Search Documents

The green field discovery of a two million ounce high-grade refractory gold ore deposit in the Indonesian Province of Sulawesi Utara, led Newmont to utilise its proven technical expertise in dry grinding and whole ore roasting to develop a 2000 tonne per day, 160 000 ounce per year operation in this remote and picturesque location.Located at an elevation of 250 in above sea level and ten kilometres to a deep water natural harbour, the hard rock open pit mine, process plant and infrastructure facilities were built to budget at a capital cost of US$132 million. The plant was commissioned with oxide ore, with the first gold poured in March 1996 and with refractory ore in January 1997. The operation rapidly met its production targets because of extensive forward planning and training programs developed for the local workforce. The presence of steep topography, fertile coastal plains, high rainfall, high seismicity of this location led to the decision to dispose of neutralised tailings in deep water off the coast instead of impounding tailings in a dam. This paper describes the development of the project and the challenges in developing a gold operation in a remote location which lacked infrastructure, the steps taken to ensure a smooth commissioning, and the selection of the workforce to operate a technically sophisticated facility.

Jan 1, 1997

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

The Yabulu refinery of Queensland Nickel Pty Lld near Townsville now imports more than three million wet tonnes per year of nickel laterite ore from New Caledonia and Indonesia, making it the largest importer of any commodity in Australia. The project has illustrated that importing untreated bulk ore and re-exporting high value products makes good economic sense for the company and the nation.The economics of this exercise were considerably enhanced in 1994 by changing the project's principal product from nickel-oxide sinter to refined high-purity nickel metal. It is one of the few operations in the world where nickel ore is transformed to nickel metal at a single site.Several novel technological processes were developed at Yabulu and incorporated into the refinery to allow this product transition to occur. By utilising internally developed technology the new processes were installed at a capital cost of less than $10 million. It is unique for a large nickel producer to change completely the quality of its entire product range many years after the plant was constructed and considerable attention to marketing the new products has been required.The changes have meant that the project is no longer limited to selling lower-value oxide sinter to a relatively small number of large stainless steel mills. In the past year sales of the new high purity nickel metal products have expanded to include a broad range of international customers in the special alloy, foundry and chemical industries.

Jan 1, 1995

By D Bertoldi, C Haines

"The Waihi Gold Mine (WGM) operated by OceanaGold New Zealand Limited is a wholly owned subsidiary of the OceanaGold Corporation of Australia. Traditionally WGM has stockpiled and processed separate campaigns of open pit and underground ore. The ore is processed via a conventional semi-autonomous grinding (SAG) / ball circuit (SABC). The low aspect SAG mill operates in a closed circuit with two 20" cyclones, whilst the ball mill is also a closed circuit with a 10" cyclone cluster. A major wall movement in April 2015 ceased open pit operations indefinitely, 18 months ahead of the mining plan. This immediately reduced the forecast mill tonnage leaving two options: begin campaign milling or change the operating strategy and target lower throughput. Additional cost pressures necessitated improved milling cost efficiency. The immediate ore restriction limited processing alternatives to within the existing major infrastructure. Available comminution circuit survey data laid the foundation for developing a comminution model using the JKSimMet™ software package (version 6, created by KJTech). A number of flow sheet variants were then evaluated based on predicted throughput and efficiency. The comminution models suggested opportunities for improved efficiency lay in reducing throughput and increasing utilisation rather than on/off campaign milling under the existing operating philosophy. A series of process alterations followed, delivering new cost efficiencies that maintained the current $/t processing cost. This paper aims to review the change in circuit performance and examine the decisions and challenges faced following the transition from a high tonnage SABC circuit to lower tonnage SABC circuit.Citation:Haines, C and Bertoldi, D, 2016. The Transition from Semi-autogenous to Autogenous Milling at Waihi Gold, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 303–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By E N. Sparg, O D. A Deuchar, F Needham

Decline shafts are an attractive option to both new and existing mining operations where there is a need to access an inclined orebody deposit via on-reef development so as to generate a return in the shortest possible time. There are many different technologies that are available to transport men, material and rock in incline shafts. This paper focuses on the applicability of two hoisting technologies for decline shafts, namely endless and direct rope systems. The pros and cons of each system are reviewed. A common concern with direct rope haulage systems is the possibility of generating slack rope during deceleration. This paper illustrates the issues involved in designing a system so as to avoid the possibility of slack rope. In conclusion, the key factors relevant to the selection of endless or direct rope haulages for a particular decline application are reviewed. The paper is a joint submission by FFE Minerals-Vecor and Qualter Hall UK.

Jan 1, 2005

By W Patton, I Minniakhmetov, H Talebi, U Mueller

The sustainability of mining projects is linked to informed investment decisions based on public reporting of exploration and mineral resource estimation results. In Australia, public reporting guidelines are established by the Joint Ore Reserves Committee reporting code through the JORC Code (2012). Although the assessment of uncertainty in the results reported is a requirement, this is often communicated qualitatively and evaluated subjectively. This can become a liability particularly in the early stages of mining projects when spatial domains of geological interpretation and mineralisation envelopes inform resource estimations’ reliability. A recent review of JORC reports found no reports used quantitative assessments of the geological interpretation or mineral resource estimation envelopes, and 27 per cent of reports did not address the question of quality of geological interpretation. Reports that did address the quality used 19 different terms to communicate quality. This work presents methodologies for quantitative uncertainty assessment and communication and explores how they could be applied in public reporting practice. Quantitative uncertainty reporting would benefit mine planning and financial modelling as they normally assume the geology is 100 per cent right (since no error is reported or only a single deterministic model is provided). The complexity, cost, and additional work of doing a quantitative assessment could hinder a straightforward implementation. This could be overcome if mining companies budget for quantitative uncertainty assessment and associated professional development. A compulsory requirement for the inclusion of uncertainty assessments in public reporting or adopting standardised subjective language would improve industry practice.

Mar 22, 2022

By R N. Lamb, A N. Buckley

Experiments have been carried out to establish whether time-of-flight secondary ion mass spectrometry (ToF-SIMS) is able to differentiate monolayer and multilayer coverage of thiol collectors on sulfide minerals. The systems investigated were those for which x-ray photoelectron spectroscopy is able to provide an independent determination of the extent of coverage, and included diethyldithiophosphate (DTP) and 2-mercaptobenzothiazole (MBT) on chalcocite, DTP on Ag2+MS prepared by sulfidising metallic silver, and isobutyl xanthate (BX) and MBT on galena. For monolayer adsorption of MBT on chalcocite, peaks from MBTû but not Cu(MBT)û ions were evident. For multilayer coverage, Cu(MBT)2û ions were clearly present, notwithstanding the fact that other data had identified the principal multilayer species as Cu(MBT). For adsorbed DTP on copper and silver sulfides, DTPû and metal(DTP)Hû peaks were observed for monolayer and multilayer coverage. Although the multilayer species was expected to be predominantly metal(DTP), metal(DTP)2û ions were evident for multilayer (but not monolayer) coverage. For the PbS/BX system, intact Pb(BX)2 or Pb(OH)BX ions were not detected for multilayer coverage, although Pb-containing ions heavier than PbBX were. Indeed, for all the systems studied, ToF-SIMS was able to differentiate monolayer from multilayer coverage. In general, however, the SIMS evidence alone might not be sufficiently definitive to effect the differentiation. In the case of collector adsorption on copper and silver sulfides, if the multilayer species detected had been the metal monothiolate only, and had not involved the formation of some metal dithiolate, then ToF-SIMS might not have been able to provide an unequivocal differentiation of the two coverage conditions.

Jan 1, 2005

By A Esfahanipour, M Osanloo

Determination of cut-off grade?strategy is one of the most important stages of open pit mine planning and design. It is the parameter directly influencing the financial, technical, economic, legal, environmental, social and political issues in relation to mining operation. Choosing the optimum cut-off grade strategy that maximises the economic outcome has been a major topic of research workers for nearly one century. Many researchers have contributed in devising methods and algorithms, such as dynamic programming, linear programming, optimal control and so on for various aspects of its determination. In this paper, a non-linear mathematical programming for cut-off grade strategy optimisation is presented, considering the three main stages of mining operation introduced by K F Lane. In this model maximisation of net present value of mining operation, under the three constraints of mining stagesÆ capacities, considered as the optimisation criteria. Due to the discrete representation of the mining resource, the proposed non-linear formulation is approximated by a non-linear signomial geometric programming. According to non-convexity and the complexity of the proposed model, an augmented Lagrangian genetic algorithm was used to find the optimum cut-off grade strategy under varying and fixed price circumstances. To validate the proposed non-linear model efficiency, the results were compared with the results obtained by the K F Lane methodology. It was found that the proposed non-linear model works efficiently in the determination of cut-off grade strategy. According to the simplicity of the structure of non-linear programming modelling in comparison with dynamic programming it is hoped that, further development of this model would certainly provide the ability of considering managerial and technical flexibilities as well as incorporating more real mining conditions in the determination of cut-off grade strategy optimisation.

Sep 26, 2011

By G M. Mudd

The growing popularity of platinum and platinum group metals (or PGMs, including palladium, rhodium and others) for a wide range of applications leads to some interesting issues for mining and sustainability. The uses for PGMs includes catalytic converters for air pollution control in vehicles, growing jewellery use, catalysts for various purposes (especially petroleum and chemicals processing), hydrogen fuel cells and many others. Given the growing importance of most of these PGM uses in more sustainable technologies or in making industrial processes more efficient, it is critical to understand the complex sustainability issues which surround platinum and PGMs. At present, South Africa is the dominant PGMs producer and holds about 88 per cent of estimated global resources, with important but relatively minor production and resources in Zimbabwe, Russia, Canada and the United States. Given the concentrated location of PGM resources, what are the likely trends in PGM mining with respect to environmental sustainability? That is, what are the costs in terms of energy, pollution, greenhouse gas emissions, water, land use impacts, social impacts, economic aspects associated with this globally important industry? This paper compiles and analyses a range of data on platinum-PGM mining, focusing primarily on South Africa. It synthesises a unique combination of data which relates typical production aspects such as ore grade and scale with sustainability aspects such as greenhouse, energy and water costs. The findings are critical in understanding the debate about the increasing environmental and social costs of some materials and technologies which are considered crucial for sustainable industries based on PGMs. Overall, the paper represents a valuable insight into the platinum-PGM sector, providing a range of useful data for understanding the environmental sustainability of this particular group of precious metals.

Jan 1, 2009

By P Mikula, R Geranmayeh, R Carlton, M Ferguson, R Whiting

The concept of using specially designed slot blasts to mine through stress abutments that intersect faults, while controlling fault-slip seismicity, has come of age at Mt Charlotte Mine. Due to the high and adverse stress field and the presence of major faults, the mine is vulnerable to significant fault-slip seismicity. As mining proceeded, advancing stress abutments around various mined areas encroached on several major subvertical faults. If the sequence formed a diminishing pillar between stope and fault, the removal or failure of that pillar daylighted the fault, and often resulted in significant fault-slip seismicity. A new strategy called ‘Tight Slot Blasting’ (TSB) was developed to restrain or dampen this style of fault-slip movement. The TSB has geometric similarities to a conventional cut-off slot used to create stress shadows, but its function is different. Its objective is to trigger and control a sudden shift of the stress state on a fault from an initial stable state, through an unstable transition, to a second stable state. A TSB firing advances a long tall narrow slot through a stressed abutment between a stope void and a nearby fault, using a rapid blast with a low swell ratio, so that the slot substantially and rapidly fills with blasted rock fragments. During the blast process, the stressed rock is rapidly removed and transformed into the fragmented rock fill in the slot. The strategy deliberately allows a fault-slip episode to manifest at a chosen time and place. The tight-packed broken rock in the slot performs an essential shock-absorbing function by controlling the slip amount and rate on the fault, while at the same time the fill becomes compacted by the movement. This controls the dissipation of fault-slip energy, and greatly reduces the seismic response in time and space. A small closure across the slot occurs, with consequent relaxation and destressing of the adjacent rock mass. Stress monitoring data shows that slot creation lowers the abutment stress in the nearby rock mass, while the newly placed fragmented rock fill acts as a shock absorber, providing considerable resistance to substantial fault-slip movement that otherwise could deliver a significant seismic event. First used in 2007, the strategy has been refined to become a routine specialised practice for management of seismically hazardous situations at Mt Charlotte, with 12 successful TSBs conducted to date. Despite mining through multiple high stress abutments, seismic reactions have not exceeded ML 2.1 with any TSB firing, all remaining below the site tolerable maximum of ML 2.3. This paper presents an overview of the strategy, and five case examples of the strategy in critical stressed areas in July 2016, Sept 2017, Dec 2017 and two in Oct 2020. The strategy has successfully managed the seismicity and is expected to remain an essential part of the seismic management plan at Mt Charlotte Mine.

Nov 29, 2022

By T M. Brettell, D Sidea

The CSA Mine is located in Cobar, New South Wales and is operated by Glencore. Large scale underground production started from 1965, with zinc, lead, silver and copper extracted in the past. The current operations focus on copper, with a silver co-product.From 2014 to 2016, Cobar Management Pty Ltd (CMPL) undertook a major capital project to upgrade the primary ventilation system at the CSA Mine. This involved the development of ten raises using full-face raise boring from surface to a depth of 1450 m. The total length of the raises was approximately 2500 m. Geotechnical conditions were identified as a key project risk during the early planning stages of the project. Timely quantification of the geotechnical risks was required to minimise project delays and cost overruns. Geotechnical investigations were planned and conducted for each raise prior to pilot drilling and full-face back reaming.Nine of the ten raises had final wall camera and laser baseline surveys completed following full-face reaming. The surveys were conducted progressively, allowing ongoing back analysis and calibration of geotechnical evaluations as the project advanced.This paper presents the design and planning process of the raise bored excavations. It details the geotechnical investigation work undertaken to mitigate the geotechnical risks and the challenges and learnings from the project including the benefits of close collaboration between the parties involved.CITATION:Sidea, D and Brettell, T M, 2017. The CSA ventilation upgrade – geotechnical challenges and learnings, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 341–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By M Schaffer, T Kewe, N Moffatt

Porgera mine is 95 per cent owned by Barrick Gold Corporation. It is located at an altitude of 2200–2700 m above sea level in the Enga province of Papua New Guinea and produces approximately 460 000 oz per annum with a proven and probable reserve of 6.2 Moz. The refractory ore is ground in a conventional semi-autogenous grinding and ball mill circuit. After the gravity gold is recovered, the slurry is floated, oxidised in the autoclaves and then leached. This paper will focus on the flotation circuit and the recent upgrade of the control system. The five interdependent flotation circuits were challenging for operations to control as they dealt with variable grade, throughput and circulating loads, as well as the physical limitations of the equipment. With the installation of 18 Portage Froth Characterization® (PFC) cameras, the plant’s operation has been converted from a level-control based strategy that was focused on individual cells to one that targets grade and recovery control across the entire circuit. Variability in feed and the corresponding launder issues were addressed with a unique site initiative of deflector plates to indicate filling level. Non-linear closed loop control was implemented directly in the DeltaV Distributed Control System (DCS) using Portage Advantage Regulatory Control (PARC) algorithms and optimised with AwaRE advanced controllers. The most noticeable benefits achieved with the upgrade include improved flotation gold recovery, consistent flotation sulfur grade and autoclave performance. Correspondingly, there was a significant drop in boiler diesel fuel usage and launder overflow conditions.CITATION:Kewe, T, Moffatt, N and Schaffer, M, 2014. Porgera flotation circuit upgrade and expert system installation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 345–356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By S Gray

Based on the 2021 Volume 5 State of PlayTM mining survey of key executives and board members in the mining sector, the key responses to ‘Which of the following technologies will have the biggest impact on mining in the next 15 years?’, were ‘Sensing and Data’ followed by ‘AI and Analytics’. From the early 1970s it would have been unlikely to predict the level of sensing and automation introduced to the broad industrial sector. No better example is the automobile industry where the combination of technological advances and external drivers (such as emissions control) have driven an incredible rate of change. The introduction of sensing, data, AI, and automation in the mining industry is just ramping up. Until now our energy efficiency, environmental footprint, labour shortage, skills, and safety have not been challenged by stakeholders in the way we are seeing market forces develop today. In order to address these challenges, we need to look back to the automobile industry and learn their lessons to accelerate our application of digital capability, analysis, AI and automation This is critical, particularly as access to skilled human resources becomes more difficult. An example of how this can be achieved in a gold processing plant utilising the latest real-time sensing technologies is the ‘Carbon Scout’ developed by Curtin University, and OLGA developed by CSIRO, which are both online technologies, coupled together with Gekko’s ‘Neon’ digital platform to achieve a fully automated real-time gold processing system.

Aug 24, 2022

By E Coffison, M Gibbs, C Bennett

The sustainable management of surface water associated with coal mining and coal seam gas projects is a considerable factor affecting the global competitiveness of these resource companies operating in Australia. Management of surface water can be costly, but effective water management and hence environmental stewardship enhances corporate social responsibility and the social license to operate. The surface water issues for the two industries are comparable, yet there is currently a lack of alignment between how Queensland, where the majority of AustraliaÆs coal seam gas projects are located, manages and regulates water on coal mine projects and coal seam gas projects.This paper provides a high level comparison of Queensland legislation and highlights the lack of alignment of this legislation regarding surface water management in these two industries. Through a case study, it looks at the surface water management process at a coal mine site based on the current legislation and principals of surface water management. QueenslandÆs lack of alignment in legislation regarding surface water management in these industries is understandable given the different development paths and time scales of the two industries. The coal mining industry has developed over a long period of time and the legislation has progressed in parallel, whereas, the coal seam gas industry is relatively new in Australia and the legislation has had to advance quickly. The lack of alignment between management of surface water for the two industries creates confusion among stakeholders and this adds complexity and additional transaction costs during the exploration, permitting and operational phases of projects, including landowners who may be affected.CITATION:Bennett, C, Coffison, E and Gibbs, M, 2013. Lack of alignment between regulation of surface water management in coal mining and coal seam gas, in Proceedings Water in Mining 2013 , pp 157-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By A Giblett, S Hart

"In 2015 operations under the ownership and/or management of all Newmont Mining Corporation subsidiaries (Newmont) produced 5.7 Moz of gold and 619 Mlb of copper from mining operations in five countries, with well over 100 Mt of ore processed by various grinding technologies. Processing methods used in the extraction of metals include flotation, oxidation, conventional cyanidation and heap leaching. The grinding technologies applied in milling operations feeding metal recovery processes include conventional wet grinding semi-autogenous grinding (SAG), rod and ball, dry grinding, concentrate regrinding and ultra-fine grinding, and ball milling of high pressure grinding roll product. SAG/ball (SAB) configurations represent the dominant comminution flow sheet within the company and the circuit configurations employed include SAB, SABC-A, SABC-B and single-stage (SS) SAG milling, with SAG mill feed ranging from run-of-mine (ROM) ore through to secondary crusher product. The collective experiences earned from designing, operating and debottlenecking these various comminution circuits provide many lessons that can be applied to the design and optimisation of future operations. This paper provides an overview of Newmont’s diverse comminution circuits, discusses recent performance and offers some insight into optimisation and design considerations based on recent experience in both endeavours.Citation:Giblett, A and Hart, S, 2016. Grinding Circuit Practices at Newmont, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 293–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Voss Smith F, Matters C. W, Slee R. T, Coldham JC, Davies HW, Wallman H. H

The Committee desires to thank the managers of the various mines along the line of lode for their hearty co-operation in its labours. It would also extend thanks to Messrs. J. O. Moulden, Howchin, Twelvetrees, and the West Australian Geological Survey for various information; to Messrs. J. G. Dreyer, S. Pope, T. Read, P. Moncrieff, R. Williams, and W. J. Rose for analyses; and to a number of local gentlemen for advice and help. Professor Skeats, of the Melbourne University, gave much valued assistance in petrology, and Mr. Herbert Lavers kindly undertook the study of the garnets.INTRODUCTIONThe famous Broken Hill lode is situated in a low range of hills, the Barrier Ranges, near the western border of New South Wales. It has been worked since 1884-first for, silver, then for silver and lead, and at present for lead, silver, and zinc. No excuse seems necessary for placing before members even an imperfect report on the geological features of this notable ore deposit, since so little work has been done on the subject as to constitute almost a national reproach. This is the more deplorablesince the evidence laid open by mining operations is destroyed almost as soon as it is exposed, and there exists the real need of a continuous and connected record of geologieal developments.

Jan 1, 1911

By L Manca, P B. Hills, D Tyler, N Pollington

This paper describes a collaborative project undertaken by Newcrest Mining Limited (Newcrest) and pitt&sherry to identify, develop and then implement global best practices to manage the exposure to inrush (dry and mud) hazards in underground mining operations. An extensive literature review was undertaken to identify past experience globally and the current state of knowledge and practice in managing inrush hazard. A key requirement of the literature review was the development of a list of guiding questions which would form a framework for approaching operators to discuss the topic, capture recent learnings and understand current operating practices to allow the development of a best practice solution. An initial cohort of 14 mines across four continents chose to contribute and detailed interviews were carried out by the project team. The outcome from the literature review, interviews with participating mines and various internal discussions was a comprehensive summary document detailing Basic versus Best Practice management of the inrush hazard. This document is being used as a gap analysis tool by Newcrest to assess and guide the management of inrush hazard at their existing and future operations. The summary document has also been provided to the participating mines for their consideration. The project is iterative and will continue to evolve as new experiences, knowledge and practices come to light.

Mar 15, 2021

By L Q. Amorim

The mining district of the Quadrilátero Ferrífero (QF) in southeastern Brazil contributes to 70 per cent of the Brazilian iron ore production, which reached 370 Mt in 2010. Traditionally, four iron ore types were mined in the QF region:1. soft haematite,2. hard haematite,3. friable ‘itabirite’ (the Brazilian name for metamorphosed banded iron formation), and4. canga (an indurated iron-rich crust).With the exception of the hard haematite, these categories derive from supergene enrichment of the Paleoproterozoic Cauê Itabirite. High current iron ore demand means that the QF high grade supergene ores will be depleted in a few decades. Consequently, several mining projects are being developed to exploit unenriched, fresh itabirite. Among them, the Mineração Usiminas Serra Azul project in northwestern QF is one of the most advanced. Four major itabirite types occur in the QF region:1. siliceous (or standard),2. dolomitic,3. amphibolitic, and4. magnetitic.The dominant type in Serra Azul region is a fresh siliceous itabirite, composed essentially of haematite, martite and quartz that averages 36 per cent Fe (51.5 per cent Fe2O3) and 47 per cent SiO2. The second type, the magnetitic itabirite, consisting of magnetite, martite, gruneritecummingtonite, quartz, dolomite, stilpnomelane, and subordinate haematite, is typically a strongly magnetic greenish banded iron formation with the iron grade varying between 25 and 35 per cent. Chemically, it differs from the siliceous itabirite due to the relatively high CaO, MgO and, consequently, high LOI contents. Together with supergene ores, fresh itabirites have been included in the ore reserves of the Serra Azul project. We anticipate that all the four types of fresh itabirite will be incorporated as ore in the QF region, causing a huge increase on the iron ore resources of the district, and representing enormous environmental and technological challenges for the local iron ore industry.

Jul 11, 2011

By V Shrotri L Muhmood, P Gandhre

The current work deals with the measurement of some thermophysical properties of Ca(NO3)2 based ternary nitrate molten salts as HTF (heat transfer fluid) / TES (Thermal Energy Storage) material for CSP (Concentrating solar power) plants. The density and viscosity of different compositions of the ternary salt mixture containing Ca(NO3)2, NaNO3 and KNO3 close to the liquidus has been experimentally measured. An attempt has also been made to measure the melting point of the salt using the cooling curve technique as well as Differential Scanning Calorimetry (DSC). Thermogravimetric analysis has also been performed to estimate the peak operating temperature of the salt. Compatibility of suitable pipe material (SS304) with molten salt has also been discussed. The salt mixture proves to be a viable alternative to the already existing HTFs like Therminol VP-1 (organic oil) or Solar Salt® in regards to its lower melting point, wider operating range, low cost, nontoxicity, sufficiently high density and comparable viscosity.

Jun 19, 2024

By M I. Pownceby, S Bhargava, F Charalambous, S McMaster, R Ram, J Tardio

"A key component of any geometallurgical investigation involves being able to predict element or mineral recoveries from simplified input data such as bulk chemistry and/or mineralogy. This relies on the metallurgist having access to accurate information regarding the chemistry of the ore and gangue minerals as well as the likely impact on processing/extraction caused by the impurities (present either as gangue or as substitutional impurities). In this study the chemical properties of two commercially important uranium minerals, brannerite (U4+Ti2O6), and uraninite (U4+O2), were characterised using X-ray diffraction (XRD), scanning electron microscopy (SEM), and electron probe microanalysis (EPMA). Significant levels of impurities were present in both samples with the uranium minerals deviating significantly from their ideal chemical formulae. Differences in chemistry were due to: cationic substitution decay of the uranium isotopes into radiogenic lead and other daughter products mixed uranium oxidation states post-depositional alteration.As well, the brannerite sample showed evidence of significant radiation-induced metamictisation. Leach tests to measure the ease of extraction of uranium from both samples were conducted over a wide range of conditions (temperature, acid concentration and oxidant concentration). For uraninite, the lower U dissolution rates observed in the natural sample compared to a synthetic UO2 sample were directly attributed to the presence of impurities. For brannerite, significant metamictisation of the natural sample led to enhanced U extraction rates compared to a heat treated fully crystalline sample. This study highlights the importance of detailed mineralogical characterisation studies in any uranium process mineralogy investigation as the compositional, textural and microstructural aspects of the main uranium phases present will likely play an important role in any process to extract uranium.CITATION:Ram, R, Charalambous, F, McMaster, S, Pownceby, M I, Tardio, J and Bhargava, S, 2013. Chemical and microstructural characterisation studies on naturally occurring uranium minerals - implications for processing, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 325-334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013