Search Documents

By Albert G. Zima

ACCORDING to recently published statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed.. Today, 'however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. DRILL TOOLS Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brinell hardness

Jan 1, 1935

By John W. Pack

AT present the manufacture of metallic zinc, or spelter, in Missouri, is carried on only at the establishments located at Carondelet, or South St. Louis. Although the development of the industry has not yet reached that fulness which it has attained elsewhere in the United States, still the commanding advantages of position of these establishments are so evident that the prospective importance and magnitude of spelter manufacture in this State, and especially at this locality, can hardly be doubted. A study of the chemical and technical aspects of the business of these points cannot be without interest to the metallurgist as well as to the capitalist. I have endeavored to investigate, as far as was practicable, within the limits of a paper of this character, some of the problems connected with this industry, at the same time making a few comparisons of the results attained at some of the Carondelet works with those of other establishments with regard to which information could be obtained. In the prosecution of these studies I have been kindly aided by the managers of Carondelet establishments, and by Prof. Charles P. Williams, Director of Rolla School of Mines. To the latter I am especially indebted for assistance in regard to methods of analysis. To all these gentlemen I return my thanks for their valuable aid. Other sources of information will be duly credited in their proper places.

Jan 1, 1875

By S. W. Miller

DURING the examination of welds made in steel by the oxy-acetylene and electric-arc processes, the writer has met with some unusual structures, which he has not encountered elsewhere. They seem to be quite closely associated with the welding methods used, and characteristic of them, and would seem to be worth noting, especially as the references to them in the literature are few, and their explanation not clear or complete. An introductory word or two about fusion welding may not he out of place. The oxy-acetylene process is based on the great and very local heat generated by the burning of acetylene in the presence of commercially pure oxygen, the two gases being thoroughly mixed before combustion. The theoretical temperature is somewhat under 4000° C., but on account of various losses, the actual maximum temperature is probably about 3000° C. 1 The electric-arc process, using a metal electrode, which is also the filling rod, generates a still higher and more local temperature. The actual temperature of the positive crater of the carbon arc is given as 3500° C.2 No figures have been found for the temperature of the arc using a metal electrode, but it would probably not be very different from that of the carbon arc, and probably higher than that of the oxy-acetylene flame. The greater localization of the electric arc is due to the fact that it is not surrounded by a large envelope flame as well as to its higher temperature; while the oxy-acetylene white cone, or welding flame, in which the carbon of the acetylene is burned to CO, is surrounded and preceded by -a long envelope flame, itself of quite high temperature, in which the CO is burned to C02, and the hydrogen of the acetylene to

Jan 2, 1918

By F. S. McNicholas, M. S. Walker, V. C. Rogers

During the year of 1944 and the first half of 1945, the Climax Molybdenum Co. made a study of some of the problems in block and panel caving, with the use of a scale model. The experiments dealt essentially with the type of rock and conditions at Climax, but some experiments were carried out to simulate conditions found in other mines. Most of the previous experiments on the caving characteristics of rock have dealt with sedimentary or broken igneous material. The series of experiments described here was designed to show the caving action of unbroken igneous rock. Con- siderable difficulty was experienced in duplicating unbroken material in the model. The results obtained are believed to be relatively correct, but verification must necessarily come from future mine operation. Observations in the mine and glory hole, together with statistical data, were used as criteria for creating similar conditions in the model. In 1913, George R. Lehman' experimented with broken material in a model for the Inspiration Consolidated Copper Co. and, more recently, P. B. Bucky2 experimented with broken material with a capping of mill tailings. Mr. Lehman's model represented a maximum ore height of 70 ft. capped by 55 ft. of waste. He varied the draw-hole spacing from 6¼ ft. to 8? ft. and 12½ ft. The material used graduated from fines to 30-in. maximum size. Some of his conclusions were: "(I) The less the distance between chute centers, the greater the extraction (Fig. I); (2) the higher the ore column, the greater the extraction; (3) the less the amount drawn at a time from each chute, uniformly, the greater the extraction of clean ore before the capping appeared, but not the greater the total extraction to a I per cent copper final product." (Fig. 2.) Professor Bucky concluded, in part: "(I) Drawing of ore may take place at any time from any finger and in any amount without affecting materially: (a)

Jan 1, 1946

By S. E. Piper, E. M. Buchalter, R. P. King, E. T. Woodburn

The problems involved in an optimum decision making model for flotation circuit are, first of all, to characterize the feed material in terms of parameters which can quantitatively describe the network flotation action in terms of a feasible set of control actions. Once the characterization has been postulated, it is then necessary to devise tests relating to parameter sensitivity, in order that credibility of the model predictions can be assessed. Once a credible model is available, the optimum control set is determined by a hill climbing technique. Details will be reported as to the credibility of model predictions using the stochastic flotation model on a network and further, computational problems associated with hill climbing for a complex objective function are reviewed. Discussion is presented on use of the Rosenbrock technique with constraints and use of a modified objective function with constrained derivatives when employing Fletcher and Powell technique.

Jan 1, 1969

By W. I. Duvall

A brief review of the resonant frequency and ultrasonic pulse methods for obtaining elastic constants of rock samples shows that the equations for an iso-tropic elastic solid commonly used to calculate Young's modulus, modulus of rigidity and Poisson's ratio can result in appreciable error if the rock is even slightly anisotropic. Consideration of the equations that relate bar velocities and free medium velocities to elastic constants for orthotropic, transversely isotropic and isotropic solids shows that a combination of the two methods can be used to determine average elastic constants for a single sample of rock. The determination of elastic constants in different directions requires a large number of tests on oriented samples. The use of both the resonant frequency and ultrasonic pulse methods is recommended so that the determination of both Young's modulus and modulus of rigidity is independent of the determination of Poisson's ratio. The dynamic elastic constants of rock can be determined in the laboratory from measurements on small samples which may be in the form of right circular cylinders (diamond drill core). Either the resonant frequency6 or ultrasonic pulse method1 can be used to determine the longitudinal and shear velocities in the same specimen. The resonant frequency method provides a measure of the longitudinal bar velocity, V,, and the torsional bar velocity Vt; whereas the ultrasonic pulse method provides a measure of the free medium longitudinal velocity, Vp, and the free medium shear velocity, V, . The elastic constants (Young's modulus E, modulus of rigidity G, and Poisson's ratio v) are calculated from the density of the specimen, p, and one of the pairs of velocities by means of equations from isotropic elastic theory. For the resonant frequency method the equations are: It should be noted that Eq. 5 is derived from Eq. 4 and 6 and the relation between the elastic constants for an isotropic solid as given by the first part of Eq. 3. The in situ determination of dynamic elastic constants is accomplished by generating a complex seismic pulse in the rock and measuring the arrival times for the longitudinal and shear phases of the pulse at two distant points.5 From these travel times and the distance of the travel path both Vp and Vs are determined. The density of the rock is determined from samples in the laboratory, and Eq. 4 to 6 are used to calculate the elastic constants. These three methods involve the assumption of isotropy and perfect elasticity, and require the use of the relation v = (E/2G) - 1, which holds only if the elastic constants are the same in at least two directions. The calculation of v by means of Eq. 3 introduces considerable error, as a 1% error in V, and V, results in a 20% error in v. If frequencies for samples with a length-to-diameter ratio greater than four and a length greater than 8 in. are measured carefully, the experimental error can be kept to 1%. However, it is not unreasonable to expect that the variation in Vb and Vt with direction may exceed 1%. Thus, for even a small percentage of anisotropy the use of Eq. 3 can result in considerable error in v. The calculation of v by Eq. 5 also involves some uncertainty as a 1% error in Vs and Vp can result in a 6% error in v. By means of the pulse method both

Jan 1, 1965

By John H. Bassarear

By 1968, Cyprus Pima was milling 34.5 kt /d (38,000 tpd) of copper ore using a conventional flowsheet consisting of three stages of crushing, rod milk and ball, mills. A 13.6 kt /d (15,000 tpd) expansion was put onstream late in 1971 using primary crushing, semiautogenous milk, and ball mills. Identical ore is treated in both concentrators. This paper shows the weight and life of each liner for each crusher and each mill over a four year period from 1974-1977. Media consumption is shown for the same period and a comparison is made between the two reduction methods.

Jan 1, 1983

By B. H. Kear, S. M. Copley

A dynamic theory of precipitation hardening in alloys containing cohevenl, stvess-.free, ordered particles is developed. The yield stvess is predicted from the stress dependence of the plastic strain vale, which is related to a derived dislocation velocity-stress function. The theory is shown to predict the magnilude and temperature dependence of the yield stress of a commercial nickel-base superalloy as well as many details of its slip structure. GLEITER and Hornbogen have developed a theory of the yield stress in alloys hardened by coherent, stress-free ordered ptrticles based on the observation that dislocations (b = a/2 (110)) glide in pairs.' When a dislocation pair shears through an ordered particle, the glide motion of the leading dislocation is impeded since it must create antiphase boundary (APB), whereas the motion of the trailing dislocation is assisted because it annihilates APB produced by the first one. Taking into account the APB energy, the size, and spacing of the particles, G-H predict the observed yielding behavior in Ni/18.8 Cr/6.2 A1 alloys composed of a matrix phase y '(nickel-solid solution) and particles of y' (basically Ni3A1). The G-H theory, as well as all previous theories of hardening by coherent ordered particles, do not include the details of dislocation motion; the present dynamic theory is an attempt to overcome this limitation. In the dynamic theory, the yield stress is predicted from the stress dependence of the plastic strain rate, which is related to a derived dislocation velocity-stress function. This function can be evaluated if the structure of the alloy, the APB energy of the ordered phase, and the characteristic drag or frictional stresses of the matrix and precipitate phases are known. The theory is shown to account for the observed temperature dependence of the yield stress in a commercial nickel-base superalloy. 1) NICKEL-BASE SUPERALLOYS Although their compositions are complex, the nickel-base superalloys have remarkably simple structures. A detailed examination of the commercial superalloy

Jan 1, 1968

By Chase Palmer

INTRODUCTION. WHILE the reducing action of organic matter, of ferrous sulphate, and of hydrogen sulphide has frequently been invoked to account for the deposition of native gold and silver from ore-forming solutions, the high efficiency in this respect of certain of the metallic minerals which form the ore itself has not been sufficiently recognized. If a little finely powdered chalcocite is placed. in a test-tube and 2 or 3 cc. of a dilute solution of gold chloride are poured over it, two or three shakes of the tube suffice to remove all the gold from the solution. The color of the solution changes from yellow to pale green, showing that copper is dissolved simultaneously with the precipitation of metallic gold. If a piece of chalcocite is hung in a dilute aqueous solution of silver sulphate (1 normal), a coating of silver begins immediately to form on the mineral, and within a few moments a beautiful silver tree has developed, similar to that formed when metallic zinc is immersed in a similar solution.

Jan 5, 1913

By E. L. Raymond

The effect of heat treatment on the microstructure and resultant notch-bar rupture life of ZNCONEL alloys X- 750 and 718 was studied. It was found that the primary effect of heat treatment in rendering these alloys notch-ductile is the elimination of any y' denuded zone adjacent to the pain boundaries. The mechanisms by which such a denuded zone can arise and be eliminated by heat treatment are discussed. InCONEL Ni-Cr alloy X-750 and INCONEL Ni-Cr alloy 718 are age-hardenable austenitic materials. Alloy X-750 is used for its corrosion and oxidation resistance and high creep-rupture strength up to 1500°F. Alloy 718 is used most effectively up to 1300°F. One of the most important areas in their development has been establishment of consistently good rupture properties, especially in the presence of a stress concentration, such as imposed by a notch. A desire to improve these properties has led to extensive studies of the effect of heat treatment on the micro structure of these alloys and their performance in stress-rupture tests. In earlier investigations"~ of INCONEL* alloy X-750, *INCONEL i s a Registered Trademark of The International Nickel Co., Inc. grain boundary carbide morphology was linked with stress-rupture properties. If, during heat treatment, the carbide MZSC was precipitated in the grain bound-ary in a cellular form, poor rupture properties re-

Jan 1, 1968

OPEN-HEARTH refractories are not merely an accessory to the furnace. They themselves ore the furnace, to all intents and purposes. The steel work of the main structure is merely a frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories with very little supporting structure. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a refractory- protected rod. The liquid is sometimes sent through an additional refractory-lined tun-dish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a non-conducting "hot top." These materials, from ladle to hot top inclusive, are often referred to as the "pouring-pit refractories." CAUSES OF FAILURE Compared with the equipment used in most industrial processes the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. The discussion here of the individual refractory materials will therefore keep uppermost the question "Why, how, and where does it fail?" The principal causes of failure of open-hearth refractories are, in their order of importance: 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spallimg. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. This is by far the most important cause of failure. Liquid iron oxide comes very near to being the

Jan 1, 1944

By G. W. Toop

In a recent publication,31 Darken has derived an equation to describe thermodynamic behavior in ternary metallic solutions with compositions near pure component 1: Eq. [I] is understood to be a general equation, consistent with the ternary Gibbs-Duhem equation, which is proposed as a logical formalism in view of observed behavior in some binary metallic solutions31'32 rich In Eq. and am are constants obtainable from the 1-2 and 1-3 binaries. The parameter 023 may be determined from measurements on the ternary The purpose of this discussion is to compare Eq. [I) or [3] with other ternary formulations involving binary terms, within the regions of validity of Eqs. [I], [2], and [3]. First, the ternary point is considered to be at the intersection of two composition paths, one with constant N1 and another with constant N2/N3 as shown in Fig. 10. The terms in Eq. [3] may be related to the binary points shown by multiplying the first term on the right-hand side of Eq. [3] by N2 (1) /l -N1, the second term by the third term by and the fourth term by each multiplier being unity: It should be noted here that no suggestion has been made that either the binary or the ternary systems form regular solutions. However, Eq. [5] and hence Eq. [3] shows that the contribution made to the ternary excess free energy from the 1-2 and 1-3 binaries has the same form as for a regular ternary system.1 Before considering the term a23 for the above case, a second geometrical relationship is examined with the ternary point at the intersect ion of three composition paths with constant N1/N2, N2/N3, and Nl/N3, respectively, as shown in Fig. 11. For this geometry, ternary values of NZ and N3 in terms of the binary values shown may be substituted into Eq. [I]. Then by making use of identities of the form Eq. [6] contains terms that are similar to those in a ternary regular solution formulation34 based on the geometry shown in Fig. 11. Although at finite concentrations, unless the 1-2 and 1-3 binaries form

Jan 1, 1968

By Rudolph Gahl

RUDOLF GAIL, Miami, Ariz.-Since I wrote the paper on flotation which is in your hands, important developments have taken place, and, for this reason, I will try in a few words to bring it nearer up to date as far as the Inspiration plant is concerned. You, may have noticed that in the Inspiration concentrator, flotation is not solely relied upon for the recovery of the coarser material, but that flotation tailings are split into a sand and a slime product on drag classifiers. The sand product is treated on tables which thus supplement the work of the flotation machines. Extensive tests have shown, us that, if we wanted to, we could leave out these tables and substitute additional flotation machines, as they will make fully as good, if not a better recovery than tables on the deslimed feed, but the treatment would be more expensive, especially in view of the fact that oils are required which cost more than those which we are now using in our main flotation plant. We have, however, decided to apply flotation treatment to our table middlings. I would also like to add a few words regarding the treatment of oxidized copper ores. Although our experience shows that the addition of hydrogen sulphide and other soluble sulphides effects a very good recovery of copper carbonates with certain ores, we have not been able to prove that we could use it advantageously for the ore mixture which we are treating in our concentrator, and for this reason, have looked toward leaching for extracting the carbonate and silicate copper that we are losing now. Experiments in this direction are going on and are giving very encouraging results. It may interest you to hear that we intend to use limestone for the precipitation of the copper which goes into solution, as electrolytic precipitation seems to be out of the question on account of the diluteness of the resulting solutions, and precipitation by iron was rightly objected to on account of the unavoidable contamination of the water supply. We feel very hopeful about the success of our limestone precipitation which, if it holds what it seems to promise, will develop into a novel feature of copper metallurgy.

Jan 10, 1916

By James T. B. Ives

The map exhibited* as an example of my method of construct ing geological strata-maps is essentially an educational appliance. The method, however, is available for the production of maps of comparatively small areas, which, I am confident, will be found of great practical value to mining engineers. Before stating how the method may be so applied I will briefly describe the map exhibited, as the easiest way of making my meaning clear. Almost any region might be taken. This map represents the eastern half of the United States; and the geology is that of the map issued by the Geological Survey, and revised and extended subsequently by Professor Hitchcock for your Institute. I use ten cards, of the colors used in the geological map, each having the geog raphy of the area printed upon it; and I superimpose these in the order in which the colors occur in the index to the map. I next cut away a portion of each card, excepting the lowest, leaving only so much of each as represents the exposure of the formation of that color plus all those which overlie it. When that is done, the whole, looked at from a distance, appears to be an ordinary geological map. Looked at more closely, however, the formations are seen to overlie one another, as in nature. The cards are covered with glass in a frame, which, hinged at the bottom edge, can be let down. The cards are then found to be all hinged in the same manner, and they, too, may be lowered, one after the-other. I am told by teachers of geology of great experience and the highest reputation that by this appliance they will be assisted in im parting to students the first facts and principles of geological sci ence. Having let down the whole series of cards, until that repre senting the Archaean is seen underlying all the rest, the teacher will gradually rebuild it. The Cambrian will thus be laid down upon the Archaean before the eyes of the class, the Silurian upon that,

Jan 1, 1888

By Joseph N. Morrison

A comprehensive solution is offered to the problem of dust emissions at belt conveyor transfer points. Details of enclosure design are discussed and a straightforward procedure for calculating required dust control exhaust volume is presented. Many design variables are taken into account which heretofore have been commonly ignored or inadequately considered. These include belt widths, belt speeds. enclosure openings, material flow rate, material bulk densities, material lump sizes, height of material fall, material temperature, and ambient air temperature. All of these questions are handled by means of a "fill-in-the-blanks" type of calculation form, permitting quick, reliable solutions by relative "non-experts."

Jan 1, 1972

By Fred Bond

WHEN some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material, and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media dur-ing normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many com-mercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an im-portant one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain labora-tory tests were made from which it was found that different materials form coat-ings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qual-ities, like coal and graphite.

Jan 1, 1940

By J. D. Forrester

Many have been prone to credit the decline of professional interest in some branches of mineral industry education to the industrialists and other agencies who use our graduates. We hear the cry that industrial salaries are too low, opportunities for advancement do not exist, and the mineral industry specifically and generally is not interested in the engineer's efforts. Perhaps the time now has come when we should "dress-ranks," examine our practices, and publicize and encourage advanced technical training instead of laying all our troubles elsewhere. There can be no doubt but that industry is interested and stands ready and willing to co-operate. This is demonstrated by the numerous grants-in-aid and co-operative industrial projects which have been made available to those relatively few schools which have been encouraging graduate study and research. There is no dearth of research problems in any of the mineral industry fields and the sooner we realize the great opportunities for constructive, technical research in all areas of our profession the sooner we will reap the benefits of our engineering enterprises by closer liaison and broader understanding with industry. An analysis is offered here of the status of graduate work and research in various phases of mineral industry education in the United States. It is

Jan 1, 1949

By Woolsey McA. Johnson

In metallurgical circles it is known widely, but somewhat vaguely, that the ease of reduction of metallic oxides depends largely on the way they hare been prepared. It is likewise known that different forms of carbon have different and greatly varying reducing powers. It is the purpose of this paper to show somewhat more definitely and scientifically these facts. Some years ago the writer published an account of pyrometric determinations of the reduction temperature of zinc oxides variously prepared and of several kinds.' In said paper it was shown that the temperature at which zinc oxide evolves zinc according to the equa-tion ZnO + C = Zn + CO depends upon the nature of the two reacting bodies. The determina-tions had a range of accuracy of from 2° to 6°C., whereas differences were found to amount to an extreme of 90' C. So the differences are real ones and must have a definite cause. The equation of boiling water, (H2O)4 D 4 (H2O) has a fixed temperature for equilibrium of 100° C. at 760 mm. pressure. In general, all equations reacting in the liquid or the gaseous phase have well-defined constant physical conditions which govern the equilibrium point and reaction velocities. In a reaction where we have one or more solid phases, the tempera ture conditions requisite for the unbalancing of the stable system are found to vary. These variations are due to the fact that in a solid there is a very complex molecule and it is not a question solely of the tearing away of two interlocked atoms, but also of the destruction of a complex molecule containing hundreds, or possibly thousands, of smaller molecules. In other words, there are two forces to be overcome: a certain

Jan 1, 1914

By D. C. Seidel, M. C. Fuerstenau, R. J. Roman

The existence of a surface charge on the alkali halide salts is shown, and a flotation mechanism involving surface charge and collector solubility is developed. Data suggest that KC1 is positively charged and that NaCl is negatively charged in saturated brines, and that the neutral molecule RNH,Cl is the collector in the amine-KC1 system, RSO, is the collector in the sulfonate-KC1 system, and RCOONa) is the collector in the fatty acid-NaCl system. A number of hypotheses have been advanced to explain the mechanism of soluble salt flotation; one of these involves exchange between collector ions and surface cations. With this mechanism Gaudin1 suggested that the differences in flotability of halite and sylvite with primary amines are due to the ionic size of the RNH;, Kt, and Na t ions. Fuerstenau and Fuerstenau expanded this hypothesis to include many other alkali halide salts. Several exceptions to this hypothesis are known. That is, this model does not explain why salts containing the same cation, or why salts of different degrees of hydration, respond differently to flotation. For example, why NaI is floated with an amine whereas NaI .2H,O is not. Further, no correlation between ionic size and flotation response can be made with sulfonate or car-boxylate as collectors. In addition, this hypothesis does not explain the effect of magnesium or lead activation, nor does it offer any explanation of the role of temperature in salt flotation. Rogers and Schulman3 realized some of the inadequacies of the ion exchange mechanism and proposed another mechanism based on the heat of solution of the salts. They concluded that weakly hydrated salts can be floated with alkyl amines and sulfonates, that strongly hydrated salts can be floated with fatty acids, and that excessively hydrated salts cannot be floated at all. Their work was not limited to the al-

Jan 1, 1969

By John V. Beall

Hard as the Revett quartzite are conditions governing the deep mines of the Coeur d'Al6ne. In fourscore years of mining, heat and pressure have been the rewards of preseverance. Such obstacles are the natural concommitant to search for ore at depth. But high cost and shortage of miners is a creeping frustration of the decade. These grim observations were made on a trip to the mines of the Coeur d'Al6ne in the first week of May. But the bouncy optimism of competent mining engineers and geologists overrides by far the tough conditions. This is the story of what they are doing. I think they are setting the stage for the wonder mines of tomorrow. I didn't meet all the people or see all the mines, so there are unfortunate gaps in the story. Then too, sometimes the muck and water blotched my notes, or I couldn't write fast enough or I was too tired. No matter. There is much to tell and, because it is basically a human story, I am flouting the rules of technical journalism and couching it in the neglected "I" person. First then, a little history . . . .

Jan 7, 1966