Search Documents

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By W. C. Elli, M. E. Fine

YOUNG'S modulus of elasticity in metals ordinarily decreases with rising temperature. The range of the thermoelastic coefficient at room tem- 1/E dE/dT perature (temperature coefficient of modulus, is illustrated1 by the values for tungsten and hard-drawn aluminum, —95 and —1220x10-6 eg C-1. However, a nearly zero thermoelastic coefficient is observed in some ferromagnetic alloys over a limited temperature range. In these alloys, as the temperature is raised, an increase in modulus arising from loss of ferromagnetism compensates the normal decrease. Iron-nickel alloys containing 36 to 52 pct Ni behave in this manner. In the present investiga- tion, the dependence of the modulus and thermo-elastic coefficient on cold working and annealing were studied in iron-nickel alloys in this range of nickel. Although these alloys, when fully annealed, have a coefficient near zero over a very small temperature interval, the temperature range of low coefficient can be extended greatly by straining and then stress-relief annealing. The modulus of face-centered cubic iron-nickel alloys annealed at 1000°C does not vary linearly with composition at room temperature but, as shown by the solid line of fig. 1, from Koster,' is minimum at 40 pct Ni and maximum at 87 pct Ni. The modulus increases with applied magnetic field but retains the minimum near 40 pct Ni. Schematic change of modulus with temperature for three compositions is shown in fig. 2.'. ' With increasing temperature, the slope becomes less negative, goes through zero (temperature of minimum modulus for the alloy), becomes positive, and resumes its normal negative value above the Curie

Jan 1, 1951

By S. Terry, J. G. Munro

A unique feature of the recently dedicated pelletizing complex of Hamersley Iron Pty. Ltd. is the dry grinding circuit for the iron ore fines. This facility, located at Dampier, some 800 miles north of Perth, Western Australia, has a rated annual capacity of 2 million tpy of iron ore pellets. The Mt. Tom Price orebody, which supplies the pelletizing plant, is a massive deposit of high-grade hematite containing an estimated 500 million tons of ore averaging 64% iron. The main impurities are ferruginous shales that occur in bands of varying widths in the orebody. An average analysis shows 4.4% SiO2, 2.0% A12O3, 0.05% P and 1.8% LOI.

Jan 5, 1968

By G. Derge, Ling Yang, G. M. Pound

The specific conductance and its temperature dependence were measured over the entire composition range of the molten Cu2S-CuCI system. At a typical temperature of 1200°C, 10 rnol pet of the ionically conducting CuCl reduced the specific conductance from about 77 ohm-lcm-l for pure Cu2S to about 32 ohm -1cm -1, and 50 mol pet CuCl reduced the conductance to that for pure CuCI—about 5 ohm 1cm1. The nature of electrical conduction in molten Cu2S, FeS, CuCI, and mixtures was studied by measuring the current efficiency of electrolysis at about 1100°C. The Cu2S, FeS, and mattes were found to conduct exclusively by electrons, but addition of 1 5 wt pet CUS to Cu2S produces a small amount of electrolysis. Addition of CuCl to Cu2S suppresses electronic conduction, and ionic conduction reaches almost 100 pet at a CuCl concentration of about 50 mol pet. These facts are interpreted in terms of electron energy level diagrams by analogy to the situation in solids. RESULTS of electrical conductivity studies on molten Cu-FeS mattes as a function of composition and temperature have been reported.' The specific conductances ranged from about 100 ohm-' cm-' for pure Cu2S to 1500 ohm-' cm-1 for pure FeS. This is in sharp contrast with the low specific conductance of molten ionic salts for which the transfer of electricity is by migration of ions in the field. In general, these ionically conducting molten salts, such as NaC1, KC1, CuC1, etc., have a specific conductance of the order of magnitude of 5 ohm-' cm-'. It was concluded on the basis of this evidence that molten FeS and Cu,S exhibit electronic conduction. Pure molten FeS has a small negative temperature coefficient of specific conductance, resembling metallic conduction, while pure molten Cu2S has a small positive temperature coefficient, resembling semi-conduction. The molten Cu2S-FeS mattes follow a roughly additive rule of mixtures, both with respect to specific conductance and temperature coefficient. Savelsberg2 has studied the electrolysis of molten Cu2S and Cu2S + FeS. He concluded that while molten Cu2S is an electronic conductor, there is some ionic conduction in molten Cu2S + FeS3 owing to the formation of the molecular compound 2Cu2S.FeS and its dissociation into Cu1 and FeS2-1 ions. The present work does not verify his results. Chipman, Inouye, and Tomlinson" have studied the specific conductance of molten FeO and report a high specific conductance, about 200 ohm-1 cm-1 of the same order of magnitude as that found for molten mattes, and a positive temperature coefficient. They interpret these results in terms of p-type semiconduction in the ionic liquid by analogy to the situation in solid FeO.1 imnad and Derne' detected appreciable ionization in molten FeO by means of electrolytic cell efficiency measurements. In order to verify the conclusion that electrical conduction in molten Cu2S and mattes is electronic, and to gain further insight into the structure of molten sulfides, the following investigations were carried out in the present work: 1) The specific conductance, s of the molten system Cu2S-CuC1 was measured as a function of temperature over the entire composition range. As discussed later, molten CuCl is an ionic substance. It was thought that if molten Cu2S were simply ionic in nature, addition of small amounts of CuCl might not have a catastrophic effect in lowering the high conductance of the Cu2S. On the other hand, if much electronic conduction occurs, addition of the ionic CuCl should have a large effect in destroying the electronic conduction. 2) The electrolytic cell efficiency of the following molten systems was measured at about 1100°C in specially designed cells: Cu3; Cu2S + FeS, 50:50 by wt; FeS; Cu2S + CuS, 15 wt pet; Cu2S + CuC1, 5.9 to 46.4 mol pet; and CuC1. This gives a direct measure of the fraction of current carried by ions in these melts. Further, the cell efficiency, extrapolated to zero ionic current, is given by cell efficiency = (s leasile + s elexstronic). [1] s lucile for molten CulS would be expected to be no greater than that for molten CuC1, whose s lonle is about 5 ohm-' cm-1, as will be seen in the following. u,.,,.,.,.......for molten Cu,S is of the order of 100 ohm-' cm-'.' Thus, a large increase in cell efficiency from 0 to values of 10 to 100 pet upon addition of CuCl to Cu2S would indicate destruction of the electronic conductance. Conductance Measurements Experimental Procedure—The apparatus and experimental method were the same as those described in detail in connection with the study of electrical conduction in molten Cu,S-FeS mattes.' A four terminal conductivity cell and an ac poten-

Jan 1, 1957

By Jr. D. C. Williams, D. V. Carter

The four new oil-field discoveries made in the East and East Central Texas districts during 1941 were the East Long Lake field, Anderson County; Pickering field, Shelby County; Pleasant Grove field, Rusk County, and Tri-Cities field, Henderson County. The discovery of oil production in the Pettit lime of the Lower Glen Rose was made in the Groesbeck (Barron) field in Limestone County and the Willow Springs field in Gregg County. Important extensions were made to the Pittsburg field, in Camp County, the Chapel Hill field, in Smith County, and the Hawkins field, in Wood County. The Hawkins field was extended sufficiently to more than double the number of proved surface acres. As usual the East Texas field led the district in the number of completions for the year. The second most active field during the year was the Hawkins field, with 250 new wells completed. The third most active was the Long Lake field, in which 50 wells were completed. Approximately 964 wells were completed in the district during 1941. Production and Probation The district is credited with having produced 163,566,695 bbl. of oil and distillate during the year. This represents a decrease of 4 per cent from the 170,424,685 bbl. of oil and distillate produced during the preceding year. The production of 130,378,620 bbl. of oil and distillate from the East Texas field represents 79.7 per cent of the total production of the district; that is, 6.3 per cent less than the production for the year 1940, The district had an estimated basic daily allowable of 614,982 bbl. of oil on Dec. 31. Approximately 33 per cent of the state's annual production was produced in the district, compared with 34.9 per cent for 1940. Since the majority of the fields in this district are subject to proration, any change in the annual production is attributable largely to changes in proration schedules and number of shutdown days. Fields subject to shutdown days were closed in for 113 days during the year, with the exception of the East Texas field, which was shut down 111 days. An order was promulgated by the Oil and Gas Division of the Texas Railroad Commission for encouraging the disposal of salt water and reservoir-pressure maintenance in the East Texas field. Discoveries Tex Harvey Oil Company'sNo. I S. E. J. Cartmel was completed as the discovery well for the East Long Lake field, Anderson County. Production was found in the Woodbine sand, the horizon from which the Long Lake field produces. The Pickering field, Shelby County, secures its production from the Nacatoch sand, found at an approximate depth of 1510 ft., in A. E. McKiernan's No. I, Pickering Lumbering Co. This field is in an area near the state line in which a number of relatively unimportant and

Jan 1, 1942

By Jr. D. C. Williams, D. V. Carter

The four new oil-field discoveries made in the East and East Central Texas districts during 1941 were the East Long Lake field, Anderson County; Pickering field, Shelby County; Pleasant Grove field, Rusk County, and Tri-Cities field, Henderson County. The discovery of oil production in the Pettit lime of the Lower Glen Rose was made in the Groesbeck (Barron) field in Limestone County and the Willow Springs field in Gregg County. Important extensions were made to the Pittsburg field, in Camp County, the Chapel Hill field, in Smith County, and the Hawkins field, in Wood County. The Hawkins field was extended sufficiently to more than double the number of proved surface acres. As usual the East Texas field led the district in the number of completions for the year. The second most active field during the year was the Hawkins field, with 250 new wells completed. The third most active was the Long Lake field, in which 50 wells were completed. Approximately 964 wells were completed in the district during 1941. Production and Probation The district is credited with having produced 163,566,695 bbl. of oil and distillate during the year. This represents a decrease of 4 per cent from the 170,424,685 bbl. of oil and distillate produced during the preceding year. The production of 130,378,620 bbl. of oil and distillate from the East Texas field represents 79.7 per cent of the total production of the district; that is, 6.3 per cent less than the production for the year 1940, The district had an estimated basic daily allowable of 614,982 bbl. of oil on Dec. 31. Approximately 33 per cent of the state's annual production was produced in the district, compared with 34.9 per cent for 1940. Since the majority of the fields in this district are subject to proration, any change in the annual production is attributable largely to changes in proration schedules and number of shutdown days. Fields subject to shutdown days were closed in for 113 days during the year, with the exception of the East Texas field, which was shut down 111 days. An order was promulgated by the Oil and Gas Division of the Texas Railroad Commission for encouraging the disposal of salt water and reservoir-pressure maintenance in the East Texas field. Discoveries Tex Harvey Oil Company'sNo. I S. E. J. Cartmel was completed as the discovery well for the East Long Lake field, Anderson County. Production was found in the Woodbine sand, the horizon from which the Long Lake field produces. The Pickering field, Shelby County, secures its production from the Nacatoch sand, found at an approximate depth of 1510 ft., in A. E. McKiernan's No. I, Pickering Lumbering Co. This field is in an area near the state line in which a number of relatively unimportant and

Jan 1, 1942

By H. H. Uhlig

A study of passivity in chromium-iron alloys holds considerable interest, both because of the present-clay practical importance of the stainless steels, and because of the scientific importance attached to the mechanism of their corrosion resistance. Upon the discovery of the passive chromium-iron alloys in 1912, it seemed logical to attribute the observed phenomenal corrosion resistance to a thin, continuous, protective reaction product on the surface. The product was thought to be Cr2O3 or a similar oxide containing both chromium and iron. This mechanism seemed likely in view of Michael Faraday's conjecture that passive iron is not reactive in concentrated nitric acid because of an oxide on the metal surf ace. Since 1912, data have accumulated that permit a further exploration into the nature of passivity and provide a new approach to the problem. A summary of the facts lends considerable weight to a mechanism based not on physical protection of an oxide or similar compound, although such compounds may be present on the surface, but to a change in tendency of surface metal atoms to react chemically. This change in reaction tendency is ascribed to chemisorbed films that effectively satisfy residual valence forces of the metal surface, but do not appreciably disturb the positions of metal atoms in the lattice. In other words, formation of a new lattice such as that of an oxide is not a necessary condition for this type of passivity. The decreased reaction tendency of the metal by reason of chemisorbed films can thereby account for low reaction rates of the stainless steels in many media, as well as a noble galvanic potential as is observed. Substances capable of adsorbing on the stainless steels, and hence accompanying the property of passivity, are typically oxygen, nitrites or chromates, but are not in any sense limited to these. Other elements and compounds can also chemisorb, and therefore may also play a major part in the mechanism of passivity in specific media. The mechanism of passivity based on chemisorption or activated adsorption begins with the interpretation Langmuir proposed for his experiments concerning adsorbed oxygen on tungsten.' He found that adsorbed oxygen was tightly bound, remaining on the tungsten surface above temperatures at which WO3 rapidly volatilizes. The oxygen in such a state did not readily react with hydrogen even at

Jan 1, 1949

By W. E. D. Stokes

The faster that aircraft fly the sooner some new and stronger material must be found to take the place of the present aluminum alloy used in all-metal planes. Experts of the National Advisory Committee for Aeronautics. in studying hi-speed aircraft, are convinced that the present all-metal plane, of semi-monocoque, aluminum alloy construction, is not the ultimate in aircraft design. Magnesium alloys and steel are under consideration.

Jan 1, 1942

By Herbert H. Uhlig

A STUDY of passivity in chromium-iron alloys holds considerable interest, both because of the present-day practical importance of the stainless steels, and because of the scientific importance attached to the mechanism of their corrosion resistance. Upon the discovery of the passive chromium-iron alloys in 1912, it seemed logical to attribute the observed phenomenal corrosion resistance to a thin, continuous, protective reaction product on the surface. The product was thought to be Cr2O3 or a similar oxide containing both chromium and iron. This mechanism seemed likely in view of Michael Faraday's conjecture that passive iron is not reactive in concentrated nitric acid because of an oxide on the metal surface.† Since 1912, data have accumulated that permit a further exploration into the nature of passivity and provide a new approach to the problem. A summary of the facts lends considerable weight to a mechanism based not on physical protection of an oxide or similar compound, although such compounds may be present on the surface, but to a change in tendency of surface metal atoms to react chemically. This change in reaction tendency is ascribed to chemisorbed films that effectively satisfy residual valence forces of the metal surface, but do not appreciably disturb the positions of metal atoms in the lattice. In other words, formation of a new lattice such as that of an oxide is not a necessary condition for this type of passivity. The decreased reaction tendency of the metal by reason of chemisorbed films can thereby account for low reaction rates of the stainless steels in many media, as well as a noble galvanic potential as is observed. Substances capable of adsorbing on the stainless steels, and hence accompanying the property of passivity, are typically oxygen, nitrites or chromates, but are not in any sense limited to these. Other elements and compounds can also chemisorb, and therefore may also play a major part in the mechanism of passivity in specific media. The mechanism of passivity based on chemisorption or activated adsorption begins with the interpretation Langmuir proposed for his experiments concerning adsorbed oxygen on tungsten.1 He found that adsorbed oxygen was tightly bound, remaining on the tungsten surface above temperatures at which WO3 rapidly volatilizes. The oxygen in such a state did not readily react with hydrogen even at

Jan 1, 1947

By Peter Hood

Data on worldwide geophysical activity in mining exploration programs is collected annually by the Geophysical Activity Committee of the Society of Exploration Geophysicists as part of a continuing service to the industry. The data is obtained by sending out questionnaires to all organizations (which are) known to be carrying out mining geophysical work; the organizations canvassed include mining companies, contractors, government departments and universities. The questionnaire is divided into three sections, namely ground methods, airborne methods and research. In 1968, 515 questionnaires were circulated throughout the non-Communist world and 283 replies were received which is a 55% return. A 67% return was received from the U. S. organizations surveyed so the statistics quoted in this report for the United States are reasonably reliable. This report is published in condensed form, but with emphasis on the United States statistics, with the permission of the Society of Exploration Geophysicists. It was presented at the 39th Annual International Meeting of the SEG in Calgary, Alberta, on September 15, 1969. Worldwide utilization of mining geophysical methods reached a new high in 1968 with total expenditures of United States $41.4 million, compared lo $32.3 million in 1967, representing a 28%, increase. The expenditure distribution by area and type of activity is shown in the graph on page 64. In terms of money spent, ground geophysical surveys accounted for 49% of the total, airborne survey's 36% and research 15%. The percentage of the money spent on ground geophysical surveys fell by approximately 7% from 1967, that for airborne surveys, increased by 5%, and for research the amount increased by 2%. Industry accounted for 79°1% of the total monies spent on mining geophysical activity in the world in 1968 and governments and universities 21 o%.

Jan 1, 1970

By C. Schlumberger, M. Schlumberger

In order to explore electrically a terrain composed of a succession of horizontal beds, a current of known intensity i is caused to flow between two grounds A and B, and the resultant drop of potential , caused by the resistance of the earth, is measured between two given points in the soil, M and N. In practice it is convenient to choose the two points M and N so that they lie on the line AB and their midpoint coincides with the middle 0, of that line, although this is not imperative. When the lengths L and I of the two lines AB and MN are varied, equations are obtained which may be solved for the resistivity p of the subsoil at various depths. Recall briefly that the formula 4 x l gives the average resistivity, in the horizontal direction, of a layer of earth which extends to a depth1 about equal to L/4. This elementary concept is adequate for numerous practical applications. Nevertheless, it must be said that, in many cases, a rigorous mathematical analysis may be made, provided it is always a question of homogeneous, superposed horizontal beds. The authors expect to publish, later on, appropriate methods of calculation for some specific cases.

Jan 1, 1932

By Arthur S. Dwight

THE professional career of Thomas Septimus Austin, who died at El Paso, Tex., August 23, 1906, was contemporaneous with the growth of the silver-lead smelting-industry of the Far West, to which his talents and zeal contributed in no small degree. Born at Stratford, Conn., December 7, 1853, he was the seventh son in a family of thirteen. His parents were well-to-do; and he received a thorough preliminary training at the Hopkins Grammar School, New Haven, Conn., passing thence to the Columbia School of Mines, in New York, where he was graduated in 1876. His first professional work was that of analytical chemist with a Cuban sugar company. In this position he spent a year, and, whatever else of benefit he may have acquired during that year in Cuba, he gained a facility of speech in the Spanish language which was of inestimable value in his subsequent work in Mexico and the southwestern United States. In 1877, he went to the Rocky Mountains, and, under the firm name of Murphy & Austin, opened an assay-office in Leadville, Colo., which was just then coming into public notice as a rich silver-lead camp. The next year, however, he entered the service of the Germania Smelting & Refining Co. at Salt Lake City, Utah, where he remained until 1882, first as assayer and chemist, and later as Assistant Superintendent. The Germanic bears the honorable distinction of being one of the first of the large " custom " lead-smelters erected in the West. Its founders may be called the pioneers of the modern lead-smelting practice, and the Germania served, to a large extent, as a model for the many plants that sprang into existence during the next few years in Utah, southern Idaho, Colorado and other lead-producing districts. The formulation, for the first

Jan 1, 1908

INTRODUCTION Porphyry copper deposits have been reported from the Caribbean area by Pease (1966), Cox, et al. (1973), Guild (1974), Kesler, et al. (1975), and others. This chapter summarizes the most widely known characteristics of those deposits. Only one deposit that conceivably can be classed as a porphyry copper occurrence is in production (Pueblo Viejo, Dominican Republic), but others are known whose tonnage and grade are of economic interest. Deposits in this province may be classified as copper-gold or copper-molybdenum types (Kesler, 1972), but deposits associated with quartz-rich plutons that have high Na2O:K2O and high gold:copper but low molybdenum: copper ratios dominate. Porphyry copper occurrences are reported in the literature from Puerto Rico, Haiti, the Dominican Republic, Jamaica, and Cuba. Only the porphyry copper deposits from Puerto Rico are extensively described in the literature; consequently the Caribbean porphyry copper province in general is not as well documented as the southern Cordilleran orogen. Because past published technical descriptions are incomplete, some data presented here are new to the literature. The Caribbean includes the island arcs between North and South America. Porphyry copper occurrences are known from the Greater Antilles, the generally east-west trending group of islands that lies south of North America. Fig. 48, therefore, only covers the Greater Antilles portion of the Caribbean. Porphyry copper deposits in this area are not described by the Lowell and Guilbert (1970) model in details of metallization (general paucity of molybdenum), alteration (scarcity of orthoclase), or petrography (preponderance of quartz diorite). Therefore, this model should be modified to include deposits associated with quartz-bearing plutons such as those found in the Caribbean. In the Meme deposit on Haiti ore occurs in skarn adjacent to the quartz diorite phase of a composite quartz monzonite-granodio-rite-quartz diorite pluton (Kesler, 1968). This deposit, with a K-Ar 66 m.y. date, is not included in Fig. 48 as a porphyry copper deposit because metallization is restricted largely to the intruded rocks. Although the intrusive rocks at the Meme deposit may contain sulfide near skarn contacts they are otherwise essentially unaltered. Porphyry molybdenum deposits as defined by Clarke (1972) have not been reported in the Caribbean area.

Jan 1, 1978

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By John W. Brauns, David H. Orr

9.1-1. Description and Basic Function. A conventional railroad haulage system for a surface mine performs the function of transporting the ore and/or waste out of the pit to a crushing plant or dump. Trains consisting of a locomotive and gondola or side-dump care suitable for loading by power shovels are used. Gondola cars are restricted to hauling ore as a rotary dumper is required to unload them. Side-dump cars are more versa- tile, being satisfactory for carrying both ore and waste; but because of their additional dumping mechanism they are likely to be more expensive to maintain (12). Also they weigh up to two times as much as a flat-bottom car of the same capacity, and, therefore, fewer cars can be hauled per train. Standard-gauge track is most commonly used. Track systems incorporate temporary track of low quality in areas where moves are frequent and permanent track of high quality on main lines. Rail haulage enabled open pit mining to establish its reputation, for efficiency. Prior to World War II it was the principal type of transportation used in large pits. Other successful surface mine haulage methods have been developed since that time. These have served to supplement railroad transportation, permitting selection of a method that is best adapted to the peculiar requirements of each mining project. 9.1-2. General Applicability and Controlling Physical Conditions. For handling rough rock, the shovel-train system is unexcelled (6). The ideal application is in a physically large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transported than will any other haulage method. Relatively gentle

Jan 1, 1968

By Klaus Schwerdtfeger, Hans-Jürgen Engell

Activities of silicon in Ni-Si melts have beelz determined in the temperature range 1480° to 1610°C from electromotive-force measurements involving the cells The data obtained are used to derive the activities of nickel and the integal free energies of mixing. Entropies of mixing are calculated from the free energies of mixing as obtained in the present study and the heats of mixing as available in the literature. ACTIVITIES in Fe-Si and Co-Si melts have been determined recently by the authors&apos; using galvanic cells consisting of alloy, an oxygen electrode, and an oxide melt as electrolyte. The present paper deals with activities in Ni-Si melts as measured with the same technique. A schematic diagram of the cell is shown in Fig. 1. The alloy and the electrolyte consisting of CaO and SiO2 are contained together in a silica-glass crucible. During the experiment the silica glass crystallizes to cristobalite on the surface of the crucible. Nickel contents of the electrolyte are very small (<0.1 pct as checked with chemical analysis), because of the noble character of nickel in comparison with silicon. A tapered silica tube is connected to the crucible through which a platinum or molybdenum wire is inserted, as shown in Fig. 1. A platinum tube reaches the surface of the CaO-SiO2 electrolyte from above. The platinum tube is provided with four holes on its side, through which oxygen of 1 atm pressure is blown over the electrolyte. The cell reaction is given by the equation Si(metal) + O2(gas) = SiO2(electrolyte) [3] and the galvanic electromotive force of the cell is given by the formula

Jan 1, 1965

By AIME AIME

ON May 5, the Washington, D. C., Section, A.I.M.E., devoted its meeting to the many-sided and perplexing question of mineral stock-piling for peace. Opening the symposium, Harry J. Wolf, of the War Production Board, outlined the problem under six heads: (1) Technical. Mechanical, chemical, or metallurgical importance of specified materials, emergencies that might arise, relative scarcity, and critical value of stock piles during emergencies. (2) Economic. Cost to Government, influence of Government stocks on commercial relationships and markets, effect of availability of items as a con¬structive influence on industry, Administration policies now and during postwar period. (3) Legislative. Need for immediate legislative action, need for legislation on postwar conditions as well as on current requirements, a constructive basic policy to prevent political manipulation. (4) Military. Consideration of re¬quirements and supplies bearing on national safety and needed for manufacture of equipment, and adequate reserves of scarce materials for research or experimentation by military agencies. (5) International. Interests of the United Nations in contradistinction to those of the United States; effects of nonisolation policy on nature, location, and administration of stock piles. (6) Negative stock-piling. Question of United Nations&apos; legislation to prevent stock-piling by Axis nations after the war and who shall purchase stock-pile materials and during what periods.

Jan 1, 1943