Search Documents

Japanese pig iron production in 1973 registered about 90 million tons. As clearly seen from the productivity (2.04 t/m3/D), and fuel ratio (494 kg/t-pig), the Japanese steel industry has maintained quite high levels of efficiency in blast-furnace (BF) operations. Among the many factors which have contributed toward these high levels of efficiency, the use of high quality coke is very important. The Japanese steel industry imports about 85% of its metallurgical coals from various countries of the world, including Australia. The effective use of these metallurgical coals of various origins in accordance with their re- spective properties is most essential for maintaining coke quality. This paper describes coking properties of various metallurgical coals and blending techniques based on these coking properties, in relation to the specifications of coke quality required for efficient BF operations. This paper also describes briefly new technology for expanding the scope of the use of coking coals.

Jan 1, 1975

By L Salvestro

Ventilation on demand (VOD) has been demonstrated to significantly reduce operating costs for ventilation fans, by reducing fan output to meet demand. The most effective method for reducing operating costs is to use variable speed drives to adjust the speed of ventilation fans as required – this achieves significantly larger power savings that damper or vane control alone.However, this mode of control will significantly increase the number of speed cycles the ventilation fans will experience. Fabricated impellers have a limited number of start stop cycles based on the materials and method of construction, and the operating stresses due to centrifugal forces. This means that fans experiencing constant or regular speed changes will experience a reduced fatiguelife compared with fans that are run at constant speed.The fatigue life of fans operated under various speeds using VOD is difficult to predict, as it is dependent on the magnitude of speed changes, and the frequency, which will be varied to meet demand. It is important to be able to estimate remaining fatigue life to assist in maintenance planning and avoid unplanned maintenance activities.This paper will review extensive VOD data on fan operating conditions from two primary mine ventilation fans. This paper will demonstrate how this data can be used to calculate accumulated fatigue and predict the remaining fatigue life, and how this compares with fixed speed or non-VOD controlled fans.The increased maintenance costs for the impellers will also be estimated, and compared to the operating cost savings using VOD, to determine if the savings outweigh the additional maintenance costs.

Oct 12, 2022

By M McGrory, A Rodolfo, J Paredes, L E. Manguba, K A Villaspir, G Webb, R Setiagani, H Cardenas

"OceanaGold’s Didipio operation has been in operation for three years. Integral to the flow sheet design is a flash flotation circuit treating a portion of cyclone underflow, consisting of an Outotec SK-500 flash rougher and an Outotec TC10 flash cleaner and a SB-2500 falcon treating flash rougher concentrate to recover fine free gold.Flash copper recovery has been holding steady at 60 per cent, while flash gold recovery at 50 per cent. Gold recovery from the gravity circuit is 22 per cent, bringing the overall flash plus gravity gold recovery to 72 per cent.Operation of the flash rougher is mainly by pulp level control. Control of copper grade in the flash cleaner is mainly controlled by air inflow and flash cleaner pulp level control drives copper recovery. Gold recovery around the circuit is mainly driven by gold head grade.SB-2500 concentrate is scalped with a 250 micron screen with the coarse fraction reporting to a SB-250 falcon, concentrate of which combines with the screen fine fraction to a Gemini table.Citation:Cardenas, H, McGrory, M, Webb, G, Paredes, J, Setiagani, R, Villaspir, K A, Manguba, L E and Rodolfo, A, 2016. Didipio Flash Flotation and Gravity Recovery Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 123–126 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By I Sherrell, R Jain

Worldwide iron ore feed grades are trending downwards and will continue to do so with the increasing difficulties of upgrading ores. This has led to operations looking for ways to capture current tailings that still contain valuable material. In the past, these were acceptable to dispose of, but this practice is no longer economically feasible. With the increasing trend of re-mining previous tailings deposits that could be decades old, new equipment designs have been introduced to upgrade current or historic beneficiation plants. These designs can effectively upgrade these tailings to saleable products.Outotec conducted test programs for upgrading iron ore tailings from flotation rejects, thickener underflow or tailings dumps on samples provided by customers around the globe. The studies utilised Outotec’s SLon vertically pulsating high-gradient magnetic separator in combination with preprocessing equipment such as low-intensity magnetic separation, screen or scrubber and flotation for downstream processing of the magnetic concentrate. A review of the equipment required to economically process these tailings is provided, along with testing data and industrial implementation examples. The effect of different operational and design parameters on Fe grade and recovery from processing each tailings sample has been highlighted.CITATION:Jain, R and Sherrell, I, 2015. Iron ore tailings reprocessing to maximise ore production, in Proceedings Iron Ore 2015, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By N Ganjian, A Delavar, F Rashidi Nejad

Iran is one of the most seismically active countries in the world, being crossed by several major fault lines that cover at least 90 per cent of the country. As a result, earthquakes in Iran occur often and are destructive. So, it is important to consider the seismic stability and reliability of all structures including tailings dams.In this study, the tailings dam stability of the Sangan Iron Ore Mine in Khorasan Razavi, Iran is considered for the case study. The tailings storage facilities of the mine have three cells with the capacity of 45 million cubic metres. The first cell, which has three stages of dam raising, has been recently brought into operation. This cell has a downstream-raised retaining embankment. As the risk of seismicity in this area is high, seismic response of this dam was evaluated by numerical methods. To do this, appropriate models were developed for materials used in foundation and body of the embankment. Then for seismic stability analysis, Tabas (Iran – 1978) and Chi-Chi (Taiwan – 1999) earthquake acceleration simulations were applied.The results of this study indicated that the upstream portion of Stage 3 of the dam and dam crest did not experience significant horizontal displacements during earthquake period, but the downstream portion of Stage 3 of the dam showed a maximum horizontal displacement of 60 cm at the third stage of dam raising. This is three times more than what was estimated by the designer. Also, the maximum vertical displacement resulting from simulation of the Tabas earthquake was 35 cm. The results of dam response to Tabas and Chi-Chi earthquakes indicate that displacement, shear stress and pore pressure by the Tabas earthquake were higher than the case of Chi-Chi earthquake. The higher energy of Tabas earthquake and the higher frequency near to the natural frequency of Tabas earthquake could be the reasons of this difference. The results of this case study confirm that if the studied tailings dam impacted by an earthquake of a similar magnitude to Tabas, the dam will be seismically stable and the developed strains will not be significant.CITATION:Delavar, A, Rashidi Nejad, F and Ganjian, N, 2015. Seismic stability analysis of Sangan Iron Mine Project tailings dam, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A Lines

This paper addresses a gap in longwall multi-seam interactions and their predictions, providing a case study for future multi-seam operations for both anticipated conditions and a method for understanding the changes in stress regime. Multiple panels were modelled with the results analysed and compared to panel experiences to validate the parameters and properties. The software chosen (LaModel) is a numerical modelling package designed to model stresses and displacements on thin deposits. It utilises a displacement-discontinuity variation of the boundary-element method and has been used extensively throughout both the United States and Australia in multi-seam operations. Analysis of the results demonstrates a clear correlation with the above workings and regions of significant strata instability. This provides the opportunity going forward to analyse new models and incorporate into mine planning and geotechnical designs. Continuous site-based assessment should be undertaken at multi-seam operations to better understand and quantify likely vertical stress levels within the workings. With a detailed analysis of models prior to extraction and a review of models post extraction. Further research is required as LaModel is limited to vertical stress and it is likely that interactions impact both the horizontal and shear stress regime. 3-dimensional modelling could further assist in this understanding, combined with a thorough stress monitoring regime. CITATION:Lines, A, 2018. Modelling multi-seam interactions for longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 185–195 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D Baas, D Bennett

This paper describes how Brisbane-based PanAust Limited develops process control strategies that are implemented at all operations and are used in functional descriptions for plant upgrades and new projects.The process control strategies are determined by operating management philosophies designed to maximise returns from the company’s assets.The approach is endorsed in the project planning and design phases to ensure facilities and equipment that form the major production assets are fit for purpose and capable of enabling the production managers and operators of the projects to maximise shareholder returns.PanAust’s process control approach has been to develop sets of process control standards which focus on two key areas. The first area covers hardware requirements and architecture, software objectives, control models and individual loop tuning methods. The second area defines control room layout, graphic standards and the alarm philosophy. The application of these standards in a new plant or upgrade decreases the time required to achieve design capacity and optimal performance.The PanAust process control strategy changes the operator’s role from one that controls a number of individual loops to one that sets the control objectives of the processing plant. To achieve optimal performance, all the process areas of the plant are analysed to identify opportunities to improve throughput, recovery and stability. Once a key opportunity is identified, a process control strategy is developed which defines the objective of the control, its functionality and how an operator will interact with it. After development of the control model the operators assist engineers to test and debug it. Once the model is robust, it can then be duplicated throughout the group and developed as a group process control standard.CITATION:Baas, D, Bennett, D and Walker, P, 2014. Developing process control standards for optimal plant performance at PanAust Limited, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 325–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By G Burton, S Fityus, J Li, S Vaughan, D Payne

Daunia and Caval Ridge coal mines, owned and operated by BHP, have been co-disposing rejects and dewatered tailings within spoil dumps from the beginning of their operations in 2013 and 2014, with the purpose of minimising environmental impact and geotechnical risk. Following the recent large failures of tailings dams around the world, BHP Coal, through its Coal Tailings Program, plans to transition other coal mines to deliver “dry” tailings and produce mixed plant rejects (MPR) for inpit co-disposal. This will materially reduce future tailings dam risk exposure. Previous laboratory shear strength testing was conducted on rejects with a maximum particles size of 20 mm, and some concerns were raised that this might not represent the mechanical properties of the actual full particle size distribution (PSD) rejects. BHP was also aware that using different technologies to dewater the tailings, such as belt press filters (BPF) and solid bowl centrifuge (SBC), could produce thickened tailings which could significantly modify the physical behaviours of the MPRs, particularly the bonding between particles. Therefore, laboratory testing on both coarse rejects and mixtures of the coarse rejects and dewatered tailings (MPRs), with full PSDs, was carried out. Testing was performed using the large direct shear machine developed by the Australian Coal Association Research Program (ACARP) project C20019 in 2017, as well as a 300 mm diameter triaxial apparatus at the University of Newcastle (UoN). This paper presents details of the laboratory testing program and results for the rejects from the first studied mine of the BHP Coal Tailings Program. It compares the shear strengths measured at full scale with those tested on modified (scalped or crushed) specimens in the past; and discusses the tailings dewatering technique selection from geotechnical aspects based on the testing results, and finally presents some dump and tip head stability analysis results using the testing results.

Jul 1, 2021

By D Connelly

Silver and gold bearing ore from the Troy Resources NL Casposo Gold-Silver Project, located within the San Juan Province of Argentina contains a complex mix of gold, silver, electrum and silver sulphides in the ore. Casposo is a typical low sulphidation epithermal style gold–silver deposit where mineralisation is hosted within rhyolite – andesite flows and breccias. Veins are typically banded quartz–chalcedony colloform - crustiform banded with quartz - carbonate infill. Mineralisation is associated with an assemblage consisting of quartz, chalcedony, adularia, calcite, illite, sericite and trace sulphides. Gold and silver occur as electrum, native silver, sulfosalts and silver sulphides. This paper presents a case study that describes the process selection, development and engineering of a tailored process plant for the recovery of gold and silver from this ore.The original feasibility study, modelling, metallurgical testwork and engineering studies are outlined. The final flowsheet was based on minimising capital cost, operability, recovery and minimising technical risk.The process flowsheet uses the traditional Merrill Crowe route because of the high silver to gold ratio in the feed and achieves maximum gold and silver recovery while providing a common facility for future ore body treatment.

Aug 8, 2011

By Iwu GO, Almond DP, Joasoo _

The gravimetric integral Knudsen effusion method was used to measure cadmium activity values in binary liquid In-Cd alloys in the range 523 to 573 K. The activity measurements together with other studies from the literature indicate that special bonding conditions exist in the melts near a composition corresponding to InCd3. Sound velocities in In-Cd melts were also measured using a precision pulse-echo over- lap method in the range 404 to 953 K. The frac- tional deviation of experimental and ideal isentropic compressibilities at 623K shows a functional dependence on composition with a pronounced maximum near the composition 75 at.%.

Jan 1, 1980

By D J. Brake

The underground metalliferous mining industry continues to change under the influence of many factors including, to name a few, new mining techniques and equipment, new approaches to risk management, more stringent safety and health standards, new employment practices and orebodies become deeper and often lower grade. In addition, the same technological revolution and plummeting cost of technology that has brought the GPS, smart phones and digital cameras to the general population is also working its way through the mining industry impacting on communications, automation and process control as well as introducing major efficiency and productivity dividends. However, not all factors are positive including, in particular, the issues of carbon costs and electrical power. This paper explores some of the trends affecting ventilation in hard rock mines, some of the existing and likely future challenges and some of the potential future solutions to these issues.CITATION:Brake, D J, 2013. Ventilation challenges facing the metalliferous sector, in Proceedings The Australian Mine Ventilation Conference , pp 3-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By R O’Sullivan, D Taylor, J G. McLellan, B Miller

The Mount Isa copper deposit is located adjacent to the city of Mount Isa, Queensland, and lies within a series of Palaeoproterozoic to Mesoproterozoic Superbasins. The deposit is hosted almost entirely within the Urquhart Shale (US), a unit of the Mount Isa Group sediments and part of the Isa Superbasin. The copper mineralisation is separated into two distinct orebodies: the X41 mine (1100 and 1900 orebodies) and the Enterprise mine (3000 and 3500 orebodies). The orebodies are situated in the hanging wall of the major controlling structures, the Paroo Fault, which has juxtaposed older basement Eastern Creek Volcanics against the younger Mount Isa Group sediments cf 1655 ± 4 Ma. Conjecture remains over the exact timing of this thrust event. However, it is clear that inflections on the Paroo Fault have a close association with the orebodies and are an important structural feature in the mineralisation of the Mount Isa copper deposit.The life-of-mine is reducing steadily and new geomechanical modelling techniques were employed to target structurally controlled mineralised zones in three dimensions. Following a structural review of the mine using underground mapping, structural data and core shed observations, a conceptual 3D mine model was constructed utilising existing data modelled in MineSight®. This conceptual model included all the main lithological units and structures. The conceptual model aimed to test the effects of deformation on the main lithological and structural components of the system and attempted to highlight areas of anomalous stress and strain that may indicate a higher likelihood of fluid focusing and mineralisation potential. This project was focused on testing the latter stages of a D3 event (NE–SW compression) and D4 event (SE–NW compression), which are considered to be responsible for the current location of the mineralisation.The fully coupled 3D finite element analysis models resulted in highlighting anomalous patterns of stress and strain and subsequent fluid flow as a result of the two deformation events. The NE–SW D3 simulation provided the best correlation with the known distribution of mineralisation. This event also indicated several areas on the Paroo Fault and within the US that have potential to host further areas of mineralisation. The SE–NW D4 simulation provided less of a correlation with known mineralised zones. However, this event may have been responsible for post mineralisation re-mobilisation of copper on a relatively small scale. Areas of maximum shear strain, shear stress, volumetric strain and fluid flow correlated well with areas of minimum principal stress and provided the best overall match with known mineralised zones. Furthermore, several additional highlighted areas provide a high potential for further discovery of copper mineralisation. Recent exploration drilling north of the Enterprise mine 3000 orebody, utilising geomechanical modelling as part of the targeting criteria, intersected copper mineralisation, providing further validation of the modelling results.CITATION:McLellan, J G, O’Sullivan, R, Miller, B and Taylor, D, 2014. Geomechanical modelling of the Mount Isa copper deposit – predicting mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By OÆShea P. J, Dickson T. W

In April 1994 the Victorian Premier announced new State initiatives, collectively termed the Victorian Initiative for Minerals and Petroleum (VIMP), for exploration totalling $16.5 m over three years. The program, initially centred on the northwest of Victoria, the Eastern Highlands and the Otway Basin, is due for completion in June 1997 and has been designed to attract explorers to highly prospective but currently under-explored parts of the State. Major components of the program include acquisition of geophysical data (including airborne magnetics and radiometrics, gravity and seismic data), stratigraphic drilling, geological mapping and mineral resource data compilation. At the completion of the current program, 70 per cent of the State will have been covered by airborne magnetic and radiometric coverage at 400 m line spacing or better (Figure I) while 20 per cent of the State will have been covered by new geological mapping. The completion of database compilations for geochemistry, mine data and exploration licence summaries during the VIMP program is shown in Figure 2. The new airborne geophysical surveys have been flown partly under the VIMP program and partly by AGSO under the National Geoscience Mapping Accord (NGMA). Data from these surveys have been interpreted and incorporated into the geological mapping in order to enhance the quality of map products, especially in areas of Cainozoic cover. The first series 1:250 000 scale geological map coverage of Victoria was completed by the Geological Survey of Victoria (GSV) in 1977, and was based on compilation of historical geological mapping with minor field checking in most cases. The first metric 1:50 000 scale geology maps were also commenced in the 1970s, but were discontinued in the 1980s in favour of 1:100 000 scale map production. Driven by customer survey findings and with the benefit of detailed airborne geophysical data in the 1990s, the GSV reverted to 1:50 000 scale map production in 1995, with 1:10 000 scale maps made in areas of significant gold production. Geological reports still cover standard 1:100 000 scale map areas, but are now accompanied by four 1:50 000 scale maps. These new series 1:50 000 scale geological maps have been supported by comprehensive mine data and exploration licence summary databases in addition to the new geophysics, and benefit from the advances made in structural geological interpretation over the last decade. The new phase of geological mapping in Victoria, commenced under the NGMA in 1990 and accelerated under VIMP in 1994, has been focused in the central Victorian goldfields and eastern Highlands areas of the State (Figure 1). Results to-date have led to a number of major advances in the understanding of the eeoloeical evolution of Victoria.

Jan 1, 1997

By Q Gong, J Li, J Zhao, Y Zheng

Excavation by tunnel boring machines (TBMs) offers many advantages over conventional excavation methods, in terms of safety level, working environment, advance rate and overall cost. While TBMs have been extensively used in civil tunnel construction, they are also viewed as a competitive alternative to the drill-and-blast method for underground mining, attracting increasing attention from the mining industry. This paper presents an overview and general assessment on applications of TBMs in mines, by reviewing more than 60 TBM applications in underground/open pit coal and hard rock mines around the world. The projects range from the early exploratory trials of TBMs in mines in Germany, England, South Africa and America in the 1960s and 1970s, to the ongoing projects in Australia, China and Chile. The paper focuses on the geological compatibilities, the problems encountered, the solutions undertaken and the lessons learned from those projects. The paper summarises the progress made in the past and highlights the challenges faced by TBMs in mining due to complex ground conditions and geometrical requirements. With the technological advances of TBM and experiences gained in the past, more applications of TBMs are expected in underground coal and hard rock mines.CITATION:Zheng, Y, Gong, Q, Li, J and Zhao, J, 2014. A review of the applications of tunnel boring machines in mines, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 691–704 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M P. Sandy, R M. Stephenson

Portals to access underground mines are important infrastructure and their design requires careful consideration. Portals are generally expected to last for the life of the mine. Typically, the exposure of personnel and equipment is high, with many hundreds of movements through the portal per day. Consequently, the risk associated with geotechnical instability must be extremely low. Portals are often established from a boxcut. In areas where the weathering profile is well developed, the design and execution of the boxcut can involve significant effort, with the objective of minimizing the volume of the boxcut, whilst ensuring that conditions at the design depth are suitable for establishing a stable portal. Properly designed site investigations are a critical part of this process. Currently available portal design guidelines have not been updated for decades, however the equipment and ground support systems have changed significantly in recent years. Many mine portals have since been constructed in a relatively short time frame with success, often in challenging ground conditions using some of the more modern approaches to ground support. This is beneficial because delays in establishing a portal will generally delay other critical path activities, and lead to cost overruns.

Mar 15, 2021

By P Collier

From 1972 until 1989 when operations were suspended Bougainville Copper Limited (BCL, owned 53.58 per cent by Rio Tinto Limited) operated a large open pit mine and processing facility at Panguna on Bougainville Island, Papua New Guinea producing copper concentrate containing significant quantities of gold and silver.BCL has a stated vision of recommencing operations at Panguna. In 2008, Rio Tinto, on behalf of BCL, conducted a multi-disciplinary study to assess the technical and financial viability of redeveloping the Panguna operation. One of the key outputs of the study was a Joint Ore Reserves Committee (JORC) Code compliant mineral resource statement based on the existing block model and fundamental data, archived since mine closure. Historical data (including the resource block model and drill hole data) was recovered from computer archives by a former Panguna mine employee familiar with the various obsolete data formats, thus maintaining an unbroken chain of custody of the data by Rio Tinto since operations were suspended. No additional data were collected as part of this study.The extensive data and documentation archive facilitated a sufficiently detailed evaluation of the fundamental data and model to support an updated resource statement. Table 1 of the JORC Code was used to guide the model validation process.Reconciliation of blasthole and metallurgical plant data with the reserve model, indicated that the copper and gold drill hole composite database was significantly biased towards underestimation in several key domains due to a combination of the following: mineralisation loss during core loss, core loss (minor), vertical drill holes failing to intersect sufficient subvertical mineralised fractures and veins, drill hole spacing too wide, and variable diamond drill hole core size. The resource model evaluation was based on three material types (all previously mined at Panguna), that were defined based on cut-off grade and rock type parameters: direct feed ore – material for delivery directly to the plant, preconcentration and screening ore – subeconomic material beneficiated to produce fines of economic grade, and waste. Three pit shells and designs were generated based on three separate sets of economic parameters. These economic parameters were also used to assign material types to the block model. The three resulting models were then evaluated against the corresponding pit shells.Classification of the resource was approached conservatively due to the inherent bias in the drill hole data. Consequently only Indicated and Inferred resources were tabulated.The study highlighted the importance of maintaining detailed documentation pertaining to resource estimates and operational history, particularly reconciliation, and the value that can be added by a simple, low-cost data compilation exercise.

Aug 22, 2011

By A M. Nyembwe, A M. Garbers-Craig, R Cromarty

With the depletion of high-grade lump iron ore, concentrates have been identified as an alternative material for sinter making. Adding concentrates to the sinter mixture reduces sinter bed porosity and gas flow through the sinter bed. This will result in lower sinter strand productivity. A potential solution to this problem is to add concentrate in the form of micropellets. This study investigates the effect of concentrate and micropellet additions on the permeability of the sinter mixture. Permeability was measured on sinter mixtures containing ten to 40 per cent concentrates and micropellets at various moisture contents. The effect of concentrate and micropellet addition on the permeability–moisture relationship was examined. The results confirmed that the addition of concentrates into the sinter mix decreases the maximum permeability of the sinter bed. The incorporation of micropellets into the sinter mix reduced the permeability less than concentrate addition. The study also showed that the maximum permeability of sinter mixes containing concentrate is reached at the same moisture content as the sinter mixture without concentrate addition. For sinter mixes containing micropellets, additional water must be added to obtain maximum permeability. Parameters including the granule size, void fraction and angle of repose were also investigated to evaluate their effects on the sinter bed permeability.CITATION:Nyembwe, A M, Cromarty, R and Garbers-Craig, A M, 2015. Effect of concentrate and micropellet addition on iron ore sinter bed permeability, in Proceedings Iron Ore 2015, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By E Kunz

Decreasing the gas content in the worked seam by degassing before the start of winning has proven its worth in some areas of German hard coal mines. On the one hand, it removes the risk of gas/coal outbursts and on the other hand it reduces the gas inflow into the longwall. The underground experiences of the last 30 years have led to a æhit listÆ of coal seams with respect to their suitability to predegassing. Trials in the DMT laboratory and also results gained in the deposit show that the suitability of a seam for predegassing depends on its rank. In seams with volatile matter of 20 - 30 per cent, high efficiency ratings are achieved as a rule, with lower ratings both in seams with lower and with higher content of volatile matter.If the rock pressure is unusually high, the efficiency rating of the predegassing is lower, even in seams which would normally be suitable for this process. Under unfavourable conditions, for example below or above residual pillars, in-seam boreholes cannot be drilled successfully and the method is not practical. But if the worked seam was already stress relieved, the predegassing has an optimal efficiency. Latest investigations show that the distance between the in-seam boreholes can be extended. But in that case, the time necessary to reach the same reduction of the gas content increases considerably.

Jan 1, 2005

By D T. Ribeiro, J F. C L Costa, J C. Koppe

Drilling and sampling are responsible for most of the costs during mineral exploration, especially in multi-elements and polymetallic deposits, such as iron, manganese and bauxite deposits. On these deposits, often it is necessary to estimate multiple attributes at several granulometric fractions, ie distinct particle sizes. This paper investigates the effect of sampling at a close spacing grid only the head grades for the multiple chemical species in iron ore deposits. The remaining required data at the various grain sizes are sampled at a sparse grid. The derived geological model is checked for precision and accuracy comparing the output obtained against a model obtained using a complete isotopic data set including head grades and chemical analysis at each granulometric fraction analysed at all sampled positions. Among the several tested alternatives, the best procedure for dealing with the posed problem involved utilising the correlation coefficients between the grades at distinct fractions to obtain an isotopic database prior to interpolation. Cokriging was the method used, based on the intrinsic coregionalisation model. Estimates were obtained with the quality needed for the proposal of the study. Results showed that at least 50 per cent of the blocks were estimated with errors less than ten per cent relative to the grades obtained at the reference model, using only 15 per cent of the granulochemical data employed to obtain the reference model. The methodology also preserved the correlations between the attributes in their several granulometric fractions on the estimated model.

Sep 26, 2011

By S C. Dominy, R C. A Minnitt

Determination of the sampling constant and liberation diameter are of importance when applying the Fundamental Sampling Error (FSE) equation to optimise sampling protocols. The method for the direct determination of the sampling constant is based on the æGy 50-pieceÆ experiment and variants thereof, which is generally known as the heterogeneity test. In the coarse gold environment, the heterogeneity test is prone to poor repeatability and bias due to the very heterogeneity that it aims to quantify. A key issue is the large sample mass that can be required in the coarse gold environment, which may reach 1 t or more. The heterogeneity test often provides an evaluation of the background gold grade heterogeneity, but understates that of the high-grade coarse-gold component. This is because the total mass of fragments is usually too small to represent the mineralisation. Despite this relatively well-known problem, heterogeneity tests are often undertaken on deposits where the presence of coarse gold is ignored, not fully realised or vastly understated. Sampling types and protocol designs are frequently based on poor quality data that do not match the characteristics of the orebody. For this style of mineralisation, an empirical approach to define ore characteristics is recommended.CITATION:Dominy, S C and Minnitt, R C A, 2012. Application of heterogeneity testing to coarse gold ores, in Proceedings Sampling 2012 , pp 143-160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012