Search Documents

By Richard W. Markley

A centralized online data acquisition system has been developed by the U.S. Bureau of Mines Pittsburgh Mining and Safety Research Center for rapidly digitizing, storing, and processing experimental signals originating up to 1100 feet away from a central computer. This system, which services seven laboratories, is currently based on a CDC System 17 1/- computer with 56K of semiconductor memory, four disk drives (one shared online with a CDC 1700), two magnetic tape drives, high-speed A/D hardware, and other input/output peripherals. The laboratories are linked to the central computer by 15-pair cables and signal conditioners and to the computer's communications controller by modems and current loops. The A/D throughput rate is approximately 30,000 samples per second (9 bit plus sign resolution) and permits scanning about 30 instruments once every millisecond for up to 100 seconds, being limited only by disk capacity. The laboratories serviced by this facility conduct explosions research and include such facilities as an Experimental Coal Mine Explosion Facility (45 channels), a Constant Volume Combustion Laboratory (4 channels), and a Simulated Coal Mine Laboratory (15 channels). Personnel support includes one systems analyst, two applications analysts, one operator, and a hardware technician. The system has performed adequately for burst-type data acquisition, but due to a lack of long-term reliability (24 hours) of the real-time multiprogramming operating system and unpredictable power failures, slow phenomena signals are generally digitized and stored offline. This latter data is input to the computer through peripherals such as a high-speed paper tape reader, or high-speed asynchronous communications ports. Processing of data is done either in real-time (as soon as data is collected) or in batch mode. Smaller batch jobs are run on this computer, and all others are transmitted by means of the system's high-speed UT 200 terminal simulator to a CDC-6000 series computer.

Jan 1, 1977

By James S. Browning

For the past several years, USBM has conducted laboratory and continuous process development work on the weathered mica pegmatites ores of Alabama, Georgia, and North Carolina to determine the feasibility of recovering commercial-grade mica concentrates by flotation. The research has resulted in the development of two processes for flotation of mica: 1) an acid-cationic method for recovery of coarse mica and 2) an alkaline-anionic-cationic method for recovery of fine mica. The research indicated that the two processes may be effectively utilized separately or in combination for flotation of mica from weathered pegmatite ores. This report summarizes the process development work, and demonstrates the feasibility of producing commercial-grade concentrates with a high recovery of the contained mica. Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama.'" Whereas in western North Carolina, these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites4 To a lesser extent, mica is produced as a byproduct of feldspar" and spodumene. Past research by U.S. Bureau of Mines (USBM) has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica.' This method requires thorough desliming of the ore with consequent fine mica losses. The other utilizes an alkaline-anionic-cationic process for recovering fine-size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica.8-18 The latter process has also been successfully applied to a micaceous schist ore from California.' This report summarizes the results of these research studies. Both of the flotation processes developed by USBM have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores. Description of Ores The weathered mica pegmatite ores used in the investigations were obtained from commercial mica operations in Alabama, Georgia, and North Carolina. The

Jan 1, 1971

By O. B. Buchlen, J. W. Smith

The Coal Research Bureau of the School of Mines at West Virginia University, using an experimental flotation cell designated an airlift-cyclone was able to obtain a clean coal product containing 7.64% ash with 94% yield and 97% coal recovery. This favorable performance was obtained with the experimental flotation cell operating as a simulated three-stage unit on slurry taken from the fine coal circuit of a coal preparation plant. This experimental device, consisting of a sheet metal cyclone-like unit mounted on a U-shaped uplift pipe, uses a combined flotation and cyclone action to beneficiate the minus 14 mesh partially cleaned feed product. In addition to providing comparable analytical results, the airlift-cyclone possesses other attractive features among them being a low capital expenditure, utilization of moderate plant floor space, efficient operation on high density feed slurry, and absence of moving parts. The primary shortcoming of the experimental cell is its limited capacity. The Coal Research Bureau presently has under construction a larger unit which, it is hoped, will provide the capacity and quality to establish the airlift-cyclone as a commercially feasible unit. Froth flotation of fine coal is a practice which has only recently gained wide acceptance in this country. Various explanations can be put forth for this delayed acceptance of a very selective and efficient system of coal preparation. Among these reasons would be the advent of continuous mining machines resulting in the increased production of coal fines, the change in market patterns from domestic and rail consumers who did not want fines to a predominantly utility market which normally consumes fines, and also the imposition of legal restrictions in regard to stream pollution. However, the major detriment is probably the high cost involved both in installation and operation of the flo- tation unit and auxiliary systems. These facts assume greater emphasis when considering that froth flotation installations normally process a low quality feed product. A recent estimate' of installation costs including dryers, filters, and other auxiliary equipment for a flotation system was $5000 to $7000 per ton of capacity while the operating costs, exclusive of auxiliary equipment, were estimated at 10 to 306 per ton of feed. The Coal Research Bureau of the School of Mines at West Virginia University is currently developing a simplified froth flotation cell, designated an airlift-cyclone, which may provide considerable savings in capital and operating costs without sacrificing product quality or recovery. This experimental cell consists of three primary components: 1) a vertically mounted U-shaped pipe; 2) an air injector device; and 3) an integrally mounted cyclone-like unit (Fig. 1). A feed slurry is introduced at the top of one leg of the U-pipe while compressed air is injected near the base of the other leg. The air serves both to aerate the pulp and to cause it to flow upward into the base of the cyclone unit where the floated clean coal is separated from the reject material and unfloated coal which remains in slurry. The Coal Research Bureau's experimental airlift-cyclone is somewhat similar in principle to a flotation device developed by Russian engineers in the late 1950's. In tests upon a two-stage pilot-size device, the Russians obtained very favorable cleaning efficiencies.' However, later experience with production models demonstrated that rated capacities and acceptable product quality could not always be maintained.3 Because of these limitations, Russian engineers subsequently recommended that conventional, mechanical cells be used when cleaning difficult to float slurries. Engineers at the Coal Research Bureau felt that such a device utilizing the combined actions of a cyclone and a froth flotation machine offered numerous attractive features and merited investigation. Accordingly, a small capacity experimental airlift-cyclone was designed and, with the permission of the Christopher Coal Company Div. of Consolidation Coal Co., installed in Christopher's Humphrey preparation plant near Morgantown, West Virginia.

Jan 1, 1964

By R. F. Miller

DUE to wartime secrecy restrictions a large part of the technical information developed by government and industrial laboratories was withheld from distribution. Much of this information has now been released or "declassified" and reports of technical work carried out during the war in allied and enemy countries are also becoming available. Information on the latter subject has been augmented by the work of the Technical Industrial Intelligence Corps of the U. S. Army. Through the Joint Chiefs of Staff, rep¬resentatives of this Corps co-operated with the British Combined Intelligence Observations Subcommittee, and some of the observations were made by combined personnel of both groups. The U. S. Government has undertaken the indexing and abstracting of all of this information in the Bibliography of Scientific and Industrial Reports, a weekly bulletin which appeared first early in 1946. Other publications, such as the Bulletin of the British Iron and Steel Institute and The Metals Review of the American Society for Metals, provide abstracts of domestic and foreign magazine articles and papers presented to technical societies. However, they do not cover the industrial and government reports recently released by the Government nor the reports of the Army investigators hence the new bibliography is a welcome addition to our metallurgical library.

Jan 1, 1947

Jan 1, 1914

By H. W. Hitzrot

SEPARATING a mixture of particle sizes of material suspended in a liquid medium is by no means an exact science. Selecting machines for individual classifying operations is even more difficult. The plant operator's own background is of course invaluable, and considerable help may be obtained from technical articles, talks with sales engineers, and handbooks on ore dressing. These several sources of information, however, are difficult to marshal in proper perspective for the major decision on classification units that an operator may be called upon to make. To the present writer's knowledge this assembly of facts is not available in handbooks, and technical papers are scarce on classification equipment developed in the past five or six years. It is believed that this paper will be helpful to users of classification equipment at this particular period in the development of hydro-classification. For easy reference the following classification units now available and in use in metallurgical and industrial operations are listed below, with a brief description of each. Unit-type classifiers, bowl classifiers, and bowl desiltors are all rectangular tanks, slightly tilted, with reciprocating rakes or screws to remove settled sands. The unit-type classifier, Figs. 1 and 2, is available in widths from 14 in. to 20 ft and lengths up to 40 ft. The shallow bowl of the bowl classifier, Fig. 3, equipped with rotating rakes, is superimposed on the lower end of the tank. Reciprocating rake compartments for this design range from 18 in. to 20 ft wide. Bowl diameters vary from 4 to 28 ft. The flat-bottomed bowl of the desiltor, Fig. 4, of relatively large diameter, is equipped with rakes rotating outward and partly over a pit, which is created by extension of the rectangular tank into and under the bowl section. Bowl desiltors are available with reciprocating rake sections 4 to 20 ft wide and bowls from 20 to 50 ft in diam. The bowl desiltor is used for applications beyond the range of the bowl classifier. The hydroseparator, Figs. 5 and 6, is a circular tank equipped with slowly rotating rake arms, set on a slope, with interrupted rake or spiral blades to move the settled solids to a central discharge cone. Tank diameters vary from 4 to 250 ft. Tank depths at center are 2 to 3 ft for small units and up to 25 ft for larger units. Hydraulic classifiers of the sizer and super-sorter types, Figs. 7 and 8, are narrow, deep, rectangular tanks divided by vertical baffles into a series of pockets. Hydraulic water is added near the bottom of each pocket. Perforated constriction plates, spiral flow arrangements, or jets are used to disseminate the water under pressure (hydraulic water) throughout the bed of material in the pocket. Discharge valves on each pocket are operated automatically by a pneumatic mechanism, a pincer-type mechanism, or a pressure control and motor combination actuated by a hydrostatic tube within the pocket. Hydraulic classifiers are available in 4, 5, 6, and 8-pocket units of varying constriction plate areas to suit conditions. There is now a jet sizer of unit pocket design that can be made up in 1 to 25 sections or more to accommodate sizing requirements. The hydroscillator, Fig. 9, is a rectangular tank set on a slope of 3 to 4 in. per ft. A bowl is superimposed on the lower end. The bowl bottom is an oscillating rubber-covered disk, perforated to allow hydraulic water introduced beneath the disk to set up a teeter bed and thus produce an oversize or rake product exceptionally free of slimes, and material minus the mesh of separation. A shallow dam at the periphery of the bowl allows the coarse or oversize fraction to spill over and drop down into the tank compartment, where it is moved up the deck by reciprocating rakes. The material, minus the mesh of separation, overflows a circular and stationary weir which is several inches higher than the dam on the oscillating disk. It is carried off in a circular launder in the usual manner. These units are available in bowl diameters from 4 to 14 ft and with reciprocating rake compartment widths to suit the tons per hour to be handled. Centrifugal classifiers include the solid bowl centrifuge and the cyclone classifier. The solid bowl centrifuge, Fig. 10, consists of a truncated cone fixed to a horizontal shaft and rotating at high speed. An internal spiral rotating at slightly less speed continuously removes solids deposited on the inner surface of the cone, or bowl. Feed enters the cone by means of the hollow center shaft. Overflow leaves through ports at the large end of the cone, and oversize solids, moved by the spiral, exit through ports at the small end. Centrifugal classifiers of this type are available in cone diameters from 18 to 54 in. The cyclone classifier, Fig. 11, is a stationary cone having a cylindrical upper section and a lower cone section. Feed is introduced tangentially into the upper cylindrical section under pressure from a hydrostatic head or by means of a pump. Centrifugal force thus induced effects a classification within the cone, the fine sizes being carried off in the overflow through an opening at the top of the cylindrical section. Coarse solids at relatively high pulp density exit through a control valve at the apex of the lower cone section. Cyclone classifiers are available in 3, 6, 12, 14, 24, and 30-in. diam. The cone classifier, Fig. 12, is a steel-plate cone with sides usually about 60" from horizontal. It contains no rotating mechanism. Feed enters a feed-well at center and classification is effected by gravity and pulp density. Fines are carried off in the flow over a peripheral weir at the top of the cone. Settled solids exit through an opening at the apex. An apex valve actuated through levers and rods by the pulp density in the lower cone section is usually supplied. Diameters are usually maximum at 8 ft.

Jan 1, 1955

By Michael F. Dunn, Francis S. Kendorski

The fall of rock from strip coal mine highwalls continues to be the largest single source of fatal accidents, so methods to improve highwall stability through improved blasting practices were investigated in the field. This paper covers the results of a project to improve, using existing and proven technology, unstable highwall conditions through better blasting practices in Appalachian strip coal mines. Better borehole blasting agent distribution and optimization of burden, spacing, and delay periods allowing satisfactory breakage with minimal backbreak were the objectives. At a selected field site, geologic conditions were closely examined with regard to joint orientation and spacing, and resulting slope stability considerations. Utilizing surface blasting concepts of trying to achieve flexural failure of the rock mass both horizontally and longitudinally by appropriate relationships between burden, spacing, and hole length, as well as delay time sequence to achieve optimal confinement and breakage, successful results were achieved. A test series of eight blasts was completed and the resultant highwall monitored by repetitive photography. Actual blockfalls could be measured and the stability for each blast design thus quantified. The study of drilling and blasting economics along with equipment performance led to an economic model of blast parameters and the identification of blast design cost benefits. The work demonstrated that small strip mining companies are able to achieve a more stable highwall excavation utilizing presently available technology, equipment, and explosive products at improved operational cost and safety.

Jan 1, 1983

By A. L. Holley

IT has been customary at our opening sessions, for the presiding officer to address you on the general development of one or another of our several professions, or upon some important feature of Mining or Metallurgical Engineering. It is somewhat embarrassing to his successor that our former President, Dr. Raymond, expert as he is in every one of these professions, has been accustomed to keep them all, in their turn, prominently before you. In selecting for this occasion a subject necessarily connected with iron and steel, I have thought that a review of these manufactures, with reference to some of their more pressing needs for improvement, will be more timely than a general or statistical paper. I shall endeavor to confine my remarks to a few specific defects of practice and management, and to their equally specific and more or less developed remedies. That serious defects exist ; that they must be remedied ; that the manufacture is indeed already on the verge of transition, will be generally admitted. But it cannot be revolutionized all at once, however desirable the technical results might be, for that would bankrupt the business at large. We cannot afford to pull down and rebuild all our blast-furnaces that do not make a ton of pig iron with 25 cwt. of fuel ; nor to replace all our hand-puddling furnaces with revolving ones, even if we could select the best revolver. Although the soft steels promise to supplant iron for most structural purposes, there are neither money nor present market to warrant all at once replacing our iron works, or half of them, with steel works. Since, then, these manufactures can neither standstill nor be suddenly metamorphosed, their managers are saying to one another " We must feel our way into larger development ; we must work gradually into better practice; we must improve a little at a time." * President's address on the opening of the Cleveland meeting.

Jan 1, 1876

By Harry R. Cedergren

Properly designed drainage systems can be of great benefit to many kinds of Civil Engineering works, including embankments, and often are the most economical way to protect such works from the damaging effects of water. To function properly, drains must be able to remove water without also removing soil or becoming clogged with soil or erodible rocks. The first criterion to be used in designing drainage systems, called the filter criterion, can prevent all such problems (erosion and clogging) when properly fulfilled in design and construction. The second requirement of drains is that they must be capable of removing all of the incoming water without the build-up of large amounts of head that can damage the protected works. To insure this kind of perfomance, the discharge capabilities of drains should always be verified by appropriate hydraulic and seepage calculations. This paper describes these two basic drain design criteria and also gives examples of application of seepage principles to the evaluation of the potential benefits of drains and to the design of drains for mine waste embankments.

Jan 1, 1985

Jan 1, 1928

By J. E. Dorn, S. K. Mitra

The low -temperature tensile and creep behaviors of single crystals of copper were evaluated and analyzed in such a manner as to provide an estimate of the separate contributions of short-and long-range stress fields to strain-hardening. Furthermore, the average force-displacement diagram for thermally activated intep-section of two dislocations was estublished. This diagram plus a knowledge of the variation of dislocation spacing and the long-range back stresses with strain permits on accurate prediction of creep rates. The calculated activation energy for intersection under conditions of a constant strain rate increases linearly with the absolute tempevatus-e as required by theory. AN understanding of the detailed mechanisms for strain hardening constitutes one of the principal unsolved problems in dislocation theory. Two major models for strain hardening have been advanced in the past. The one that has received greatest attention assumes that strain hardening arises exclusively from long range interaction stresses between moving dislocations and piled-up arrays of blocked dislocations on the slip planes. This type of interaction was first announced by Taylor' who revealed that the back stress fields due to a simple uniform array of positive and negative dislocations entrapped in the deformed crystal would result in parabolic hardening. Shortly thereafter Andrade and Henderson" demonstrated that the strain hardening of fcc single crystals was not parabolic, as previously thought, and finally it was recognized that a typical stress-strain curve consisted of three successive stages of deformation, niz., the easy glide, Stage I, linear hardening, Stage 11, and the parabolic hardening, Stage 111, ranges. The objections to Taylor's somewhat na'ive model, which were presented so forcefully by cottrell; were largely removed by the more realistic details incorporated in Mott's analysis.5 But because Mott's theory for hardening via long range stress fields gave somewhat analogous results to that of Taylor's (inasmuch as it also predicted a parabolic rate of strain hardening whereas the observed rate of strain hardening in Stages I and I1 were linear), it was not widely accepted. Major consideration was therefore given to models, such as those which were advanced by Friedel and seegere that were formulated for the ad hoc purpose of yielding linear rates of strain hardening. The second major thought regarding strain hardening is based on the concept that it arises principally from short-range stress fields due to the interactions between intersecting dislocations. Cottrell and stokes7 showed, several years ago, that the constancy of the flow stress ratio at two temperatures regardless of the strain was inconsistent with the concept that strain hardening arose exclusively from long-range back stresses. The argument that strain hardening was primarily due to local interactions of intersecting dislocations was presented in considerable detail by asinski.' Extending Basinski's method of analysis of the intersection process, Mitra, Os-borne, and dorn recently demonstrated that indeed the strain hardening in aluminum single crystals arises principally from local effects coincident with intersection; however, these conclusions, too, must be modified, as will be shown later in this report. The present investigation, devoted principally to the low-temperature deformation of copper single crystals, was initiated in an attempt to ascertain whether or not the same conclusions arrived at for aluminum also apply to metals, such as copper, which have much wider stacking faults. It was soon observed that the strain hardening in copper could not be attributed exclusively to local effects between intersecting dislocations. Previously no analytical method for arriving at the possible simultaneous contributions of long-range stress fields and localized forces on intersecting dislocations was available; consequently, the separation of these two factors could not be readily accomplished. In the present report a method of estimating the separate contributions of each of these two factors to strain-hardening will be presented. The authors will show that both long-range stress fields of the type contemplated by Seeger and Friedel as well as short-range forces of the type considered by Basinski are responsible for strain hardening in fcc metals at low temperatures. This method of analysis also accounts for, in a satisfactory way, the effect of stress, temperature, and strain on the creep rate under constant stress. Furthermore, in the course of presenting their methods of analysis the authors will also reveal the rather complete agreement of their experimental data with the concepts of the theory for thermally activated intersection of dislocations. INTERSECTION MODEL As shown by seegerl0 the strain rate arising from thermally activated intersection of dislocations is given by

Jan 1, 1962

By J. H. Henderson, T. E. Morrisson

An irvestigation has been made of the production of oil through horizontal fractures of high capacity and large radius placed at the base of producing formations. The specific aitns of the study were to (I) determine by model studies the reservoir performance when gravity drainage is the only producing mechanism, and (2) develop a method of predicting such perfortnance from commonly measured reservoir proper-ties. Although the theoretical approach tailed to develop a rigorous analytic sorution to the transient problem, it (lid lead to a practical method of predicting performance. Predictions (Ire in good agreement with rates and recoveries observed in scaled-model experinzents. Capillary effects and the influence of relative permzenbil-ity are taken into account. The experimental program was mainly concerned with the influenre of fracture radius, fracture capacily and capillary hold-up on the total recovery and the rate of recovery. Much of the experimental work was done on a triangular model which represented one-eighth of a square well pattern, so constritcted that horizontal fractures of varying radii and flow capacity could be studied. An electrolytic model was used to relate the initial production rates to fracture radius, formation thickness and the drainage radius of the well pattern. The conclusions reached as a resrtlt of the work are as follows. I. The production of oil under gravity force alone into a well-propped horizontal fracture, whose radius is of the order of hundreds of feet, is a recovery method which combines high recoveries with very acceptable production rates. 2. The mechanism is effective in "dead oil" reservoirs as well as in reservoirs which possess the energy of solution gas. 3. A method of predicting performance has been developed which gives good agreement with experimental behavior in cases of practicnl interest. Even for very thick beds and large fracture radii, where actual conditions do not conform to the assumptions made, the method gives order of magnitude predictions which would not otherwise be possible. INTRODUCTION Gravity drainage of oil from a formation which has continuous ver- tical permeability over a reasonable depth interval is a surprisingly effective method of recovery. However, for a conventional well the production rates which result from gravity drainage are so low that the economics are seldom attractive. The same formation may produce rapidly and profitably by gravity alone through a high capacity, extensive (i.e., > 100-ft radius) horizontal fracture placed near the bottom of the pay section. Fig. 1 shows a schematic diagram of the plan. Energy in the reservoir gas is not a necessary condition for this recovery process. With a sufficiently large fracture, attractive production rates will result from gravity flow alone, and the producing GOR need only be the solution GOR. It is, of course, necessary to keep the fluid level in

By W. A. Oates, J. A. Lambert, P. T. GaIIagher

Monte Carlo methods have been used to compute the arrangements of interstitial atoms dissolved in tetrahedral sites in bcc lattices. It is assumed that the presence of an interstitial atom "blocks " a certain number of neighboring sites and prevents their occupancy. Sites "blocked" by more than one filled site are allowed for. The computed values of. the mean occupation number (defined as the ratio of the total number of sites blocked to the number of solute atoms are used to calculate the configurational entropies of the solutions. These entropies are compared with those resulting from previous theoretical studies of this problem and also with available experin~ental data for the p Zr-H, Nb-H, V-H, and Ta-H systems. Evidence is also given that the "blocking" explanation of low limiting compositions in these systems, rather than this being due to initial limitations on the number of sites available, is probably correct. THE ideal partial configurational entropy of mixing of an interstitial solute in a metal is given by: where p is the number of interstitial sites per metal atom and Xi is the atomic fraction of the interstitial. For the bcc lattice. which we shall be concerned with in this paper, the interstitial positions are shown in Fig. 1. It can be seen that for the tetrahedral sites, p=6. whereas for the octahedral sites, p = 3. Different emphasis has been placed on the relative importance of energy and entropy effects in determining deviations from ideality in interstitial solid solutions. In some cases the same system, e.g., Fe-C, has been described by the contradictory regular and athermal solution models indicating that the enthalpy and entropy functions, derived from equilibrium data, are frequently not accu.rate enough to differentiate between these treatments. However, for certain metal-hydrogen solutions the equilibrium data is available over sufficiently wide ranges of temperature and composition to permit a reasonably accurate determination of the compositional variation of the heats and entropies. Hoch&apos; has attempted to interpret the results of interstitial solid solutions in terms of a regular solution model. In the case of the Ta-H system where 13 = 6, this model entails fitting the experimental relative partial entropies of solution, asH, to the equation: where ASgs is the relative partial excess entropy of solution of hydrogen. Hoch found that the results of Mallett and Koeh1 could be fitted to this equation with an approximately constant value of AF up to XH = 0.25. However, it is apparent from the solubility isotherms in this system which become asymptotic to the composition TaH that, since (Xh /6 - ~Xh ) becomes infinite only at TaH6, it is necessary that AS<&apos; tends to infinity at TaH. In other words, the low saturation composition of TaH, instead of the anticipated TaH,, eliminates the possibility of applying regular solution theory to such systems. Rather large negative excess configurational entropies must exist at higher hydrogen concentrations in order to explain the lower saturation values. To account for these low limiting compositions and excess entropies two distinctly different approaches have been followed. Rees and many others1-l2 have assumed that not all interstitial sites are crystallographically equivalent with respect to the interstitial addition; that is, in Eq. [I] p is less than the value anticipated from geometrical considerations. To describe, say, a bcc metal-hydrogen system with a limiting composition of MH by this approach one would consider that p = 1 in the first instance instead of p = 6.&apos;j3 In some cases, nonintegral values of B have been taken in order to improve the fit with the experimental data over limited ranges of composition. The other approach which has been used to explain the low saturation compositions is to assume that, although all sites are available for occupancy, strong repulsive interactions exist between the neighboring interstitial atoms, and hence occupancy of any site excludes or blocks a certain number of neighboring sites from being occupied. Earliest treatments of this concept considered the exclusion of an integral number, of nearest-neighbor sites from being occupied at all concentrations. In this case, the partial configurational entropy is given by: These early treatments failed to allow for the overlap of the blocked sites which will arise at all but the very lowest concentrations. More recently attempts have been made to calculate the effect of this decrease in the number of blocked sites on the configurational entropy. Using the quasichemical treatment of interstitial solid solutions as given by Lacher and assuming that an infinite repulsive interaction energy existed between the solute atoms. atom obtained an approximate configurational entropy applicable to the blocking with overlap case:

Jan 1, 1970

By Alberto J. Terrones L.

THE classical papers on contact metasomatic deposits by Lindgren on the Clifton-Morenci district,1 by Barrel1 on Marysville, Mont.,2 and by Goldschmitt on the Oslo district, Norway,3 laid the foundation for understanding of the importance of separating the metamorphic process from the subsequent metasomatic stage. Knopf4 made a big step forward by recognizing that sulfide ore minerals are invariably younger than silicates and by further stressing the importance of structural control5 ore finding. Some years later Harrison Schmitt6 fought the idea that contact metasomatic deposits are erratic, irregular, bunchy, economically marginal, and of small size, concluding that these descriptions have little factual basis. He emphasized the importance of detail mapping and careful geological study as fundamental requirements for a better understanding of these deposits. This article presents a comparative description of the structural features at the Magistral, Antamina, Morococha, Vilca, Ferrobamba, Katanga (Quibio), Tintaya, and Huarca contact deposits (Fig. 1). Further, it will describe how these structural features controlled the emplacement of the intrusives, their shape, distribution of metamorphic and metasomatic halos, and sulfide deposition in post-skarn structural channelways. Finally, the modifications introduced by a superimposed hydrothermal stage recognized at some localities will be discussed.

Jan 3, 1958

A. G. Cockbain—The paper by Burlingame, Bitsianes and Joseph is of great interest in extending the work done on high grade sinters, particularly that of Hessle, and the development and application to them of the technique of McBriar, Johnson, Andrews and Davies on ironstone sinters. In this laboratory the work of McBriar et al. has also been continued and extended to cover high grade sinters, and a sectioning technique similar to that used by McBriar et al. was attempted on sinter cakes made in the laboratory sinter unit, using magnetite concentrates (containing 64 pct Fe). In these experiments no attempt was made to flush out the products of combustion with nitrogen before cooling. It was considered that free air penetration would occur on only a limited scale with the size of sinter cake made (14 in. sq x 12 in. deep). Chemical analyses of the zones showed generally similar features of those described by Burlingame et al. and especially the FeO rich region at and just behind the flame front, i.e. zones of ignition and combustion. This seems to indicate that the nitrogen atmosphere does not materially affect the states of oxidation in the sinter cake or at least that special care is not required unless the sinter cake is small. Burlingame et al. consider that FeO present has some significant part to play in the mechanism of sintering. This view does not find favor with the author. The reduction of iron oxides in the presence of red hot coke is a well known phenomenon, whether conducted in an atmosphere of nitrogen or in a crucible in air, and in view of the presence of some carbon in the hot sinter, especially just at the ignition zone, cessation of the progress of the flame front will in no way affect the reduction of iron oxides near hot coke. Even in a nitrogen atmosphere some CO and CO, will be generated by reduction and by continual oxidation and reduction of CO as the transfer agent, the oxidation state of the iron oxides can be lowered quite rupidly so long as free carbon exists with enough heat. Knowing the composition of the gas at the flame front (obtainable by probes), it would be possible to calculate the static oxidation state of Fe2O3/Fe3O2 in equilibrium with it and hence obtain a check on the chemical analyses to see if in fact direct reduction of the Fe2O3/Fe2O1 to FeO has taken place. Have the authors attempted this? It appears to this writer that what is required is some means of reducing rapidly the heat content of the ignition zone and immediately behind, and at the same time insuring no oxidation by the air. In ironstone sinters the difficulty of oxidation state of the iron did not arise on account of the very large slag bulk. However, in high grade sinters knowledge of this, and also the mechanism whereby high oxidation states can be obtained in the final sinter, is of great interest. R. D. Burlingame (author&apos;s reply)—The question has been raised as to whether the high FeO content found in high-fuel sinters is due to actual reduction at the advancing flame front or due to unavoidable direct reduction during the quenching period. For such direct reduction to have taken place in the freshly-formed sinter, a considerable amount of solid carbon would have had to escape combustion and be available throughout the hot sinter zone during the quenching period. A simple stoichiometric calculation with the limited data available indicates that a zone of freshly-formed sinter over 2 in. wide must have averaged roughly 2 pct C to accomplish the amount of reduction found. Furthermore, the presence of this amount of carbon would indicate that the fuel in the charge had not burned over a narrow front but over a zone at least 2 in. thick. In contrast to such a condition, the data of the present investigation indicate that the combustion of fuel is confined mainly to a narrow front in which high temperatures and reducing conditions favor. the formation of excess ferrous iron.

Jan 1, 1959

By T. S. Lundy, R. E. Pawel, F. R. Winslow, C. J. McHargue

The volume-diffusion coefficients of Nb-95 and Ta-182 in niobium have been measured over the temperature range 878° to 2400°C. High-temperature specimens (T 21500°C) were sectioned by conventional lathe and grinding techniques while low-temperature specimens were sectioned by an anodizing and stripping technique previously described. Over a range of more than ten orders of magnitude in diffusivity, the self-diffusion data is well-represented by the equation: D = (1.1+ 0.2) exp [- (96,000 * 900)/RT ] cm2/sec Upward deviations from this line are explained by short-circuit diffusion in combination with the loss of resolution of the sectioning techniques. Oxygen contamination within the range 100 to 450 ppm was found to have little or no effect on the self-diffusivitj 01 niobium. In a limited number of measurements, the diffusivity of Ta-182 in niobium was found to be about half that of Nb-95 in niobium. These data may be described by D = (I.0+0.90.5)exp [- (99,300 * 2400) /RT ] PREVIOUSLY reported studies of self-diffusion in niobium were by Resnick and Castleman1 and Peart, Graham, and Tomlin.2 The data of Resnick and Castleman over a temperature range 1585" to 2120°C show considerable scatter but. can be represented by D = (12.4 *0.8) exp [-(105,000+3OOO)/RT] cm2/sec The limited data of Peart, Graham, and Tomlin follow the equation D = 1.3 exp (-95,00O/RT) cm2/sec In view of recent diffusion data for ß zirconium3 and 0 titanium4 in which Arrhenius-type plots do not yield straight lines and of the potential high- temperature uses of niobium and its alloys, we thought it important to investigate the diffusion behavior of this bcc refractory metal over a large temperature range. This has recently been done for molybdenum,5 chromium,6 vanadium,"" and tantalum.9 Niobium was a particularly suitable material for this study largely because of the development of an anodizing and stripping sectioning technique which enables diffusivities as small as l0-19&apos; sq cm per sec to be determined accurately.10 In addition to self-diffusion data, data were obtained for the diffusion of Ta-182 in niobium and for the effect of varying oxygen content on self-diffusion. I) EXPERIMENTAL PROCEDURE Materials. The niobium was obtained from three sources: 1) melting stock from Shieldalloy Corp., 2) electron-beam melted single crystals, 1/2 in. diameter, from Semi-Elements, Inc., and 3) oxygen-doped, electron-beam melted single crystals from Materials Research Corp. The melting stock was electron-beam melted and specimens 5/8 in. diameter by 1/2 in. long were machined from the center of the bar. The analysis supplied by the vendor and an interstitial analysis of one of the specimens are given in Table I. The single crystals (type 2 above) were cut with a jeweler&apos;s saw to specimens about 3/8 in. long. The interstitial analysis of this material is given in Table 11. This material was used

Jan 1, 1965

PITTSBURG MEETING The One Hundred and Ninth Meeting of the Institute, for the presentation and discussion of technical papers, will be held at Pittsburg, Pa., Oct. 8, 9 and 10, 1914. This meeting is to be under the auspices of the Iron and Steel Committee, the Committee on Petroleum and Gas, the Committee on Coal and Coke, and the Committee on Non-metallic Minerals. Thirty papers have been secured by these Committees and will be presented at the meeting. These papers will be published in the September and October Bulletins. The Local Committee of Arrangements for this meeting is as follows: SAMUEL A. TAYLOR, Chairman. FRANCIS C. PHILLIPS. GEORGE S. RICE. C. F. V. Rys. KENNETH SEAVER. JOHN S. UNGER.

Jan 9, 1914

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer&apos;s patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly &apos;7&apos; according to one bibliography, Over go per &apos;ent were concerned with the metallurgical phase and less than &apos;0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer&apos;s patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly &apos;7&apos; according to one bibliography, Over go per &apos;ent were concerned with the metallurgical phase and less than &apos;0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By C. A. Stickels

A heat of electrolytic iron, to whzch alunzinutn and nitrogen had been added, was hot-rolled, cold-rolled 90 pct, and recrystallized at temperatures from 500" to 700°C. Primary recrystallization textures appear to arise from competitive growth of two types of nuclei: 1) those having orientations belonging to the "usual" primary recrystallization texture found in riming steel, and 2) those with the {111} (110) ovientation. Development of a (111}(1 10) component in the primary recrystallization texture occurs only over a certain interval of isothermal recrystallizatzon temperatures when the material is supersaturated with respect to the precipitation of AlN. Lowering the degree of supersaturation depresses the temperature interval in which a (111)(110) component occurs. An elongated, &apos;pancake-shaped" recrystallized pain structure and a marked delay in the start of recrystallization were found in all specimens which were supersaturated with respect to A1N precipitation after cold work, regardless of their recrystallization texture. ONE of the consequences of killing low-carbon steel with aluminum is a significant change in recrystallization behavior. About 15 years ago, Solter and eatttiel showed that this behavior was largely controlled by aluminum and nitrogen in the steel. If complete precipitation of A1N was prevented before cold rolling, an increased "recrystallization temperature" was observed in subsequent. annealing, and the recrystal-lized grains were not equiaxed. Leslie et a1.2 studied this phenomenon in some detail and clearly demonstrated the relationship between A1N precipitation, recrystallization kinetics, and the development of "pancake-shaped" grains. It has also been known for some time that aluminum-killed steels, processed to produce elongated "pancake" grains, develop a (11 I}( 110) primary recrystallization texture. This texture has not been found in iron or low-carbon rimming steel as a primary texture4j5 but has been observed following grain growth in electrolytic iron.5 The present work was undertaken to study in more detail the effect of A1N supersaturation on recrystallization textures in iron. LITERATURE REVIEW The deformation texture in heavily rolled iron has been studied in detail by Bennewitz.~ The texture consists primarily of a partial fiber texture about a (110) axis in the rolling direction, designated here as fiber texture A. It includes the range of orienta- tions (111)[110] - (001)[ 110] - (11l)[110]. A weak secondary texture also is present.6 This is a duplex partial fiber texture about two (110) fiber axes located 60 deg from the rolling direction and 30 deg from the sheet normal. The range of this texture, designated here as fiber texture B, about the [101} fiber axis is (112)[110] - near (545)[252] - (211:1[011] *The range given here follows Bennewit~.~ A few pole figures from re-crystallized material indicate a broader range than this.&apos; However, the components which are strongest in the recrystallization texture are in this range.&apos;________________________________________________________ Primary recrystallization textures in unkilled steels can be accounted for by growth of members of fiber texture B present in the deformed metal.5 However, while members of fiber texture B dominate the primary texture, other orientations survive primary recrystallization as well. In particular, some {111}(110) members of fiber texture A must also grow during primary recrystallization, because a well-defined {1ll)( 110) texture develops during subsequent grain growth at 700°C.5 The unusual recrystallization behavior of deformed supersaturated solid solutions has been attributed to: 1) retention of the solute in solution,&apos; 2) formation of coherent, preprecipitation solute clusters prior to and during re~r~stallization,~ and 3) formation of a precipitate prior to and concurrent with recrystallization.&apos;~-&apos;~ When aluminum is supersaturated with iron, the difference in grain boundary mobility between general high-angle boundaries and certain special coincidence site boundaries is apparently eliminated.&apos; In aluminum-killed steels, precipitation of A1N can take place at ordinary subcritical recrystallization temperatures. The rate of precipitation increases with increasing aluminum or nitrogen contents.2&apos;13 There is some doubt, however, as to whether true precipitates form during the time at temperature needed to complete recrystallization. Leslie ef a1.2 found that precipitation in one steel was complete after about 100 min at 700GC, or after about 1000 min at 650GC, as measured by chemical analysis for AlN. Aoki et a1.,13 using internal friction for dissolved nitrogen, showed that a large fraction of the dissolved nitrogen was removed from solution within a few minutes annealing time at temperatures from 400" to 800°C. However , the rate of formation of AlN, as detected bv chemical analvsis. was much slower than the apparent rate of nitrogen removal. Hasebe,&apos;~~ using carbon extraction replicas, has identified A1N precipitates by electron diffraction in a 0.2 C steel, solution-treated at 1300°C and annealed 2 hr at 700°C. Borchers and kim,I6 also using a replication technique, observed precipitates after annealing treatments as short as 2 min at 640°C. However, Leslie et a1.&apos; state that no A1N precipitate can be seen while recrystallization is being inhibited in aluminum-killed steel.

Jan 1, 1967