Search Documents

By H. C. Johnson, J. K. Elliott

One of the primary requirements for successful operation of an enriched gas-drive project is to control the composition of injection gas. This can become a serious and difficult problem, particularly in cases where the enrichment material is being furnished from a number of field -produced gas streams. It is possible to effect control of the injection gas composition through frequent or continuous sampling; however, this can be extremely costly and, in many cases, impractical due to laboratory requirements of time. Another alternative would be to provide a calculation technique which would be flexible and sufficiently accurate to predict composition of the liquid and gas streams of interest at any point in the system. The purpose of this paper is to discuss a technique that was used successfully on an operating enriched gas-drive project for developing information which could be used for controlling composition of the injected gas. FIELD OPERATIONS The particular field (hereafter called Example field) in the example operation being discussed is composed of four oil reservoirs (A. B, C and E) and one gas condensate reservoir (D). Casinghead gas from the oil reservoirs and gas from the gas condensate reservoir are gathered through a field gathering system as shown in Fig. I for injection into Reservoir C. The gas mixture which is recovered from the five reservoirs for injection purposes is composed of gases liberated in 19 individual separators, each operating at a separate temperature and pressure. PROPOSED CALCULATION TECHNIQUE It is well known that vapor-liquid equilibrium calculations in general use throughout the petroleum industry can be used to predict reliably the phase behavior of hydrocarbon mixtures, particularly at pressures less than 1,000 psig. It is then a simple matter to account for the material on a ComPonent basis by m''ing flash and material balance calculations at each separation point in a hydrocarbon system. Accordingly, it was proposed to use vapor-liquid equilibrium and material balance cal- culations with a medium-sized electronic digital computer as a basis for developing a control procedure for use in controlling injection gas composition in the enriched gas-drive project. Although the approach is a simple one, the numerous vapor-liquid equilibrium calculations involved make the problem laborious; in this particular case, it would have been impractical to make sutficiently complete analysis without the aid of digital computing equipment. SAMPLING AND VERIFICATION OF CALCULATION PROCEDURE To obtain representative gas and liquid stream samples and to provide a quantitative measure of overall system Performance for comDarative purpLses, a thorough test of the field and plant system was conducted in the summer of 1957. Oil production at each battery was sta-

By William M. Sheehan

TRANSPORTATION is one of the most important problems of the mine operator and the possibilities of cost reduction in this field should not be overlooked. In the railroad industry, cars and locomotives have been improved greatly, and the progress there made is well worthy of study by the mine operator looking for maximum efficiency in every branch of his activities. One of the outstanding developments in the construction of railroad equipment in recent years has been the wide-spread adoption of large one-piece steel castings for the framework of locomotives, passenger and freight cars. Some of the advantages and applications of this type of construction will be outlined in this paper, with particular thought of the needs of the mining industry. The inherent qualities of cast steel: homogeneity, unrestricted size and shape, high tensile strength, flexibility of metal distribution, resistance to corrosion, and gracefulness of outline, make it the most versatile member of the ferrous group. Not only is it a strength-giving element, but it is corrosion resistant, a combination that makes for large economies in equipment maintenance. Flexibility of metal distribution allows the integral foundation to be in the shape best suited for the purpose. These cast structures are really assembled in the mold in liquid form and the metal can be placed in the right pro¬portion exactly where it is needed, thus securing weight economy and uniformity of fibre stress. Such a process permits the incorporation, with ease, of necessary brackets, utilizing them to provide not only greater strength for the derail part itself, but often to add to the value of the entire unit. Laps, seams, and joints, which are necessary in all fabricated forms, are eliminated.

Jan 1, 1933

By AIME AIME

MOST of the copper mines in Canada are favored by nature in having other metals besides, copper in their ore, which puts them in a most satisfactory competitive position. Noranda ore has an important gold content, Flin Flon gold and zinc, and International Nickel of course has nickel. All of the larger copper companies in Canada operated during 1.933 and the total production of copper exceeded that of the year before. The Britannia Mining and Smelting Co. worked out to succcessful conclusion a three-product flotation process for separating the copper, zinc and iron from its low-grade ore. Although the method and equipment is different from that used at the Flin Flon mine, the object is the same, that

Jan 1, 1934

By I. H. Warren, E. A. Devuyst

The selective dissolution of pyrolusite (MnO2) in presence of goethite (FeO•OH) in aqueous ammoniacal ammonium carbamate solution has been investigated: various reducing agents were studied, in particular sodium sulfite (Na2SO3,) and hydrazine hydrate (N2H4•H2O). Sodium sulfite was found to be an unsatisfactory reducing agent for both goethite and pyrolusite, for the leaching rate decreased steadily with time to an impractical level because of the limited solubility of the reactions products. Hydrazine hydrate was an effective reducing agent for pyrolusite even at low temperature, whereas goethite required much higher temperatures for any appreciable dissolution. A 1-hr leach at 35°C dissolved 90% of the pyrolusite but only 0.1% of the goethite. An activation energy of 17.0 Kcal per mole was found for the dissolution of pyrolusite with hydrazine. A reaction mechanism for the leaching of pyrolusite with hydrazine is proposed in which a reduction reaction on the surface of the mineral is the rate-determining step. The application of ammonium carbamate to the beneficiation of ilmenite is briefly described.

Jan 1, 1973

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By G. H. Matheson, J. M. W. Mackenzie

The flotation rate of coal has been studied using a continuous laboratory flotation cell and a multiple exposure photographic technique. The effects of particle size, reagent additions and cell turbulence on the flotation rate of coal have been investigated. The results have been analyzed in terms of current theories of particle bubble encounter and adhesion. The rupture forces which occur during particle bubble encounter have been shown to have an important effect on the flotation rate of coarse coal particles. The flotation of coal is a time dependent process, and in order to obtain a complete understanding of the operation it is necessary to determine the kinetics of the process. In coal flotation, the flotation rate and the associated values of cell productivity in terms of tons per kilowatt-hour and tons per cubic foot of cell volume are of greater importance than in most other mineral flotation operations. The reasons for this are associated with the low unit value of coal and the relatively high cost of coal flotation compared with other coal cleaning processes. An important aspect of coal flotation kinetics is the design of coal flotation cells. The cells used in many coal cleaning operations are often replicas of those used for the treatment of sulfide ores and are not necessarily suitable for the treatment of coal washing pulps, which usually contain a higher percentage of coarse and floatable material than the sulfide pulps for which the cells were designed. This disadvantage of many coal flotation cells has been recognized by Russian engineers who, by the addition of baffles to their subaeration coal flotation cells have increased the cell capacity by 100%. Investigation of the variables which influence flotation kinetics and cell productivity are, therefore, important to the coal industry where flotation is the only accepted method of cleaning the fine (-1/2mm) coal. The kinetics of the flotation process have been investigated in detail by Schumann10 who developed a continuous flotation cell which permitted the study of flotation under steady state conditions. This technique has been used by Gaudin et a1.,6 Brown and Smith and recently by Jowett and Savfi.7 The latter authors have developed a refined mathematical treatment for interpreting the results of continuous laboratory tests. Attempts have also been made to study flotation kinetics using conventional batch testing techniques. The experimental difficulties, however, and the problems of determining the order of the flotation rate process have made this technique of dubious value. A summary of the proposed rate equations for batch testing and the difficulties associated with this technique is given by Brown and Smith. 2 The experimental techniques described above are concerned with the rate of production of froth product. However, several authors, notably Sutherland, 11 Bogdanov1 and Philippoff, 9 have analyzed flotation

Jan 1, 1963

By W. W. Simpson, W. L. Staker, R. G. Sandberg

The Bureau of Mines investigated selective extraction of Au and Ag from a low-grade Au ore containing Hg. Gold and silver were extracted from the ore in cyanide slurries, and Hg extraction was suppressed with sodium or calcium sulfide. Maximum Au extraction and minimum Hg extraction were obtained using solutions containing 17 kg NaCN/t of solution (0.34 lb NaCN/st). Increasing the cyanide concentration increased Hg extraction without increasing Au extraction. Mercury extraction from the ore was suppressed with 0.5-2.9 kg CaS/kg Hg (0.5-2.9 lb/lb) in the ore. Gold-to-mercury ratios of 100:1 to 400:1 were obtained in the leach solution, and on the activated carbon in a CIP circuit.

Jan 1, 1985

By Cyrus Garnsey

NECESSITY FOR PRICE FIXING DURING the latter part of 1916 and the early months of 1917, clue to war activities, there was a threatened shortage of coal which resulted in panic among consumers and a rush to obtain coal at once at any price. As a result of this insistent demand for immediate delivery, prices were bid up by the consumers to unprecedented heights; spot coal which had previously been selling at from $1.50 to 82 per ton was bid up to $5, $6, and, in exceptional cases, as high as $7.50 or more per ton. Then when the April, 1917, contract period arrived, contracts could be made only at prices ranging from $3 up to $5 and $6 per ton for the year's delivery. This condition caused such a demoralization of the business, and so much complaint, that some action to regulate prices was considered essential by the National Administration. LANE-PEABODY AGREEMENT In May, 1917, a committee under the chairmanship of F. S. Peabody, of Chicago, was appointed by the Council of National Defense, through Mr. Lane, to consider the whole question of bituminous coal. This committee, with the Secretary of the Interior, Mr. Lane, after numerous meetings and long negotiations with the operators throughout the country, announced on June 29 an agreement between the Committee and the producers, fixing a tentative maximum price for bituminous coal throughout the country at $3 per net ton f.o.b. mines, to which was added 25 c. for selling commission to wholesalers. This plan was based on the idea of fixing a maximum price, high enough to greatly-stimulate production, with the expectation that the laws of supply and demand would, with ample production, operate to maintain fair and just prices for coal throughout the country.

Jan 9, 1918

By R. S. Dean

The commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in Mining and Metallurgy for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for " the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. Practice at BouldeR City The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: 1. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By R. S. Dean

The commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in Mining and Metallurgy for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for " the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. Practice at BouldeR City The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: 1. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By P. Chiotti, R. J. Hecht

Vapov pressure data of solid and liquid alloys along with phase diagram data WERE employed in calculating the thermodynamic properties for the Ca-Zn system. The relative excess partial molal free energy for zinc in the liquid alloys was fitted to the relation wnvre i is we tvmpvrutiirc in ucgrees neivtu ana in is the tr~ole fvaction. Relations for the standard free energy of fortnation for the eight cornpounds were developed. ThE phase diagram for the Ca-Zn system as determined by Messing et a1.' is reproduced in Fig. 1. Earlier work on the phase diagram has been summarized by Hansen and Anderko2 and the very limited thermodynamic information for this system has been reviewed by Hultgren et a1.3 The heat of fusion for the compound CaZn2 has recently been determined to be 9260 cal per mole.4 Solubility data for calcium in zinc for the temperature range of 650" to 725°C were fitted by the relation and reported by Johnson and Dilloon5 In the present investigation zinc vapor pressure data were obtained by both the dewpoint and Knudsen methods in order to calculate the thermodynamic properties for liquid and solid alloys. The dewpoint method as employed in this work requires that only one of the components be significantly volatile, in this case zinc, and that the vapor pressure of pure zinc be known. For calculation purposes the vapor pressure data for pure zinc3 were fitted to the relations; for temperatures below 692.7K, the melting point of zinc. The corresponding free-energy relations for vaporization and sublimation of pure zinc are respectively. Some of the calculations also required knowledge of the free energy of fusion of zinc and calcium and the free energy for the 721°K allotropic transformation of calcium. The free energy of fusion of zinc was taken to be the difference between Eqs. [4] and [5], or The free energy of fusion and transition for calcium were based on the enthalpy values of 2040 and 222 cal per g-atom, respectively, as reported by Chiotti et al. 4 and the heat capacity data given by Hultgren et a1.3 and are represented by the relations, In the latter expression the difference in heat capacity between the a and 0 forms of calcium was neglected. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in preparing the alloys were Bunker Hill slab zinc, 99.99 pct pure, and Ames Laboratory calcium. The average impurities in the calcium in parts per million by weight, ppm, were N-17, H—77, Ba—216, Mg-15, Si—7, C—157, and Fe—9. The zinc was cleaned in dilute nitric acid and the calcium was used as received. The calcium was stored and handled in an argon-filled glove box and when removed from the dry box it was kept in an argon-filled desiccator. Tantalum was found to be a suitable alloy container. The alloy components were contained in a 1-in.-diam cylindri-

Jan 1, 1968

By J. E. Strassner

Oilfield emulsions are stabilized primarily by film-forming asphaltenes and resins containing organic acids and bases. Adding inorganic acids and bases radically changes the physical properties of these films and their emulsion-stabilizing properties. Interfacial films show one of three different physical characteristics when retracted in pendent drop tests. These compressed films have rigid, soap-type or minimum film properties depending on the quantity of asphaltenes and resins in the crude oil and on the pH and composition of the brine. There exists for each crude oil-brine system an optimum pH range over which the adsorbed film exhibits minimum contracted filtn properties. In this range, intmfacial tension is high — frequently near its maximum value — indicating the absence of highly surface-active specier; crude oil-brine emulsions generally show minimum stability; and surfactant requirements for breaking these emulsions are significantly reduced — sometimes no surfactant is needed. About two-thirds of the world's crude oil is produced as emulsions that must be treated (demulsified) to be marketed.' Approximately three-fourths of all domestic crude oil produced must be treated. The percentage of crude requiring treatment increases as fields become older and more water is produced. Demulsification most frequently is attained through use of surfactants, heat and electric treaters. It is estimated that over 75 percent of all oilfield emulsions are broken by chemicals generally containing alkylene oxide condensates. Although acids and bases are known to affect emulsion stability:-' they rarely are used in the oil field except in batch treatment of the most severe emulsions. Nevertheless, pH adjustment by using acids or bases in demulsification has some advantages over other methods. Mainly, it is cheaper. Acids and bases frequently are cheaper to use than surfactants, or can appreciably reduce the amount of surfactant required for demulsification. Secondary advantages are that less oil is lost by emulsi-fication into the aqueous phase, and that less corrosion is encountered when the optimum pH is basic. Limitations to the use of pH include (1) use in brines containing high concentrations of reactive ions, (2) closer supervision for pH control than is required for surfactants and (3) need for corrosion protection when the optimum pH is sufficiently acidic. These factors indicate that the economics of pH con trol in demulsification will be maximized when relatively large treating facilities are needed, when relatively large surfactant concentrations are required to break an emulsion, when a relatively low concentration of the aqueous phase is emulsified in the oil and when the emulsified aqueous phase contains relatively low concentrations of reactive ions. Because there are no broad guide lines for using pH control in breaking oillield emulsions (and because the limited guides available are highly specific and frequently contradictory), this paper will attempt to clarify the principles involved in using acids and bases to break emulsions. These principles also should be useful in refinery separations and in other oilfield applications where stable or unstable petroleum emulsions are involved. Principles of Emulsion Stability Oilfield emulsions generally occur as water droplets dispersed in oil (w/o) and occasionally as oil droplets in water (o/w). These emulsion droplets are usually in the 0.1- to 10-micron range. However, more coarsely dispersed water droplets frequently are present in the emulsion. Pure hydrocarbons and water will not form stable emulsii except in extreme dilutions where the large distance brtween droplets inhibits coalescence. An emulsion breaks because interfacial tension acts to minimize the surface area of the dispersed drops by coalescence. However, emulsions can be stablized for long periods of time by the presence of a third phase that adsorbs at the oil-water interface and inhibits coalescence of the dispersed phase."' Emulsions generally are stabilized by (1) repulsive charges on the surfaces of the dispersed phase and (2) adsorbed films that, being preferentially wetted by the continuous phase, act as a physical barrier to inhibit contact between the dispersed droplets. Both these factors generally are important in stabilizing and in breaking o/w emulsions. However, repulsive charges are less effective in stabilizing w/o emulsions which generally are stabilized by adsorbed films.V or this reason the nature and importance of these films at oil-water interfaces were examined closely; as will be shown, pH changes were found to affect the films significantly, and this work led to laboratory tests of pH- adjustment in emulsion breaking. This paper will present evidence to show that emulsions are stabilized primarily by films that form around droplets

Jan 1, 1969

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757' and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick 'needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,' are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed' by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke's law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

By Hagh H. Bein

MOST mining engineers and geologists realize the value of photographs in their professional work. Members of each group use photographs to illustrate their reports, and articles and photographs, when available, will often save many words of written text in explaining some point or in proving some pet theory. No one hesitates to take aboveground pictures but many rarely take their cameras underground. However, underground photography, too, is really simple. I do not believe that anything new is offered here and the procedures given are merely a compilation of various methods I have tried and used, with some success, over the past six or seven years. The article will deal with photographs to be taken in metal mines, but only in those where no gas hazard exists, with resultant danger of explosions and fire. Some mining company geologists consider the camera a necessary part of their equipment and carry one on their daily trips to the various parts of the mine under their observation. I know of one company whose files of geologic sketches of heading, backs. and veins are supplemented by actual photographs so that a nice geologic picture

Jan 1, 1945

By D. H. Gieskieng

THE advent of curved jaw crusher wearing plates made an approach other than segmental layout analysis desirable for prediction of capacities. For some time it had been known that the drawing board capacities of crushers using these plates had to be considerably modified by complicated experience factors to achieve agreement with results. Because these apparent capacities could be readily increased severalfold by minor crushing chamber shape changes, it was necessary that the utmost precaution be taken in predicting capacities of jaw plates modified for nonchoking, special wear characteristics, or any other reason. To this end the laboratory and field tests outlined by the author in a previous paper1 were made on Blake-type jaw crushers. The results of these tests were summarized in a simple first degree equation applicable to crushers using either straight or curved jaw plates. This equation first outlines the maximum capacity potential of a given crusher, then reduces this figure in accordance with installation circumstances by means of a realization factor. It was found subsequently that this equation, with the addition of an eccentric throw factor, is applicable to standard types of single-toggle or overhead eccentric jaw crushers as far as maximum capacity potential is concerned. However, these crushers have realization factor curves somewhat different from those outlined for the Blake type. While this paper is concerned principally with standard type single-toggle crusher capacities, the evaluation of data obtained with these machines is simplified by comparative reduction to the 10 x 7 in. Blake-type equivalents upon which the summary of the preceding paper was made. Convertibility of data from one type of crusher to the other also tends towards confirmation of both. The agreement of these data is sufficient to be considered complimentary. Consequently the feed factors, f, previously reported for Blake crushers are slightly adjusted to an average with the single-toggle crusher results. Blake-type equation: C = f.d.w.y.t.n.a.r [I] Single-toggle type equation: C = f.d.w.y.t.n.a.e.r [21 where C is the capacity in short tons per hour through the crusher, f is a feed factor, dependent upon the presence of fines in the feed, and the surface character of the jaw plates used. Values of f : Smooth Plates Corrugated Plates With normal fines 0.0000414 0.0000319 Fines scalped out 0.0000368 0.0000252 Large pieces only . 0.0000312 0.0000215 d is the apparent density of the broken product in pounds per cubic foot. (If the true specific gravity of the feed is known, 40 pct voids may be assumed and d becomes 37.4 times sp gr). w is the width of crushing chamber in inches. y is the openside setting of the crusher, in inches. In the case of corrugated jaw plates it is measured from the tip of one corrugation to the bottom of the valley opposite. t is the length of jaw stroke in inches at the bottom of the crushing chamber. It is the difference between open and close-side settings. n is rpm, or crushing cycles per minute, a is the nip-angle factor. It is unity for 26" and 3 pct greater for each less nip-angle degree. A nip-angle of 20" has an a value of 1.18, and an angle of 30" has an a value of 0.88, see Fig. 1. r is the realization factor. It is unity for perfectly uniform choke feeding and usually less for actual operating conditions according to the method of feeding used and the probabilities of hang-ups involving the size of feed and crusher opening. Approximate values are given by the curves in Fig. 2. These values are further reduced by intermittent feeding, e is the throw or diameter of gyration of the single-toggle crusher eccentric in inches. As evident in Fig. 1A, variation of feed size will generally have little effect on nip-angle if both jaw plates have flat areas. Jaw plates having continuous curvature, as in Fig. 1B will have different nip-angles, depending upon the size of feed. For test work as described in this paper this effect was accounted. For general compilation of capacities for average feeds it is suggested that the nip-angle be taken at the various settings computed, at an arbitrary level, such as is indicated in Fig. 1C. Data Evaluation To bring the Blake and single-toggle type crusher capacity test results to common terms for evaluation, all data are converted to terms of 10 x 7 in. Blake-type performance at conditions of 100 lb per cu ft, 10 in. chamber width, 250 rpm, 0.65 in. stroke, 3-in. openside setting, and 18° nip-angle. (The nip-angle of the 10x7 in. Blake is 18° at 3-in. setting.) The single-toggle crusher performances are also divided by the eccentric throw to bring this effect to unity. As outlined,' laboratory and field tests made on Blake-type crushers ranging from 10 x 7 in. to 60 x 48 in. were summarized along the foregoing conditions of speed, stroke, etc. This resulted in groups of data which correspond to feeds with fines, feeds

Jan 1, 1952

By B. F. Fackenthall

The Durham Iron Works of Messrs. Cooper & Hewitt, near Riegelsville, Pa., occupy a site which has been almost continuously the scene of iron-manufacturing industry since 1727. Doubtless if Anthony Morris and his thirteen associates, who in that year erected a blast-furnace on the Durham Creek, a short distance above where the Durham Iron Works now stands, could have had a vision of the improved and enlarged apparatus of their successors, they would have been not less astonished by the huge stack, the hot-blast ovens, and the blowing-engines of the modern blast-furnace, than by the railroad which now follows the bank of the river on which their clumsy " Durham boats " once floated pig-iron to Philadelphia. In one particular, posterity must confess their snperiority. We are told that in November, 1728, they shipped three tons of Durham iron to England. The proprietors of the Durham Iron Works are not now shipping iron to England. The present Durham furnace was built (in place of two smaller ones) in 1874 and 1875, and made its first blast in 1876. A description of it, with other works of the same proprietors, at Trenton, N. J., by A. L. Holley and Lenox Smith, was published in London Engineering for January 31st, and February 21st, 1879. Since that time, a number of improvements, dictated by experience, have been made in the details of the furnace and fittings; and the recent roilclusion of a long and successful blast presents a convenient opportunity for a description of the works and a statement of the results of practice. The accompanying drawings will show the general arrangement of the works. The furnace, Plate I., Figs. 1 and 2, is 75 feet high by 19 feet bosh. The hearth is 11 feet 4 inches in diameter, with seven tuyeres 5 feet 6 inches above hearth-line. The tuyeres project 9 inches into the furnace, making the interior tuyere-circle 9 feet 10 inches in diameter. The front is a modification of Luermaun's

Jan 1, 1886

By AIME AIME

To accompanying photograph of the plant of the Beattie Gold Miner Limited, at Duparquet,. Quebec, is taken from the east and shows the open-pit from which the ore is taken during the summer. The buildings on the level ground above the open-pit are the change rooms, steel shop hoist building, compressor building, machine shop, warehouse, carpenter shop, and oil house. The main five-compartment shaft is shown west of the hoist building. The crusher plant adjoins the headframe and a long conveyor transports the fine ore

Jan 1, 1936

By J. F. Abel, F. T. Lee

Subsidence is controlled by a complex com¬bination of mining and geologic factors. For example, a compilation of worldwide data shows that, as the percentage of shale in the overlying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the over¬burden appears to cause a more than twofold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted, the smaller percentage of that thickness shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room-and-pillar panels de¬pends on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1984

By D. K. Deardorff, Earl T. Hayes

An improved technique is described for the accurate determination of melting points of metals in the temperature range 1500' to 2500°C. The improvements consist of gradient heating and refinements in cavity preparation to obtain true black-body conditions. The melting point of hafnium, as determined by this method, is set at 2222°±30°C. This is over 200°C higher than one of the values reported earlier. Discrepancies in the previously reported values for the melting point of hafnium are explained. The melting points of zirconium and titanium are found to be 1855O±15OC and 1668°±10°C, respectively. Reproducibility of results was ±3OC. PRIMARILY, this report is being made to correct a 1975o±25oC1 value for the melting point of hafnium, and to present an improved method for melting point determination. As a matter of interest, the technique was also applied to determining the melting point of zirconium and titanium. There is a wide difference in the melting point of hafnium as reported by competent investigators. DeBoer and Fast' reported a value of 2230°±500C, and later work of McPherson, as reported by Aden-stedt, placed the melting point at 1975o±25oC. Zwikker" calculated that the melting point was 2430°C. In resolving this discrepancy, improvements were made in the procedure for determining the melting points of refractory metals in the range 1500" to 2500°C. Special techniques are necessary to determine the melting point of these metals accurately. Since the metals oxidize in air above 900oC, the determinations must be carried out in an inert gas or vacuum. Also, every known refractory contaminates them to some extent. In addition, the attainment of true black-body conditions is always difficult. DeBoer and Fast actually determined the melting point of Hf-Zr as-deposited iodide process alloys and extrapolated to 100 pet Hf. McPherson employed a tungsten wire suspension similar to that described by Schramm, Gordon, and Kaufmann,1 and used hafnium metal produced by the iodide process. There was no apparent reason for the wide spread in melting points, since the quality of the metal was very good and the work was under the direction of highly competent investigators. Retracing some of this work revealed one understandable error in the case of hafnium, and led to development of an improved technique for determining melting points of reactive metals in the range 1500" to 2500°C. Material Crystal bar hafnium, zirconium, and titanium were used for this work, with analyses as shown in Table I. The hafnium was of the highest purity that has been prepared, though not as pure as the zirconium and titanium. At the instigation of the Pittsburgh Area Office of the AEC, a special lot of Hfo2 was purified, converted to the tetraflouride, and bomb-reduced with calcium, all at the Iowa State College Laboratories. This crude hafnium metal was then refined by the iodide process at the Foote Mineral Co. All specimens were cut with a Sic wheel, ground, pickled, and dried carefully before use. Procedure General Tungsten Suspension Method—In this method, a small specimen is suspended by a fine tungsten wire in a slender, induction-heated tungsten or tantalum cylinder, all under vacuum. The melting point is determined by heating the specimen slowly while observing it with an optical pyrometer focused upon a portion of the specimen that radiates as a black body. This means that there should be no reflected radiation, either from colder objects near the pyrometer or from hotter surfaces. The induction heater would be the only hotter object and, if it is slender enough, the specimen will attain the same temperature. Often a slender hole is drilled into the specimen as a source of black-body radiation. This was the general method used by McPherson in obtaining his value of 1975°C for the melting point of hafnium. In trying to repeat this work, it was found that the points of contact between the

Jan 1, 1957