Search Documents

By C.H. Lorig, M.C. Udy

Through the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the genera1 effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. Literature Two general factors should be considered in a study of reduction of iron oxide: (I) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe304-FeO-H2-H2O, Fe3O4-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnasl published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at One temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1943

By M. C. Udy, C. H. Lorig

Through the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the genera1 effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. Literature Two general factors should be considered in a study of reduction of iron oxide: (I) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe304-FeO-H2-H2O, Fe3O4-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnasl published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at One temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1943

By BLAllEY STEVENS

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. TEH object of this paper is to show how igneous intrusion is governed by definite mechanical laws. A distinction is made between dikes and fissures, and the various characteristics of intrusions are explained on an exact scientific basis. The modification of rock-stresses by intrusion is then considered and extensive isostress regions are recognized. Finally, a complete classification of intrusions is constructed covering all pos-sible cases. The generalizations of observed data, taken from Geikie's Textbook of Geology, conform to the laws of intrusion herein stated, and the deductions based upon these laws. No authority, however, is quoted for the type which I have named a corrugated intrusion. Its existence is a necessary deduction from the laws of intrusion, and even the entire absence of examples in technical publications cannot disprove its reality. In all probability, corrugated fissures would have remained undiscovered, but for the working of mineral veins. As intrusions of tabular form are seldom worked for commercial purposes, it has been left for theory to anticipate the discovery of corrugated dikes. In the light of these laws of intrusion and the corresponding laws of fissures,1 there seems to be a remarkable uniformity of stress-distribution in rocks at moderate depths. This renders .possible the mathematical calculation which should help us to approximate exact science in this and kindred branches of applied geology.

Jan 1, 1911

By William J. McCaughey, Richard L. Barrett

FOR sixty years-in fact, ever since the inception of the basic steelmaking process -basic slags have been the subject of study by chemists, metallurgists and petrographers, with the purpose of providing a better understanding of the reactions between the slag and the metal during the refining process. The result of this work and of the researches of mineralogists and physical chemists into the chemistry of oxide systems is a considerable body of literature dealing not only with slags themselves but with equilibrium relationships in systems synthesized from pure components. Since any actual slag is a multicomponent system more complex than any yet worked out in the laboratory, a complete solution to the problem is still far away. The writers have recently published a paper1 which they believe sheds light on the role of the slag in the elimination of phosphorus and it is the purpose of the present paper to discuss the metallurgical applications of that work. Since the pioneer investigations on the constitution of basic slags carried on by Stead and Risdale, Carnot and Richards, Hilgenstock and others in the 1880's, a considerable body of literature on this subject has appeared. Many of the more important of these papers were summarized in the previous paper,' therefore they will not be reviewed here. PETROGRAPHIC STUDY The present writers have had occasion, over a period of years, to examine petrographically a great number of basic steel- making slags having a very wide range of chemical compositions and made under various conditions of operating practice. Although certain of these slags exhibit some unusual features, it is a remarkable fact that the great majority of mature slags show certain typical characteristics, which persist throughout the wide range of chemical compositions. The typical mature slag usually appears under the microscope to consist of two phases. The phase of primary crystallization is light colored and doubly refracting. If separated mechanically and subjected to chemical analysis, it is found to consist essentially of SiO2, CaO, and P2O5. Sometimes, although not usually, two such silicate-phosphate phases are found. The other conspicuous phase is dark in color and optically isotropic, and occurs as the interstitial material between the grains of the light colored phase. This dark colored interstitial phase when analyzed is found to consist essentially of FeO,Fe2O3, MnO, and MgO. In some slags high in iron oxide, particularly those from low-carbon heats, dicalcium ferrite is found. This phase is dark reddish brown in color and anisotropic.

Jan 1, 1944

By Hertha R. Freche

The diffusion of magnesium and silicon from the core into the high-purity coating of Alclad sheet is important commercially, and led to the use of a duplex product for the study of diffusion by means of spectro-graphic analysis of successive layers. It has been found that in the duplex materials the diffusion of magncsium from an undersaturated aluminum-magnesium alloy into its high-purity aluminum coating is approximately of the same order of magnitude as the diffusion of silicon from a saturated aluminum-silicon alloy into its high-purity aluminum coating. However, if magnesium and silicon are both present in the alloy in the ratio of Mg2Si, they appear to diffuse in the approximate ratio of this compound. Finally, if the alloy contains silicon in excess of the amount required by magnesium silicide, the amount of diffused silicon in the high-purity aluminum coating will also be in excess. The interdiffusion of metals in the solid state is of both scientific and technical interest, because it is helpful in the study of the alloy structure and in the solution of problems pertaining to the strength and surface condition of the fabricated product. W. C. Roberts-Austenlt carried out the first quantitative determination of the coefficient of diffusion of gold into lead. This classical experiment was followed by a series of investigations on the diffusion of metals and nonmetals in iron and steel and in nonferrous metals and alloys. Recently the diffusion of copper in coated strong aluminum alloys was investigated by A. Burkhardt2. This appeared to be the first published investigation on the diffusion of metals into aluminum. The present investigation was the direct result of a technical question in connection with alloy fabrication and is a summary of some preliminary work pertaining to the diffusion of magnesium and silicon into aluminum. The results necessarily will be subject to some variations, since this is the first attempt to evaluate the coefficients of diffusion of magnesium and silicon into aluminum according to this method of procedure. This

Jan 1, 1936

By Simon D. Strauss

The world appetite for minerals in the, third quarter of this century grew at a higher rate than had been anticipated. To illustrate, consider the experience of four, commodities. Excluding the Communist bloc, sometimes referred to as the centrally planned economies, demand for aluminum increased at a compound rate of 8.6% between 1950 and 1975,; copper rose by 4.4%; iron ore by 5.5%; and tin, the laggard in the group, by 2%. Except for tin, the figures are substantially greater than growth rates anticipated in 1950 in the Paley Commission report and other studies. The growth rate was not evenly distributed in geographical areas. Professor Wilfred Malenbaum of the University of Pennsylvania did an interesting study breaking these figures down as among three principal sources of demand -- the United States, other industrialized nations (which he referred to as the "rich lands"), and the developing world (which he referred to as the "poor lands").

Jan 1, 1982

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Charles H. Fulton

ONE of the events of note in mineral industry education circles during the year was the summer school for engineering teachers, devoted to mining and metallurgical engineering, which was conducted by the Society for the Promotion of Engineering Education in co¬operation with the University of Wisconsin. It was in charge of Prof. Harry P. Hammond, director of the summer school, and Prof. Richard S. McCaffery of the University of Wisconsin. It was attended by 63 people, and practically every educational institution offering mineral industry courses had representatives present. The session was successful and those in attendance spoke highly of the pro¬gram and results obtained. The Mineral Industry Education Division cooperated with the S.P.E.E. in this project. Prof. Hammond will discuss the purpose and results of this session at the February meeting.

Jan 1, 1934

By Michel David

One of the most important questions that arises in ore estimation can be stated as follows: What is the error when one extends the grade of a sample to a certain volume? The theory of regionalized variables, with the concept of extension variance, provides a response to that crucial question for any kind of sample extended to any volume. For the usual "extensions" encountered in current mining practice, some simple results can be derived from that theory which was initiated by Dr. G. Matheron. These results have been applied to a stratiform lead-zinc deposit for which several estimations of grade, tonnage and related precision have been made for a series of grid sizes such as might be used in a progressive exploration program.

Jan 1, 1969

By Arthur Lubinski, K. A. Blenkarn

It is explained why the bottom portion of freely suspended tubing in a pumping well buckles and straightens in succession during the pumping cycle. Field evidence of resulting rod-on-tubing wear, excessive polished rod load, and excessive horsepower are given. The possibility that buckling hastens pump wear is strongly suggested. Means for either prevention of buckling or for mini-mizing its effects are explained, their relative merits compared, and field results of their use given. These means are: tension anchors, tail pipe, sucker rod guides, and corrosion inhibitors. Charts and formulas for best use of tension anchors, tail pipe, and guides are given. Use of tension anchors, or compression anchors with a heavy tail pipe, prevents both buckling and breathing, thus improving volumetric efficiency. Without tail pipe, buckling above compression anchors precludes such improvement. INTRODUCTION It is well known that a column must be subjected to some compression in order to buckle; and also that a structural member does not buckle if subjected to a tension. When consideration is given to a tubular column, the question may be asked, "How is the buckling phenomenon affected by inside or outside pressure?' At first, it seemingly should not be affected. However, this is not so. In order to arrive at a correct deduction one should first understand the basic reasons for buckling of a column under loading*. Then he should add to the effect of that loading the effect of pressure. Following this procedure, one may discover quite unexpected phenomena. In some cases, when subjected to more pressure inside than outside, a pipe may buckle under tension. In other cases, a pipe may remain straight, although subjected to a very large compression. In 1950 and 1951 it was explained why the bottom portion of a string of pipe freely suspended in a well does not buckle even when subjected to a large compression due to buoy- ancy.2,3 It was shown that the com-monly used concept of a neutral point, as being a point in the string with neither compression nor tension, is inadequate, and a more relevant definition of the neutral point was introduced. The findings were also generalized to cases of different pressures inside and outside a pipe.3a Later, in a further generalization, allowance was made for variations of stress and pressure with depth.' The findings were applied to the new technique of hydrostatic high pressure testing of lengths of pipe in the mill.5 In 1952 it was observed that previous theoretical findings apply to tubing in pumping wells. The lower part of freely suspended tubing buckles during the upstroke portion of the pumping cycle. Later, it was ascertained that this phenomenon is responsible for wear and malfunctioning of the equipment. Various remedial measures were devised and successful field trials conducted. Only brief mentions on the subject have been published.6,7 In this paper, the phenomenon of tubing buckling is explained, field

Jan 1, 1958

By L. W. Rowe, W. R. Opie

A brief history of TiCI, production and purification is given. Chlorinator feed materials for the production of TiCI4 are classified. The thermodynamics and kinetics of Ticl4 production by chlorination of TiO2 are discussed. Problems encountered in the chlorination and purification steps are outlined in detail. MOST of the current processes for the production of titanium metal require the use of TiC14 as a source of titanium values. This material can only be produced by a dry chlorination process, since it is immediately hydrolyzed in the presence of water. When pure, the tetrachloride is a colorless liquid boiling at 136°C. It fumes readily in moist air, reacting immediately with the moisture to form TiO, and HC1. History The tetrachloride was prepared as early as 1826 by DumasL who chlorinated a red hot mixture of carbon and TiO,. Since then, numerous other mixtures have been used including rutile, ilmenite, beneficiated ilmenites, titanium pigment, slags, and the various titanium metalloids such as TiN, TiCN, TiOC, and TiS2. S2Cl2, phosgene, and CC14 have been substituted for chlorine and CO has been used in place of carbon.

Jan 1, 1956

By S. A. TAYLOR

AN EDITORIAL on the Strike Situation in the Coal mining industry in the New York Evening Post of Nov. 4, 1919, gave what purported to be statistics of the Department of Labor, for a period of two weeks, which showed an average for the year, based on these two weeks, of 32% hours per week. This mode of arriving at the number of hours per week, while not accurate, is not so far off from the facts as to call for any special comment. The report of the U. S. Geological Survey, Department of Coal Statistics, give so the number of days worked in 1917 as 243; reducing the same to hours per week, assuming 8 hours per day, shows a weekly operation of mines at an average of 36J4 hours. But this assumption is not exactly correct, for the reason that it is not very often that the miners work the full 8 hours per day. There are many explanations for this, but it is not pertinent to this statement to discuss them now, as the important thing to consider is whether a 30-hour week would be for the best interest of not only the men themselves, but the public or country in general.

Jan 1, 1920

By Y. C. Kim, I. K. Chopra, F. Martino

This paper reviews geostatistical work in a coal deposit performed jointly by the University of Arizona and the Homer City Owners. The study objective was to Predict more accurately the inseam sulfur values of the deposit for the purpose of future emission control. Based on initially available 112 DDH information, variogram models were developed for sulfur, ash, and thickness for the entire deposit. The deposit was then kriged using 333 m x 333 m panel size. Kriging produced better results than conventional isopachs. The estimation variance information obtainable from geostatistics was then used to improve development drilling activities that were underway. This effort was successful. Up-to-date experience on the use of conditional simulation of the deposit appears promising for future emission control strategy development

Jan 1, 1982

By Leonard Grimshaw

THE idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a com-posite steel.

Jan 1, 1936

By GLENVILTE A. COLLINS

(Presented at a Meeting of the Spokane Local Section of the Institute, Feb. 17, 1912, and accepted for publication in the Bulletin. ) WHILE I am not at the present time engaged in active mine-management, my duties permit of extensive study and examination of many mines, mills, and reduction-works in various places throughout the United States. Being much interested in efficiency-work in general, and an ardent reader of writings on this subject by Frederick W. Taylor and others, as applied to manufacturing-plants, and having served my apprenticeship from mucking to the engineering design of ore-dressing and underground plants, I hope that this paper will lead others to investigate the field more fully, to the improvement of general mine- and mill-operations, as well as the advancement, intellectually, physically, and financially, of the employee and his relations with the employer. If a man who is prepared to look closely and observe broadly starts in Canada and zig-zags from camp to camp to southern Mexico, taking time casually to inspect mines, mills, and smelters, he will be pitifully impressed by the great difference in customs, and the general waste of labor, time, and money throughout the country. He will so seldom observe a dollar's worth of results given in exchange for a dollar spent that he will form a poor opinion of operating-efficiency and management. This highly-scientific department, requiring an amount of skill and executive ability equaled in few, if any, of the professions, certainly falls short of the standard established in our greater manufacturing industries. It is easily said that this is due to the diversity of conditions in mining, milling, and smelting. But on second view it must be admitted that there is room for tremendous improvements in nearly every mining-organization. The proposal of such improvements is often met by the argument that any mine

Sep 1, 1912

By C. W. Parmelee

THE ideal fuel for burning ceramic wares is the one that, among other characteristics, has little or no sulfur. For that reason wood was long considered the most desirable fuel but its high cost has practically eliminated its used except in regions where it is very abundant or other circumstances warrant its choice. The fuels commonly employed are natural and producer gas, oil, and coal. The last named is undoubtedly the most important, not only in this country but abroad. Occasionally anthracite is used but the larger part is bituminous. The quality of the coal used depends on the kind and the value of the products being manufactured. For some materials, such as common brick, hollow block, etc., the quality of the coal is of less importance than in the manufacture of polychrome terra cotta, pottery, porcelain, etc. It is obvious that in burning clays that contain notable amounts of pyrite, marcasite or gypsum, as is the case with many common clays, the sulfur content of the fuel is of much less importance. The permissible amount of sulfur in the coal used will depend on the kind of product being manufactured. "A good sample' of coal commonly used in pottery ovens has something like this quantity of sulfur." PER CENT. Total sulfur 1.20 Sulfur in the ash 0.11 Volatile sulfur a 1.09

Jan 9, 1919

By F. J. Plecity, J. T. Michalak, W. C. Leslie

W. M. Williams (McGill University)-The authors are to be congratulated on completing this detailed investigation of recrystallization behavior. The present writer has recently completed some research at the University of Toronto on the recrystallization and grain growth behavior of a number of "pure" irons, and he would like to take issue with the authors' contention that recrystallization cannot be followed by means of hardness measurements. Two series of specimens of Ferrovac E, a com- mercially available iron, were annealed to complete recrystallization at 525" and 620" C, measurements being made both of Rockwell hardness and of volume percent recrystallized as a function of annealing time. Good correlation was found between these two quantities and, following the earlier practice of Cook and Richards for copper, hardness measurements were used in an extensive investigation of recrystallization. No anomalous behavior was observed as a result of this practice. Specimens which showed complete softening always showed, (metallographically and by X-rays), completely re-crystallized structures. These observations do not, of course, detract in the least from the results of the work under discus-

Jan 1, 1962

By James P. Roe

I. INTRODUCTION. THOSE who deem the subject of this paper an old and super¬seded one may recall with advantage the words of the great proverb-maker, bidding us to seek the new in the ashes of the old. The manufacture of wrought-iron began with the small hearth built upon an eminence, and relying on the wind for blast. Next came, either the hearth about 12 in. in diameter by 2 ft. in height, blown by a man operating two goat-skins for bellows, or, a hearth of greatly varying diameter and about 10 ft. high, depending for its blast upon natural draft. The former appeared in India, the latter in Burmah; and both were in operation until quite recently, though their origin is lost in prehistoric times. The Catalan forge was the evolutionary descendant of the foregoing, and the parent of the Blase-ofen, which in turn led to the high bloomary or " Stückofen," the father of the blast-furnace, as a producer of cast-iron. The production of cast-iron checked the growth of the direct processes; and led to the introduction of various hearths, such as the Walloon, for low-silicon irons; and the South Wales process, combining the run-out fire with the finery, for higher-silicon irons. Some of these are still in operation in localities possessing the necessary raw materials; and their product is used for purposes requiring wrought-iron of exceptional quality, the supply of which is still smaller than the demand. We have to look back but a century and a quarter to see the introduction of the puddling process by Henry Cort; a process which, reinforced by the iron-oxide bottoms and fettling of Hall, was not less revolutionary in character, and more revo-

Jul 1, 1905

By A. W. Ambrose

THE underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of water in the base of an oil sand present a very serious problem to an oil company; sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas.

Jan 9, 1920