Search Documents

By D. W. Fuerstenau

THE object of this article is to point out the experimental relationship which exists among contact angle, adsorption density, zeta potential, and flotation rate data. In each of the experiments discussed in this article, the surface properties of quartz, as a function of pH, were measured in solutions to which constant quantities of dodecylammonium acetate were added. Morrow1 and deBruyn2 worked with solutions containing 4.08x10-5 moles per liter, whereas Fuerstenau3 and Seele worked with solutions containing exactly 4x10 moles per liter, but this difference is not significant. The pH of the solutions was regulated with HCI or NaOH in all cases. In each case, the addition of collector was constant, but the concentration of dodecylammonium ions decreased because of the formation of dodecylamine at higher pH values2 Contact Angles: Gaudin and Morrow1 presented data for the contact angle of quartz in solutions containing 4.08x10-5 moles of dodecylammonium acetate per liter between pH 2 and pH 10.15. Using the same captive bubble techniques, the writer measured contact angles on quartz in solutions containing 4x10-5 moles of dodecylammonium acetate per liter at pH values ranging from 9.9 to 13.2. Both sets of data are presented in Fig. 1, in which the contact angle in degrees is plotted as a function of the pH of the solution. From pH 2 to about 8, the contact angle increases slightly with increased pH, but further increase in pH causes a sharp rise in the contact angle to a maximum of about 80º. At pH values above 11.6, the contact angle drops sharply, reaching zero by pH 12.6.

Jan 12, 1957

By O. J. C. Runnals

The intermetallic compounds NpAl2, NpAl3, and NpAl have been prepared, and examined by X-ray diffraction methods. The compounds are isostructural with the corresponding U-Al compounds. NpAl3 is face-centered cubic with a = 7.785A and has the MgCu2 structure. NpAl is simple cubic with a = 4.2624 and has the AuCU3 structure. NpAl4 is body-centered orthorhombic with a = 4.428, b = 6.268, and c = 13.71A. The published description for the atomic positions in UAl, applies also to NpAl4 THE U-Al system has been examined by Gordon and Kaufmann.1 They identified the following intermetallic compounds: UAI2, UAl3, and a third, tentatively identified as UAl5. A structure analysis of the latter compound by Borie2 proved that the formula UAl4 was more consistent with the X-ray data. The crystal structures of UAl2 and UA have been reported by Rundle and Wilson.3 UAl2 was found to be isostructural with MgCu. The atomic positions in the simple cubic UA1, cell were found similar to those in the AuCu3 structure. Three analogous compounds exist in the binary system Np-Al. X-ray data for the compounds NpAl2, NpAl3, and NpAl4 are reported below. The neptunium used in the investigation was supplied through the courtesy of the Argonne National Laboratory as neptunium (V) nitrate. It was stated to have a radioactive content of 99.25 pct Np237. The impurity limits had been established by a spectrographic analysis given in Table I. Any titanium, boron, or bismuth impurity should be effectively removed during the fluorination of NpO2 to NpF4, and sodium, lithium, magnesium or strontium during the alloying procedure. The oxalate ignition technique, described by Westrum for the preparation of finely-divided reactive PuO2, was used.The neptunium (V) nitrate solution, containing 100 mg Np, was evaporated to dryness on oxalic acid crystals. The resulting oxalate was calcined to NpO, by heating in platinum at 650°C for 2 hr. An equimolar mixture of anhydrous hydrogen fluoride and purified hydrogen was passed over the NpO2 for 2 hr at 500°C. According to Fried and Davidson" the above fluorination conditions should produce the purple-black fluoride, NpF3 However, the light-green product showed only NpF4 lines on an X-ray diffraction pattern and contained only an estimated 5 pct of finely dispersed black NpF3 particles on microscopic examination. NpAl3: An intimate mixture of 50 mg of neptunium fluoride and aluminum powder (99.99 pct pure, —28 to $60 mesh) was heated to 900°C in a BeO crucible in vacuum by a tungsten coil for 2 hr, to allow the following reaction to proceed: NPF4 + 7Al + NpAl, + 4AlF. [1] The formation and sublimation of aluminum mono-fluoride in this system was verified from an X-ray diffraction analysis of the sublimate. The diffraction pattern was similar to one obtained in the aluminum reduction of UF4 to UF3,6 showing both Al and AlF3 lines. The resulting alloy was sintered at 1100°C for 1 hr. A powdered specimen of the crystalline product was sealed in a thin-walled quartz capillary for X-ray examination. The photograph was taken on a 14.32 cm General Electric powder diffraction camera, using filtered copper radiation. The films were calibrated in terms of a NaCl standard pattern. The wavelengths used in the calculations were 1.5418A for Cu K and 1.5405A for Cu K The powder diffraction pattern showed that NpAl is simple cubic with a = 4.262 % 0.005A, and is isostructural with UA13 where a = 4.27A1 or a =

Jan 1, 1954

By Robert L. Braun, Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides, chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 100° to 150°C. The rate of dissolution of chalcopyrite exposed to oxygen-saturated solutions becomes so rapid under these conditions that the rate of copper extraction becomes limited by the accessibility of chalcopyrite to the solutions. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, and size of ore particles. It is concluded that the high pressure and high temperature obtainable in a large ore mass broken by nuclear explosives promise the rapid and economic recovery of minerals not considered soluble by conventional in-situ leaching methods. The method should be broadly applicable to the kinds of deep deposits that must be depended on for future production and with minimum disruption of the environment.

Jan 1, 1974

By C. C. Hatch, C. R. Larsen, A. L. Mular

INTRODUCTION As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer/winter of 1975 and during the summer of 1978 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses, to permit study of alternative circuit configurations if desired and to perform off-line optimization. This chapter describes the methodology employed to develop the simulator (1,2) along with typical applications thereof. SECONDARY CRUSHING PLANT FLOWSHEET Figure 1 is a schematic diagram of the Brenda Mines Ltd. secondary crushing plant circuit. The 41,000 tonne coarse ore stockpile(a) is -17.8 cm oversize (3B belt) from two 2.4 m x 6.1 m double deck vibrating screens (not shown). The screens are fed by 2 conveyor belts operated in series with two 198 cm apron feeders that handle discharge from a 152 cm x 226 cm primary gyratory crusher(520 KW). The primary crusher (not shown) treats up to 2725 tonne/hr of run of mine ore. Minus 1.9 cm undersize from the primary screens (#19 belt), referred to as the primary fines, joins secondary screen undersize (#18 belt) for conveyance to fine ore bins (not shown). Feed from the coarse ore stockpile is transferred by means of vibrating feeders and two 120 cm conveyors (#6 and #7) to transfer belts #8 and #9 (Figure 1). The belts feed two secondary 2.1 m standard heavy duty cone crushers (bl and b2). Each crusher is equipped with a modified coarse mantle liner and a standard coarse bowl liner. Mantle throw is 9.2 cm; nominal close side set is 3.2 cm. Crusher .countershafts (443 rpm) are driven by single 260 KW synchronous motors (710 rpm). Discharge from the secondary cone crushers joins discharge from four 2.1 m tertiary heavy duty shorthead cone crushers (fl, f2, f3 and f4). With the exception of the cavity (modified medium mantle liner and standard coarse bowl liner; close side set is nominal .84 cm) and motor (224 KW), these machines are similar to the secondary crushers. The combined discharge is transferred from a 183 cm conveyor to #14 belt which empties into a 1452 tonne secondary screen surge bin (c). Vibrating feeders beneath the bins feed five 2.4 m x 6.1 m double deck vibrating screens (dl, d2, d3, d4 and d5) sloped at 200 from the horizontal. The upper decks are punched plates with 2.7 cm x 7.6 cm slots. Lower decks are woven wire (1.27 cm diameter) sections with

Jan 1, 1982

By SME

A regular feature of the December issue is the abstracts of graduate theses in the mineral industry field presented during the preceding year. The following abstracts were submitted for this second article in the series.

Jan 1, 1976

By Om P. Garg

During the period between 1970 and 1974 the Iron Ore Company of Canada had embarked on a detailed program to evaluate all aspects of mine design work for its open pit mines around Schefferville, located both in Quebec and Labrador, Newfoundland, Canada. One of the main conclusions was that the majority of the slope angles for the ultimate pit walls could be steeped. During the period 1975 and 1976,five (5) open pit iron ore mines were redesigned using the steeper slope angles up to 55 degrees. Initially these pits were designed at slope angles varying between 37 degrees and 45 degrees due to the generally fractured and leached nature of rocks in the area. During the active mining phase between 1976 and 1979, the stability of the steeper ultimate pit walls was monitored. The mining of ore was successfully completed in 1978 and 1979 in three pits. This of course, resulted in a significant savings due to a reduction in the quantity of waste that had to be removed. The successful pit slope redesign project was a co-operative effort between the Federal Government, Universities and the Iron Ore Company of Canada.

Jan 1, 1983

[ ]

Jan 1, 1938

By S. F. Ramseyer, E. A. Steigerwald

INFILTRATED structures represent composite materials which are capable of combining high-temperature strength with adequate low-temperature toughness and thermal shock resistance. Although copper- and silver-infiltrated tungsten structures are actually being used in rocket nozzle hardware, adequate understanding of the fracture mechanics of these composite systems is not available. Specifically the relative importance of the strength, ductility, and modulus of the infiltrant in determining composite properties is not known to the extent that optimum composites can be selected. The major portion of experimental effort in the area of composite strength has been devoted to fiber-reinforced systems1 or to systems where a discontinuous phase is imbedded in a relatively ductile matrix.2'3 In the case of high-temperature systems, which are composed of a relatively brittle matrix, such as tungsten or an oxide, a continuous phase exists for the propagation of a crack. The method by which the presence of a conjugate ductile continuous phase influences the gross properties of the composite represents an area which requires further investigation. This technical note presents results which evaluate the effect of infiltrant strength on the strength of the tungsten-base composite. A tungsten matrix and copper-base infiltrant were selected for the initial studies because of the ease of fabrication. Tungsten structures with nominally 20 and 30 pct porosity were evaluated. The porosity was controlled by varying the initial powder size and a ratio of open-to-total porosity greater than 95 pct was obtained by selective sintering cycles. The processing sequence involved hydrostatic pressing followed by a 72-hr presinter in hydrogen at 2000° F and a final sinter at 4000°F for 4 hr in vacuum. The 20 pct porous structure was obtained

Jan 1, 1965

By J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and ferric iron concentration. The results have been discussed in terms of the adsorption of ferric cations and ferric hydroxide to the quartz surface. Possible relationships between the experimental results and the flotation of quartz have been examined. The adsorption of multivalent cations at the surface of quartz has been studied by many investigators who have used a variety of experimental techniques ranging from streaming potential 1 to radiometric2 measurements. Two possible mechanisms of cation activation of quartz have emerged from the results of these investigations viz: the adsorption of the cation to the negatively charged quartz surface, followed by adsorption of the collector anion to the adsorbed cation site, or: formation of a cation-collector complex which is then adsorbed to the quartz surface. In many natural and industrial systems one of the most prevalent activating species for quartz is ferric iron, this is especially so in the acid-circuit, anionic flotation of iron ore. The adsorption of ferric iron to the quartz surface is complicated by the ability of ferric iron to form complexes with anions, a phenomena which is of minor importance in one of the most widely studied quartz activation processes, ca ++ activation.* *The pK value for [ca(oH)+]/ [ca2+] [oh-] is 1.46 indicating that the influence of Ca (OH)+ ions will be minor in all but strongly alkaline solutions. In order to obtain a better understanding of quartz activation by ferric iron the zeta potential of quartz in the presence of ferric iron has been measured over a range of pH and ferric iron concentration. EXPERIMENTAL METHODS Materials: Selected samples of "rock clystal" quartz from New England, N.S.W., were ground in a pebble mill, washed for three hours in boiling concentrated hydrochloric acid, washed in hot chromic acid and then washed repeatedly with distilled water until the washing water gave no trace of chloride ion.

Jan 1, 1967

By J. R. Long, E. T. Hayes, D. C. Root, R. S. Dean

The U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities1 and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriatc applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately- applicable. While atomic: hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-are methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1947

By J. R. Long, R. S. Dean, D. C. Root, E. T. Hayes

The U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities1 and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriatc applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately- applicable. While atomic: hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-are methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1947

By Dan White

Stress measurements taken at Climax, El Teniente, Henderson, Lakeshore and Urad mines indicate that the deposits cited are generally subject to an inclined stress field that can be highly anisotropic. The horizontal stresses vary significantly between deposits and exceed the measured vertical stresses at Henderson and El Teniente mines. Experience at Henderson, Lakeshore and Urad mines is used to suggest a relationship between cavability and the premining stress. In poorly fractured, high strength rock masses, high stresses can assist the caving process. In well fractured, low strength rock masses, caving is ensured by breakage along fracture planes. The relationship between ground weight and the premining stress is also investigated. Ground weight problems appear to be most related to the competence of the ground rather than the magnitude of the premining stress as supported by experience at Climax and El Teniente mines. Recent developments in block caving favor the extraction of poorly fractured, high stressed rock. Accompanying the development of these deposits are new problems such as rock bursts. These pose particular problems to mine designers in that no experience currently exists in combatting rock burst problems at block caving mines.

Jan 1, 1984

By Norman Ketzlach

ANGANESE today overshadows all strategic materials in our planning for national se-curity," according to a report issued recently by the American Manganese Producers Association. By far the greater part of the manganese ore used in the United States is imported. "We have enough manganese ore in the United States to last from one hundred to three hundred years and longer, but most of the deposits are undeveloped. As in the case of copper, lead, and zinc, manganese ore, both foreign and domestic are low grade. Manganese ores have to be concentrated and processed. After being processed, domestic ores are higher grade than foreign." Most of the manganese ore found in this country, however, is not amenable to concentration by ore-dressing methods. Manganese Products, Inc. has developed a sulphurous-sulphuric acid leaching process for the recovery of manganese from low-grade, intermediate manganese ores. By the term "intermediate manganese ores" is meant those ores in which the manganese in the form of manganese oxides is found to have two different valences, usually two and four, as is probable in Mn,O, or the ore may be a mixture of manganous and manganic oxides. "Intermediate" manganese siliceous ores are ores in which the silica is a constituent of the ore and is loosely linked to the manganese by water of crystallization. This process has been carried out with the type of manganese ore found in the Olympic Peninsula of western Washington; Clough, N. C.; and Lava Hot Springs, Idaho, as well as just recently with manganese ore from Las Vegas, Nev. As far as the manganese leaching process is concerned, these ores differ primarily in the form in which the manganese oxides occur. The tetravalent manganese, the manganese existing in the dioxide form, is soluble in a sulphurous acid solution. To dissolve the divalent manganese, sulphuric acid is required. To dissolve the type of ore found in Washington and North Carolina, a mixture of both sulphurous and sulphuric acid is used. Whereas to dissolve the type of manganese ore found in Idaho and also in Montana, sulphurous acid alone is sufficient. The Nevada manganese ore is of the same type as that found in Idaho as far as the leaching process is concerned. It has long been known that manganese ores, with the exception of rhodonite, which is a true manganese silicate ore, can be dissolved readily in sulphurous and sulphuric acids.' The removal of the impurities such as silica, iron, and alumina from the resulting solution is the step that has been difficult. The process worked out by Manganese Products has been carried through pilot-plant equipment. This process has also been extended to the production of ammonium sulphate. Leaching of Ore: The manganese ore, ground to —-65 mesh is leached with sulphurous acid and sul-

Jan 1, 1951

By Norman Ketzlach

ANGANESE today overshadows all strategic materials in our planning for national se-curity," according to a report issued recently by the American Manganese Producers Association. By far the greater part of the manganese ore used in the United States is imported. "We have enough manganese ore in the United States to last from one hundred to three hundred years and longer, but most of the deposits are undeveloped. As in the case of copper, lead, and zinc, manganese ore, both foreign and domestic are low grade. Manganese ores have to be concentrated and processed. After being processed, domestic ores are higher grade than foreign." Most of the manganese ore found in this country, however, is not amenable to concentration by ore-dressing methods. Manganese Products, Inc. has developed a sulphurous-sulphuric acid leaching process for the recovery of manganese from low-grade, intermediate manganese ores. By the term "intermediate manganese ores" is meant those ores in which the manganese in the form of manganese oxides is found to have two different valences, usually two and four, as is probable in Mn,O, or the ore may be a mixture of manganous and manganic oxides. "Intermediate" manganese siliceous ores are ores in which the silica is a constituent of the ore and is loosely linked to the manganese by water of crystallization. This process has been carried out with the type of manganese ore found in the Olympic Peninsula of western Washington; Clough, N. C.; and Lava Hot Springs, Idaho, as well as just recently with manganese ore from Las Vegas, Nev. As far as the manganese leaching process is concerned, these ores differ primarily in the form in which the manganese oxides occur. The tetravalent manganese, the manganese existing in the dioxide form, is soluble in a sulphurous acid solution. To dissolve the divalent manganese, sulphuric acid is required. To dissolve the type of ore found in Washington and North Carolina, a mixture of both sulphurous and sulphuric acid is used. Whereas to dissolve the type of manganese ore found in Idaho and also in Montana, sulphurous acid alone is sufficient. The Nevada manganese ore is of the same type as that found in Idaho as far as the leaching process is concerned. It has long been known that manganese ores, with the exception of rhodonite, which is a true manganese silicate ore, can be dissolved readily in sulphurous and sulphuric acids.' The removal of the impurities such as silica, iron, and alumina from the resulting solution is the step that has been difficult. The process worked out by Manganese Products has been carried through pilot-plant equipment. This process has also been extended to the production of ammonium sulphate. Leaching of Ore: The manganese ore, ground to —-65 mesh is leached with sulphurous acid and sul-

Jan 1, 1951

THE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given composition and quality. In comparison with other steel-making methods, the basic open-hearth process is one of the most versatile, both from the stand- point of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. In the case of some types of liquid-metal charges the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF THE BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO). This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SO2), manganese oxide (MnO), iron oxides (FeO and Fe203), and phosphorus oxide (P205) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course of the

Jan 1, 1944

[ ] [LOCAL SECTION CODE (Numbers indicate Sections) No. Section LI Alaska L50 Adirondack L2 Arizona L58 Arkansas L84 Balcones L66 Billings Petr. L3 Black Hills L4 Boston L76 Caracas L5 Carlsbad Potash L6 Central Appal. L60 Central N. Mex. L7 Chicago L79 CIM-AIME Calgary L82 CIM-AIME Edmonton L8 Cleveland L9 Colorado]

Jan 1, 1961

By Forrest W. Kinsey

The use of pellets in North American blast furnaces has made the mixes used in the associated sinter plants unique. These mixes generally contain a high percentage of fine waste oxide materials as the principal iron bearing portion of the mix, with iron ores and concentrates added in minor amounts only. Additionally, the sinter basicity is always above one and can be three or higher. This paper will discuss the large body of knowledge and experience developed by one company on this type of sinter mix. Results of laboratory tests will be used to illustrate how mix composition and feed preparation affect sinter productivity and quality.

Jan 1, 1977

By George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95,955 mt (105,770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/mt (0.36 oz/st) silver with 0.94 % copper, 1.10 % lead and 11.06 % zinc. Ore reserves at El Roble are estimated as 1.1 Mmt (1.21 million st) grading 4.89 % copper and 3.39 g/mt (0.099 oz/st) gold. Geologically possible reserves at Equis may total 1.6 Mmt (1.76 million st). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1985

By Francis Clark

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200° C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating. EXPERIMENTAL WORK The object of the experimental work was to study the effect of mechanical work on rolled 60:40 brass, quenched and reheated, and the mechanism of twinning in the alpha reeds of a furnace-cooled specimen. It was desired to determine the effect of mechanical work on the transformations taking place on reheating the quenched material, both at 200 and at 470° C. A study of the nature of the structure resulting from the breakdown of the beta at 200° C. and a study of the mechanism of twinning above 470° C. were considered problems for investigation. The question of the twinning of the alpha reeds was also an important phase of the work. With high-power magnifications, there was hope of following these processes.

Jan 1, 1927

By V. F. Parry, S. P. Burke

The presence of gas in coal mines necessitates the use of costly ventilation arrangements and the use of expensive mining methods. On the other hand, the gas itself in many instances is of considerable intrinsic value, and its separate recovery might conceivably be a profitable undertaking. This paper is concerned with a study of the movement of gas in coal strata with the object of determining the laws governing gas movement and thus making at least a preliminary step toward the solution of the more practical problem of its control or recovery. Naturally, so important a subject has received much attention from scientists and engineers. In most cases, however, the studies have been concerned with the origin1$, the amount" the composition3 and the method of retention4 of the gas in coal; or, from the more practical side, have been concerned with the phenonlena and conditions associated with outbursts5 or explosions and their control. Numerous studies also have been made of the permeability of coal to gas" of gas pressures measured in coal seams, etc. The authors are unaware, however, of any attempt to present a consistent or complete picture of the laws governing the movement of gas through the coal. Study in West Virginia A recent study conducted at this University7 gives the first presentation of the distribution of pressures in a small section of a coal seam. Holes were drilled into the coal rib to various depths and at various distances from the coal face. The location selected for study was as remote as possible from disturbing influences of mining operations, faults, "wants," etc. The pipes extending into the coal that were used to determine pressures were grouted into the borehole for the entire depth of the hole, and great precaution was taken to insure accurate pressure readings. A map of the geology of the region, a map of the probable boundary and extent of the coal seam, a current map of the mine and a

Jan 1, 1936