Search Documents

By William A. Edmiston, R. E. Grace

A simplified model for the theory of reaction rates near equilibrium has been applied to the reduction of wustite. A linear relationship between the net rate of reaction and the Gibbs free-energy change, ?F, is predicted. The reduction of wustite in H2 -H2O gas mixtures was studied with a microbalance technique at temperatures from 850° to 950 °C. The predicted model was found to be valid to -?F/RT = 0.1 or approximately -200 cal per mole away from equilibrium. ThE theory of reaction rates near equilibrium has been developed by a number of authors. Prigogine, Outer, and Herbo1 have studied the catalytic hydrogena tion of benzene in an attempt to deduce some intrinsic connection between reaction rates near equilibrium and thermodynamics. Manes, Hofer, and weller2 have derived more general expressions for reaction rates near equilibrium from classical thermodynamics. Hollingsworth3,4 has commented briefly on the work of Manes et al. Benson5 has summarized in a general way the results of the earlier contributions. It is the purpose of this paper to apply the theory of reaction rates near equilibrium specifically to the reduction of wustite in H2-H2O gas mixtures. The basic premise is that the reduction of wustite proceeds by a surface reaction, rather than by solid-state diffusion ,or gaseous diffusion. Richardson and Dancy6 and Gellner and Richardson7 have suggested that the reduction of wustite may be governed by iron diffusion in wustite. Mckewan8-11 has proposed that reduced iron layers on various oxides are sufficiently porous to offer a negligible impedance to the reducing gas. The linear motion of interfaces reported by McKewan and discussed by Themelis and Gauvin12 indicates the lack of diffusive control during reduction. The reduction studies of magnetite reported by Quets, Wadsworth, and Lewis13 give additional evidence that reduction rates are linear when the reaction products are porous and nonprotective. The interpretation of measurements reported in this paper is predicated upon a surface-controlled reduction reaction, at least in the earliest stages of reduction when the reduced iron layer is thin.

Jan 1, 1967

PRESIDENT. CHARLES F. RAND,1 NEW YORK, N. Y. PAST PRESIDENTS. CHARLES KIRCHHOFF,1 NEW YORK, N. Y. JAMES F. KEMP,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT. BENJAMIN B. THAYER,1 NEW YORK, N. Y. TREASURER. GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS. ROSSITER W. RAYMOND NEW YORK, N. Y.

Jan 5, 1913

PRESIDENT L. D. RICKETTS,1 NEW YORK, N. Y. PAST PRESIDENTS BENJAMIN B. THAYER,1 NEW YORK, N, Y. WILLIAM L. SAUNDERS,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS,1 NEW YORK, N. Y. TREASURER GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W.. RAYMOND NEW YORK, N. Y SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 6, 1916

PRESIDENT L. D. RICKETTS,1 NEW YORK, N. Y. PAST PRESIDENTS BENJAMIN B. THAYER,1 NEW YORK, N. Y. WILLIAM L. SAUNDERS,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS1 NEW YORK, '_N. Y. TREASURER GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 4, 1916

By O. W. Ellis

In view of the extensive use of the brasses and bronzes in engineering practice it is indeed surprising that so little scientific work has been done on the oxides in these alloys. Recognition of the ill effects of these compounds is universally accorded, both in foundry procedure and in such specifications as cover the melting of these useful mixtures. In the latter, limits, for example, are placed on the proportions of scrap metal In the charge, and clauses governing the use of fluxes are included, the addition of fluxes to the charge being made with the object of avoiding oxidation during the process of melting and of subducing and separating non-metal-lic matter from the melt.1 In the manufacture of brass it occasionally, though rarely, occurs that the virgin metals, copper and zinc, alone arc used. In the event of virgin metals being employed, that of the higher melting point is always melted first. If it is melted under suitable conditions, little or no oxidation will occur. Whether oxidation has occurred or not, however, can best be determined by microscopic examination of a sample taken from the melt. Avoidance of Oxidation in Furnace Practice When melting virgin copper in crucible practice, the avoidance of oxidation is not difficult, nor is it hard to forestall trouble in the electric furnace. In gas-fired furnaces of the barrel type, however, the avoidance of oxidation is almost impossible, no matter what the condition of the flame, the flux employed, or the amount of charcoal included in the charge. Copper melted in furnaces of this type is almost invariably so highly oxidized as to requirc very considerable additions of such deoxi-dizers as, for example, silicon copper to render it free from cuprous oxide. As a result,, the castings produced are decidedly inferior, on account of the. large amount of silica which is engendered in the metal as a result of the reaction, Cu2O + Si = SiO2 + 2Cu. The deoxidation of such oxidized copper could, of course, be effected by means of zinc with, however, even more disastrous results.

Jan 1, 1930

By N. B. Gray, R. V. Culver, W. S. Boundy, N. W. Stump

The kinetics of sulfation of single crystals of lead sulfide to lead sulfate have been studied between 969" and 1073°K in gas atmospheres of known composition using a thermobalance technique. The data are described by an equation derived on the basis that diffusion outward through the Product layer is the major controlling step. The rate of sulfation is linearly related to the logarithm of the sulfur trioxide partial DESPITE its industrial significance the oxidation of lead sulfide has received limited attention. The oxidation reactions have been studied using beds, briquettes, single crystals, or thin films of lead sulfide. Lead oxide and lead sulfate (PbSO,) were formed when Mclntoshl and Gardner2 roasted beds of galena pressure and the temperature coefficient of reaction is 40 ± 5 kcal per g mole. Gold marker experiments show that the sulfate layer grows by outward movement of ions through the sulfate layer. Initially the PbSO, adheres to the PbS but later forms an irnpewious spheroidal envelope; PbS vaporizes and pb2' ions diffuse through the envelope to react at the external surface. in air at temperatures up to 800°C. In a more extensive investigation, Tchizhykov3 obtained Pb, PbO, and PbS04 in accordance with Eqs. [1] to [4], when a bed of -200 mesh galena was oxidized in O2-N2 mixtures at 700° to 900°C.

Jan 1, 1968

By T. H. Ramsey, Richard Shield

A process has been developed for fabricating thin-film resistors that are compatible with integrated circuits. Films are produced by evaporation of single refractory metals using an electron beam heating source. Resistor paths are then made using standard photoresist etching techniques. A low-temperature coefficient of resistance is obtained by control of nucleation during deposition of the film. One application of the process has been the development of a discrete resistor used for current setting in linear integrated circuits. Multiple thin-film resistors were formed on oxidized silicon substrates using molybdenum metal as a source. An evaporated protective layer of SiO2 over the resistor prevents resistance changes which might occur during subsequent high-temperature processing. Properties of a typical resistor are as follows: R = 15.7 ohm per sq, tolerance surface dimensions = 0.028 by 0.028 in., stable after 4000 hr at 0. 75 w without heat sink. THIN-FILM resistors have been investigated for many years with a large selection of usable resistors resulting from a wide variety of materials. Many of the processes necessitate a high degree of complexity but in nearly all cases the conclusions have been that the materials used in each case were acceptable provided the deposition process was reproducible and could be controlled sufficiently to give the required tolerances. It is our opinion that simplicity is still the key to thin-film resistor fabrication. In this regard, the single metal is obviously the simplest process to control, provided all the necessary properties can be obtained. The idea is not original in this laboratory by any means. Others have taken this approach.' It has been demonstrated that a fairly wide range of resistivities can be obtained by careful control of deposition parameters for any given metal, and by selection of several single metals a very broad range of stable resistors can be obtained. The transition from one metal to the next is made when a film becomes too thin for adequate process control or long-term stability. A great deal of emphasis is once again being placed on the thin-film resistor. Although they have been thoroughly studied in the past, new applications have been found that require the properties obtainable only from thin-film resistors. Integrated circuits, in general, are advancing toward higher speeds and radiation environments which require replacement of the present diffused resistors. Linear circuits in particular are requiring high-power, high-precision resistors for the more advanced applications. The particular requirements of some linear circuits are such that a discrete resistor is required. The resistor described in this paper was developed as a 15.7-ohm precision discrete resistor for use in a current regulating circuit requiring a +2 pct end of life overall tolerance, a dissipation of 750 mw, and the ability to operate over a fairly broad temperature range (i.e., a low temperature coefficient of resistance, TCR). State-of-the-art integrated circuit and silicon processing technology lends itself well to the fabrication of thin-film resistors. Not only is the resistor thin film well-suited to integration on individual circuits, but the oxidized silicon surface provides one of

Jan 1, 1969

By V. W. Aubel

Among the iron-bearing ores of the world, the titaniferous iron sands of New Zealand are probably the least known to American engineers. This is not surprising in view of the fact that American ironmasters look with disfavor on any, even domestic, ores containing over 1 per cent. titanium. The possibilities of smelting titanium-bearing ores in the blast furnace are still undetermined, but the problem of their efficient reduction is becoming more important each year. There seems to be little inclination on the part of American furnace operators to tackle this problem, and they will no doubt continue to utilize the non-titanium ores at their command, leaving research and experiment to those countries not so fortunately endowed. New Zealand has, however, been intensely interested in her deposits of titanium-bearing iron sand, and during the last 50 years considerable English and New Zealand capital has been expended on this problem. The extent of the New Zealand iron-sand deposits is almost beyond measure. From Patea north to Manuka Heads, along almost the entire west coast of the North Island, these deposits exist. Wherever there is beach sand along this 300 mi. of coast line, the sand is iron bearing. It varies considerably in grade; but wherever the contour of the coast affords small bays and inlets, large dunes are found that are remarkably uniform in quality. Several of these large deposits, especially those at New Plymouth and Patea, are noted for their high iron content. The dune at New Plymouth runs between 55 and 60 per cent. of metallic iron; the panning action of the prevailing westerly winds and northwesterly currents has no doubt resulted in this concentration. Whatever the origin of this material may be, there is no doubt that deposition is going on continuously. At New Plymouth, a small artificial harbor, protected from the drifting sand by a large breakwall, has been dredged. Here sailing vessels have for years been loaded with iron sand for ballast by means of a crane and grab bucket operated from the wall of the breakwater. Thousands of tons of sand have been removed from this spot yet each succeeding storm renews the supply. The sand dune shown in Fig. 1 has been tested to a depth of 50 ft. (15 m.) without losing its

Jan 1, 1920

By C. D. Johnson

Exploration work in 1932 in the Rocky Mountain region, which includes the states of Montana, Wyoming, Utah, Colorado and New Mexico, resulted in the discovery of one new oil field, Cut Bank in Glacier County, Montana; one new gas field, Craig in Moffat County, Colorado; and the definite outlining of a second gas field, Piceance Creek in Rio Blanco County, Colorado, in which there had been drilled but one small gas well prior to 1932. During the year, 95 producing oil or gas wells were completed, giving new initial production amounting to 188,000,000 cu. ft. of gas and 176,420 bbl. of oil per day for the region. By far the largest part of this new production of both oil and gas was developed in southeastern New Mexico, mainly the Hobbs field. However, the Dry Creek field of Carbon County, Montana, contributed over 5000 bbl. of; new oil production. Sixty-two wells were abandoned during the year but of this number only 10 promising structures were nonproductive. The remaining 52 wells had little to recommend their drilling from a structural or strati-graphical standpoint. Eighty-eight wells were suspended in the region' during 1932 before the tests had reached their individual objective horizons. Many of these suspensions were due to financial difficulties and it is possible that several of the operations may be resumed at a later date. At the close of the year, 54 wells were actively drilling, 54 were shut down and there were 20 rigs and locations in the five Rocky Mountain states. The accompanying table gives details of drilling and production.

Jan 1, 1933

By J. C. De Haven, Harry Seltz

INTERMETALLIC compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points'. While the lattice structures of some of these compounds' have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455° C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52,b=8.60,c=4.16Å2 There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO2 = CdO + CO + Sb. From the known free energies of formation of, CdO, CO2 and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell

Jan 1, 1935

By Michael Chender

The current outlook for financing new copper production is not very encouraging. At a time when companies are slogging through a protracted period of low prices as well as having to accept lower profits due to more stringent tax and royalty schedules, banks are beginning to require companies to take a greater equity interest in new projects. Mineral resource financing, including copper, seems to have lost much of its appeal to the lending institutions, and loans of any kind to many of the developing countries -from which over half of new copper capacity could be expected to come-are being examined much more critically than they were in the late 1960's and early 1970's.

Jan 12, 1976

Feb. 5. Society for Applied Spectroscopy, 6 pm, supper, Tosca's; 8 pm, meeting, Socony-Vacuum Training Center, 63 Park Row, New York. Feb. 6, AIME, Chicago Section, Chicago Bar Assn., 29 S. La Salle St., Chicago. Feb. 18-21, AIME, annual meeting, Hotel Statler, New York. Feb. 19, Michigan College of Mining and Technology, alumni reunion, Skytop Room, Hotel Statler, New York. Feb. 21, AIME, Utah Section, Newhouse Hotel, Salt Lake City. Feb. 28, Bituminous Coal Research, Inc., annual meeting, Edgewater Beach Hotel, Chicago. Mar. 3-7, ASTM, spring meeting and committee week, Hotel Statler, Cleveland. Mar. 5, AIME, Chicago Section, Ladies' Night, Chicago.

Jan 1, 1952

By G. F. Dillion, A. F. Armington

THE present method for the ultrapurification of boron involves the formation, distillation, and decomposition of boron tribromide.' However, the boron tribromide prepared contains several impurities in the ppm range, even after distillation. Some of these impurities, notably carbon, can be reduced after decomposition by zone refining. In this study, a comparison of the purity of boron tribromide at various formation temperatures is presented. The apparatus employed consisted of a bromine flask connected to a 22 mm ID horizontal quartz reaction tube packed with amorphous boron powder, which was in turn connected to a receiving flask cooled with an ice bath. Argon was used as a carrier gas. The approximate rate of passage of bromine to the reaction tube was 25 g per hr. The reaction was first investigated at several temperatures in order to determine the lowest temperature necessary to produce a colorless product which was assumed to be an indication of complete reaction of the bromine. The lowest temperature found in this study was 420oC. The amount of impurities found in the boron tribromide at various formation temperatures is shown in Table I. The data presented are emission spectroscopic results of boric oxide produced by the hydrolysis of 2 to 3 g of boron tribromide in 10 ml of distilled water. After hydrolysis, the samples were dried several hours on a hot plate. Assuming equilibrium conditions in the reactor, one can make approximate thermodynamic calculations estimatling the completeness of reaction of bromine with boron and its impurities at various temperatures. Data for these calculations were taken from Rossini,3 and must be taken as approximations since the T?S factor was not included in the calculations. The results of such calculations indicate that, with the exception of carbon bromina-tion, all impurities would react almost to completeness (> 99 pet) at all temperatures between 400" and 900oC. In the case of carbon, which cannot be accurately analyzed spectroscopically, it is estimated that only about one sixth as much carbon tetrabromide would be formed at 400" than at 900°C. Since some marked reductions in impurity content were observed at the lower reaction temperature which would not be predicted by thermo-

Jan 1, 1962

By J. R. Cahoon, H. W. Paxton

The mechanical properties of unidirectionally solidified A1(rich)-Mg and A1(rich)-Cu castings containing up to 15 wt pct solute have been determined with re -spect to the volume fraction of interdendritic eutectic. Pioperties were determined in the directions pumllel and Perpendicular to that of solidification; the volume fraction of eutectic was varied between the "as-cast" and equilibrizcm amounts by approperiate heat treatment following solidification. The principles of fiber strengthened composites and dispersion strengthened materials are adapted to explain the mechanical properties of these castings. It is generally accepted that castings often have inferior mechanical properties when con~pared to wrought products. However, there is little quantitative data available concerning the factors which make apparently sound castings weak and/or brittle. The relative ease and inexpensiveness of the casting process have always been attractive and, therefore, an understanding of the factors which contribute to the mechanical properties of castings would seem desirable. Such an understanding may lead to an improvement in the mechanical properties to an extent where castings would become competitive in applications where presently only wrought products are considered to have the requisite properties. Such an understanding could also improve the reliability of present cast products. Much of the recent research on castings has centered about determining the extent of segregation in cast alloys. Macrosegregation, particularly inverse segregation, has been studied in some detail 1-8 and a considerable understanding of microsegregation has been obtained.9'10 The effect of solidification rate on dendrite spacing and on the amount of interdendritic eutectic in binary alloys has been established, particularly for Al(rich)-Cu alloys.""0 However, the extension of these ideas to relate the amount of interdendritic eutectic, concentration gradients, micro-segregation, dendrite spacings, and so forth, to the rnechanical properties has been limited. Dean and spear" have related the mechanical properties of an Al-Si-Mg alloy, A356-T62, to the dendrite spacing and have shown that the mechanical properties improve with decreasing dendrite spacing. Passmore et al.12 have shown that annealing at high temperature improves the mechanical properties of Al(rich)-Cu al- loys and Archer and Kempf 13 have shown that an Al-1 pct Mg-1.75 pct Si alloy behaves in a similar manner. Ahearn and Quigley 14 have shown that high temperature homogenization also enhances the mechanical properties of an SAE 4330 steel. However, in the above investigations, no underlying reasons were suggested for the improvement in mechanical properties. The purpose of the present investigation is to relate the mechanical properties of castings to some of the solichfication variables and to derive some equations by which calculations of the mechanical properties may be attempted. In particular, the effect of the amount of interdendritic eutectic and the effect of stress direction with respect to that of solidification on the mechanical properties will be considered. The Al(rich)-Mg and Al(rich)-Cu binary alloy systems were chosen for study. The A1-Mg system was chosen because its constitutional relationships are such that large volunles of eutectic (up to 24 vol pct) may be obtained in the as-cast condition and then be completely dissolved by subsequent heat treatment at about 440°C. This allows a comprehensive study relating the mechanical properties of castings to the amount of interdendritic eutectic. Also the Al(rich)-Mg eutectic is almost a single phase 15 which should make the experimental results more amenable to theoretical interpretation and calculation. The A1-Cu system was chosen for study because of the large amount of related information available concerning segregation, dendrite spacing, and so forth. Unidirectionally solidified castings were used throughout the investigation so that the effect of solidification direction with respect to the direction of applied stress could be determined. THEORETICAL It is well known that upon solidification of binary alloy castings, the nonequilibrium amount of eutectic which forms is given by 10 where fe o is the weight fraction of eutectic, Cs is the solid solubility of solute at the eutectic temperature, k is the equilibrium partition coefficient, and C, is the average composition of the alloy. In the development of Eq. [I], it is assumed that the effects of inverse segregation and diffusion in the solid are negligible, and that no porosity is present. If the casting is homogenized at a high temperature for a long period of time, some (or all) of the eutectic is dissolved and the amount of eutectic for this "equilibrium" condition may be calculated directly from the constitutional diagram. By appropriate intermediate annealing, the

Jan 1, 1970

By Geo. W. Goetz

The following tables show the analyses of ores from nearly all of the mines which will produce over 10,000 tons of ore each during the season of 1890. There are many small mines now in the course of development, some of which may become large producers. Many of the mines produce several different grades of ore, but the analyses given in the tables are fair averages of ore such as the respective mines can deliver. Most of these analyses were obtained from the agents of the respective ores, and are averages of the season of 1889. One can state positively that over 75 per cent. of all the iron-ores of the Lake Superior district will average over 60 per cent. of metallic iron. During the past 34 years this region has produced about 48,137,421 tons of ore, the different districts contributing about as follows: Marquette District,. 29,754,057 Menominee " .10,415,859 Gogebic " . 6,622,194 Vermilion " . 2,342,991 Miscellaneous,. .. .. 2,320 In the year 1889, the product of all the districts was nearly '1,300,000 tons. The product of the entire region for the season of 1890 may exceed 9,000,000 tons. This large amount of ore is shipped to the lower lake ports, from Escanaba, Marquette, Two Harbors and Gladstone.

Jan 1, 1891

By W. A. Backofen, D. Lee

Tlze condition of superplasticity or neck-resistanl flow that results front high strain-rate sensitivity has been observed in isothermal tension tests on several titanium alloys and one of zirconium hi general, il was associated with reasonably fine-grain micro-structures being stvained in the transformation range at rates below i - 10 -3 sec-&apos;. The metallographic mean-free path, L, was measured at room temperature after rapid cooling from the temperature of test-ing. The flow stress of Ti-GAL-4V at 950°C was proportional to La at different constanl <; the value of a decreased with increasing. E but at E< 1.5 x 10-4 sec-1 it varied only from 0.9 to 1.25. The findings were interpreted to mean that viscous boundary shear is the rate-controlling process of deformation at high levels of strain rate sensitivity in these materials. Elongation of over 1000 pet could be obtained, but a1 temperatures so high and rates so low that any practical application of the full effect would probably be difficult. As the transformation range was narrowed, by turning from Ti-6AL-4V to Ti-5Al-2.5sn to nomznally pure titanium, the allowable temperature varialion was correspondingly reduced. Superplasticily was not found in Armco iron, presumably because the transformation range was too narrow to allow the developtnenl of a reasonably stable microstructure for isolhermal lesting. THE work represented by this paper grew out of a recent study of texture hardening in a(hcp) titanium and zirconium-alloy sheet,&apos; of which part has now been published.2 It was found that, with heating, the tensile plastic-anisotropy index, R,* was decreased from well above 1 towards 1 as the temperature range for the a(hcp) -ß(bcc) phase change was entered. The clearest example of that trend is illustrated with previously unpublished data in Fig. 1. It might have been thought that such a development resulted simply from introduction of the cubic and therefore plastically less anisotropic phase. However, the accompanying change in the index of tensile strain-rate sensitivity, m = a log a/a log E, was rapidly upwards, to a high of 0.85 in some cases (also illustrated in Fig. 1). At the same time, the total tensile elongation rose to a maximum and the flow strength dropped away as R (and m) approached 1. Taken together, the observations cannot be understood as resulting from the presence of cubic phase, per se. It has been concluded instead that they reflect the largely noncrystallographic deformation which characterizes superplasticity. As demonstrated in other recent work? a necessary condition for super-plasticity is strain-rate sensitivity of flow stress sufficiently high that m is above a lower limit of -0.3. The origin of large m has been traced, in turn, to grain size so small that a substantial amount of viscous deformation is introduced by such processes as Nabarro-Herring diffusional flow4 and/or grain boundary shear.5,6 Because of problems in the processing of titanium and zirconium alloys—problems of high strength, limited ductility, and excessive springback, originating largely in slip resistance-it was natural to wonder if something useful might be done with superplasticity in those materials. Therefore experiments were made for more closely identifying and generally bounding the phenomenon with temperature and strain-rate limits, before attempting to decide about its exploitation. The results are being reported here. EXPERIMENTAL Materials. The two of primary interest were the titanium alloys of nominal composition (in wt pct) 5A1-2.5Sn and 6A1-4V. Others were a 4A1-1/4O2 titanium alloy, titanium of commercial purity (RC-70), Zircaloy-4. and Armco iron. All were received as annealed 3/16 in. thick sheet, except RC-70 which was & in. thick, and tested in that condition. Details of transformation temperature and grain size are given in Table I. The results of dilatometry for the measurement of transformation temperatures were unsatisfactory. Data were finally obtained by metallographic examination of each specimen after test, to determine from the amount of transformed 4 where the specimen had been heated in relation to the critical temperatures. Results were in reasonable agreement with information from the supplier. Strip tensile specimens were of full sheet thickness and taken along the rolling direction, except for those

Jan 1, 1968

By Oliver C. Ralston

THE two chemical compounds, natural sodium carbonate and sodium sulphate, in their anhydrous condition are dealt in as "soda ash and "salt cake”-names from an earlier day that are not as precise as the present accepted terminology. Once a large part of the sodium carbonate recovered was in the ash of seaweed, so it was logically called soda ash, and the corresponding potassium carbonate, once mainly recovered from wood ashes, was called potash. The term "salt cake" was applied to the sodium sulphate resulting from interaction of sodium chloride with sulphuric acid or sodium bisulphate, to form hydrogen chloride gas and an anhydrous cake of sodium sulphate. It was called "salt cake" and also "glassmaker&apos;s salt cake" because much of it was used in the production of glass. The two salts occur in nature in a variety of forms, but whereas an- hydrous sodium sulphate (thenardite) is fairly common, the anhydrous normal sodium carbonate, Na2CO3, is almost never found in nature. The monohydrate (thermonatrite), Na2CO3.2H2O, is seen occasionally, but it is never a major constituent in natural "soda" deposits. The high solubility of normal sodium carbonate is one reason for this. While both compounds occur widely in brines, the solid salts found in nature are usually trona (Na2CO3.NaHC03.2H2O) and thenardite (Na2SO4). The natural brines containing workable quantities of the two sodium salts are largely found in the arid and semiarid portions of the western United States and other countries. The classical discussion of the resources of these brines are those of Clarke,5 Chatard.4 Packard,19 Gale,11 and Wells.28 From North Dakota to California and from Arizona to the Canadian provinces of Alberta and Manitoba, saline lakes, dried-up lakes, playas, and similar land-locked depressions contain accumulations of saline matter. Sodium chloride is the predominant salt but some of the lakes contain predominantly either sodium carbonate or sodium sulphate. Often sodium carbonate

Jan 1, 1949

By E. S. Machlin, A. J. McEvily

HE results of an experimental investigation by McEvily and Machlin have indicated that a strong relationship exists between the processes of cross slip and fatigue. Whenever dislocations can cross onto an intersecting plane and expand thereon, as in AgCl crystals, the usual type of S-N behavior is obtained, but when such a process is difficult, as in NaCl crystals, fatigue does not occur in its usual manner, if at all. MgO, because of its crystal structure (NaCl type) and slip systems ({110}<110>) would not be expected to fail in fatigue. However, Cornet and Gorum2 have found something akin to the usual type of fatigue behavior for MgO crystals. The purpose of this note is to attempt to resolve this apparent discrepancy. In Cornet and Gorum&apos;s work as-cleaved crystals were tested under cyclic axial loading, whereas in McEvily and Machlin&apos;s work chemically-polished crystals were tested in reversed bending. Because of the difference in specimen preparation, the major effort of the present work was directed toward comparing the behavior of as-cleaved as opposed to chemically-polished specimens. The effect of type of loading seemed less important, but a check was made on this also. Eighteen bend tests and one axial load test were made. The specimens were cleaved from Norton magnorite blocks, and measured 1 by 3/16 by 1/8 in. To avoid failures in the grips, the thickness of the bend specimens was reduced from 1/8 in. near the ends to 0.04 in. in the central portion. This reduction was from one side of the crystal only. Twelve specimens were polished in orthophosphoric acid to remove the damage due to cleavage. The other six specimens were not chemically polished so as to maintain the as-cleaved condition of the crystal faces which had not been reduced. The axial-load specimen was reduced from both faces to a thickness of

Jan 1, 1962

By Joseph Singewald

THE problem of the utilization of the low-grade red iron-ores has peen before the iron-mining industry of the South for several decades. the experiments by W. H. Coghill1 of the U. S. Bureau of Mines to determine the degree of liberation of minerals in the Alabama low-grade red iron-ores after grinding interest the writer very much because 10 fears ago, while a member of the U. S. Bureau of, Mines, he experimented similarly on the same ores using a heavy solution .2 Extensive experiments were made in the nineties by W. B. Phillips3 in association with H. A. J. Wilkens and H. B. C. Nitze. The ores were rushed to pass 15 mesh and were separated by magnetic machines into concentrates, middlings and tails. The experiments were made with carload lots in an experimental mill. Most of the ores tested, however, were soft, whereas the main problem is the utilization of the low-grade hard ores. Phillips gives the results of only four tests of hard ores; two of these are of self-fluxing ores of the grade now utilized and two of ower grade and less amenable to concentration than the average low-grade ore that underlies the self-fluxing ore of the Big Seam. The average of these least favorable samples shows the production, from an ore analyzing 32.30 per cent. Fe, 10.34 per cent. CaO, 33.40 per cent. insoluble, of a concentrate with 43.82 per cent. Fe, 8.90 per cent. CaO, 18.48 per Sent. insoluble with a ratio of concentration of 2 and an iron recovery of 39.2 per. cent. The grade of this concentrate compares favorably with the average grade of washed brown ores of the district which is given by Burchard4 as 45 per cent. Fe, 14.6 per cent. Si02. The slightly lower iron

Jan 2, 1927

By Olav Dalen

A HUNDRED years have passed since Wöhler made the first few particles of aluminum by decompos-ing aluminum chloride with potassium. In 1854 Deville used sodium to decompose the double chloride of aluminum and sodium, but even various subsequent improvements of the process, especially by Castner, did not sufficiently decrease the cost of the metal to bring it into general use. In 1862 Monckton proposed to reduce Al O? with carbon by the aid of the electric current, but the efforts of the Cowles brothers to do so were not successful and in 1884 they turned to making aluminum alloys by electrolysis. At about the same time Hall in America and Heroult in France success-fully worked out the technology of dissolving A12O3 in fused cryolite and electrolyzing the bath. It is hard to realize that forty years ago the annual production of aluminum was only 30 to 40 tons per year and the price of the metal thirty times what it is today. Great strides in decreasing the cost of production, improving the quality of the metal, and increasing the output have been made in the lifetime of middle-aged men. The large consumption of electrical energy in the form of direct current makes it necessary to locate aluminum-producing plants near waterfalls, to avoid transmission losses. Norway with its abundant water-falls is therefore a logical place for the development of aluminum production, even though it is necessary to import the bauxite, which is the raw material of the process. It was foreigners who first started the aluminum in-dustry of Norway and the first two plants were built by the British Aluminium Co. in 1906 to 1908; one at Vigeland near Kristiansand, and the other at Stavan-gerfjord in Nordfjord. These two plants are still oper-ating and producing over 3000 tons a year. When the plant at Vigeland is enlarged the production of the company will be more than 4000 tons a year.

Jan 11, 1927