Search Documents

The design of mine ventilation systems for the BHP Steel Division Collieries is based on the acquisition of ventilation survey data for the establishment of a realistic computer net- work model. The branches which form the net- work for the computer models are calculated from a range of resistance factors incorporat- ing both a frictional and shock loss component. Since shock losses can account for up to 30 per cent of the total energy losses in mine airways the use of friction factors alone without accounting for shock losses will result in the choosing of an insufficiently performing fan. Published tables of friction factors have in- variably been taken from metalliferous or single entry studies and consequently are not reliable for Australia's mining conditions where multiple entries with regularly spaced cut-throughs are the normal practice. Typical resistance factors for roadways of rectangular cross-section 5.5 m x 2.0 m, with coal sides, have been found to vary from 0.11 Ns2/m8/km where no timber supports are used, to 0.98 Ns2/m8/km where double centre legging together with wooden chocks is used. In addition to the range of resistance factors due to varying support methods, the nature of use for a roadway is very significant because of the condition of repair and upkeep maintained.

Jan 1, 1983

By Wood P. D, Pettifer G. R

In the upper coal surface in the Latrobe Valley, craters known locally as fireholes have developed due to prehistoric coal fires. They can be several hundred metres across and up to fifty metres deep, and are now filled with overburden materials varying from hard baked clays to very soft lacustrine clays. In addition to reducing coal reserves, continuous mining operations are seriously affected by fireholes. Large undulations in the upper coal surface result in a mixture of coal and overburden on the upper mining levels. The very soft lacustrine clays are unstable in the mine batters and the overburden dump, are difficult to handle on the bucket wheel excavator/conveyer system, and have insufficient bearing capacity for the large bucket wheel excavators. Early identification is essen- tial and both drilling and dynamic core penetrometer have been exten- sively used. However, this has not proved adequate in locating and defining the extent of all fireholes, due largely to their irregular shape. To overcome this a range of geophysical techniques has been trialled with very promising results. A trial area has been covered on a twenty metre grid using gravity and Geonics EM34 conductivity measurements and the same area has been covered at a closer spacing with high resolution magnetics. Image processing of contoured magnetic, EM34 conductivity and residual gravity data has resulted in very good correlation with drilling data.

Jan 1, 1989

By S Wan, F Zhang, J You, K Tang, X Tang, C Bessada, A Canizarès, Q Zhang, L Lu

Microstructure of CaO-SiO2-based glassy samples with various Al2O3 contents were examined quantitatively by Raman spectroscopy and 27Al MAS NMR (magic-angle spinning nuclear magnetic resonance). Sequence of multiple cluster models of aluminosilicate system modified with Ca2+ and Na+ cations have been designed, and Raman spectra simulation were carried out after geometric optimisation by quantum chemistry (QC) ab initio calculation. The functional relationship between Raman scattering cross-section (RSCS) and stress index of silicon-oxygen tetrahedron (SIT) for aluminosilicates was established, which was applied to the calibration of experimental Raman spectra. Some five-fold coordinated aluminium (AlV, around 5 per cent) and less than 2 per cent sixfold coordinated aluminium (AlVI) were detected by 27Al MAS NMR, while most of aluminium remained in tetrahedral sites (AlIV). The hyperfine quantitative results of Raman spectroscopy and NMR showed a gradually production of AlIV with addition of Al2O3, along with the significant adjustment of Qi species distribution, in which Q1, Q2 reduced and fully polymerised Q4 increased while Q3 showed a non-monotonic variation and obtained the maximum at Al2O3 = 18 mol per cent. Furthermore, the effects of aluminium to bridging oxygen bond types (T-Ob, T = Si, Al) and the degree of polymerisation were also discussed in detail. The evolution of microstructure and its correlation with the viscosity of CaO-SiO2 based melts, incorporating various Al2O3 additives, have been investigated by employing in situ high temperature Raman spectroscopy at 1823 K and viscosity model. These structural features related to composition are essential theoretic foundation to understand their properties. The average Qi evolution culminates in an overall enhancement of the degree of polymerisation. Viscosity was determined utilising a rigorously selected viscosity model, elucidating a consistent upward trajectory as Al2O3 content is incrementally added. Furthermore, a quantitative analysis of the relationship between viscosity and structure was conducted based on the average number of non-bridging oxygen per network-forming tetrahedron (NBO/T). It provides valuable insights for examining and predicting viscosity behaviour of aluminosilicate systems.

Aug 21, 2024

Continuous improvement in environmental management assists in the achievement of sustainability goals for the mining and processing of minerals. The use of regular internal environmental audits (scored or unscored) which form an integral component of an Environmental Management System (EMS), provide demonstrable evidence of this improvement. The audits described in this paper involve working with site personnel to develop and implement major improvement projects, providing advice on how to improve environmental practices and facilities, and disseminating innovative ideas and practices across the site and to other operations within the same group. Essentially the lead auditor assumes the role of a æskills coachÆ as opposed to a æpolicemanÆ, which is quite often the case for many audits. The audit process has been developed from involvement with a number of major coal mines in the Hunter Valley, where regular internal environmental audits have been undertaken every two to three months, over periods varying from 18 months to five years and more recently, with a metalliferous mine in the Northern Territory. Examples of the benefits of improved environmental performance (driven by the audit process) to sustainable development are provided. The auditing process as described is applicable to metalliferous mines, the processing of mineral ores, coal mines, coal handling and preparation plants, quarries, and oil and gas projects.

Jan 1, 2004

By L Terrusi

The Bungaroo Valley hosts a concealed Tertiary channel iron deposit (CID) along a 17 km stretch of its length. Bungaroo Valley is approximately 0.5 km wide upstream at its easternmost extent, and 3.5 km wide downstream where it joins the Jimmawarrada Creek. The valley follows the axial trace of an anticline that plunges gently to the southeast, and the CID infills the valley. Mineralisation extends to a depth of 230 m below the surface, and almost the entire deposit occurs below the water table. Bungaroo Valley cuts through the Buckland Hills and is bounded to the north and south by steep scarps capped with the resistant Dales Gorge Member of the Brockman Iron Formation. Basement rocks are believed to be mostly Wittenoom Formation shales and dolomites, with Mount McRae Shale and Mount Sylvia Formation also present. Deep, localised depressions appear at the base of the CID sequence towards the north edge of the upstream section of the valley, while downstream the basal CID contact is relatively flat and shallow. In both cases the profile of the CID surface closely mirrors that of the basal contact. The localised depressions seen in the upstream basal CID contact produce significant variations in CID thickness of up to 100 m over short strike distances. This uneven palaeotopography is most likely due to eddying and waterfalls forming within the riverbed prior to CID deposition during a time when the water table was much lower than at present. It may also be associated with possible karsting in an underlying dolomite unit and subsequent syn- or post-depositional collapse of the overlying CID. The irregular basal contact of the Bungaroo CID sequence has implications for mining in terms of pit design and resource accessibility.

Jan 1, 2007

By J McQuie

The concentrator at WMCÆs Leinster Nickel Operation has operated with flash flotation in the grinding circuit since the early 1990s. There has always been a positive correlation between flash flotation Ni recovery and overall Ni recovery û however this relationship could be explained by differences in the ore, rather than by the action of the Flash flotation cell in reducing overgrinding of Ni. In July 2003, refurbishment within the plant made it necessary to operate the concentrator for a period with the flash flotation cells off. The resulting data set provided evidence that flash flotation in the grinding circuit changes the size distribution of Ni to reduce the amount of slow-floating fine (-7 ¦m) Ni produced. Ni recoveries in the finer size fractions were similar with flash flotation on or off û but because less fine Ni is produced when the flash flotation cells are operated, overall Ni recovery improved.

Jan 1, 2005

Computer-based block modelling of orebodies is now used at Renison Tin mine for the estimation of ore reserves. It is considered that this has resulted in improved reserve estimation for complex 'stratafault' orebodies. The results for all orebody types are more easily understood by the mine planning section and provide greater scheduling capability than those from the previous manual isoline reserve estimation method. A structural overview of the deposit can be gained by combining geological block models for the various orebodies. It is anticipated that upon completion of block modelling for all the orebodies the time spent on the annual ore reserve estimate will be significantly reduced.

Jan 1, 1990

In any strip coal mining operation the aosL important single operating unit is the dragline. Because the capital and operating costs of a dragline are high, it is desirable to operate these machines at their maximum efficiency. Thiess Bros. Pty. Limited operate a Bucyrus-Erie 1350 Walking dragline at their Callide coal mine. The operating conditions at the Callide Mine are different from those of other coal mines situated in Central Queens ,nd. The topography is rugged, the coal seam is thick, and the overburden is hard and inter- HH,inded. Several different operating techniques for a large dragline working under these con- ditinns arc discrossmd it tt

Jan 1, 1978

There are a number of examples of how environmental factors have been integrated into the water management aspects of mining projects. The Kingston Lignite project in South Australia, Pine Creek Gold Mine in the Northern Territory, gravel and sand extraction from the Nepean River flood plain near Penrith, and the Olympic Dam Project have all illustrated that consideration of environmental factors can be integrated with project developments, with beneficial outcomes for both the project and the environment.Each of the above cases demonstrated an individually significant environmental issue, directly related to the interaction between the proposed project and its environment. In each case, careful research and an integrated approach to the problem resulted in a solution that gave both maximum protection to the environment and optimum consideration to the economic feasibility and success of the proposed project.The solutions ranged from alternative mining methods and improved waste and water management through to the ultimate objective of converting a mining project into a major water-based recreation source. These examples have set a precedent that will contribute ignificantly to the successful development of future projects.

Jan 1, 1988

In the stability assessment of open pit walls, geotechnical engineers have to deal with uncertainty related to structural geology, rock mechanical parameters, groundwater and so on. This uncertainty will immediately and significantly impact on wall stability assessment and therefore. influence mineral recovery and ultimately the financial return of open pit mining. However, the conventional factor of safety applied to measure the stability of slopes and the relevant analytical computer packages cannot quantitatively consider the variability or uncertainty of the input data. As a supplement, therefore, geotechnical engineers have begun to apply probability to the stability assessment of open pit walls over the last two decades. To-date unfortunately, no powerful computer package is available to geotechnical engineers to conduct the probability analysis of slope stability. This paper presents a computer package of probability analysis for rock and soil slope stability. In this computer package, the strength parameters of rock and/or soil material such as cohesion, friction angle and unit weight of the different rock and/or soil type domain in a complex structural geology environment can be considered as the basic input random variables. Groundwater level can also be taken into account as a random variable in this package. Two `rigorous' limit equilibrium solutions, the Morgenstern/Price method and the Sarma method, can be used to calculate the factor of safety during Monte Carlo Simulation applied in this program. Five types of probability distribution are included in this package for the user to simulate basic input random variables. Two realistic cases from BHP Iron Ore are used to illustrate this package.

Jan 1, 1997

By D P. Obeng, L Reemeyer, R Holmes

The Zinifex Century Mine employs a large number of Detritor mills for fine and ultra-fine grinding to liberate silica and sphalerite at 80 per cent passing 7.5 microns before final zinc flotation. A joint project between CSIRO Minerals and the Zinifex Century Mine was carried out to evaluate the Detritor mill performance. Plant surveys were conducted around the Detritors in conjunction with laboratory tests. The survey data showed that the Detritors in the ultra-fine milling circuit performed well. They reduced a feed F80 sizing of 46 microns to a product P80 sizing of 7.5 microns at a gross energy consumption of 37.2 kWh/t. Scale-up of ultra-fine milling Detritors was studied using a 0.55 kW laboratory batch unit and a 355 kW full-scale Detritor by processing Century zinc concentrate with 1 mm sand media. The results indicated that the 0.55 kW laboratory mill underestimated the energy consumption of the full-scale Detritor by about 20 per cent for a product P80 of seven microns. The performances of a horizontal IsaMill and a vertical Detritor were compared as ultra-fine milling devices for processing Century zinc concentrate. The experimental data demonstrated that, when using the same grinding media, the energy efficiency of the two mills is similar despite the difference in mill designs. The Detritors used for regrind duty at the Century Mine performed poorly when processing feed at 80 per cent passing 88 micron. The energy consumption was high and the product size distribution was broad with particles above 100 microns in the feed unbroken and particles below ten microns overground. A coarser ceramic media of 3 mm was therefore tested in a laboratory Detritor to process the regrind Detritor feed as an alternative to the 1 mm Colorado sand used at the Century Mine. The ceramic media reduced the energy consumption significantly and produced a narrower product size distribution, which is more desirable for the downstream flotation process.

Jan 1, 2007

By R van Wyk

In today’s mining environment the use of heavy mechanical devices and other high-tech electronic devices like two-way radios, cellular phones and even automated mining systems, form a vital part of the daily operations of a mining site. These human-made devices and some of the naturally occurring events, like lightning and gamma radiation, can have negative effects on electronic detonators and the associated control equipment.On larger mining operations the necessity to move the point of safety for blasting further away from the blast area, introduced remote firing via radio frequencies for electronic detonator systems. Other influences on electronic detonators can be abuse or ignorance. To ensure the safety of the end-user, an electronic detonator must be resistant to some common mistakes that users can make. One of main concerns here is resistance to static discharge or incorrect wiring. Despite the daily use of electronic detonator solutions, scepticism and concern still exists amongst those who believe the system raises the risk of a premature initiation of the blast through some form of interference trigger.This paper will help users understand how electronic detonators and the associated control equipment protects itself from external influences. Focus will be on protection schemes to counter static and over-voltage discharge and methods to ensure protection of secure wireless radio links and detonator communications. With well engineered communication systems and solid static and over-voltage protection, an electronic detonator system can be more reliable and safer than other detonator systems. The following main points will be discussed:what makes a detonator an electronic detonator,static electricity and over-voltage protection,the general influence of electromagnetic energy on the detonator,the influence of lightning on detonators,the protection of radio communication’s links as used by remote firing equipment, andthe safety protection features built into remote firing equipment.

Nov 8, 2011

By McLaughlin R. G, Brammer R. A J

King Island Scheelite had been using dealer modified front end loaders for two years when in 1974 it started to increase production. Suppliers were then quoting long deliveries for underground diesel trackless mining equip- ment, and the Company was forced to modify surface machines which had become redundant as production from the open cut phased out. The results were generally successful and encouraged further adaptations. Drill jumbos excepted, the Company now uses only converted surface machines in areas worked by diesel engined equipment and for all support and auxiliary functions.

Jan 1, 1977

The program, WASTRT 70, was set up specifically to handle the design of tunnel liners and underground structures where inter- action between rock and structure significantly affects the design. It may however be used for any mass/R.C. structure capable of being simulated by straight line elements between modes and with loading restricted to nodes. The analysis system adopts typical elastic/stiffness matrix methods. Two main mass/R.C. design segments are utilized (1) Design of section depth based on maximum required stresses and optimum steel/concrete ratios. (2) Design of reinforcement for a given section depth with concrete stresses given for mass and water code structures. Each design segment covers shear, minimum principal stress on ~ , heavy compression as per code (columns), heavy compression one-face steel (tunnel liners), tension and water code requirements for all moment/thrust/section depth ratios on rectangular sections.

Jan 1, 1976

By Giuli M, Barnaba P, Sacerdote R, Tammaro F

Following a theoretical consideration of the effect of flooding, fluidisation and softening on blast furnace blowing limits, results are presented which show the effect of these parameters on operation. Industrial trials on Oscar Sinigaglia No. 4 BF are reported and results compared with those obtained theoretically and in the laboratory. It is shown that in these trials the furnace operated at levels of fluidisation very much (80-90%) below those theoretically calculated whereas in some cases (high proportion of sinter) actual hot metal output was near the calculated flooding limit. However, it was observed that as the sinter percentage decreases also actual productivity becomes lower than the one caused by flooding. This gap, which increases as other ferrous components (essentially acidic) replace the basic sinter was explained by the softening of the burden under bosh conditions. Softening indices measured on the individual materials yield support to this explanation. Coke rates data show that for approximately every one percent increase in the basic sinter in place of blended sized ore, a coke rate decrease of 1.1 kg/thm results. For acidic pellets this value is 0.6 kg/thm. Results of breakdown and reduction characteristics are also given and their indices compared with actual pt oduction. Measures to improve operations are proposed.

Jan 1, 1975

By Aiming Z, Shenyi S, Xialei W

Zhangmatun Iron Mine is situated in the suburbs of Jinan city. Shandong, China. Because of surface environmental constraints, no suitable site can he selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a double- shaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two scopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining.

Jan 1, 1998

By Loo C. E

Thirty two polyacrylamide flocculant samples were selected from the wide range offered to the Australian coal industry. An extensive test program was conducted to consider the properties of the flocculants, the substrates, the process conditions and the water chemistry encountered in coal preparation plants. The study indicated that flocculants with molecular weights of 12 to 14 million and degree of hydrolysis around 40% gave the best "average" performance over a wide range of process conditions. The pick-up and filtration of fine coal was demonstrated on a pilot scale to be a critical function of flocculant properties. This study also showed that the agitation intensity during flocculation was a critical parameter in determining the settling rate of the slurry and the clarity of the resulting supernatant. An electronic meter to measure agitation intensity was designed, constructed and tested to demonstrate how, for the first time, laboratory results can be implemented in operating plants.

Jan 1, 1989

Whereas traditionally, stable isotope research has been directed towards resource exploration and development, it is finding more frequentapplications in helping to assess the impacts of resource utilization upon ecosystems. Among the many pursuits, two themes are evident:(1) tracing the transport and conversions of pollutants in the environment and(2) better understanding of the interplay among environmental receptors, e.g. food web studies. Stable isotope data are used primarily to identify the presence of pollutants in the environment and with a few exceptions, the consequence of their presence must be assessed by other techniques. Increasing attention has been given to the isotopic composition of humans with many potential applications in areas such as paleodiets, medicine, and criminology. In this brief overview examples are used from the Pacific Rim to illustrate the above concepts. Stable isotope data will undoubtedly play an increasing role in multi-disciplinary research in the Pacific Rim. However, consideration should be given to more effective strategies, e.g. networking, for pursuing large scale problems such as long range circulation of pollutants.

Jan 1, 1990

By Chander S

Properties of surface films on chalcopyrite and pyrite differ due to variations in the mechanism of oxidation of the two minerals. In the case of chalcopyrite the first step in the oxidation is the release of iron as ferric ions, which hydrolyse depending upon conditions prevalent in solution. The iron oxide/hydroxide layer formed by hydrolysis of ferric ions is quite porous and easily detachable from the surface of chalcopyrite. When the surface oxide layer is detached a sulphur-rich layer is exposed making chalcopyrite hydrophobic. The thickness and properties of the sulphur-rich layer determine its flotation response, both in the absence and presence of collectors. In the case of pyrite, on the other hand, iron is released as ferrous ions which require much higher pHs to hydrolyse. These ions remain adsorbed on the surface of pyrite making the surface hydrophilic. When the iron species are complexed with chelating agents such as ethylene diamine tetra acetic acid, pyrite was hydrophobic. Siderite forms in the presence of carbonate ions, which might be present in several flotation systems. Siderite nucleated on isolated sites at the surface. The presence of such a precipitate is likely to influence the interaction of pyrite with various reagents thereby altering its flotation behavior. To determine the mechanism of oxidation, kinetics of oxidation of chalcopyrite and pyrite was studied using several electrochemical techniques, namely, cyclic voltammetry, polarisation and impedance spectroscopy. Floatability of the minerals was investigated by measurement of contact angles on mineral electrodes and by Halimond tube flotation. Impedance spectroscopy was especially useful for estimating various properties of surface film for both the minerals. Properties such as charge transfer resistance, porosity, and capacitances of the surface films on the two minerals are compared under several conditions of oxidation. These properties were found to be a strong function of the rate and the extent of oxidation.

Jan 1, 1993

By G Jones

The Singapore Land Transport Authority (LTA) has been procuring the expansion of their underground mass rapid transit rail network at a prodigious rate since the first line opened in 1987. Four lines (149 km) are currently operating and several more lines are at various stages of planning/construction; one of these is the Downtown line stage 2 (DTL 2).DTL 2 contract C917 was awarded in September 2009 for S$320 M. On 18 June 2013 the original contractor became insolvent, leaving the works incomplete. Following a fast-tracked tender process, McConnell Dowell was awarded the S$254 M contract on 29 August 2013 to complete the works. This contract includes two underground stations constructed by cut-and-cover methods and twin bored tunnels between the stations. Each tunnel is 1400 m long, excavated by earth pressure balanced (EPB) tunnel boring machines (TBM) at an average depth of 20 m and segment lined to 5.8 m inner diameter. The tunnel alignment is located under a busy five-lane road lined with prime residential real estate and congested with utilities.To compound the difficulty the tunnels are located within the notorious Bukit Timah Granite formation. This has a very wide range of strength, from below 1 MPa to over 300 MPa. This strength range is a consequence of six weathering grades, from soil to fresh rock, with the fresh granite causing severe abrasion problems. The various grades can occur within a very short distance of each other. Consequently, the problem of supporting a mixed face exists, particularly in the intermediate weathering grades where intact rock is encountered in the invert and corestones within a loose soil matrix in the crown, which can increase the instability by allowing the ground to flow into the TBM.The focus of this paper will be the excavation of the bored tunnels by EPB TBM used by McConnell Dowell to complete these challenging works.CITATION:Jones, G and Shepherd, J, 2014. Earth pressure balanced tunnelling in a dense urban environment, C917A, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 41–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014