Search Documents

By A. Satter

Studies of wellbore heat transtnission during the injection of a hot fluid, as either gas or liquid, have appeared in he literature. The present investigation takes into account the effect of condensation, which is of practical sig-nificance when considering steam injection operations. Calculation procedures are given for superheated and for saturated and undersaturated steam. Effects of injection rate, time, pressure, temperature and depth of a well on heat losses have been analyzed. The benefits of using a packer are discussed. Also presented are correlations for estimating heat losses involved during injection of saturated steam. INTRODUCTION Studies of wellbore heat losses during the injection of a hot fluid have appeared in the literature. Ramey' has presented a useful solution for calculating temperature of a heated gas as a function of depth and injection time. Ramey and others have also presented solutions for the hot liquid case.'. ' No method is available to take into account the effect of condensation, which is of practical significance when considering steam injection operations. This paper presents a method of estimating the quality of a condensing fluid as a function of depth and time. The approach is basically the same as that used by Ramey. The following injected fluids and conditions are considered in this study: 1. Injection of superheated steam A. Decrease in temperature until cooled to the saturated state B. Condensation until condensed completely into hot (saturated) water 2. Injection of saturated or undersaturated steam; condensation until condensed completely into hot (saturated) water. Although this investigation does not include cooling of water after steam is completely condensed, Ramey's solution for the hot liquid case can be used for this purpose. The effects of various process variables on heat losses During the injection of steam into a well are investigated. THEORY QUALITY OF CONDENSING STEAM Predicting the behavior of condensing steam flowing down the injection wellbore requires an estimate of the quality of steam, i.e., the mass fraction of vapor in the mixture. Let us divide the total depth of the injection well into several segments which might be, but do not have to be, of equal magnitude. Consider condensation within a given depth interval AZ, the bottom of which is located at a depth Z from the surface (Fig 1). The following equation, derived in the Appendix- relates the quality of steam at the bottom of an interval to that at the top of the interval:

Jan 1, 1966

By C. O. Rison

HIGH explosives, particularly nitroglycerin, have been used in torpedoes for the purpose of shooting oil and gas wells for more than 60 years. The early history of the oil industry in Pennsylvania is not clear as to who actually torpedoed the first well, although in 1865 the Roberts Torpedo Co. procured a patent covering the process. Gunpowder was first used, although nitroglycerin was substituted shortly afterwards. Wells are shot for the purpose of increasing the flow of oil and gas A shot-hole in the producing horizon, with its contributory fissures and fractures, increases the area of and stimulates drainage into the hole. The shot-hole also acts as a collecting basin from which the oil is pumped. As a rule, hard or close-grained sands or limes are shot, other more or less porous and soft formations usually do not require shooting. and might be injured by blasting. Shooting is also resorted to in mechanical trouble such as straightening crooked holes, sidetracking pipe or tools, and for severing frozen strings of casing or drill pipe. Explosives arc also used sometimes to extinguish oil or gas-well fires although that work, which involves unusual conditions and methods, does not properly come within the classification of oil-well shooting. Some Factors to Be Considered in Shooting Wells Although nitroglycerin has been used extensively for more than half a century in shooting oil and gas wells, there is still a great deal of uncertainty as to the proper method of shooting or the amount of explosive required to produce best results in a particular formation. The possibility of shooting unproductive or cavey formations above or below the productive horizons, shooting into lower water, destroying casing seats, and the splitting or collapsing of casing strings, are factors that require consideration. The engineering departments of a number of the larger oil companies are making a study of methods of shooting, and the amounts of liquid nitroglycerin or other explosives required in shooting various productive

Jan 1, 1929

By M. R. Meyer, W. T. Walter

A great deal is known, in a qualitative sense, about the performance of CMI EB-36 centrifuges. The manufacturer can give reliable guidance for the proper operation of its centrifuges and can give general estimates of expected product moisture and recovery. Quantitative estimates of the effects of changes in the various operating parameters are more difficult to find. The engineer faced with designing a preparation plant may be without the specific data needed to make decisions. For example, to obtain optimum product moisture when drying 9.5 mm X 595 µm (0.4 in. x 28 mesh) coal the centrifuge manufacturer recommends having no more than 5% -595 µm (-28 mesh) material in the centrifuge feed. They know that more -595 µm (-28 mesh)material in the feed will cause higher product moistures, but they usually cannot quantify the increased moisture or describe the shape of the product moisture versus -595 µm (-28 mesh) in the feed curve. This study was conceived to provide quantitative information on the EB-36 centrifuges, focusing on product moisture, recovery, and size degradation. All of the centrifuges tested were Model EB-36 dryers from Centrifugal and Mechanical Industries Inc. (CMI), with feeds in the nominal 9.5 mm x 595 pm (0.4 in. x 28 mesh) range. These are typical centrifugal dryers in this application, and many were available for testing.

Jan 1, 1984

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature 1135°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By J. A. Retty

HOLLINGER CONSOLIDATED GOLD MINES LTD., through two subsidiary companies, has the exclusive right to prospect in two contiguous areas in central Labrador. This paper presents the results of the mineral exploration that has been conducted in these areas to date. One of the subsidiaries of Hollinger. the Labrador Mining and Exploration Co. Ltd., under an agreement with the Newfoundland Commission of Government, holds an area of approximately 20,000 sq.mi., which comprises the western portion of Newfoundland-Labrador and includes the upper basins of the Hamilton and Naskaupi Rivers. (The main area of the deposits so far discovered may be located on a map at about 67° west longitude and 55° north latitude.) The other subsidiary of Hollinger, Hollinger North Shore Exploration Co. Ltd., has licensed from the Province of Quebec an area of approximately 3900 sq.mi. lying directly north of the Newfoundland-controlled area at the headwaters of the George, Whale, and Swampy Bay Rivers. The M. A. Hanna Co., large iron-ore operators of the Lake Superior region, are participating in the project. With the exception of the years 1940 and 1941, field work has been conducted in the Newfoundland area since 1936, and in the Quebec area since 1939. Hollinger assumed the management in 1942. The field base is at Hollinger Lake, some 300 miles north of the tidewater base at Seven Islands, Quebec, which, in turn, is just west of the mouth of the Moisie River, on the Gulf of St. Lawrence. Air transportation is used exclusively to service the operation.

Jan 1, 1945

By Charles S. Barrett

Metallurgists are making use of the stereographic projection to a steadily increasing extent. In the last five years no less than 20 papers in American metallurgical journals alone have employed the stereographic projection; recent books on physical metallurgy, plastic deformation, X-rays and their applications, and crystal structure use it. Mineralogists have used the stereographic projection for many years in the description of symmetry classes and crystal planes, for it presents an accurate, easily understood plot of any angular relations in crystals with all unessential features eliminated (such as the accidentally determined size and shape of crystal faces). In metallography and physical metallurgy the projection is much used for the analysis of markings appearing on polished grains: slip lines, twins, cracks, structures formed by precipitation, magnetic-powder patterns, etch pits, etc. Data from certain types of X-ray photograms are most conveniently analyzed by its use, particularly those for determining the orientation of single crystals or the preferred orientation of grains in an aggregate. Calculations of how to tilt or cut a crystal parallel to a certain crystallographic plane or to reflect X-rays from a certain plane are rapidly carried out. It has been adopted almost universally to the exclusion of other methods by those studying the deformation of metallic crystals, save where the accuracy required is greater than a few tenths of a degree. Any directional property in a crystal or polycrystalline material can be shown on a stereographic projection; for example, the modulus of elasticity, yield point, etc. It has been repeatedly called to our attention that there is need of an elementary explanation of the principles and methods of stereographic projection, covering all the common applications in the field of metallography and physical metallurgy. The following contribution is an attempt to fill this need. The description of each method is supplemented with references to publications in which the method has been used. For convenience to the reader, these illustrative references are chiefly in American journals, particularly the publications of the American Institute of Mining and

Jan 1, 1937

By C. E. Lesher

Low-temPeRatUre carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus ?-in. or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal. of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic consumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold. Acknowledgments During the 10 years in which the work that is summarized in this paper has been under way, many have contributed time and effort, faithful service and fruitful thinking. Whatever success has attended

Jan 1, 1940

By C. E. Lesher

Low-temPeRatUre carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus ?-in. or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal. of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic consumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold. Acknowledgments During the 10 years in which the work that is summarized in this paper has been under way, many have contributed time and effort, faithful service and fruitful thinking. Whatever success has attended

Jan 1, 1940

By C. M. Wayman, J. F. Breedis

The crystallography of the martensitic transformation in the Fe-30 Ni alloy was reinvestigated. The scatter in the habit Plane as determined from measurements on the mid-rib plane was smaller than reported previously, and the orientation relationship was determined from a martensite plate having known direction cosines. From agreement with crystallographic theory and from observations of the morphnlogy of the martensite plates, it is suggested that the mid-rib plane represents the starting region of the transformation. THE crystallography of the martensitic transformation in the iron-nickel system has been the subject of many investigations.&apos;-7 However, for iron alloys containing approximately 30 wt pct Ni, a wide scatter in the reported habit planes exists. In only one instance has a Laue determination of the orientation relationship been made, but the habit plane of the martensite plate studied was not determined experimentally. Because the most successful thermodynamic and kinetic analyses8 of the martensite transformation have been based on Fe-30 Ni alloys, it was considered desirable to reinvestigate the crystallographic features of the transformation in this alloy. Lieberman9 suggested that the most significant information for use in a theoretical treatment involves the determination of all the crystallographic observables from a single plate of the product phase. This was first done in essence by Greninger and Troiano10 for Fe-22 wt pct Ni-0.8 wt pct C, and is the method followed in this investigation. Some theoretical approaches11-13 in describing the martensitic transformation consider the overall transformation distortion to be comprised of a Bain distortion, or lattice deformation (PI, which produces the structure change, and a lattice invariant deformation (G), such as twinning, which together leave the interface or habit plane un-distorted. The incorporation of a rigid body rotation (R) results in a transformation distortion (E) such that the interface plane is left both undistorted and unrotated. In matrix notation, E = RPG where the lattice invariant deformation has "taken place" in the austenite. Bowles and Mackenzie14-16 in formulating a theoretical approach proposed an adjustable scaler quantity, denoted as 6, which represents a uniform dilation in the interface plane. This dilation acts to adjust the lattice spacings of the parent and product structures at the plane of contact. Using the dilation parameter as a variable, these authors were able to account for a continuous variation of habit planes in steels along a curve in the stereogram between {225}A and {259}A. she invariant line strain14 of the transformation is 6 RP, and the corresponding transformation distortion is E/6.) With the dilation parameter known, the invariant line is computed as the triple coincidence of the habit plane, the shear plane of the lattice invariant deformation, and the initial Bain cone.14 The contraction axis for the Bain distortion can be taken9&apos;17 as [010]A, and the correct permutation of the habit plane indices used. Kelly and Nutting 18 have established the shear plane (of twinning) in the tetragonal martensite of Fe-22 Ni-0.8C to be {112)M by means of transmission electron microscopy. The reasonable shear system is then {112}M which is equivalent to {011}A <01l>A. The as-

Jan 1, 1962

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°F.) for 15 min., cool rapidly to casting temperature, and cast.&apos; In Germany superheating is carried out at 850&apos; to 900°C. (1560° to I650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (I740°F.).2 In the United States superheating is carried out at 1600&apos; to 1700°F. (871&apos; to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.! in heavy sections and from 60 to IOO in 1/2-in. sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. Materials and Methods The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 Per cent aluminum, 2 per cent zinc, and 0.1 per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By Everett G. Trostel

AMERICAN industry in 1943 emerged from the construction phase into the production phase, and American military operations passed from preparation into full action in the many theaters of the global war. The increased pace of industrial and military operations has resulted in a tremendous demand for petroleum and its products.

Jan 1, 1944

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°°F.) for 15 min., cool rapidly to casting temperature, and cast.1 In Germany superheating is carried out at 850° to 900°C. (1560° to 1650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (1740°F.).2 In the United States superheating is carried out at i600° to 1700°F. (871° to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.§ in heavy sections and from 60 to l00 in 3-in sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. MATERIALS AND METHODS The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 per cent aluminum, 2 per cent zinc, and 0.r per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By Henry S. Drinker

(Canal Zone Meeting, November, 1910.) FEW men reach middle life without having had the experience of failure in one or more undertakings; and most of us can look back with gratitude to help or advice given us by friends at critical periods of our lives. If, as men, we ask and take the benefit of such aid, why should we expect our sons to be stronger? A parent can make no greater mistake than to send a boy, however steady and intelligent he may be, off&apos; to school or college, and expect the boy always to cope successfully with all the new conditions and new difficulties that may confront him. This is undoubtedly more the case with a freshman, in his first year at college, than in later years, or than it is with a boy at day- or boarding-school, where the boy receives a greater degree of care and oversight than can be given to the young man entering college; of all periods in life, the youth in his freshman year-fresh from the overshadowing care of home and school-may need judicious advice and timely aid. The change from the restraint of home and school to the freedom of college life is sudden and marked, and it is in this the first year of the boy or young man of 17, 18, or 19 years of age, that some tactful, judicious aid should be near him in his work and course. Some boys go to college so well prepared that they become careless and finally fall behind in their work from over-confidence. Others meet trouble from ambitiously trying to do more than their previous preparation, or physical or mental strength, can sustain. Others fall behind from illness-from injuries-from natural inability to grasp at first, without more aid than comes to them in the regular course of instruction, the higher mathematics-or mayhap the modern languages, or other subjects presented by the advanced curriculum of the present day. When a boy or youth begins to

Jan 1, 1911

By T. C. Campbell

Copper is extracted from the Chuquicamata oxide ore by a hydro-metallurgical process. The ore is crushed to 3/8-in. sizing, and leached with a sulfuric acid electrolyte. Chlorine is precipitated. and the ferric iron reduced in the enriched electrolyte, after which the copper is recovered by electrolysis with insoluble Chilex and lead-antimony anodes, the spent electrolyte being returned to leaching. Cathodes are melted and refined in market furnaces and cast into commercial wire-bar and cake shapes. Sulfuric acid for the process is supplied by the brochantite in the ore. Water for washing the ore is advanced through the solution system and finally after cutting by electrolysis to from 6 to 16.0 grams per liter is completely stripped by the cuprous chloride method and run to waste. The cuprous chloride so obtained plus that resulting from precipitation of chlorine from strong solution is dissolved in ferrous chloride brine and the copper cemented on scrap iron. The cement so obtained is in part used to reduce ferric iron in electrolyte, and as it is of exceptional purity is also furnace refined and cast into an exceptional quality of fire-refined copper. Fig. 1 is flow sheet of the operation. The reduction plant is composed of seven divisions as follows: (1) crushing, (2) leaching, (3) tailings disposal, (4) dechloridizing, (5) sulfur dioxide treatment, (6) electrolytic tank house, (7) smelting and melting. A brief description of each of these divisions will be given. Crushing Ore that is frequently blocky and up to 5 ft. in section is crushed in four stages to 3/8-in. mesh. The first stage of crushing is called primary and the next three stages are known as secondary crushing. The first stage is accomplished with two 60-in. Superior McCully gyratory breakers by which the ore is broken to 9 in. The second coarse gyratory breakers crush the ore to 3-in. sizing. There are seven No. 10 McCully gyratories in this service, for one of which recently has been substituted a No. 7 cone crusher. The third and fourth stages of crushing are accomplished by fifty 48-in. disk crushers. In the third stage 14 disk crushers break the ore to 1 in., and in the last stage 36 disk crushers turn out the final product of 0.371-in. sizing. Reference to the flow sheets of Figs. 2 and 3

Jan 1, 1934

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By George W. Bain

Methods of mining building stone of any sort are planned to produce as few fractures as possible, and present a strong contrast to methods of mining metallic ores, which must be crushed eventually and have fractures produced in as great profusion as possible. Shocks transmitted to a stone invariably make it more porous and more permeable and reduce its effective life, therefore methods of mining building stone involve as This building illustrates the fine detail of workmanship, unprotected sharp corners and thin edges, and tall narrow columns characteristic of marble structures. These features require exceedingly coherent stone, and preservation of these features for decades or centuries demands many special quarrying precautions to keep absorption to 0.14 per cent or less, a detail not essential to stone for coarser architectural types. few shocks as possible. This is singularly true for marble because marble structures are intended to have long life, greater delicacy of line, more gracefulness and fineness of sculpture than those made from any other structural material (Fig. 1). So that delicate lines may remain in almost perfect preservation for decades, or even centuries, it is important

Jan 1, 1938

By George W. Bain

Methods of mining building stone of any sort are planned to produce as few fractures as possible, and present a strong contrast to methods of mining metallic ores, which must be crushed eventually and have fractures produced in as great profusion as possible. Shocks transmitted to a stone invariably make it more porous and more permeable and reduce its effective life, therefore methods of mining building stone involve as This building illustrates the fine detail of workmanship, unprotected sharp corners and thin edges, and tall narrow columns characteristic of marble structures. These features require exceedingly coherent stone, and preservation of these features for decades or centuries demands many special quarrying precautions to keep absorption to 0.14 per cent or less, a detail not essential to stone for coarser architectural types. few shocks as possible. This is singularly true for marble because marble structures are intended to have long life, greater delicacy of line, more gracefulness and fineness of sculpture than those made from any other structural material (Fig. 1). So that delicate lines may remain in almost perfect preservation for decades, or even centuries, it is important

Jan 1, 1938

By Edwin B. Wilson, Joseph W. Leonard, Richard W. Borio

preparation of specification coals for the utility industry is approached from the standpoint of a cooperative effort with the power company to assure that the shipped product will be a noncorrosive coal. Selective mining, coal preparation, the use of additives, and coal blending are mine-site techniques proposed as means for upgrading corrosion-retarding constituents of utility coals (CaO and MgO) while, at the same time, reducing the concentration of those constituents of coal (Na20 and K,O) which cause corrosion. Data obtained from large-scale boiler testing in combination with bench-scale physical and chemical tests are used as a basis for the formulation of mine-site procedures to improve coal combustion utilization. Electric power generation remains the greatest market for coal in the United States. A major reason for this strong market has been the ability of the coal industry to supply a superior product for combustion while maintaining competitive prices. Now that the coal industry is engaged in intensive competition with nuclear power for future energy demand, it becomes ever more imperative that superior coal products are produced. One important problem when burning some coals is a liquid phase corrosive attack on boiler tube metal in the superheater and reheater areas of the furnace where steam temperatures may exceed 1050°F. In addition to causing power outages and high maintenance costs, corrosion is a continuing barrier to the future development of more efficient steam cycles which permit lower generation costs when using coal. Research methods of the past which have been directed at finding solutions which could be applied at the power plant site have been only partially successful and are generally costly. This paper contains a suggested --method of corrosion control through investigation of the problem at the source of the trouble—the coal supplier facility. It is proposed that mine-site pre-ventative procedures be considered as an effective means of cooperative corrosion control between the power company and the coal supplier. Economic justification must be applied to the individual situation. This paper is based on recent work by Combustion Engineering, Inc. and the Coal Research Bureau of West Virginia University under a contract from the Department of the Interior Office of Coal Research.&apos;,&apos; Results which are of importance to this discussion may be summarized as follows: 1) The alkali minerals of coal (Na2O and K2O), as measured by an acid leaching process, can be related to corrosion rate in utility boilers. As these constituents increase in a coal product, its corrosiveness can be expected to worsen. 2) The alkaline-earth minerals contained in coal, reported as total CaO and MgO reduce corrosiveness 2s their concentration increases. 3) Naturally occuring, alkaline-earth-bearing materials, such as limestone and dolomite, may be added to a coal to reduce its corrosiveness. 4) Coals with very low iron contents tend to be less corrosive. These results provide the groundwork for examination of the system of operations which occur at the supplier facility from the seam face where mining is begun to the point of loading for shipment. The Mining System Fig. 1 is a cross section of one of the typical coal seams (designated coal A) that was boiler tested during this research program. This seam is overlain by material which consists primarily of a gray-black shale. In the lower third of this seam, there exists a thin rock parting of less than 4 in. in thickness which is consistent throughout the seam. The floor material is fireclay. In order to examine mineral distribution throughout this particular seam, the Coal Research Bureau collected a

Jan 1, 1971

By T. D. McKinley

Theory, operational characteristics, and indicated precision and accuracy of analytical methods based on vacuum extraction, equilibrium pressure, and combustion approaches are reviewed. At the present time vacuum extraction at 1400°C and the equilibrium pressure method are recommended for determination of hydrogen in titanium and titanium-rich alloys. UNTIL a few years ago the role of hydrogen in titanium was an unknown factor with regard to its effect on the physical and mechanical properties of the metal. However, following the work of Jaffee and othersa-" it is now generally acknowledged that hydrogen has a degrading effect on titanium and its alloys. The chief manifestations are a decrease in impact strength in -systems and delayed cracking in a-ß systems. Since hydrogen does have a de- grading effect on titanium it is essential to control it within tolerable limits. It then follows that procedures for quantitative estimation of hydrogen are a primary requirement for the industry. For greatest benefit these methods should be simple, rapid, and precise. In addition to having these virtues, methods must be easy to duplicate in both equipment and technique to gain widespread use. After inherent accuracy has been established, the, required precision to make a method acceptable is dependent largely on the nature of the work at hand. Ability to obtain a representative sample has a pro-

Jan 1, 1959

By John J. Egan, A. B. Kinzel, Walter Crafts

The demands of the petroleum and chemical industries for steels to be used in pressure vessels and similar structures at artificially low temperatures are continually increasing, and the writing of proper specifications with suitable tests becomes increasingly important. Likewise, the selection of suitable steels for such applications is of increasing concern to the metallurgist. It is generally recognized that highly alloyed steels of the austenitic stainless type retain their properties even at very low temperatures and represent the best technological solution of the low-temperature steel problem. However, in many instances less expensive carbon or low-alloy steels suitable for service within limited temperature ranges are available. The problem thus becomes one of defining the various factors involved in the production and fabrication of these less expensive steels and determining the temperature ranges in which their properties justify engineering application. Most of the applications involve welded structures, and the heat effect of welding as well as the nature of the weld metal are matters of prime concern. The first problem that the metallurgist faces is the determination of the type of test to be used as a criterion of the performance of the steel in low-temperature service. It has been generally recognized that the static properties of steel as determined in the ordinary tensile test undergo a gradual and relatively slight change as the temperature of test is lowered in the range of current interest; i.e., from room temperature to minus 120&apos; C. It is further generally recognized that the behavior of steel under impact involving notch sensitivity is definitely affected at the lower temperatures. While the major subject of this paper is the effect of grain-refining deoxidizers, of low-alloy additions and of welding on the low-temperature notched-bar impact properties, an inquiry into the general behavior of steel under low-temperature impact testing is included. This is a pertinent portion of the investigation and the results thereof are

Jan 1, 1937