Search Documents

By G. Britsianes, T. L. Joseph

THE reduction of a lump of iron ore is a complicated sequence of up to three reactions proceeding simultaneously in a gas-solid system. As the ore moves down the blast furnace into zones of higher temperature and higher reducing power, it is successively reduced through the three oxides of iron into metallic iron. The reduction process involves much more than chemical problems. Physical factors add to the complexity of the overall process. Under optimum conditions, reduction of the ore is completed at a level about one-half way down the blast furnace stock column. At this point, the ore undergoing reduction has attained a temperature of about 1000°C and has been in the furnace for about 6 hr. On the practical side, the behavior of the ore during smelting has been of great interest to operators. Unsatisfactory blast furnace operation on burdens containing magnetite ore or badly slagged sinter has often been attributed to poor re-ducibility. The question of reducibility has also been raised in formulating quality standards for agglomerates such as nodules, briquettes, and pellets. In the present investigation, the solid phases formed during reduction were studied as a step toward a better understanding of the overall process. Equilibrium Studies The iron-oxygen equilibrium diagram shown in Fig. 1 reveal; a number of facts pertinent to the gaseous reduction of iron ores. This diagram is from the work of Darken and Gurryl, 2 and represents a correlation of the best available data. Four solid phases may exist during the complete reduction of hematite to metallic iron. These are hematite (Fe2O3), magnetite (Fe3O4), wustite (FeO), and iron (Fe). The wustite phase is a solid solution which is not stable below 570°C. At this temperature the solid solution undergoes a eutectoid-type of decomposition into the phases, magnetite and iron. Thus above 570°C, the diagram dictates that a hematitic ore should pass through a four-phase sequence on reduction to metallic iron. Below 570°C, only hematite, magnetite, and iron should appear. Information on the iron-oxygen system has been derived largely from CO and H2 reduction equilibria. The Fe-C-0 relationships have been studied extensively by R. Schenck and his coworkers and well summarized by H. Schenck.3 More recent studies have been made by Darken and Gurry.1, 2 Data from these sources have been combined and plotted in Fig. 2. With respect to the Fe-H-O system, the works of Emmett and Schultz4 seem the most reliable, and these data have also been included in Fig. 2. Certain physical properties of the solid phases of the iron-oxygen system are summarized in Table I. The crystallographic information is of special interest as much of the present work has been concerned with the X-ray analysis of the products of reduction. Reduction with Hydrogen The reduction of ore with hydrogen is the net result of two or more gas-solid reactions. Above 570°C, the reaction sequence may be represented by stoichiometric stages as follows: 3Fe203+ H2e2Fe,O, + H20 [1] 2Fe3O, + 2H2 6FeOw + 2H2O [2] 6FeOw + 6H3 ^ 6Fe + 6H=O [3] Fe2O3 + 3H2 ^ 2Fe + 3H,O. [4] These reduction reactions follow the general form: A (solid) + B (gas) e C (solid) + D (gas). This type of gas-solid reaction has been investigated by Langmuirl' who has shown that such reactions can occur only at the boundary between the two solid phases. Furthermore, a nucleus of the second phase must initiate the reaction. Once such an interface exists, the reaction proceeds through a layer of the solid reaction product (C). The specific mechanisms involved will depend a great deal on the properties and condition of this particular layer. A number of heterogeneous reactions such as the dehydration of single crystals of copper penta-hydrate and the calcination of limestone follow this type of process. It should be noted that the inter-facial type of reaction also occurs even in dense polycrystalline material which simulates a mono-crystalline behavior.

Jan 1, 1954

By R. L. Orr, J. D. G. Masse, Ralph Hultgren

The relative partial molar enthalpies of gold and tin in liquid Au-Sn alloys have been measured from Xsn = 0.474 to 0.510 at 696°K, slightly above the melting point of solid AuSn. Within an average precision of 6 cal per g-atom, the data are represented by two smooth curves, which satisfy the Gibbs-Duhem relationship and which do not show any anomalous behavior in the range of composition studied. The results give no support to the hypothesis that atomic associations in the equiatomic liquid alloy resemble those in solid AuSu. LITTLE has been firmly established as to the nature of atomic distribution in liquid metallic phases. A favored hypothesis assumes the existence of atomic groupings in the liquid phase which are similar to those in solid phases occurring at lower temperatures. Beginning with this hypothesis, it is often possible to adjust the values of certain parameters (such as degree of association) so that approximate agreement is achieved with certain features of the X-ray diffraction pattern of the liquid, even though many other possible structures might satisfy the data equally well. Thus, in this manner, the structure of liquid tin has been described as a dispersion of fragments of gray tin in a matrix of metallic tin.1 Four X-ray diffraction studies2"5 have been made of the liquid alloy of composition AuSn at temperatures slightly above the melting point of the solid. Each investigator concluded, on somewhat different grounds, that the liquid consisted to a large extent of arrays of atoms similar to the solid, with admixture of more disordered arrays. Solid AuSn has the nickel arsenide crystal structure: each tin atom has six nearest neighbors, all gold atoms; and each gold atom has six tin and two gold atoms as nearest neighbors. It remains highly ordered to the melting point. The liquid alloy has a large exothermic (?H700° K = -2700 cal per g-atom6) enthalpy of formation, favoring ordering and making the hypothetical molecular association not unreasonable. The possible existence of such solidlike arrays, or of a high degree of order that occurs preferentially at a specific composition in a liquid alloy, might also be revealed by thermodynamic behavior somewhat analogous to that in highly ordered solid alloy phases. The latter often exist over wide composition ranges, within which the highest degree of order occurs at the ideal composition for which the atomic fractions are equal to the fractions of sites which are "right" for each kind of atom. On departing from the ideal composition, the excess atoms occupy "wrong" positions, raising the internal energy and making it progressively easier for additional atoms to occupy "wrong" positions. Thus, on either side of the ideal composition, there should be a pronounced rise in the entropy and enthalpy, which would be shown particularly by the change in the relative partial molar enthalpies, ?Hi, since they depend strongly on d?H/dx. In the one case where accurate measurements have been made, the solid AuCu ordered phase, the structure becomes much less ordered as the composition deviates from the ideal, and relative partial molar enthalpies change sharply as shown by the data6 given in Table I. This suggests the possibility of finding similar pronounced changes in the relative partial molar enthalpies of gold and tin in liquid alloys near the composition AuSn if the postulated solidlike ar-

Jan 1, 1967

By Lucius W. Mayer

The iron-mines of the Ilsede Hütte Co. are at a town called Peine, about 20 miles east of the city of Hanover, on the railroad to Brunswick (Braunschweig). Hanover, the capital of the province, is a military city, of approximately 250,000 inhabitants, and Brunswick, 33 miles to the westward, has half this number. The mines here described are located in a hamlet called Bülten. The Ilsede Hütte Co. operates two mines, 1.5 miles apart, in this district, Gruber Bülten Adenstadt and Gruber Lengede Bodenstadt. It also operates an iron-mine north of Hanover, known as Eiserhaven, and one in the Harz mountains, the Georg Friedrich, at Grauhof. At Bülten a coarse conglomerate, a, Figs. 1 and 2, contains nodules of limonite, cemented together by calcium phosphate. The ore contains Fe, 25 to 45; Mn, 3 to 4; P, 0.6 to 1.4; S, 0.02 to 0.09; and CaCO3, 40 per cent. Directly above the conglomerate is limestone, b, followed by a mixture of clay and sand, c. Below the conglomerate is a hard clay floor, d. The ore-body, from 10 to, 12 km. long, and from 3 to 4 km. wide, has a maximum thickness of 20 m. It clips approximately 10° S.E., and strikes N. 45° E. Diamond-drill prospecting shows that the thickness diminishes to 1 m. as the end of the deposit is approached to the northward. At this point the deposit is 250 m. below the surface. In Fig. 2, the arrow, A, indicates the general direction of the work along the face, a, which is carried forward in a straight line for its entire length. At B, a train is approaching, which has come from the bench-track, shown at G, by a circuitous route, and is dumping the overburden behind the face, in the space left by the excavated rock. Formerly the work at this mine was essentially open-cut, the deposit having a very strong outcrop. Figs. 1 and 2 show also

Sep 1, 1908

By Jackson M. Langton

Substantial evidence supports the theory that high-angle faults and overthrusts in the Morenci-Metcalf region were initially caused by a Late Precambrian-Early Paleozoic stress field. These faults were reactivated in Late Paleozoic-Early Mesozoic time which completed the structural framework prior to the Laramide Orogeny. Excluding an interruption by diabase dikes and sills, Paleocene-Eocene magmas invaded the pre-existing structures and became progressively more sialic in composition and nearer to the surface with each subsequent injection. The last sialic intrusion was highly explosive, rendering the country rocks more permeable for hypogene and supergene activity. Widespread dilation, instigated by uplift and subsequent magma intrusion, caused extension to the northwest and southeast. A major locus of hypo gene alteration and mineralization appears to be centered around the south and southeast periphery of the youngest granite porphyry stock. A potassic, sulfide-deficient core is telescoped by a pyritic, phyllic zone which in turn is enveloped by widespread propylitic alteration.

Jan 1, 1974

By Wilson Blake

A mathematical model based on the finite element method of stress analysis has been used to describe the behavior of the western wall of the Kimbley Pit as its slope was steepened from 45° to 57°. Theoretical stress changes because of slope modification are slight except at the toe of the modified slope. Magnitudes of stress created are small when compared with the strength of a competent rock. Resulting displacement patterns point out the need for determining the in-situ state of stress at a site prior to excavation or modification. A comparison of model results with field measurements shows that, in general, the model has described the measured behavior of the west wall of the Kimbley Pit remarkably well. The Bureau of Mines and the Kennecott Copper Corp. began joint research on open-pit slope stability at the Kimbley Pit, Ely, Nev., in 1961. The initial or planning phase of this research dealt with a detailed geologic study of the Kimbley Pit, determination of in-situ stresses in the district, laboratory and field tests to determine rock properties, and the design of a full-scale experiment to study the behavior of this pit as its western wall was steepened from 45° to 57°. Fig. 1 shows a cross-section of the original pit outline, the steepened pit outline, major geologic features, and the two instrumentation adits. After the final or slope modification phase of the research began, a laboratory research program was initiated to develop a mathematical model that would analytically describe the behavior of the pit as its western slope was steepened. This theoretical model study of the slope modification at the Kimbley Pit was conducted with the finite element method of stress analysis. The results are described in this report.

Jan 1, 1969

By Edward Steidle

NOTHING stands still. We go forward or backward. As a distinct group of educators, our immediate concern is with the preparation of young men and women for participation in the mineral industries on a professional basis. I am going to have the temerity to state emphatically that for a long time as a whole we have remained in a static position. We are now confronted with the choice of advancement or retrogression. We are still in a position to make a choice and our ultimate fate will depend upon the course of action we elect to follow. Wars always have been great catalysts and social and scientific advancements mature under military stimulus in a fraction of the time normally consumed. We are now in the midst of a conflict whose duration or final effects cannot be estimated. However, the record already demonstrates that this war as never before is a mineral war in which incentive, strategy, and outcome are directly related to the distribution and utilization of minerals. The inevitable result is a drain upon our resources now reflected in our record production and a growing public consciousness of the importance of minerals in the role of human affairs. It is evident that we must seek new mineral frontiers beyond the borders of the United States and take every other precaution to forestall a "have-not" position in the world.

Jan 1, 1943

By Homer N. Mead

This report develops equations for decline curve analysis based upon the premise that the rate of change of the reciprocal of decline for succeeding time intervals is constant when the reservoir is produced under a fixed set of conditions. A method is shown for predicting maximum production rate against cumulative production for any reservoir. A method is also presented for predicting future production rate by an analysis of past production performance after decline has been esrahlished. INTRODUCTION No significant contribution to the analysis of decline curves by the loss-ratio method has been made since J. J. Arps paper1. The concept of loss-ratio that was developed by Arps and his contemporaries has been redefined in another way and the concept of instantaneous loss-ratio at time zero has been added. In the mathematical developmerit by Arps, production rate was related as a continuous function with time and his equatlons were developed on that basis. In this paper, production is considered to be a series of segments for equal time intervals and equations have been developed based upon these finite differences. It is realized that decline curve analysis is not the answer to all predictions of reservoir behavior. However, as production must decline from an initial maximum rate to zero in any reservoir, if such decline can be expressed as an infinite series, this series should accurately predict production. Decline curve analysis should be considered a valuable tool that may be used in conjunction with predictions of future recoveries by other methods. Various uses of the decline curve method will be discussed in this paper. Equations predicting production rate at any time and cumulative production by exponential and hyperbolic decline will be developed. Characteristic values of b related to various types of drive will be discussed. After that a hypothetical reservoir will be studied and ultimate recovery by natural depletion and pressure maintenance compared, then actual field examples will be shown and discussed. The rate-cumulative curve introduced by H. N. Marshs in 1928 is an important one for use in estimating future production rate and ultimate recovery. This graphical method is the one that is used in conjunction with the equations to be developed for predicting production behavior. EXPONENTIAL DECLINE In exponential decline each succeeding production rate per unit of time is a constant percentage of the production rate just before it. Since (1 — r) is the common ratio, where r is the constant decline rate, this condition may be expressed as a geometrical progression; thus Pn = P (1 - r)n-1 . ......(1) Where r is less than unity, r Since P1 (1 - r)n = Pn+1 P1 - Pn+1 C =P1-Pn+1/r........(2) LOSS-RATIO In this paper the calculation for loss-ratio has been changed from the method presented by Johnson and Bollens2. The first loss-ratio to be calculated is a,; it is the initial production per unit of time after decline has set in divided by the difference between the initial and the second production rate. This loss-ratio is for the first time interval. After b (which is the constant change

Jan 1, 1957

By M. H. Waxman, M. Gondouin, H. J. Hill

Streaming-potential experiments were conducted within the Muddy- and Dakota-sandstone interval of a Denver basin well. Analysis of the data shows that, for this case, streaming potentials opposite sands were higher than those opposite shales when the mud was fresh. Streaming potentials opposite shales, however, were of sufficient magniiIlde to be important in SP interpretation. They were linearly dependent upon pressure differential, and they increased with mud filtrate resistivity. The magnitude of streaming potentials opposite sands was influenced by the characteristics of the original mud cake formed at the time of drilling. Use of mud samples taken at the time of logging may not always be satisfactory for determining streaming-potential corrections. Both the streaming and electrochemical potentials were found to be affected by the previous history of the borehole system. Following a change in mud characteristics, several days were required for SP stabilization. This was, in part, due to the mud cake acting as an imperfect shale membrane. INTRODUCTION Laboratory investigations by Wyllie,1 Salisch,2 Moore," Sen Gupta and Bannerjee,0 and Hill and Anderson' have shown that streaming potentials developed across mud cakes deposited on permeable filter beds are of sufficient magnitude to be critically important in SP interpretation. Streaming potentials across shales have been reported by Schenck,' Gondouin and Scala; and Hill and Anderson." The magnitude of the shale streaming potentials obtained by Schenck and by Gondouin et a1 led these authors to conclude that in many cases the shale streaming potential would approximately equal the mud-cake streaming potential. Hill and Anderson, however, obtained somewhat lower magnitudes of shale streaming potential. The field experiment described in the present paper was a cooperative project carried out by the respective operations and research departments of Schlumberger Well Surveying Corp., Shell Development Co. and Shell Oil Co. The primary objective of the experiment was to determine in the borehole the streaming-potential behavior of both shales and mud cakes under conditions approaching, as nearly as possible, those normally encountered in logging practice. METHODS AND EQUIPMENT WELL A Muddy- and Dakota-sandstone vie11 in the Denver basin was chosen for the experiment. Both sandstones were water-bearing and, since reservoir pressures in these sandstones are abnormally low (gradient of approximately 0.25 psi/ft), it was expected that studies of streaming potential could be conducted from low-pressure differentials (approximately 200 psi) to about 27000 psi by bailing mud from the hole, filling up and then applying wellhead pressure. The selected well encountered the Muddy sand-

By AIME AIME

THE 1941 fall meeting of the Iron and Steel and the Institute- of Metal, Division held at the Ritz-Carlton Hotel, Philadelphia, during the first three days (Oct. 20-22) of the National Metal Congress was well attended as usual, and the seven technical sessions and the joint round table on order-disorder transformations were this year of considerably more than routine interest. Despite unseasonably warm weather, a scarcity of hotels (there were rumors, apparently well-founded, that , some of the metal man attending the Congress had to stay in tourist camp), and a multiplicity of technical and other ions of the co-operating societies that gave the Congress this year the general air of a three-ring circus the A.I.M.E. sessions attracted audiences that ragged from seventy or eighty up to 350

Jan 1, 1941

By S. C. Sircar, B. K. Dhindaw

KINETICS and mechanism of sulfation reactions have been studied extensively. Qualitative and quantitative data are reported for the kinetics and mechanism of sulfation reaction of copper oxide pellets;''2 yet it remains a controversial Subject. The mechanism and kinetics of the sulfation of zinc oxide powder (B.D.H. analar quality) were studied by gravimetric technique. A spring of high-carbon steel wire with accuracy well within 0.2 mg was used for measuring weight change. The sample was taken in a Pyrex glass bucket, hanging freely inside a Pyrex glass tube reactor, with a gold wire attached to the spring, the reactor being surrounded by a movable furnace (double wound type) with a temperature control within *5"C. Flow of oxygen, 60 cu cm per min, and sulfur dioxide, 45 cu cm per min, were measured through calibrated flowmeters and the mixture dried over PZ05 before entering the reactor. The experimental results are presented in Figs. 1 and 2. The plot of weight change of zinc oxide, giving the amount of zinc sulfate formed, was found to be linear over the temperature range of 500" to 700° C and up to a conversion of approximately 60 pct, as beyond it they divert from linearity.' The rate of sulfation was found to be affected by total flow rate of gases at a fixed ratio of SO2/O2, up to 60 cu cm per min, and was found to be linearly dependent on quantity of total powdered sample taken. The plot of rate of sulfation of zinc oxide, 70 mg, with varying amounts of vanadium pentoxide, at a constant ratio of gases as mentioned above, and at a constant temperature of 625"C, was also found to be linear as seen in Fig. 2. Extrapolation to zero V2O5 addition gives the same rate of sulfation, as in case of pure zinc oxide, 70 mg. Vz05 was prepared by heating ammonium vanadate at 600°C for 15 min in a muffle furnace. The available literature points out that the theory of sulfation that has received the maximum support postulates the following mechanism for sulfation of ZnS: 2ZnS + 30, = 2Zn0 + 2SOZ; the ZnO formed acts as a catalyst for the reaction, 2 S02 + O2 = 2S03. This SO3 reacts with ZnO to give zinc sulfate. It is suggested here that the above widely supported mechanism is operative in the sulfation reaction and that the rate-controlling step in the sulfation reaction of ZnO is the formation of SO3 from SO, and 0,. The authors are carrying on further work in this line, and the details will be published later. The authors wish to acknowledge the facilities provided and the help extended by Prof. P. R. Dhar, Head, Department of Metallurgical Engineering, and the permission granted to publish this note by the Director, I. I. T., Kharagpur.

Jan 1, 1969

By J. L. SILSBEE

THE existence of large saline deposits in that flat arid basin, known as the Great Salt Lake Desert, has long been recognized, but the extent and great commercial value of these deposits has not been generally appreciated. That a very considerable interest has recently developed is indicated by the fact that about 263 prospecting permits-each covering about 2560 acres of land in this Desert-have been issued under the Potash Leasing Act (Act of 0ct. 2, 1917-40 Stat. 297), and patents granted on approximately 40,000 acres. It is reported that patents and leases have, or will be applied for on an additional 80,000 acres in the basin. , Tests have been made on probably less than 10 per cent. of the total area of the basin, but these have proved a practically unlimited supply of brine available -sufficient, probably, to. furnish the potassium and magnesium chloride requirements of this country for at least a hundred years.

Jan 1, 1925

By Leon W. Dupuy

Many articles have been written describing peculiar and particular types of drilling. Little correlation has been made between the character of ground to be drilled and sampled and the type of drilling most desirable for procuring satisfactory samples. In development work, the engineer and metallurgist often desire the recovery of a sample in as physically natural a condition as possible, particularly when the sample must provide material for process tests as well as chemical and physical analyses. This paper describes the results of experimentation in drilling unconsolidated materials carrying titanium minerals in the Magnet Cove area, Ark. The drilling was most difficult in that the ground varied much in consistency, and it was vitally necessary to recover a physically natural sample. Ordinary churn drilling recovered a sample that could be analyzed chemically, but the sample was not in its natural state. The problem was successfully solved by utilizing and further developing methods used in the oil and clay industries.

Jan 1, 1949

PORPHYRY mining in the Bisbee district in Arizona did not begin until 1923, though Bisbee had been the scene of profitable copper-mining operations since 1880, and during the interval had contributed roughly 2,000,000,000 lb. of copper to the world's supply. At that time it ranked third among the copper districts of the United States, first place for total production going to Butte, Montana, and second to the district centering around Calumet, Michigan. Bisbee's production had come from the so-called "limestone" mines operated principally by the Phelps Dodge Corporation and the Calumet & Arizona Mining Co. Each of these companies had a large smelting plant at Douglas, 25 miles southeast of Bisbee on the Mexican border. The town of Douglas owed its existence primarily to the copper mines of Bisbee, the particular location having been determined, first, by the fact that water in adequate supply could be obtained by sinking wells; and, second, by its position about equally distant from Bisbee and the mines in Sonora, Mexico, of the Moctezuma Copper Co., a Phelps Dodge subsidiary. Three partners, Martin, Reilly, and Ballard, conducted the first operations of consequence at Bisbee about 1880; and in 1881 a smelting plant consisting of two 36 in. water-jacketed blast furnaces was erected near by. The ore came from open-cut workings on the later-to-be-famous Queen orebody. The furnace charge is said to have averaged 23 per cent copper-twice as rich as the concentrates from the mills and four times as rich as the smelting ore shipped from Bisbee in recent years. As early as 1881, disputes arose among owners of various claims, and groups of claims, over the ownership of orebodies under the law of apex and extra-lateral rights. This law gives a miner the right to follow his vein downward on its dip, even

Jan 1, 1933

By A. H. Larson, T. P. McNulty

RECENTLY, an investigation of the absorption of sulfur dioxide gas in molten binary copper alloys was conducted. A Sieverts-type apparatus, consisting of a mercury-filled gas dispensing buret and a mercury manometer, was used initially for determining the volume of gas absorbed as a function of pressure. The equilibration behavior of the alloys studied indicated that the mercury in the gas measuring system was absorbing sulfur dioxide. Owing to the widespread use of mercury as a displacement medium in absorption studies, an investigation was made to determine the nature and magnitude of the mercury - sulfur dioxide absorption effect. The gas measuring system was modified by substituting a Worden Quartz Products Type PDHV fused-quartz-spiral pressure gage for the mercury-filled dispenser and manometer. The dispensed gas volume at known temperature and atmospheric pressure was measured by evacuating a Pyrex vessel of known volume and by admitting sulfur dioxide into the vessel until the attached quartz pressure gage registered atmospheric pressure. Atmospheric pressure was measured concurrently with a separate mercury barometer. The volume of the empty sample chamber and its attendant apparatus was determined by measuring the equilibrium pressure accompanying the addition of a measured volume of sulfur dioxide into the initially evacuated system. The volume of the mercury sample was calculated from the density of mercury at the temperature of the study (25°C). Measured volumes of sulfur dioxide were then dispensed into the system and the equilibrium pressure accompanying each gas addition was determined. From the difference between the system volume and the mercury volume, the number of moles of gaseous sulfur dioxide remaining in the system at each pressure was calculated. The difference between the number of moles of gas dispensed into the system, denoted Enso2: and the number of moles of gas remaining in the system after absorption equilibrium had been attained, denoted nso2(g), was equal to the number of moles of absorbed gas, denoted nSO2. The number of moles of absorbed gas was then converted to absorbed volume, denoted VSo2, in cu cm at stp conditions of (PC and 760 mm Hg. Table I contains calculated values of Snso2, nSo2(g), and VSo2 for different sulfur dioxide pressures. In the original system, denoted Run I, volume limitations of the gas dispensing system prevented absorption studies at equilibrium pressures near atmospheric pressure, so a different gas dispensing system, denoted Run 11, was used for determining the last pressure reading in Table I. The data in Table I are expressed in terms of the absorption of sulfur dioxide in 49.68 cu cm of mercury. In Fig. 1, these data are expressed in terms of the absorption of sulfur dioxide in 100 cu cm of mercury. Since the absorption data plotted in Fig. 1 show a linear relationship, the volume of sulfur dioxide absorbed in mercury is a function of the first power of pressure. The absorption reaction is So2(gas) = SO2 (in Hg) The first-power pressure dependence, coupled with the fact that the sulfur dioxide could be removed from the mercury by applying vacuum, indicated reversible

Jan 1, 1967

By Henry F. Hebley

This paper brings within the compass of one comparatively brief article a general description of the situation concerning the nation's water resources. It touches upon the phenomenal growth in the demand for water supply and emphasizes the problems facing the coal industry both with regard to acid mine water drainage discharged from active and abandoned mines and the suspended solids discharged to the stream system from wet coal preparation plants.

Jan 4, 1953

By James P. Kimball

Jan 1, 1885

By G. B. Kasik, George Sachs, George Espey

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually has been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,1 the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin" and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between [ ]

Jan 1, 1941

By M. C. Leverett

THE dynamic behavior of a multiple fluid system is completely describable in terms of driving forces and resistances to flow. The latter are proportional to the vis-cosity of the fluid under consideration and inversely proportional to a property of the system termed the " effective permeability" to that fluid, a property therefore defined by this relation. Since three phases are usually present in oil reservoirs, it is essential to know the effective permeabilities to the several fluid phases, and the relationship between the composition of the fluid in the pore space and that of the flowing stream, in order to handle satisfactorily certain problems of oil production. In this regard, there are many unknown factors and parameters, and many that can be evaluated only indi-rectly. However, it is expected that work along lines similar to this present under-taking will help materially in solving these problems. Previous workers in this field have inves-tigated the two-phase systems, water-gas,1 water-oil2 in unconsolidated sands, and water-gas3 in consolidated sands. The ex-tension of the study of the flow of hetero-geneous fluid systems from two to three phases involved only slight changes in technique. The apparatus used in the present work, except for slight changes to be described, was that used by Leverett in his water-oil experiments.2 Correlation and interpretation of data were made by methods analogous to those used in two-phase work. The relative permeability to a phase-the effective permeability divided by the permeability of the system to a homogeneous fluid-was employed through-out in correlating the rate of flow of that phase with the composition of the pore space. Quantitative measurements of two inde-pendent physical properties of the system were required to determine the composition of the pore space. As in the two-phase work, the fraction of water was determined electrically. The gas fraction was deter-mined by measuring changes in volume accompanying measured pressure changes. Suitable account was taken of the solubility of the gas in the liquid phases, and of the vapor pressure of the water phase. Since this work was exploratory in nature, no attempt was made to obtain highly accu-rate numerical results. Reasonable precision and reproducibility were sought.

Jan 1, 1940

By A. P. Miller, T. S. Washburn

Improved procedure in the manufacture of rail steel has come as the rail user demanded better wearing qualities combined with greater unit weight. With each weight increase per lineal yard has come greater difficulty in making a product that would successfully withstand all tests that modern rails must meet. With these facts in mind, and with a sincere desire to produce a rail whose service in track would be satisfactory in all respects, the steelmaker was quick to realize that all of the factors entering into his process would have to be more closely controlled. Control of rail-steel slags was recognized as one of the most important of many interdepending factors. The object of slag control is to hold the slag compositions within a range that gives the best results with respect to economy of production, uniformity of analysis, and quality of the finished rails. The most important component of the slag from the standpoint of these production and quality factors is the ferrous oxide content. This component is a good indicator of the basicity and oxidizing power of the slag, and these largely govern the effect of the slag on the steel. Consequently, the

Jan 1, 1935

By A. P. Miller, T. S. Washburn

Improved procedure in the manufacture of rail steel has come as the rail user demanded better wearing qualities combined with greater unit weight. With each weight increase per lineal yard has come greater difficulty in making a product that would successfully withstand all tests that modern rails must meet. With these facts in mind, and with a sincere desire to produce a rail whose service in track would be satisfactory in all respects, the steelmaker was quick to realize that all of the factors entering into his process would have to be more closely controlled. Control of rail-steel slags was recognized as one of the most important of many interdepending factors. The object of slag control is to hold the slag compositions within a range that gives the best results with respect to economy of production, uniformity of analysis, and quality of the finished rails. The most important component of the slag from the standpoint of these production and quality factors is the ferrous oxide content. This component is a good indicator of the basicity and oxidizing power of the slag, and these largely govern the effect of the slag on the steel. Consequently, the

Jan 1, 1935