of purity previously unattainable at Port Pirie.These two processes have replaced continuous dezincing by oxidation, a high temperature process which caused large quantities of lead and antimony to be recirculated. As the final stage is a .batch process the product composition can be.checked before casting. Individual batches can be adjusted to produce special alloys to,consumer's specification.Improved casting equipment has allowed the quantity production of pigs of good physical characteristics either as 56 lb bars or 2000 lb pigs. This, together with the high purity of the lead, has assured the B.H.A.S. position in world markets.Automatic control systems have been extensively employed particularly on the vacuum dezincing unit.The anticipated financial benefits have been achieved mainly by a reduction in the tonnage of recirculated materials, a smaller labour force, and reduced maintenance requirements.

Jan 1, 1963

Five types of mineral resource were known in the sedimentary cover of the oceans and seas floors prior to the 1980's :1) hydrocarbon fields including some very large zones of oil and gas accumulation; 2) "Red Sea" type thermal oozes with increased concentrations of noble metals; 3) ferromanganese nodules; 4) concentrations of metallic sulphides ("Black Smokers"); and 5) cobalt-bearing ferromanganese crusts on the summits and slopes of seamounts. Since then, the so called "White Smokers", containing sulphides of copper and zinc, have been discovered. The ore horizons (manganese, copper, nickel and other metals) of the sedimentary cover of deep-sea basins comprise a sixth type of mineral resource in the oceans. These horizons have not only a theoretical, but also a principal economic significance

Jan 1, 1995

By T Hicks

Designers of mining facilities play a significant role in defining the overall mine greenhouse gas emissions performance. This demands an appreciation of all the greenhouse gas emissions sources, including Scope 3 emissions, which will form an increasing fraction of the emissions as we transition our generation sources to renewable energy. Traditionally overland conveyors are designed to operate as fast as practical, and through this approach, achieve relative minimisation of: conveyor belt tensions; belt width; mechanical equipment masses; structural steel quantities; and concrete quantities. It is well understood that higher belt speeds reduce capital cost and improve project economics. Operating at higher speeds introduces operating costs through system energy losses and increased wear rates. This paper assesses the life cycle greenhouse gas emissions for a typical iron ore overland conveyor to demonstrate how the design criteria and engineering decisions impact greenhouse gas emissions and project economics. An analysis of the decarbonisation potential and project economics using a range of operational parameters has been completed, developing a marginal abatement cost for each system configuration, creating a basis for integration of low emission overland conveyor designs as part of the broader facility decarbonisation strategy.

Sep 1, 2024