Search Documents

By V. A. Phillips

Transmission-electron micrographs of electro-thinned samples of bulk-aged Cu-3.1 pet Co alloy show an aging sequence, supersaturated solid solution — coherent particles — quasi -coherent particles — noncoherent particles. Hardening is due to precipitation of coherent spherical fee coball-rich particles showing coherency strain fields, which are resolved at between 15 and 30A diameter. Loss of- full coherency did not occur until well into the overaged region, even with the assistance of deformation after aging. Different average particle diameters of 123, 92, and 149 ± 10Å were observed in samples aged to peak yield strength at 600°, 650°, and 700°C, respectively, indicating that there is no critical size for peak hardening. Noncoherent particles tended to develop (111) faces and became octahedral in shape. Dislocations tended to nucleate spherical coherent particles which eventually grew together forming large elongated particles. The surface energy of a noncoherent (low-angle) inter-phase boundary is estimated to he about 50 ergs per sq cm. A number of particle lining-up phenomena were observed. Overaging is principally attributed to increase in particle spacing, progressive loss of coherency, and increase in amount of discontinzdous precipitation. COPPER dissolves about 5.6 at. pet (5.2 wt pet) of cobalt at 1110oC1 and the solubility decreases to 0.75 at. petl (0.54 at. pet)2 at 650°C and to 0.1 at. pet or less at lower temperature.' It has been known for many years3-5 that Cu-Co alloys are capable of age hardening. Since cobalt is fee above 417°C and its atom size is only about 2 pet smaller than that of copper, precipitation of coherent particles would be expected. The equilibrium phase precipitated at 700°C and below contains about 10 pet Cu in solution which tends to stabilize the fee structure, lowering the transformation temperature to 340oc.l The alloy is known to undergo discontinuous precipitation in addition to general precipitation; while the former can be seen with an optical microscope, the latter precipitates are not visible except in the grosly overaged condition.5, 6 Extensive use has therefore been made of the ferromagnetic properties of the precipitate in order to follow the course of aging, and it has proved possible to measure the average particle size, spacing, approximate shape, and volume fraction and to determine that the particles are coherent without ever seeing a particle (see for example Refs. 2, 7, and 8). The magnetic measurements of particle size are limited to diameters below about 120Å.7 The present study was undertaken using the techniques of transmission-electron microscopy in order to check the above conclusions, to extend the previous magnetic work to larger particle sizes, and to attempt a more detailed correlation of properties and structure. A portion of this work has already been published.9-11 The present paper is concerned with the metallographic features of precipitation in relation to aging curves. Bonar and Kelly12'13 have published preliminary results of a similar study on single crystals of Cu-2 at. pet Co. EXPERIMENTAL Preparation of Alloy. A Cu-Co alloy, containing 3.12 wt pet (3.36 at. pet) Co by analysis, was prepared from 99.999 pet purity oxygen-free copper and electrolytic-grade cobalt. The alloy was melted and cast in vacuo in a high-frequency furnace using a graphite crucible and mold: Analysis showed chat 0.004 pet C was picked up during melting. The 1-1/2-lb ingot was homogenized in hydrogen for 24 hr at 1000°C. Slices were cold-rolled to 0.005 or 0.003 in. thickness, with an intermediate 650°C anneal in hydrogen at 0.080 in. thickness. Batches of six to ten strips were solution-treated in sealed-off quartz tubes in high vacuum in a vertical furnace and quenched by dropping into iced brine containing a device which snapped off the nose of the tube. Solution treatment consisted of 1 hr at 990°C or 2 hr at 965°C. The latter was employed for all mechanical-property studies, since a tendency was noted for the higher temperature to give porous material. Strips were usually aged individually in a horizontal vacuum furnace, inserting into the hot zone and withdrawing into a cold zone without breaking the vacuum. This method gave a rapid heating rate, permitting the use of short aging times. In some cases, particularly for the longer aging times at the higher temperatures, samples were sealed individually in quartz tubes in high

Jan 1, 1964

By C. E. Cannon, R. C. Craze

This paper discusses the results of a study of reservoir pressures in the Gulf Coast area of Texas and Louisiana, showing the general relation of the reservoir pressure to its subsea depth, as well as excessive reservoir pressures that have been encountered. The latter are particularly important in mud-control work, and the data show why it is necessary to use muds having a relatively high density in many of the deeper wells drilled in this area. Only a comparatively few of the wells drilled in the Gulf Coast that have encountered excessive pressures are discussed, but as far as is known those omitted fall within the range of pressure observed by the writers. Measurement of Pressures The following methods were used to determine the values of the original pressures: 1. Estimation of original pressure from subsequent pressure behavior of fields. This method is not precise, and was used only in a few of the older fields in which better methods of obtaining original pressures were not available. Only normal pressures were determined by this method. 2. Measurement of shut-in pressures soon after completion of the first producing well. With one exception, all pressures measured by this method were normal, this well having a pressure slightly higher than normal. 3. Measurements of pressure in connection with drill-stem tests. 4. Estimates from the maximum hydrostatic head of mud that failed to prevent flow from the high-pressure formations into the hole. This method is not exact, tending generally to indicate low pressures. Normal Pressures All pressure measurements available are plotted in Fig. 1, with original pressure at the water-oil contact as abscissa and subsea depth as ordinate. All producing fields fall close to the solid line, which passes through the origin and has a slope of 0.465 lb. per sq. in. per ft. By way of compari-

Jan 1, 1938

By A. U. Seybolt

The solubility of oxygen in a iron has been determined in the range between 700° and 900°C. The solubility is a function of temperature and varies from about 0.008 pct oxygen at 700°C to atureandabout 0.03 pct at 900°C. The heat of solution is approximately +15,500 cal per mol. AS pointed out in a recent paper by Kitchener et al.,1 there has been a lack of agreement among many investigators even as to the order of magnitude of the solid solubility of oxygen in the various forms of iron. This lack of agreement is attributable in large part to the difficulties in the determination of a small oxygen solubility; but because the problem has remained so long unsettled, it also indicates a lack of interest which is rather surprising when the demonstrated importance of small amounts of soluble nonmetallic impurities in iron is considered. The work of Kitchener et al. apparently leaves the solubility of oxygen in iron in a satisfactory state, but no attempt was made to investigate the solubility in a iron. The solubility of oxygen in a iron is actually of greater interest, since it is in this form that iron and mild steels are employed ordinarily. That the effect of oxygen in iron is of more than theoretical interest has been well established by Fast,' and more recently by Rees and Hopkins," who demonstrated that oxygen in the range between 0.0008 and 0.27 wt pct has a pronounced effect upon the mechanical properties. Previous Work and Methods Used To report in detail the literature relating to the solubility of oxygen in a iron would require an inordinate amount of space. For those interested in reviewing this work, a bibliography4-13 of the more significant papers is appended. In general, two methods of studying this problem have been used. One is the gas-metal equilibrium method where the H2O-H2-Fe or the CO2-CO-Fe equilibria have been used. The other is the more direct approach of the oxidation of thin strips of pure iron by packing in mill scale or by air or gaseous oxygen at some desired temperature. In this method oxygen is allowed to oxidize the surface and then to diffuse inward until saturation is obtained. In the gas-metal equilibrium method the oxygen dissolved in solid iron at a given temperature is proportional to the ratio of the water vapor-hydrogen pressures or the CO2-CO pressures over the sample for small ratio values. If the ratio becomes higher than a critical value, then an oxide phase makes its appearance (the solution becomes supersaturated). In principle, it is possible to use a series of H2O/H2 or CO2/CO ratios and to find by analysis the corresponding amounts of oxygen in solid solution at constant temperature. At the point where a very small increase in the gas ratio (increase in oxidizing powder) produces a large increase in oxygen content, the solid solubility limit is reached. Alternately, if the critical ratio is known, it is possible to use the procedure of Kitchener et al.1 and to use a ratio which is near but below the critical one. The solubility corresponding to this lower ratio will not be the saturation solubility at the temperature employed, but the saturation solubility can be calculated by multiplying the measured solubility by the critical ratio over the ratio used. However, in the case where oxygen gas is the oxidizing medium, the saturation solubility is not a function of pressure, providing the pressure exceeds the dissociation pressure of FeO in equilibrium with iron. This is 1.2x10-16 mm at 800 °C, according to Dushman." As pointed out by Darken17 in discussing the FeO phase diagram, most of the possible errors tend to yield high values of oxygen solubility. For example, one circumstance which evidently caused the reporting of many high values was the use of finely divided or powdered iron in the gas equilibrium method. Because of the large surface area of such a sample, and the likelihood of some surface contamination if only by exposure to air, the results tended to be high. The direct oxidation method which was used in this work has the advantage in that it is simple and direct, but it suffers from one disadvantage: equilibrium can only be approached from the low oxygen side. The important factors to be kept under control are the following: 1—use of high purity iron to avoid internal oxidation (oxidation of readily

Jan 1, 1955

By Ernest P. Hall

At the SME Fall Meeting held in Phoenix, Ariz. last October, Ernest P. Hall, addressing an Air and Water Pollution session, noted that water pollution caused by acid drainage from bituminous coal measures had begun long before recorded history. "Until recently," he said, "man did not begin to understand the physical phenomena which took place to cause [it] and even today he does not know what can be done to prevent it." CAUSES "It is known from the reports of early explorers that drainage from bituminous coal measures was causing water pollution before coal mines were opened on this continent. They noted the nature of the polluted water in the runs and creeks and predicted the presence of substantial deposits of coal based on the appearance and character of the water. Even today, polluted water drains from virgin coal areas which have not been touched by mining machines," Mr. Hall said.

Jan 1, 1966

By H. C. Gatos, J. T. A. Pollock

It is well known that the superconducting critical current densities of many alloy superconductors may be increased by cold working and in some cases further enhanced by a short heat treatment. This latter enhancement has been attributed to the redistribution of dislocations into cell-like networks' and to the precipitation of second phase particles,2'3 which act as flux pinning centers. In a manner analogous to dislocation pinning in precipitation hardening alloys,4 it is expected that here also a critical distribution of the pinning centers should result in maximum pinning effect. Concentration inhomogeneities exist in most or all commercial alloys yet there have been only a few attempts made to determine their effect on critical current capacity in the absence of cold working. Sutton and Baker,5 and Kramer and Rhodes6 have found that the complex precipitation processes occurring during the aging of Ti-Nb alloys can result in critical current density enhancement. Livingston7-10 has clearly shown, for lead and indium based alloys, that the distribution of precipitated second phase particles is of critical importance in determining magnetization characteristics. However, these '(soft" alloys age at room temperature and the time involved in specimen preparation prevents metallographic examination in the state in which the superconducting measurements are made. Thus results with such alloys are expected to be biased towards larger precipitates and interpar-ticle spacing. The present study of Ta-Zr alloys was undertaken to examine the influence of second phase precipitation, as controlled by heat treatment, on the critical current capacity of well annealed polycrystalline material. A study of the published phase diagram11 indicated that annealing supersaturated samples containing up to 9 at. pct Zr at suitable temperatures would result in the precipitation of a zirconium-rich second phase. It was MATERIALS AND PROCEDURE The alloys were prepared from spectrochemically pure tantalum and zirconium. Analysis was carried out by the supplier. Major impurities in the tantalum were: 12 pprn of 02, 17 pprn of N2, 19 pprn of C, and less than 10 ppm each of Mo, Nb, Al, Cr, Ni, Si, Ti. The crystal bar zirconium was pure except for the following concentrations: 15 pprn of 02, 17 ppm of C, 23 ppm of Fe, 11 ppm of Cu, and less than 10 pprn each of Al, Ca, N2, Ti, and Sn. Samples were prepared in the form of 8 to 10 g but-tons by arc melting using a nonconsumable electrode on a water-cooled copper hearth in a high purity ar-gon atmosphere. Each button was inverted and re-melted three times to ensure an even distribution of the component elements. The samples were then homogenized at temperatures close to their melting points for 3 days in a vacuum furnace maintained at 5 x 10-7 mm Hg. After this treatment the buttons were cold rolled to sheets approximately 0.020 in. thick from which specimens were cut, 0.040 in, wide and 1 in. long suitable for critical current density (J,) and critical temperature (T,) measurements. These strips were then recrystallized and further grain growth was allowed by an additional vacuum heat treatment at 1800°C for 60 hr. Some second phase precipitation occurred during cooling of the furnace and a solution treatment was necessary to produce single phase supersaturated samples. This treatment was successfully carried out by sealing the samples together with some zirconium chips in quartz tubes under a vacuum of 5 x 10-7 mm Hg, heating at 1000°C for 5 hr and then quenching into water or liquid nitrogen. The samples were then heat treated at either 350" or 550°C and quenched into water or liquid nitrogen. All samples which were heat treated at 350°C were quenched in both cases by cracking the capsules in liquid nitrogen. The samples treated at 550°C were quenched by dropping the capsules into water. Analysis for oxygen in randomly selected samples indicated that the oxygen content was in the range of 175 to 225 ppm. Values of Tc were determined by employing a self-inductance technique. Jc measurements were made at 4.2oK by increasing the direct current through the wire in a perpendicularly applied field until a voltage of 1 pv was detected with a null meter. The risk of resistive heating at the soldered joints during these latter measurements was reduced by first plating the ends of the wires with indium and then soldering to the copper current leads using tin. Metallographic examinations were performed after mechanical polishing of the same samples and etching in a 4H20:3HN03 (conc):lHF(conc) solution.

Jan 1, 1970

By John Garcia

THE presence of carbon de terre along the banks of the Illinois river was noted by the members of the Joliet and Marquette expeditions in 1673, and that may be referred to as the birthday of coal in the Middle West. The march of progress in the majority of indus-tries radiating from Chicago-one of the phenomena of history-is due in no small measure to this same carbon de terre and to the development and exploita-tion of the vast coal resources, which nature in a generous mood spread so lavishly over almost the en-tire state. The geological records indicate that coal-bearing rocks underlie three-quarters of Illinois, in-cluding 85 of the 102 counties and the entire area is estimated at from 36,000 to 42,000 square miles. Not all of the coal in this great area may be mined under the conditions existing today; producers are now taking the "cream" since industry demands the best quality and the lowest cost, thereby forcing competition among operators, which, in turn, com-pels the development of mines in those areas where the coal may be most readily .won, leaving the coal that is more difficult and expensive to mine to pos-terity. This is not such a bad arrangement, since the engineers of succeeding generations will enjoy the advantage of the experience of their ancestors, where-by they should profit and know how to mine a 2-ft. seam with as much economy and dispatch as we today work coal of thrice that thickness. During the period between 1830 and 1850, Illinois coal-mining progressed from the art of scratching along the outcrop to the development of small mines, mostly slopes, drifts and shallow shafts, but the real progress in the industry was coincident with the con-struction of railroads.

Jan 2, 1927

By Milton H. Fies

THE Alabama Power Co. operates its Gorgas mine in Walker County, Ala., immediately adjacent to its steam plant. The coal mine property consists of some 19,000 acres of fee and mineral ownership lands, and all of the production from the mine-approximately 2500 tons per day-is utilized at the company's adjoining steam plant. The company is presently considering the purchase of additional acreage adjoining its present holdings which acquisition will almost double its reserves. The coal is transported from the mine over a short railroad spur in the company's own equipment, either directly to one of the large plants at Gorgas or to a storage pile. The longest haul is about 1 1/4 miles.

Jan 12, 1950

By Donald M. Hausen

Microscopic evaluation of trace quantities of metalliferous phases in flotation products requires counting large numbers of particles. Particle counts of many thousands may be required for precision, but cannot be obtained practically by conventional microscopic techniques. A less tedious microscopic method for evaluating trace sulfides in mill tailings was developed for the O'okiep Mining Co. in South Africa. Hundreds of thousands of particles were evaluated by this method called "gross-counting." Gross-counting consists of counting microscopic fields rather than point-counting individual particles. Total counts are calculated by multiplying the average number of particles per field by the total number of fields examined over the entire mount. Total gross-counts range from about 20,000 particles for +200 to 100,000 or more for -400 mesh size material in lucite mounts. Sulfides and metallic particles in each field are identified and tallied along with field counts. Totals for each type of metallic particle are divided by the total gross-count to give volume percent which is corrected to weight percent by specific gravity factors.

Jan 1, 1973

By H. D. Wilde

GREAT emphasis is being placed today on petroleum as a source of chemicals. Such prominence is well merited, for rapid strides have been made in developing processes for the conversion of petroleum into synthetic chemical products, which are now being made on a huge scale. These marvelous accomplishments have resulted in some highly optimistic predictions as to what can be expected in the future. Many of these forecasts are well justified, but some writers, especially those contributing to the Sunday supplements and the popular-cience type of publications, have let their imagination run wild and present a rather distorted picture of the possibilities in this field in the postwar period. Commercial manufacture of synthetic organic chemicals had its beginning in England with the establishment of a plant by Sir William Perkin in 1857 for the manufacture of "Aniline Purple" or "Mauve." The preceding year he had discovered in the laboratory how this dyestuff could be made from aniline, one of the many derivatives of coal tar, and he soon made commercial application of his discovery. Influenced largely by his success, organic chemists began research on production of a vast array of synthetic dyestuffs, medicinals, flavors, scents, and explosives. Rapid progress was made and by the turn of the century hundreds of these products were being manufactured. Most of these synthetic chemicals were derived from materials obtained as by-products in the conversion of coal into coke. These by-products are generally referred to as "aromatics" and are obtained by processing coal tar recovered in the coking process, so they are popularly known as "coal-tar chemicals." During the early years of this century, coal-tar chemistry was the wonder of the age, and rightfully so, since the products so made seemed limitless.

Jan 1, 1944

By H. W. Hitzrot

THE new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addi-tion of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis-charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure-the new fine-ore bin designed and built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work.

Jan 1, 1939

By L. W. Reynolds, R. F. Campbell, K. G. Carroll, S. H. Ballard

Based on metallographic and X-ray data probable equilibrium conditions from 1340" to 2400°F are presented for the composition range investigated. These are correlated with investigations of Takei and Kuo. Provision is made for existence of Mo, C and (Fe, Mo)2,C, carbides heretofore omitted in diagrams in this composition range. These carbides and (Fe, Mo),C, in equilibrium with ferrite and austenite, restrict the austenite and austenite + ferrite fields to lower carbon contents and higher temperatures than in the Fe-C system. OK groups of steel of different molybdenum content, but with approximately the same carbon variation in each group, Table I, were studied. The alloys were melted in an acid-lined 30-lb high-frequency induction furnace, and the ingots forged to l-in. rounds, which were then ground to 0.75-in. diam. To minimize chemical segregations a short length of each bar was given a high-temperature heat treatment as listed in Table I. Specimens 0.062 to 0.125-in. thick were thereafter cut from the homogenized bars for heat treatment to determine phase changes in the alloy. Heat treatments were performed in either a lead bath or muffle-type electric furnace, depending upon the temperature required. Maximum temperature variation was * 2" F in the lead bath and * 5"F up to 1900°F and +8"F above 1900°F in the electric furnace. Adequate protection of the specimen from the oxidizing atmosphere in the electric furnace was obtained by sealing the specimen in either a pyrex or a silica capsule which was evacuated or not as circumstances required. For austenitizing followed by quenching to an isothermal temperature, the specimen was placed in a closed-end refractory tube the mouth of which, extending beyond the furnace, was connected to a vacuum pump. The specimen could be withdrawn from this tube and quenched as desired. IDENTIFICATION OF PHASES The principal method of identification of phases was metallographic examination conducted on surfaces well removed from exposure to lead or atmosphere effects during heat treatment. Hardness measurements (Dph/lOkg) were also made on these surfaces. The etching reagents used and their effects are listed in Table II. Martensite and ferrite were readily recognized by their customary appearance after etching with saturated picral or 1 pct nital. The presence of liquid at high temperature was indicated by curved interfaces characteristic of boundaries between solid and melt, by intergranular pools of dendritic areas in a carbide matrix, and by a black network coincident with austenite grain boundaries. Examples of these structures are shown in Figs. l(a) and (0). The types of carbide which were attacked by the electrolytic chromic acid etch and the alkaline KMnO, etch, Table 11, were identified by X-ray analyses of extracted carbides of five alloys. Carbide residue was obtained from a metallographic specimen by etching the specimen for 24 hr in hydrochloric-picric acid in alcohol (grain-size reagent), after which the carbides, standing in relief, were scraped from the surface of the specimen and mounted on a glass slide. Diffraction patterns were obtained with a Philips spectrometer using iron-filtered cobalt radiation. Figs. 2, 3, 4, and 5 illustrate typical etching behaviors with chromic acid and alkaline KMnO,. Chromic acid attacked Mo,C as shown in Figs. 2(a) and (b)-but not (Fe, Mo),C, Fig. 3(b). Alkaline KMnO, attacked (Fe, Mo),C, Fig. 3(c), and also attacked M0,C. In accordance with these behaviors, a typical differentiation of coexisting Mo,C and (Fe, Mo),~ is shown in Figs. 4(a) and (b). The carbide (Fe, Mo),,C, could not be obtained free of other coexisting carbides for etching experiments. The behavior. however. of coexisting carbides identified by x-ray diffraction as Mo,C ind (Fe, Mo),,C, indicate that (Fe, Mo)23C6 is not etched by chromic

Jan 1, 1961

By Paul A. Farrar, Harold Margolin

The Ti-Al-V system has been delineated from 50 to 100 wt pct Ti and front 600 to 1400°C by X-ray and ntetallographic techniques. Isothermal sections were delineated at 600, 700, 800, 900, 1000, 1100, 1200, 1300, and 1400°C. X-ray and metallographic evidence indicated the presence of two phases and in addition to those reported by previous investigators of the ternary system'-3. T HE titanium-rich region of the Ti-Al-V system as originally proposed by Rausch et UZ, and Jordan and Duwez3 was based on the binary Ti-Al diagram as proposed by Bumps et uZ. As additional phases have been shown to exist5-' in the region previously thought to be all a, the titanium-rich region of the Ti-Al-V system is open to serious question. Therefore, in order to determine the effect of the indicated changes in the Binary Ti-Al system on the ternary Ti-Al-V system the present investigation was initiated. EXPERIMENTAL PROCEDURE The experimental procedures in this investigation are the standard techniques used in the study of titanium-alloy systems which have been described in detail previously.1° Consequently, only details pertinent to the present work are discussed. The alloys employed for the delineation of this system were prepared from titanium obtained from the Bureau of Mines (73 BHN) 99.99 pct Al and 99.7 pct V, by the consumable arc-melting technique. The titanium was premelted into buttons of 25 g because spattering during the first melt caused uncontrollable loss of alloying constituents. Typical analyses of the material used have been reported elsewhere Attempts to hot roll the alloys prior to heat treatment were made on the first series of alloys prepared, but as the area of extensive hot workability was fairly restricted, see Table I, this practice was discontinued. The times of isothermal annealing are given in Table 11. A preliminary heat treatment of 96 hr at 1000°C was used prior to heat treatment at lower temperatures. The standard techniques used for polishing specimens involved belt-grinding, grinding on emery paper, polishing electrolytically, and etching with Remington "A" etch. In the low-alloy region it was found that the oRo etch, developed by Ence and Margolin,o gave better contrast between phases. Where this procedure did not differentiate between phases clearly, the method of stain etching developed by Ence and was used. It has been previously reported15 that filing of titanium alloys is not desirable for producing X-ray powders, since the powder becomes contaminated by the file material. Therefore, for those samples not brittle enough to Crush, the procedure described below was used. The specimen was wrapped in molybdenum sheet and placed in a vacuum system and evacuated to 0.03 p. Palladium-pur if ied hydrogen was then admitted to the system until a partial pressure of 5o Cm of H was reached. The specimen was heated in the system to the temperature of original heat treatment and was slowly cooled over a period of 3 hr to 400°C while the partial pressure of hydrogen was maintained. The sample was removed from the system after it had completely cooled and was crushed to a powder of 230 to 270 mesh. The powder, wrapped in molybdenum sheet, was dehydrogenated at the temperature of original heat treatment until a partial pressure of 0.03 p was maintained in the system for at least 1/2 hr. The tube containing the powders was quenched in iced brine while still connected to the vacuum system. After dehydrogenation, the powder, except for the

Jan 1, 1962

By R. W. Raymond

The death of Professor Blake removes the oldest of American economic geologists and mining engineers, and deprives this Institute of one of its earliest and most illustrious members. To many of us it brings a personal loss also, the loss of a friend. William Phipps Blake was born June 21, 1826, in New York City. His father, Elihu Blake, was a surgeon-dentist of eminence, a direct descendant of William -Blake, who settled in the Massachusetts Bay Colony about 1630. He was prs pared for college at private schools in New York, and entered the Sheffield School of Yale, where he was graduated as Ph.B. in the chemical course, class of 1852, the first graduating-class of the institution. In the same year he became chemist and mineralogist of the New Jersey Zinc Co., and chemist of chemical works at Baltimore, Md. In 1853, he started the Department of Mineralogy of the World's Fair at New York City. In 1854, 1855 and 1856, he was mineralogist and geologist of the United States Pacific Railroad Surveys of Willianlson, Pope, and Whipple, and for the War Department at

Jan 1, 1911

By W. Luyken, E. Bierbrauer

A number of articles have been published, notably those by R. S. Handy, R. T. Hancock and A. P. Watt in Engineering and Mining Journal, dealing with the calculations involved in ore dressing. These publications demonstrate both the importance of the subject and the lack of success in developing a generally recognized method for comparing enrichment effects. Considering that we may wish to compare enrichment results on similar or dissimilar ores, that we may desire to make the comparison on the basis of either the absolute or the economical efficiency, and that the number of factors upon which the result depends is large, the question arises whether it is possible to set up a positive method for such calculations. In the following pages it is our aim to show that a sure, complete and successful way to overcome existing difficulties has been found. Graphical Analysis of Ore-dressing Processes The following is from Truscott's Text Book of Ore Dressing (London, 1923): x = assay of ore treated (feed). y = assay value of the concentrate. 2 = assay value of the tailing. a = weight of feed. 6 = weight of concentrate. c = weight of tailing. C = fractional concentration = = . a y - z K = ratio of concentration = 1/c a/b = y-z/x-z 2 B = fractional recovery = 9 = C y/x (3) 100R = percentage recovery. Copt. = theoretically best concentration. 100 — Copt = waste in the feed.

Jan 1, 1930

By R. Stefanko, Y. J. Wang, H. R. Hardy, R. Y. Kim

Since 1964, the Dept. of Mining at The Pennsylvania State University has been carrying out extensive studies associated with the phenomena of microseismic activity and inelastic behavior in geologic materials. Briefly, the program to date has involved the following stages 1) Study of the microseismic noise and energy rates for selected geologic materials under incremental, uniaxial tension.1,2 2) Investigation of the frequency spectra of microseismic activity of selected geologic materials under incremental, uniaxial tension.3,4 3) Investigation of the time-dependent inelastic deformation of geologic materials and the analysis of such deformation in terms of mechanical models.5, 6 4) Simultaneous study of microseismic activity and time-dependent inelastic deformation in geologic materials under incremental, uniaxial compression.7,8 Details of the research involved in stage 4 of the program constitute the subject of this chapter. It should be noted that the majority of the experimental data quoted in this chapter forms part of a thesis to be presented by one of the authors (Kim) in partial fulfillment of the requirements for the Ph.D. degree in mining engineering at The Pennsylvania State University. During the last two or three years, a number of important papers have been published which deal primarily with the fundamental structure and mechanical behavior of geologic materials. Recent papers 9,10 have provided research workers in the rock mechanics field with a meaningful overall picture of rock as a structural material. The concept that many

Jan 1, 1970

By Wendell E. Dunn

INTRODUCTION The early history of the chloride process has been recorded in a chapter of a Bureau of Mines bulletin (9 by one of the inventors of a chloride process, Stewart Croasdale, who is famous for the Pohle- Croasdale Process. The earliest use of chlorine in metallurgy was in 1557 by Bartholome Medina. But apparently even earlier there was knowledge that salt could be used in gold and silver extraction because a treatise, de la Pyrotechnica, published in 1540 in Venice, asserted that silver could be obtained from its ores by a wet salt process. In 1609 a priest, Alonzo Barba, invented a process using a copper vessel and boiling a solution of salt to extract silver chloride ores. The copper vessel was, of course, one of the reactants. This led to the Kronke process introduced in Chile in 1860 which substituted cuprous chloride for the kettle. A major step was taken in Europe in the late 1700's to chloridize roasted silver ores in combination with amalgamation using iron to reduce the silver chloride. By 1843 the Augustan process was introduced. Ores were roasted with salt and leached with a saturated salt solution. The silver chlorides passed into solution from which silver was precipitated by copper. In 1848 sodium or calcium thiosulfate solution of silver chloride was suggested by Dr. John Percy, and the idea was applied in 1856 by Von Patera in Bohemia.

Jan 1, 1983

By I. Iwasaki, P. L. De Bruyn

Electrical double-layer properties of the silver sulfide-solution interface in different electrolytes and the influence the properties exert on the adsorption of dodecylammonium acetate (DAA) were studied using an electrochemical titration technique. The flotation behavior of silver sulfide was observed using DAA as collector and the results were correlated with adsorption measurements. Silver and sulfide ions were identified as the potential determining ions and their adsorption densities were measured as functions of the pAg and of the ionic strength at two different pH values. The point-of-zero-charge (PZC) was observed to be at pAg 10.2, the value being independent of pH and of the nature and concentration of the electrolyte used. The surface charge of silver sulfide in these electrolytes was positive for pAg values less than 10.2 and was negative for pAg values greater than 10.2. The adsorption of amine on silver sulfide surfaces at pH 4.7 was found to be strongly dependent on the pAg. A shift in the PZC towards a lower pAg due to the adsorption of amine indicated a specific affinity of dodecylammonium ion towards silver sulfide surfaces. At pH 9.2 a strong adsorption of the undissociated amine molecule was indicated. The PZC shift towards a higher pAg and the adsorption of the amine was virtually independent of the interfacial electrical conditions.

Jan 1, 1972

By Cyril Stanley Smith, Earl W. Palmer

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization. MATERIAL USED After some preliminary heats had been made in the laboratory to determine the effect of copper, several castings from commercial air-furnace heats were obtained, and data from these alone are given here. Part of the metal was poured directly and part was treated in the ladle with the desired amount of copper before pouring. Green-sand molds were used, each holding two tensile test pieces of the form adopted by the Malleable Iron Research Institute, or two bars for graphitization studies, 5/8 in. in diameter and 9 in. long, fed through two enlarged sections equidistant from the middle and ends of the bars. Risers of suitable size insured sound castings. Tensile tests were made

Jan 1, 1935

Crushed limestone is now being "de-dusted" at the Warner Co. plant in Bellefonte, Pa., by a new high-efficiency classifier utilizing aerodynamic principles not previously employed in classifiers. Crushed limestone for certain glass industry requirements must not have more than 10 pct fines in the overall aggregate, and it is the function of the new-type classifier to separate these fines from the coarse material. During the development of this classifier by the Buell Engineering Co. of New York, it was found to have possible applications for separating pulverized coal, sintered metals, ores, mineral flours, and fillers, among other items. Limestone from Warner's deep mine is initially crushed and particles larger than 3/8-in. mesh are burned in kilns to provide calcium oxide for the chemical industry. The 3/8-in. screenings are dried and crushed to -16 mesh for use by the glass industry. For those applications requiring a minimum of fines, no more than 10 pct -100 mesh material is allowable in the end product. Hence the need for high-efficiency separation.

Jan 11, 1960

By M. H. Merriss

Some years ago, at the plant of the Baltimore Copper Smelting & Rolling Co., the receipt of large quantities of copper blister running high in lead, nickel, and arsenic resulted in the formation of a great amount of very foul slag, in the anode furnaces. A typical analysis of this slag was: Gold, oz. per ton......... 0.09 Arsenic, per cent.......... 0.60 Silver, oz. per ton......'.. 13.20 Antimony, per cent........ 0.50 Copper, per cent......... 19.50 Silica, per cent............ 28.30 Lead, per cent........... 11.90 FeO, per cent............. 19.20 Nickel, per cent.......... 4.60 CaO, per cent............. 1.60 The problem was to get out the copper in marketable form, to save the gold, silver, and particularly the nickel, and to get rid of as much as possible of the lead, arsenic, and other elements that were valueless to the Baltimore plant. In a copper refinery that does not take custom material for matte smelting, the usual method is to smelt the anode slag with coke in a reducing furnace, the black copper thus formed being sent back to the anode furnaces; this was the custom at Baltimore. An average anode slag will contain, perhaps, 40 per cent. copper and such small quantities of lead, nickel, etc., that smelting will get rid of most of these impurities in the black-copper furnace slag. To treat such an impure slag in this way, however, would result in a large nickel loss, and would send back to the anode furnaces all the lead and nickel not so lost, where it would be slagged off again and returned to the black-copper furnace as a slag still more concentrated in impurities. The result would probably be a constantly increasing amount of anode slag containing a likewise constantly increasing percentage of impurities. To avoid such a disastrous closed circuit some other process had to be devised. A small multiple-tank room, built for impure copper as an adjunct to the main series electrolytic refinery, was available, so the following standard process was suggested:

Jan 1, 1924