Search Documents

By B. J. Harlan

The trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than toward securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and-1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years. To decrease the velocity of gas through the throat of the furnaces, thereby reducing flue-dust losses, the stock-line areas are constantly being made larger. The top dimensions of the larger furnaces are usually as follows: Stock-line diameter, 19 to 20 ft.; large bell diameter, 14 to 15 ft.; straight section of throat, 5 to 10 ft. high; inwall batter, 1 to 11/4 in. Pe ft. The ratio between the area of the stock line and the area of the large. bell is usually about 1.85 to 1. The stock-line diameter of some smaller furnaces has been increased to that of the hearth diameter of the stack at the expense of the stack batter. Remarkable decreases in flue-dust production are claimed for the so-called " Venturi top," which is achieved by flaring the stock line, in the form of an inverted cone, from a diameter of 17 ft. at 10 ft. below the large bell closed to a diameter of 19 ft. 6 in. at 3 ft. below the large bell closed. Time alone will tell which of the two designs is the better. Because of differences in raw materials, one top may be better for some plants and the other top for other plants. In the search for lower costs and higher efficiencies all operators are, adopting stoves that will maintain maximum hot-blast temperatures with a minimum gas consumption. To meet these requirements, stove capacity of approximately 7 sq. ft. of heating surface and 1.8 cu. ft. of brick volume is required per cubic foot of wind blown per minute.

Jan 1, 1934

By Aloys H. Wohlrab

[THE conditions that govern the selection of a suitable type of detachable bit for the small isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may of be able to adopt the practice of larger mines because of necessary capital expendites for equipment for detachable-bit sharpening and shanking. The perfect detachable bit, suitable for all conditions, has n yet been developed. CONVENTIONAL DRILL BIT IN USE That drilling speed increases as the hit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests married out by Holman Brothers Limited1 with 7/8-in. show that when bit sizes are reduced from. 1 ½ in. 1 3/8 in., and 1 3/16 in., to 1 3/8 in., 1¼ in., and it' in., respectively, the volume of the hole is15 per cent less and the drilling speed 4q per cent higher. Recent tests by the United States Bureau of Mines2,3in hard, uniform basalt showed that a reduction in average gauge from 2.077 to 1.826 in., a difference of 0.251 in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr characteristics) by some mines.4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and I4° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as can be forged economically. Shop practices and costs have been discussed in earlier papers.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert.7 REQUIREMENTS FOR DETACHABLE BIT FOR HOLLINGER Under these circumstances, it was apparent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in]

Jan 1, 1942

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the sane. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known. GENERAL METHOD The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By Wm. C. Coffin

THE refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Not only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts clown the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bes-

Jan 2, 1919

By H. M. Strong

Nickel and carbon form a metastable nickel-nickel carbide eutectic system which was ohsen)able by freezing latent-heat arvests at pressures 210 khars. The eutectic freezing temperature Is pressure had a slope of -0.9°Cper kbar. At 50 khars, the nickel-nickel carbide eutectic was at 1297° * 5°C and 0.34 mole fraction Ni3C. The composition of the eutectic increased at an initial rate of 0.004 mol fraction per kbar. The carbon content of the a phase also increased with pressure. Seveval illustrations of nickel carbide microstruc-tures are given and data on the lattice expansion of nickel in terms of carbon content are included. IRON, cobalt, and nickel form a variety of carbides with compositions varying between MeC and MC. Of the three, the carbides of iron are most easily recovered. The nickel carbides are so unstable at temperatures above 900°C that their occurrence in Ni-C alloys is unusual. Under sufficient pressure, however, the temperature range for the stability of the ferrous metal carbides is likely to be increased, or their decomposition suppressed (e.g., see Hilliard' on FesC), providing an opportunity to study the unstable carbides more closely. This was found to be true for nickel carbide which, under pressure, formed a eutectic with nickel. This paper describes the conditions of formation of nickel-nickel carbide eutectic compositions and their subsequent recovery. Despite the comparative instability of the nickel carbides, something is already known about them through various chemical reactions at temperatures not exceeding a few hundred degrees, and from their recovery by the very rapid quenching of molten Ni-C alloys from temperatures of about 1450°C or above. At least four carbides of nickel have been reported: A discussion of the state of knowledge about Ni3C is given by ansen.' The studies of Morrogh and williams7 who obtained Widmanstatten nickel carbide structures and of sidorenko8 who first obtained nickel carbide eutectic structures are also of interest. Sidorenko used short heating times for molten nickel in a graphite crucible followed by very rapid quenching to obtain the eutectic structures. Long heating times produced only the nickel-graphite eutectic probably due to the presence of graphite crystals in the melt which nucleated graphite crystallization. According to the early work summarized by anssen,' nickel carbide may form at temperatures far above the melting point and may be recovered by very rapid quenching. More recently, Giardini and Tydings, working on diamond synthesis, found evidence for "free nickel carbide'' in high-pressure reactions carried to temperatures far in excess of the limit for diamond growth, followed by rapid thermal quench. They stated that nickel carbide was not found in association with diamond growth. In the present work, observations were made on the melting and solidification temperatures of Ni-C alloys as a function of composition, temperature, and pressure. The nickel-nickel carbide eutectic was found at pressures above 10 kbar and its variation with pressure followed up to 60 kbar. Nickel-nickel carbide microstructures were recovered by quenching under pressure from temperatures of about 1400°C and higher. The formation of nickel carbide structures under ordinary diamond-growing conditions was usually observed but the role of carbide formation as an intermediate step in diamond growth needs more study. EXPERIMENTAL METHODS The melting and solidification temperatures of various nickel-graphite compositions were observed by latent-heat arrests in the sample holder illustrated in Fig. 1. The samples were composed of mixtures of carbonyl nickel powder and National Carbon Co.'s SP-1 graphite packed to densities of about 6.4 g per cu cm. They were contained within

Jan 1, 1965

By Louis Ware

BEFORE the war we often heard the term "Big Business." And there were complaints of the ills and abuses attributed to bigness in business. Although there were examples where the small businessmen spoke for their rights and sought protection from the bigger ones, it has only been in recent war years that a tendency has developed definitely to divide the business of our nation into the big and the small. In some cases, those with an eye to the political value of the vastly greater number of small businessmen of the country have fomented this division by hurrying to the protection of these more numerous voters, and intentionally or not have emphasized in their writings and verbal attacks any and all differences of these interests that could either be found or fabricated to, suit the occasion. It has become another example of breaking the people into classes and thus setting up the basis for the claims of one class against another, and the subsequent demand for legislation and Governmental aid. The terms "big" and "small" are purely relative. One businessman, employing a hundred men, told me recently he did not know which adjective would be more appropriately applied to his operation. He did not know whether he should join the small operators' group that had been organized, or should consider himself big. He said that his present plant seemed big to him when he looked back to its humble beginning many years ago with a couple of men in two rooms. Yet, when compared with many of his competitors who employ thousands, his was small. He did add, however, that he probably became big one day a few years ago when the union moved in and organized his employees.

Jan 1, 1945

By Arthur Phillips

The progress made in recent years in the art of dispersion-hardening has naturally led to an intensive study of alloy systems capable of yielding supersaturated solid solutions at ordinary temperatures. In general, the investigations have been confined to rather precise determinations of solubility limits and to experimental approaches designed to furnish more complete information regarding the rate and nature of precipitation under appropriate thermal conditions. Efforts are being made to focus more sharply on the atomic changes that are a direct consequence of the instability of the supersaturated solution. Here precision X-ray methods have come to be of considerable importance because lattice parameter measurements indicate very precisely the concentration of solute atoms in the solvent lattice. In spite of the general acceptance of parameter values as a criterion for the placing of solubility limits, it may be suggested that no thorough appraisal has been made of the several factors that conceivably may affect such measurements. More specifically, little attention has been devoted to the significance of surface energy conditions, specimen size and method of preparation, with particular regard to the genesis of the grains and the surface concentration changes as a consequence of heat treatment and etching. Stenzel and Weertsl recently published the results of a detailed study of precipitation reactions in aluminum-rich copper alloys. They found that, although copper lowers the lattice constant of aluminum, a 5 per cent copper alloy quenched from 150" and 225' C. had parameter values unquestionably higher than that of pure aluminum. Their results seem to substantiate, at least qualitatively, the earlier work of von Göler and Sachs,2 who indicated a parameter value, for the same alloy annealed for 24 hr. at 200° C., some 0.0008Å. larger than that of pure aluminum. Stenzel and Weerts attributed the abnormal lattice dimension to the effect of strain induced by the precipitation of CuA12. Weerts3 later

Jan 1, 1934

By E. H. Kelton

The purposes of this paper are to describe the use of adjustable cut and draw tools as a control test of drawing properties and to point out that no other well-known test or combination of tests determines this quality in zinc and zinc alloys. Rolled zinc has been used for making drawn articles, particularly battery cans, for many years. The development of rolling treatments satisfactory for these purposes followed the usual course of trial and error experimentation depending upon cooperation with customers to determine what type of material was suitable. A quick test of drawing quality was highly desirable, of course. Scleroscope hardness and temperll having no apparent relation to drawing quality, were used simply to check the duplication of rolling treatment and grade of metal. The dynamic ductility1 test, on the other hand, was believed to be so like the drawing operation as to provide a reliable index and came to be taken as the criterion of good drawing properties. Faith in this test was strengthened by the fact that metal having the highest ductility was more satisfactory for operations, such as the manufacture of battery cups, that required several redraws. No distinction was made at that time in specifying metal as to whether it was to be subjected to simple cut and draw, redrawing or forming operations. It developed, however, that in some grades of metal the highest ductility did not coincide with the most satisfactory quality when the material was used for a single draw. When zinc-base alloys, with their wider ranges of effective rolling treatments, came into increased use, their dynamic ductility and drawing quality appeared to have no connection whatever. Furthermore, comparisons of known drawing quality with other physical properties of the metal, including tensile strength, elongation and dynamic cold bends, were fruitless in yielding any clear relationship. Almost any test value produced in one piece of metal could be duplicated by another rolling or annealing treatment with attendant different drawing characteristics.

Jan 1, 1934

By E. L. Jr. Spain

THE deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of. Mississippi and Alabama respec-tively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewell1 and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance.

Jan 1, 1936

By W. L. Dennen, W. W. Wirth

Research looking toward the reduction of the cost of roof support by substitution of longer-life materials for wooden timber is fully justified by the fact that roof support is an important element of all production costs. Permanent or semipermanent roof support will reduce the expense of timber-maintenance crews during steady operations, but even more markedly during idle periods. The management, therefore, is faced with the important problem of timber renewals, which in times of regular operation are frequently obscured by more urgent problems of production. Increased use of timber in the Anthracite Region of Pennsylvania is caused mainly by increased percentage of coal obtained from robbing areas, which requires more timber for safety than development work, and maintenance of long haulageways through crushed ground despite the fact that less coal is transported over them. The timber reserve in the immediate vicinity of the mines has been depleted to such an extent that it is necessary to secure 70 per cent of the timber requirements from distant sources. Originally, mine timbering in this region was done by largely utilizing round props or legs with round collars. The whole cross section of the tree from which timber was cut was utilized by forming the joints between the legs and the collars with saw and adze, using plank or round saplings for lagging behind the legs and over the collars to prevent material falling between them. The Mine Inspectors' report of 1898 records an important digression from the use of round timber, when two tunnels at the Babylon colliery, near Pittston, Pa., were timbered with 12 by 12-in. square timber sets with mud sills, through quicksand for distances of 425 and 160 ft., respectively. The timbers were lagged with 3-in. plank to control sand. An early step toward the permanent type of roof support was the installation of "brick pillars or perfect arched brick rooms" instead of

Jan 1, 1940

By W. L. Dennen, W. W. Wirth

Research looking toward the reduction of the cost of roof support by substitution of longer-life materials for wooden timber is fully justified by the fact that roof support is an important element of all production costs. Permanent or semipermanent roof support will reduce the expense of timber-maintenance crews during steady operations, but even more markedly during idle periods. The management, therefore, is faced with the important problem of timber renewals, which in times of regular operation are frequently obscured by more urgent problems of production. Increased use of timber in the Anthracite Region of Pennsylvania is caused mainly by increased percentage of coal obtained from robbing areas, which requires more timber for safety than development work, and maintenance of long haulageways through crushed ground despite the fact that less coal is transported over them. The timber reserve in the immediate vicinity of the mines has been depleted to such an extent that it is necessary to secure 70 per cent of the timber requirements from distant sources. Originally, mine timbering in this region was done by largely utilizing round props or legs with round collars. The whole cross section of the tree from which timber was cut was utilized by forming the joints between the legs and the collars with saw and adze, using plank or round saplings for lagging behind the legs and over the collars to prevent material falling between them. The Mine Inspectors' report of 1898 records an important digression from the use of round timber, when two tunnels at the Babylon colliery, near Pittston, Pa., were timbered with 12 by 12-in. square timber sets with mud sills, through quicksand for distances of 425 and 160 ft., respectively. The timbers were lagged with 3-in. plank to control sand. An early step toward the permanent type of roof support was the installation of "brick pillars or perfect arched brick rooms" instead of

Jan 1, 1940

By P. G. Shewmon

If interfacial equilibrium is maintained at the interface between a growing precipitate and the supersaturated matrix, so that solute diffusion alone determines the growth rate, the precipitate shape should evolve toward that characteristic of the dendrites found in solidification. However, this shape is rarely observed in precipitation reactions proceeding at high temperatures where interfacial equilibrium is usually felt to prevail. Thus some other stabilizing factor must enter, to keep the interface smooth. It is shown that a slow interfacial reaction (low interfacial mobility) will stabilize the interface, while transformation stresses have a IN studying the kinetics of phase transformations such as solidification or proeutectoid precipitation at high temperatures, it is customary to assume that equilibrium exists across the interface and that the rate of the reaction is determined by the rate at which heat and solute diffuse to and from the interface. In the case of precipitation, such an assumption predicts an almost infinite rate of initial growth. It is generally stated that the rate cannot be infinite and that during some initial period the rate must be determined not by solute diffusion but by an interfacial reaction, i.e., transferring atoms across the interface. The duration of this much weaker stabilizing eFfect and impurities tend to enhance instability. It is also concluded that a sets an upper limit on the wavelength of the perturbation that can give instability. Thus initially all flat or smoothly curved particle interfaces will be stable even if their growth is diffusion-controlled. Proeutectoid precipitation in the Fe-C system is considered in some detail and it is shown that the experimental results can only be rationalized if the growth rate of ferrite in steel transformations is determined by a slow interfacial reaction for all hut a few orientations between the two phases. initial period has never been clearly established, but it is generally assumed to be too short to affect any measurable results.' Several authors have pointed out that in the case of interfacial equilibrium any bump in the surface will grow out ahead of the planar interface due to the higher gradient in front of it.2j3 Thus the interface will be unstable with respect to an irregular interface with points (plates) propagating rapidly out ahead of the interface into the supersaturated phase. Recently, Mullins and Sekerka have given equations for the stabilizing effect of surface tenion.~ They found that for particles with a radius of curvature of 1 p or greater the stabilizing effect of surface tension will be completely overcome by a supercooling, or supersaturation, of as little as

Jan 1, 1965

By J. G. Bouwkamp

This paper presents three general approaches towards the solution of the stress distribution and the behavior of tubular connections as used in offshore well drilling structures. First, the possibilities of using plastic models and photoelasticity techniques in evaluating the stress distribution in gusset plate connections are analyzed. The results of photoelastic studies on the stress distribution in the in-plane gusset plate of two-dimensional joints are presented. The influence of the configuration of the gusset plate (with and without cut-outs) is discussed. Second, the paper deals with recent developments and applications of computer programs to analyze connections with directly inter-welded tubes and with gusset plates. The possibilities and limitations of these programs are discussed. Stress patterns analyzed with these programs are presented for different joint configurations. Finally, the basic test procedures and results of a test on a tubular joint under static and alternating loads are discussed. INTRODUCTION The effective design of tubular connections as encountered in offshore well drilling towers or floating platforms has been complicated basically by the radial flexibility of the tube walls. This flexibility is a source of severe stress concentrations which can initiate an early failure of these joints. In an attempt to reduce the influence of the wall flexibility of the column tube, certain joints are presently designed by inter-welding the incoming branch members. In those designs, the force acting normal to the chord tube can be reduced considerably. A second group of joints incorporate gusset plates or stiffening rings to stiffen the column wall and to distribute the incoming branch member forces over a larger part of this wall. A third approach to improve the stress distribution in a tubular joint is to increase the wall thickness of the column member. This can be achieved by simply applying a thicker wall section in the vicinity of the joint. A fourth possibility to restrain the radial flexibility of the tube wall is to fill the column member with concrete. Also, a single, cast steel seat welded to the column tube can be used to improve the stress distribution in this wall. Although all these designs improve, in general, the state of stress in the column wall, the altered stiffness often causes the development of critically stressed areas in the web members. At the same time the actual design in most instances is decisively influenced by the site which governs the depth and controls the forces produced by waves, earthquakes and ice flow. Also, the towing, erection and foundation requirements of offshore structures can affect the actual design selection. Because of the complexity of the structural configuration of tubular joints, the stress analysis of these connections has necessarily been based on simplified and often crude assumptions. For the earlier and smaller type of connections with about 4-ft diameter column sections, the primary problem was to evaluate the relative stiffness of the column wall section and the load transfer between joint members. Due to the recent developments of offshore drilling structures with increasingly larger connections (e.g., column diameter. 32 ft; web members, 8.5 ft) this problem has become even more critical. One design philosophy for such large joints follows a member-to-member connection with radially heavy reinforced column sections. This radial stiffness can be attained by closely spaced and intensively stiffened horizontal diaphrams together with vertical stiffeners. A second solution incorporates a concrete-filled section between the outer and inner walls of the column tube. Another philosophy considers large gusset-plated joints. The problem in these joints is to develop an effective load transfer between the branch tubes and the gusset plate and to minimize the stress concentrations in the member walls as effectively as possible. Several concepts are followed to achieve this gradual transfer between web-member walls and gusset plates. Because the number of joints in these huge platforms is limited compared to the over-all size, a proper design of these joints is even more important than was the case for the many joints in the smaller, but multi-legged towers. A failure of one of those ultra-large joints could well cause the complete collapse of such a structure. Under these circumstances an accurate analysis of the large joints is of the greatest importance, together with information regarding the expected behavior of such joints under critical alternating load conditions. Recent applications of photoelastic model techniques have proved to be quite effective in evaluating the elastic behavior of such joints. Although a complete study of such connections is quite well possible with present-day photoelastic techniques, it might often be feasible and necessary to limit the objectives and to restrict these investigations to the study of a specific aspect of the joint. Another very promising avenue of approach to solve the complex stress pattern in these connections seems to be the recent development of digital computer programs. In this category, cylindrical shell programs and finite element methods for more complex configurations have

Jan 1, 1967

By J. Kucera, J. Vreštál

DIFFERENT authors1 ' have been engaged in meas-uring the vapor pressure of pure cobalt. The results of their measurements satisfy the expected temperature dependence of vapor pressure and are in mutual agreement, with the exception of the results by De Dyk Man and ~esmejanov.~ The latter authors, by using the effusion method, have achieved considerably higher values than other workers. By using the isotope exchange method they obtained much lower values than other authors. The determination of thermodynamic functions of the binary Ni-Co system was carried out, as far as we know, only by De Dyk Man and Nesmejanov.4 This determination was based on extremely low values of vapor pressure over pure cobalt obtained by the isotope exchange method. Therefore we considered it useful to repeat these measurements. Furthermore, the reliable values of thermodynamic functions should complement the migration characteristics, the inner magnetic field data obtained by Miissbauer effect measurements, specific heat data, and the K effect and positron annihilation characteristics that have been achieved for the Ni-Co system in the Institute of Metallurgy of the Czechoslovak Academy of Sciences in Brno.5-9 The measurements in this paper were performed by the isotope exchange method. In this method, as has been shown by analysis,10-'3 the vaporization rate, w, can be calculated from the relation w = k/1oSw [1] i0Sw) [1] where L, is the activity per unit mass of the source, S is the area of evaporation, k is the tangent at the point t = 0 to the curve giving the radioactivity de-pendence of the target vs annealing time, t, and wis the probability for the tracer atom condensation on the target surface. The value for cc. can be obtained from the equation w = a + 2P(l-a) [2] where P is Clausing's coefficient and a is the condensation coefficient. In the present work the cylinder shaped containers for annealing the samples were used, characterized by the ratio 1:d = 1.06. Here 1 is the length and d the diameter of the container. For this ratio P = 0.514 and w =0.5, and w is independent of the condensation coefficient. The vaporization rate is related to the vapor pressure p by the relation where R is the gas constant, T is the absolute temperature, and M is the molecular weight of the component investigated. Measurements of the vapor pressure of the i component over the pure metal, p!, and the alloy, pi, at the given temperature and composition enable one to calculate the thermodynamic activity of this component from the equation ai=pi/pi [4] is and the activity coefficient ri=ai/xi [5] xi where xi is the molar fraction of the investigated alloy component. EXPERIMENTAL Evaporization rate measurements were carried out with pure cobalt and eight different Ni-Co alloys, which were kindly delivered by the Centre National de Recherches Me'tallurgiques Liege, Belgium. The composition of the alloys is given in Table I. The cobalt used in these alloys contained the following impurities: 0.016 wt pct Fe, 0.014 wt pct Cu, 0.01 wt pct Mn. Other elements were present in much lower concentrations. From the melts, samples in the form of small cylinders of 12 mm in diam were ma-chined. The thickness of the targets and sources was 2.5 and 1.2 mm, respectively. The lower thickness of the sources was chosen to make their over-all ac-tivity as low as possible. Sources were activated in

Jan 1, 1970

By E. H. Sellards

PHOSPHATE rock like most other mineral substances is found in nature in varying degrees of purity. Of the impurities that are present some are constituents of the rock itself; others are inclusions of a foreign substance within the rock; while still others represent merely associated materials or minerals, either clinging to the rock or found in cavities and natural depressions, and hence largely removed in mining. Some of these impurities are distinctly deleterious to the processes of manufacture for which the phosphate is mined, while others, although neutral in action or nearly so, yet by their presence reduce the average grade of the rock and thus acid useless bulk to the shipment. It is the object of refined processes of mining to bring the product, as delivered from the mine, to the highest possible grade consistent with the market requirements and demands. This, however, is not accom-plished without actual loss in the form of discarded phosphate. It is evident, therefore, that the devising of methods for reducing this loss in mining, and yet maintaining the grade of the rock which the market requires, is one of the serious problems that the producers have to face.

Jan 9, 1914

By Harry Bapty

LONGHOLE drilling with a heavy type percussion Leyner drill, jointed steel rods, and a tungsten carbide insert bit was investigated while drilling and working a quartz barite brecciated rock. Procedure and practice were developed and its suitability for tackling pillar and sill recovery proven and extended to regular stoping at Torbrit. Torbrit, as the name implies, is a contraction of the Toric property and the Britannia Mining & Smelting Co. Ltd., the former owners. This silver property, with minor amounts of lead, zinc, and rarer sulphides of little or no economic value, was discovered in 1916 from an outcrop in the Kitsault River, 18 miles north of Alice Arm Post Office, in the Portland Canal Mining District, B. C.

Jan 11, 1954

By J. Nutting, D. H. Kirkwood

The oxidation of lead sulfide in air between 200° and 350°C has been investigated by electron diffraction from thick sulfide films and from galena surfnces. It has been demonstrated that sulfate is the stable reaction product up to 570°C. Sulfate is HAGIHARA has investigated' single crystals of galena roasted in air by the reflection electron-diffraction technique, which owing to the very limited penetration of the beam into the crystal gives information of the nature of the surface only. He has shown that up to 280°C the first oxidation product is lead sulfate, followed by lead mono-oxysulfate (PbO . PbS04). At longer times and higher temperatures more complex patterns appeared which could not be analyzed. All of these patterns were of streaks or spots arising from crystals oriented on the galena surface, and it is probable that these crystals are lead compounds whose structures have not been determined, such as the other oxysulfates (2Pb0 • PbS04 and 4Pb0 . PbS04) or a number of oxides. Certain lead sulfide films, formed chemically, give ring patterns in transmission electron diffraction2 because they are polycrystalline, and should also give ring patterns of the products after oxidation. It was thought that a diffraction study would reveal the sequence of phases produced in the reactions at different temperatures, since X-ray powder patterns are available for many lead compounds. PREPARATION OF FILMS The films were prepared by passing H2S over a saturated solution of lead nitrate in water. Once a silvery film had formed on the solution surface, no further thickening was apparent. The films were transferred by a gauze to a bath of distilled water for washing and pieces of film were caught on small discs on which they were dried. The discs were formed initially on galena up to temperatures of 300°C, followed by oxide and oxysulfates in turn at longer times. The appearance of- these phases is believed to result from an inadequate rate of supply of sulfur to the top surface 01. the crystal. standard Siemens mounts, made of platinum alloy, and had seven 20-p apertures drilled through them. The parts of the film which had dried onto the disc surface were light blue in color, which is the interference color of a film about 600A in thickness. A strong pattern of lead sulfide was obtained in transmission electron diffraction through the apertures but slight broadening indicated a crystallite size of around 200A. Tilting a sulfide film in the beam produced arcing of the rings, increasing the intensities of the (Ill), (3111, and (222) rings and reducing (200) and (220). This arises from preferred orientation in the film, a [loo] direction of the crystallites being normal to the plane of the film. These specimens were oxidized in an oven maintained at the required temperature. The reported times include that taken to heat the film to the reaction temperature. STABLE PHASES FORMED IN OXIDATION The conditions in which various oxidation products of lead sulfide are stable have been considered by the authors in a previous paper.3 It was shown that in a normal atmosphere, taken as containing lo-' atm of SOs, lead sulfate would be stable up lo about 570°C. This was confirmed by oxidizing thin films of sulfide for several days, and the analysis of the transmission-diffraction pattern is given in Table 1. The fit with the patt$rn from X-rays is good, except for the missing 3.62A ring. Some disagreement in intensities of reflections given by X-rays and electrons is to be expected. Up to 570°C a spotty pattern of sulfate was still obtained, indicating grain growth, but above this temperature the film disintegrated. Probably this is associated with the decomposition to PbO . PbS04. It needs to be emphasized that the atmosphere

Jan 1, 1965

By Arthur B. Cummins

Mineral fillers are employed in United States industries to the extent of more than seven million tons annually, valued in excess of a hundred million dollars. This substantial usage involves a wide variety of mineral materials. To this may be added products manufactured from minerals, such as carbon black, portland cement, lime or chemically precipitated calcium carbonates, which would add substantially to the total. The purposes for which fillers are used differ considerably. Minerals used as fillers are mostly silicates, silicas, and carbonates as referred to hereinafter. The term "mineral filler" has various meanings in mineral technology and in the arts. Fillers are comparatively inert and their action is mainly physical. Materials that are employed primarily for chemical reactivity, or for pigment or abrasive functions ordinarily would not be considered to be fillers when used for these purposes. Nearly all filler usages are based on advantages which are gained by desired modification of composition properties or by improvements in processing. A simple definition for a filler is an inert material that is included in a composition for some useful purpose. This definition may be amplified or made more specific for each of the filler usages, the major ones of which are: paints, paper, plastics, rubber, bituminous compositions, pesticides and fertilizers. There are in addition a whole host of minor usages. Powdered minerals when employed as components in paints, varnishes and lacquers are considered as extender pigments or low refractive index pigments. In paper, the term loading material as well as filler is used; in pesticides, the terms diluents and carriers connote different functions. For bituminous compositions, rubber and plastics, the usage of the simple word "filler" is more usual, but the designation loading material is sometimes used. Minerals Used as Fillers Most of the industrial minerals, and many rock powders are employed to some extent for different filler uses. These usages vary from year to year depending on availabilities, costs, technologic trends and advancements. For the major applications, however, and for the more particular requirements at any given period, there are general trends which favor a more or less restricted group of filler products for each of the major consumer fields. This selection of materials is determined by the characteristics of the individual filler products, their effectiveness in fulfilling the primary function or functions for which they may be employed, and the cost after incorporation in the finished product. The mineral-bearing materials of major importance as fillers are: limestones, clays of several types, talc, pyrophyllite, mica, barite, diatomite, crystalline silicas, asbestos, slate and other rock dusts. Others of secondary importance include: gypsum, vermiculite, phosphate rock, perlite, and pulverized wastes, such as slag and fly ash. A considerable number of other minerals are used to lesser extent. Among these minor mineral materials are: feldspar, pumicite, wollastonite,18 tripoli, nepheline syenite,6 coal, altered volcanic rock and others.2 Indeed, most mineral materials, when reduced to fine particle size may have some potential usage as fillers, depending on their properties, availability and price. On the other hand, the more exacting filler requirements

Jan 1, 1960

By John R. Lotz

DEVELOPMENTS in Iran currently arousing interest in a considerable portion of the world, particularly on the part. of that country's immediate neighbor on the North and in our own country, an inseparably related to and largely dependent upon the government's attempts to strengthen its economy and improve the standard of living of its people. These efforts are encompassed by provisions of the Seven-Year Development Plan recently enacted and not, in the process of implementation. It is a fine example of what one financially sound but extremely backward and poorly equipped country has undertaken to do on its own account and with its own resources. This Seven-Year Plnil was formally authoriztld by an act of the Iranian Parliament in February 1948. Its stated objects are to carry out such plans for the development of the country and its economy as ail1 raise the standard of livinc: and standard of education of the people, and re- duce the cost of living. A seven-yrar program for carrying out the work within the limits of appropriations was assigned under the law. The total amount to be expended during the seven- year period was fixed at the equivalent of $670 millioil at current rates of exchange.

Jan 1, 1950

By Carl Swartz

FOR many years kettles used in the melting and refining of lead and other nonferrous metals and alloys have been made of cast iron. The logic of this probably lies in the fact that cast iron has been known as a material of construction for vessels of this type much longer than steel, and satisfactory fabrication from it has been more easily accomplished and better understood. As the capacity of lead refineries has increased, it has been only natural to increase the size of kettles. Today kettles of 150 to 250 tons are not uncommon. As the size of the kettles increased and better shapes were designed, the uniformity of material of construction became more important. Records kept over comparatively long periods of time have shown that the length of service of kettles has not been uniform. Many causes contribute to this and the importance of each has not yet been evaluated. Kettle design, kettle setting, method of firing and material of construction have been changed from time to time to obtain better service, but the variation in length of service is still great. A kettle may fail during the first few heats or may last through more than one thousand heats. The purpose of this article is not to present the conclusions of a finished piece of research on kettle manufacture and use, but to present a series of observations made over considerable time in the hope that others will publish data and that all may be correlated into a logical scheme which will result in better service and longer kettle life.

Jan 1, 1931